After unplugging and moving my pxi-1002 it will not power on

need to get this thing powered back up ASAP. have presentation using it on thursday.

I'll let you know of some possible reasons for this, but I might need more information to go off of. I'll just list off my thoughts:
1. The chassis is just not getting power: It isn't plugged in, that particular outlet is bad, a surge protector is not working correctly, etc. You mentioned moving the chassis, does it work back in its old location?
2. There are no modules plugged into the controller: I don't have a 1002 to check this, but I know that the 1006 will not power on unless the minimal load is met... meaning it needs to have a module or controller actually in the chassis.
3. Too much power draw from module: If a pin was bent somehow causing a short to ground, that could be a possible problem. Or, a particular module just might have issues by
itself. What do you have in your chassis? Try removing everything but the controller. If it boots up, then you can shut down and insert different modules to isolate the problem.
If none of this helps, let me know and I'll see what else I can find out. Any information you can provide would be great. I hope this gets worked our before Thursday.
Best Regards,
Jeremy R.
NI - Applications Engineer

Similar Messages

  • After downloading and installing software for AirPortExtreme, Skype will not open.

    After downloading and installing new software for AirPort Extreme from the Appstore, Skype will not open.

    Did you repair permissions and restarted your computer after the installation? 
    Skype has their own forums for Mac users.  You should post there if the above does not work. 

  • Iphone 4, purhcased 4/12, reluctant to turn on after fully expended battery in the past,  now will not power on, communicate w/ itunes, tried restore -error 3194, then error 1600.  help me please...do I have a warranty?

    I purchased an Iphone 4 in April of 2012.  I always keep it on and charge it every night.  I have had some trouble turning, a couple of times, in the past.  It was simply reluctant to turn on after allowing the battery to be completely expended and has behaved the same way after being manually turned off.  I have again allowed the battery to completly die and turn off the phone.   This time it will not turn on at all.  I have tried various combinations of pressing and holding home and power to no avail.  I plugged it in to the computer, but Itunes will not recognize it as my phone.  Itunes is labeling it "Iphone" and has requested that I restore the phone in order to use it with Itunes.  Itunes states that "has detected an Iphone in recovery mode".  I, reluctantly, attempted to restore the phone.  After waiting quite a while on a "software update" to download, it said preparing Iphone for restore and then said "unable to restore Iphone, unknown error - 3194".  I read, online, that I needed the most recent version of itunes in order to restore.  So I upgraded Itunes and restarted the compluter.  On the second, and all subsequent attempts to complete the restoration, I am prompted with a message stating "unable to restore IPhone, unknown error - 1600".  My computer also attempted, and I believe, successfully, installed new device driver software for iphone4 (DFU mode).  Any assistance would be greatly appreciated.  Also is my phone, purchased 4/12, under any service or replacement warranty.  I truly feel it should be easier to turn on and I did not even want to restore the phone, I just need to use it. 
    Thank you,
    Geoffrey

    I am reading on this site about the error I am getting and it wants me to change some files that I am not comfortable messing with. Mainly because it is like a foreign language. Will the store do this for me or tell me if it is neccessary?

  • Iphone 4 will not power on and is not charging

    iphone 4 was charged and suddenly stopped work went dark,  Will not power back on, will not charge.  Any suggestions on cause or fix???

    Hi daj1202,
    That definitely doesn't sound good. Lets see if we can isolate this issue further:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIs and corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 15 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen. Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    Thanks,
    Matt M.

  • I have an iphone 4 and after updating it to the ios5 software, it will not allow me to activate nor allow me to leave the setup page. i cannot even restore it. does anyone know what to do?

    i have an iphone 4 and after updating it to the ios5 software, it will not allow me to activate nor allow me to leave the setup page. i plugged it into itunes and it is stuck there too... i cannot even restore it. does anyone know what to do?

    I have had this same issue but thankfully fixed it. Follow he steps below:
    Sync your iPhone with you iTunes therefore your info is backed up. Unplug your phone.
    Go to Settings > Reset > Erase All Content and Settings
    Once your phone has reset and come back on answer the question until it asks if you want to back up from itunes Click this then plug your phone in.
    After everything has sync'd back to your phone everything should work fine.
    Hope this helps.

  • HT3964 my macbook air keeps coming up with a message" are u sure u want to shut down..etc" after which it switches off by itself. now it's off and will not power on altogether. any suggestions?

    my macbook air keeps coming up with a message" are u sure u want to shut down..etc" after which it switches off by itself. now it's off and will not power on altogether. any suggestions?

    Does it power on if you plug in the charger?
    But to be honest I see in your description it says 'Late 2011' so there is a good chance you have warranty right, I would take it to Apple store and let them sort it out

  • Hi, I just updated my mac from version10.6 to 10.9.3 os mavericks. i went to open iPhoto and it says "Your photo library will not be readable by previous versions of iPhoto after the upgrade." does this mean I have lost all photos i had in there?

    Hi, I just updated my mac from version10.6 to 10.9.3 os mavericks. i went to open iPhoto and it says "Your photo library will not be readable by previous versions of iPhoto after the upgrade." does this mean I have lost all photos i had in there? It does not give me a choice, it just says quit or upgrade? p.s. i didn't realise ther was  a way to back up my computer beforehand, which i am guessing this is time machine?

    1. No, you haven't.
    2. Back up the iPhoto library(this can be done through Time Machine or by dragging it to a drive, partition, or disk image formatted as Mac OS Extended) and then click Upgrade.
    3. Aside from Time Machine and drag-copying items from your home folder, programs such as the Disk Utility, Carbon Copy Cloner, and SuperDuper can make backups.
    (108026)

  • After resetting my phone to factory settings, it will not turn on. When i press the power button a white screen and black apple pop up. it stays on that screen and will not go to the home screen, it will just die. please help!

    after resetting my phone to factory settings, it will not turn on. When i press the power button a white screen and black apple pop up. it stays on that screen and will not go to the home screen, it will just die. please help!

    Make sure it is charged for about 10min using the adapter, then connect in recovery mode, explained in this article:
    If you can't update or restore your iOS device

  • IPad 3 needs to be unplugged and re-plugged USB before iTunes will Sync it... Huh?

    My iPad 3 needs to be unplugged and re-plugged USB before iTunes will Sync it...
    It can be plugged in and online in iTunes, with the home screen showing, and iTunes just hangs when I try to Sync it, unless I unplug and re-plug it USB
    Anyone seen this before?

    Yes, but I charge my iPad with my iMac, so it's connected most of the time, and to have to unplug/replug it to sync it is nuts.
    Why does it hang when I hit "Sync" ? It should never hang. Either I am doing something wrong, or This Is A Bug.

  • My ipod gen 3 is frozen after the latest update from itunes,it will not power on or restore without error.Itunes is up to date,changed usb ports,even uninstalled and reinstalled all apple software, error 1601 during restore

    My ipod gen 3 is frozen after the latest update from itunes,it will not power on or restore without error.Itunes is up to date,changed usb ports,even uninstalled and reinstalled all apple software, error 1601 during restore

    Hello, VvioletT. 
    Thank you for visiting Apple Support Communities.
    I see you are experiencing issues syncing your iOS device.  Here are a couple articles that I would recommend going through when experiencing this issue.
    iOS: Troubleshooting USB-related alerts when syncing
    http://support.apple.com/kb/TS5254
    Resolve issues between iTunes and security software
    http://support.apple.com/kb/ts3125
    Cheers,
    Jason H.

  • After downloading and installing additional content, no sound will play. Logic has no connection to sound library. No level meter activity. Right before i installed additional content I was working on a project, and everything was OK.

    After downloading and installing additional content, no sound will play. Logic has no connection to sound library. No level meter activity.
    Right before i installed the additional content I was working on a project, and everything was OK. What is wrong. How do I make Logic reconnect to the instrument files?

    Whitelab Records wrote:
    So, 20 views and nobody's anybody the wiser?
    A small update to this issue....
    I have been trawling the forums to find an answer but to no avail...
    And... I've tried exporting and bouncing individual stems and the full session, either by muting all bar the stem or soloing the stem.....and still nothing.
    Same problems.....everything is audible in audition but nothing plays on playback.
    Since the 'prelisten' channel strip is Solo safe this would indicate that you have a track or channel strip soloed somewhere else, out of sight. Are the Mute buttons on your channel strips blinking?
    To view all objects in your mixer, click the button. You may have to scroll sideways to check the whole mixer.

  • After loading the latest Aperture 3 update, aperture will not load and it appears to have corrupted 10.6.  10.6.7 now appears to be missing from the computer and my administrator status has changed to standard.

    After loading the latest Aperture 3 update, aperture will not load and it appears to have corrupted 10.6.7. and now appears to be missing from the computer and my administrator status has changed to standard.  Update Software says I need to do update to 10.6.7 which I can't do because administrator privileges are gone.   I didn't back-up with Time Machine ,BAD, but I have all files backed-up on another hard drive.  Should I just reformat and start over?  Any ideas or help would be appreciated.

    PROBLEM SOLVED! For me at least!
    Apple Support gave me the clue - I had run Migration Assistant, and it had obligingly replaced a system file (/Library/Frameworks/PluginManager.framework/Versions/B/PluginManager) with the equivalent from my old system.
    I reinstalled 10.6.7 using the DVD supplied and all is well.
    The moral is - don't use Migration Assistant.
    Along the way Apple Support provided me with a link to download Combo update 10.6.7: this could not be installed on my iMac.
    Hope this helps.

  • TS1713 My mac sometimes will not power up even though it is fully charged and no matter how many key's I touch will not bring it on. It comes on after about 10 minutes and I have to shut down about 6 windows before I can open up a browser.

    My mac will not power up even though it is fully charged. It only happens occasionally and when I try to power up after about 10 minutes it comes to life but has 6 or 7 windows that I have to close in order to open up my browser.

    1. Reset PRAM.  http://support.apple.com/kb/PH4405
    2. Reset SMC.     http://support.apple.com/kb/HT3964
        Choose the method for:
        "Resetting SMC on portables with a battery you should not remove on your own".
    3. Start up in Safe Mode.
         http://support.apple.com/kb/PH11212

  • TS1398 After leaving a wi-fi connection my iphone will not automatically connect to the internet via the 3G network unless I turn it off and then on again. Is there a setting that can be changed to overcome this issue?

    After leaving a wi-fi connection my iphone will not automatically connect to the internet using a mobile 3G network unless I turn my phone off and then back on again. Is there a setting that can be changed to overcome this?

    Then I'm at a loss. Mine has switched automatically from the start, favoring Wi-Fi, any of its registered networks, whenever available. Only thing I can think of is trying a Force Restart and see if that clears things up: hold down Home and Sleep till the screen goes black and a white Apple logo pops up. Release and allow it to restart.
    May be similar, when I got the i5 about 16 months ago, the local carrier was starting to roll out 4G service. The phone would regularly lose all carrier connection, voice and data. Haphazardly would reconnect when it felt like it afterwards. Initially did the Off/On dance to speed things up, but discovered that using Airplane Mode would do the same without the lengthier power cycle. After awhile, the carrier 'fessed they were having capacity issues and later the problem went away. So yours too may also be a carrier issue.

  • HP Pavilion a1123c - will not power on after being unplugged while in use

    So bit of panic:
    I've been using the above computer since 2007 with the expected wear and tear, slowing down. Today it was put through its paces and while on a multimedia-hwavy web page it became unresponsive to the point I could not even bring up the task manager to restart. Being a computer noob, I unplugged the computer to force a reset. It now will not power on with or without the power source. While plugged in the LED flashes rapidly. When unplugged the LED flashes but more slowly. I have tried flipping the voltage switch on the back but still my computer won't turn on.
    I have all of my digital photos on this computer and am terrified of losing everything. What should I do? Is there hope of the data being salvageable? Thank you all so much.

    Assuming erico 's advice fixes the situation, please make backups of the important data -  such as photos or other important documents to a DVD or flash drive or external hard drive.
    If the power supply troubleshooting guide does not fix the problem, there are ways to still make the backups of that important data, on a working computer from the failed computer.  Just come back with the report on whether the advice from erico worked or not.
    {---------- Please click the "Thumbs Up" to say thanks for helping.
    Please click "Accept As Solution" if my help has solved your problem. ----------}
    This is a user supported forum. I am a volunteer and I do not work for HP.

Maybe you are looking for