After update Mac OS 10.9.1 Trim Enabler does not work anymore!

After updating from Mac OS 10.9.0 to 10.9.1 the program Trim Enabler does not work anymore and my 4 SSDs from Samsung and Kingston are no longer supported.
What can I do?
Should I scrap my SSDs?
Why does Apple do such things?
Will Apple that I switch to Windows? There Trim works with all SSDs and BluRay will not boycott!

Apple does not support TRIM for SSDs that were not factory
installed and TRIM Enabler is a hack to get around this. Any
hack is always subject to being disabled, or worse, with any
system update whether it is OSX or Windows.

Similar Messages

Mac os 10.4.10 software update problem -- my mac does not work anymore :(

hello!
i have a powerbook G4- PPC. just today, i did a software update of my OS to 10.4.10 (it was the available update version according to the automatic uptae) and during the final stage of the installation, it says "a problem was encountered...installation package is moved to trash"
when i browsed my mac, my apps does not work anymore!!! they just bounce from the dock when i clicked it but it won't open any window. i emptied the trash and restarted my mac but sadly, it just boot but won't continue to the log in part, only in the silver window with the apple logo and mac os x tiger... and the mouse just turns into the color wheel. i waited for 30 mins and nothing happened.
i don't have a startup disc because the mac is a gift and it was long time ago. is ther a software i can use to fix or revert the changes of the unsuccessful OS update? why is there always a problem when i do OS update? isn't apple software stable?
My mac problems' driving me crazy!!!

There are no guarantees, but following this procedure when installing updates and upgrades on your Mac will go a long way towards avoiding unpleasant after effects and ‘post-update stress disorder’.
It is also worth noting that it is an extreme rarity for updates to cause upsets to your system, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
So before you do anything else:
If you can, make a full backup first.
Turn off sleep mode for both screen and hard disk.
1. Repair Permissions (in Disk Utility)
2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
3. Download the correct version of the COMBO update from the Apple download site. If your car runs on gasoline you would not want to fill the tank with diesel, so don’t try to install the PPC updater on an Intel Mac!
If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
Using the Combo updater ensures that all system files changed since the original 10.4.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.4.9 to 10.4.10. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
Now proceed as follows:
4. Close all applications.
5. Unplug all peripherals except your keyboard and mouse.
6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
8. Once your Mac is awake, repair permissions again, and you should be good to go!
If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious!
9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them 10.4.10. compliant. Give them a weeks or two while you regularly check their websites for updates. This applies particularly to plug-ins for Safari 3.
N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.
Lastly, Apple's own article on the subject of Software Update may also be useful reading:
http://docs.info.apple.com/article.html?artnum=106695

HT204135 I update my Mac to version 10.9.2 and now my printer does not work anymore. I did all the software updates and I do not understand why my mac does not recognize the printer anymore?

I update my Mac to version 10.9.2 and now my printer does not work anymore. I did all the software updates and I do not understand why my mac does not recognize the printer anymore?

Go to the website of the manufacturer of your printer and check to see if they have released an updated driver for your particular model.

Enter key does not work anymore in address bar after FF update

After the update the Enter key does not work anymore. Neither when I type the url directly, nor when I select it from the history.
In short FF has become unusable. Now I need to install and use a less crappy browser. Extremely sloppy, amateuristic update.

see if this is helpful : go to Tool > Options > Advanced > General tab > Browsing and '''Uncheck''': "Use hardware acceleration when available" .

After updating to 4.4.2 the notification light does not change colors. How do I fix this?

After updating to 4.4.2 the notification light does not change colors. It only blinks one color. How do I fix it?

Hello Saralynn43. Getting new updates is always fun, but then there are certain changes that can take some getting used to! This may be one of these cases where there may have been a change done to the notification system. What are the notifications that have been affected with the color change? Let us know as we'd like to look into this for you. Thank you.
NicandroN_VZW
Follow us on twitter @VZWSupport

After updating my iphone 4 to ios5, my iphone does not sync

After updating my iphone 4 to ios5, my iphone does not sync music and contacts with itunes. These are the one i noticed so far!!
My new music in itunes will not update on my iphone?
My new contacts will not update on my computer address book?
Any ideas on whats the problem?

Did you check how many entries do you sync in the iPhone? Under "Mail, calendar and contacts" options on the Settings app, you need to make sure that you have enough entries syncing in your iCal.
By default I think it's the last 30 entries, but you can set it up to view all entries.
Also make sure that your calendars are selected as viewed.
Good luck,
Sergio

I have a Power Mac G5 quad core (2006) and it does not work.

I have a Power Mac G5 Quad core (2006) and it does not work.The status light flashes twice and the fans blow full blast. The display does not show anything. Does anybody know what is wrong with my mac.

Can you count the beeps or flashes?
1 beep = no RAM installed
2 beeps = incompatible RAM types
3 beeps = no good banks
4 beeps = no good boot images in the boot ROM (and/or bad sys config block)
5 beeps = processor is not usable
In addition to the beeps, on some computers the power LED will flash a corresponding number of times plus one. The LED will repeat the sequence after approximately a 5-second pause. The tones are only played once.
Note: In this case, a flash is considered to be 1/4 second or 250 ms or greater in length.
http://support.apple.com/kb/HT1547
Might be time to replace the PRAM Battery, 4 years is close to their lifespan, far less if ever without AC power, & can cause strange startup problems...
See which one your G5 has, should be the 1st one ..
http://eshop.macsales.com/item/Newer%20Technology/CR2032/
http://eshop.macsales.com/item/Newer%20Technology/BAA36VPRAM/
If you're sure the RAM is good, try the Hair Dryer trick...
http://discussions.apple.com/message.jspa?messageID=13240047#13240047
https://discussions.apple.com/message/15223603#15223603
https://discussions.apple.com/message/15499912#15499912
https://discussions.apple.com/message/15613068#15613068
https://discussions.apple.com/thread/3270112
https://discussions.apple.com/message/16053892#16053892
No power light at all...
https://discussions.apple.com/thread/3692775?tstart=0
It can show on any G5, and even many other computers & electronic devices of the period.
http://www.macintouch.com/reliability/pmg5.html
http://lowendmac.com/ppc/power-macintosh-g5.html
And see this last one in particular...
https://discussions.apple.com/message/16781690#16781690
Heat gun better...
https://discussions.apple.com/thread/3916312?tstart=0

While updating my ipad to new software through itunes it got stuck and does not work anymore - it just displays the screen with symbols of itunes and the cable to connect to it - help - what should i do?

while updating my ipad to new software through itunes it got stuck and does not work anymore - it just displays the screen with symbols of itunes and the cable to connect to it - help - what should i do?

Disconnect the iPad, do a Reset [Hold the Home and Sleep/Wake buttons down together for 10 seconds or so (until the Apple logo appears) and then release. The screen will go blank and then power ON again in the normal way.] It is 'appsolutely' safe!, reconnect and follow the prompts.
If that does not work then see here http://support.apple.com/kb/HT1808

I am using Windows 7 64-bit. After installing Photoshop Elements 13 and trying to run it I always get the message: Photoshop does not work anymore. And it doesn't.

I am using Windows 7 64-bit. After installing Photoshop Elements 13 and trying to run it I always get the message: Photoshop does not work anymore. And it doesn't.

Hi Hardy Tasso,
Are you seeing this problem since first launch of PSE13 after installation or recently?
Please try:
Keep Ctrl + Alt + Shift keys pressed while launching PSE13 Editor and click OK on the dialog that comes next.
Thanks,
Anwesha

I am new to mac air. Today i installed (unsuccessfully!) MAPLE16 on my mac book air. Now since it does not work properly (it also does not appear in applications) i decide to delete it. I could not remove it from launchpad . i need urgent help

i am new to mac air. Today i installed (unsuccessfully!) MAPLE16 on my mac book air. Now since it does not work properly (it also does not appear in applications) i decide to delete it. I could not remove it from launchpad . i need urgent help from your side.

Any third-party software that doesn't install by drag-and-drop into the Applications folder, and uninstall by drag-and-drop to the Trash, is a system modification.
Whenever you remove system modifications, they must be removed completely, and the only way to do that is to use the uninstallation tool, if any, provided by the developers, or to follow their instructions. If the software has been incompletely removed, you may have to re-download or even reinstall it in order to finish the job.
I never install system modifications myself, and I don't know how to uninstall them. You'll have to do your own research to find that information.
Here are some general guidelines to get you started. Suppose you want to remove something called “BrickMyMac” (a hypothetical example.) First, consult the product's Help menu, if there is one, for instructions. Finding none there, look on the developer's website, say www.brickmyrmac.com. (That may not be the actual name of the site; if necessary, search the Web for the product name.) If you don’t find anything on the website or in your search, contact the developer. While you're waiting for a response, download BrickMyMac.dmg and open it. There may be an application in there such as “Uninstall BrickMyMac.” If not, open “BrickMyMac.pkg” and look for an Uninstall button.
You generally have to reboot in order to complete an uninstallation.
If you can’t remove software in any other way, you’ll have to erase and install OS X. Never install any third-party software unless you're sure you know how to uninstall it; otherwise you may create problems that are very hard to solve.
You may be advised by others to try to remove complex system modifications by hunting for files by name, or by running "utilities" that purport to remove software. I don't give such advice. Those tactics often will not work and maymake the problem worse.

Migrating V9 to V10: Update XML Fragment CLOB does not work anymore

I have an XML Schema that contains an element, named Operazione, mapped to a CLOB.
I just migrate to Oracle 10.1.0.2.0 from version 9.2.0.2.0 and the code I developed does not work anymore.
To get a CLOB on v 9.2.0.2.0 I issued the following statement:
select extractValue(value(p),'/operazione.log/Operazione') from XMT_OPERAZIONE_LOG p
where existsNode(value(p),'/operazione.log/Journal[NumeroElettronico=1234567890]') = 1
To make it working on V10 I have to change it as follow:
select extract(value(p),'/operazione.log/Operazione').getClobVal() from XMT_OPERAZIONE_LOG p
where existsNode(value(p),'/operazione.log/Journal[NumeroElettronico=1234567890]') = 1
So using extract intead of extractValue and adding getClobVal() I was able to read the CLOB.
The problem that I was not able to solve is related to CLOB update. In V9 just adding the âfor updateâ clause I was able to change the CLOB value on DB.
In V10 if I run the V9 statement I get the error:
ORA-03113: end-of-file on communication channel
If I use the statement modified for V10, adding the âfor updateâ clause, I get the CLOB and I can change the CLOB value but nothing goes on the DB. Probably I am working on a copy of the DB CLOB.
If I remove the getClobVal() I get an OPAQUE type that I can use on a XMLType but, still, nothing is stored on DB.
Any suggestion ?
I tried with both OCI and Thin Client

Can anybody help me ?
Is it better to use different strategies ( eg. Stored Procedure, DBMS_XMLSTORE etc, etc. ) ?
Any experience updatating XML Fragment CLOB on Oracle V10 ?

Hello! I have installed Photoshop on PC WIN 7 64bit. When I store first time a Photoshop docuument, it works fine - after re-opening and doing changes I trying again to store it - it does not work anymore! First it does not accept the name (message "It ca

Hello! I have installed Photoshop on PC WIN 7 64bit. When I store first time a Photoshop docuument, it works fine - after re-opening and doing changes I trying again to store it - it does not work anymore! First it does not accept the name (message "It can not be stored because the nam is invalid" With 2. trial it tells me that the data is blocked and I don't have the rights - and I should chenge them. But I am working as the Admin on my PC - and each trial to change the rights of the data is as well not possible because of missing rights - even I am Admin! I must always store the data with a new name, then it works, but I also cannot remove the old datas or shift them into the waste paper - because of no rights! -- sorry for not perfect english, I am German native speaker! Tahnks a lot for help!

Hi,
I am using a Nvidia 4200M adapter in my Laptop, Driver 266.96, Direct X 11
In my desktop I am using an ATI XFX 6950, latest revision drivers (I am not at home right now so I cant get that info).
The issue I did describe above, but it was a long explanation.
In some flash games the game files load initially and get as far as the "click to start" button. Then the flash area usually goes either all white or all black (usually depending on the falsh game default background color) and then it stays that color. Cant see anything after hitting start (usually most games have an intro video or animation before the game starts, but I cant see any of it.
For the very few games that do start, the flash game or application does not seem to work correctly in that when the rare game starts, it wont save any game files or save files to the pc and so if I exit the game (navigate away to another page or close browser) and then later come back, even though I click the option to save games (and ensure that the flash application slider shows it can save files and lots of space) it does not save and I have to start from the beginning all the time.
More explanation I gave above.

After sending sound from find my iphone, now ipad does not work

after sending sound from find my iphone, now ipad does not work
it can't be unlock and scrren is blank, only siri works

Try a reset: hold down the home button along with the sleep/wake button until you see the apple, then let go.

Just updated my iPad with iOS 7 and now internet does not work anymore, how to fix if???? Desperate

Just updated my iPad with iOS 7 and now internet does not work anymore, how to fix if???? Desperate

Try resetting your iPad:
Double click the Home button. Slide up with one finger on ALL your apps to close them.
Then, Press the Sleep/Wake button + Home button and hold 15 seconds or until you see the Apple logo.
This will reset your device without erasing data, apps or settings.

My new orkut page does not works anymore after uptading firefox from Firefox v9.0.1 to 10

My new orkut page does not works anymore after I uptaded this morning my browser firefox from Firefox v9.0.1 to 10 . How can I find that version mozilla Firefox v9.0.1???

Hello, friend. Thank you so much. I've already solved the problem once you sent me that link.
Cheers!

After update Mac OS 10.9.1 Trim Enabler does not work anymore!

Similar Messages

Maybe you are looking for