After upgrade exchange owa, ecp and outlook stop working

Yesterday I installed the updates that Microsoft had released. Unfortunate as it looks like OWA, ECP and Outlook stopped working after this installation. See picture for the updates were made.
What you are greeted by when besker OWA and ECP is a blank page. Is anyone had the same problem and knows how to fix this?
Or is there a way to back these updates?
Jesper B

Hi Jesper,
Is there any update? Have the issue been resolved?
The updates are all for Windows server 2012 R2. What's your Exchange server version? Additionally, please check the following in IIS Manager:
a. In IIS manager > Default Web Site, make sure Anonymous Authentication is Enabled in Authentication.
b. Double-click SSL Settings, confirm that "Require SSL" is checked on the root of the default website.
c. Restart IIS service by running iisreset /noforce from a command prompt window.
If possible, please collect more event logs in Event Viewer for further analysis.
Regards,
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]
Winnie Liang
TechNet Community Support

Similar Messages

After upgrading to IOS8.1 my microphone stopped working. cannot make a call, cannot record a voice memo, but Siri works !!!

after upgrading to IOS8.1 my microphone stopped working. cannot make a call, cannot record a voice memo, but Siri works !!! Surely this must be software since I presume there are not two microphones, one for Siri and one for everything else. Tried resetting, rebooting, switching off noise cancelling. What else is there?

Hi there hansadj,
You may find the microphone troubleshooting steps in the article below helpful.
If your voice is too faint or sounds unclear using iPhone, or iPod touch
-Griff W.

Yesterday after upgrading the Cisco AnyConnect app, it stopped working; Today, the app is not available anymore from the apple store, what happened?

Yesterday after upgrading the Cisco AnyConnect app, it stopped working; Today, the app is not available anymore from the apple store, what happened?

There is an explanation in the following link in the section "What's new in version 3.0.09440" that there was a problem with the update. It's available again now. https://itunes.apple.com/us/app/cisco-anyconnect/id392790924?mt=8

After upgrade to 5.1.1 bluetooth stop working with handsfree

Hi there, I have a buildin handfree in my renault scenic 2010 model.After upgrade to 5.1.1 bluetooth crash handsfree in my car.I can't use my phone during drive. I don't see any bluetooth device connected to. Interesting thing is that before upgrade device reconnect several time after connect successfully. regards

Try performing a system repair using PC Companion as this will often fix issues - This will factory reset your phone and erase all data so best to backup before you begin
Switch off your phone and unplug from Pc (Hold volume up and power for around 10 seconds)
Start PC Companion and select Support zone then Update my phone/tablet then in Blue Repair my phone/tablet and follow the on screen instructions - When prompted connect your phone still switched off holding volume down or back button - This should start the repair or reformat process
If you are using Windows 8/8.1 or a 64bit operating system then adjust the settings for PC Companion and run in compatibility mode and chose Windows 7 or XP

Upgraded to iOS 7 and speakers stopped working

They work for the phone ringing and the alarm only. No sound on videos or music. Can't hear iTunes Radio etc..

Your phone might be on do not disturb mood... So, when it's locked, you receive no calls. If you see a crescent at the top of your screen, go to setting, do not disturb, and turn off the manual
Hope that help

After upgrading Exchange Server 2007 to SP3 with update rollup 13, OWA not working

Hi,
We have just installed Service Pack 3 and update rollup 13 on our Exchange Server 2007, but unfortunately our OWA has gone inaccessible.
PROBLEM- The following error comes up when we try to access OWA :
Exception
Exception type: Microsoft.Exchange.Clients.Owa.Core.OwaInvalidConfigurationException
Exception message: Object reference not set to an instance
of an object.
Call stack
Microsoft.Exchange.Clients.Owa.Core.OwaConfigurationManager.CreateAndLoadConfigurationManager()
Microsoft.Exchange.Clients.Owa.Core.Globals.InitializeApplication()
Microsoft.Exchange.Clients.Owa.Core.Global.ExecuteApplicationStart(Object sender, EventArgs e)
Inner Exception
Exception type: System.NullReferenceException
Exception message: Object reference not set to an instance
of an object.
Call stack
Microsoft.Exchange.Clients.Owa.Core.Configuration.CheckPublicFolders(ADSystemConfigurationSession session, ADObjectId[] pfdbIds, Boolean& allLegacy, Boolean& allLater)
Microsoft.Exchange.Clients.Owa.Core.Configuration..ctor(ADSystemConfigurationSession session, String virtualDirectory, String webSiteName, ADObjectId distinguishedName, Boolean isPhoneticSupportEnabled)
Microsoft.Exchange.Clients.Owa.Core.OwaConfigurationManager.LoadConfiguration()
Microsoft.Exchange.Clients.Owa.Core.OwaConfigurationManager.CreateAndLoadConfigurationManager()
ACTION TAKEN SO FAR :
1. Removed OWA virtual directories and recreated them again.
2. IIS has been reset.
3. Restarted the HUB/CAS server.
4. Created public folder database.
Even after doing all these activities, owa is still inaccessible. Please help.
Regards,
Ankur

Hi Ankur,
From your description, you can't access to OWA after upgrading Exchange server 2007 to SP3 rollup 13. Firstly, please locate to C:\ExchangeSetupLogs and make sure that it is a successful installation. If not, this issue often occurs.
If it is a successful upgrading, please follow the steps below for troubleshooting.
1. Open IIS Manager, click Default Web Site -> Authentication, make sure that Anonymous Authentication and Windows Authentication are enabled.
2. Click Default Web Site -> SSL Settings, check "Require SSL" and click Ignore.
3. Click Default Web Site -> HTTP Redirect, check Redirect (enter your
https://URL), check "Only redirect" box and Status code Found 302.
4. Expand Server Configuration -> Client Access ->double click owa ->Authentication tab. Check the Basic Authentication and check the Use forms-based authentication button Logon Format: Domain\user name.
Hope it helps.
Best regards,
Amy Wang
TechNet Community Support

Ovi and syncing with Outlook stopped working after...

I recently upgraded to Ovi 2.2.1.23 and syncing of calendar and contacts stopped working.
The reason seem to be that when I try to connect to Outlook from the sync menu, Ovi freezes.
Everything was working fine before and I just upgraded Ovi, nothing else.
Any idea what to do? Ive tried to uinstall and reinstall Ovi but no change.

Gawd, how I love this Apple forum. At least microsoft has MVP's that come out and help others.
I too have this problem and I have Gmail and all my notes in my Gmail (on iPhone or iTouch) are not synched only those on my iPhone or iTouch.
The options i have for default account are:
Accounts
iPhone or iTouch
Gmail
I have notes in my Gmail. How do I get them to my iTunes?

How can I retrieve my calendar info that was sucked from my iPad 2 after upgrading to OS V and backing up to iCloud (using Windows XP computer with Outlook)?

How can I retrieve my calendar info that was sucked from my iPad 2 after upgrading to OS V and backing up to iCloud (using Windows XP computer with Outlook)?

I think (and I'll double check) only the BBLink events will sync on a wired USB sync. I'm fairly certain of that.
You'll need to use your calendar syncing via an EAS email account (outlook.com, for instance, is free) to sync wirelessly. It works great. I use it and was a former tied to the USB sync guy as well... and I thought I was gonna die a painful death without it. I found more freedom this way.
This explains the process. But I don't think you'll get BBM Groups to sync.
http://supportforums.blackberry.com/t5/BlackBerry-Z10/How-To-OTA-Sync-BB10-and-non-BES-Outlook-Overv...
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Toupad Tapping and Scrolling stopped working after Windows 10 Upgrade

Hi, I upgraded my OC to Windows 10 today, after the upgrade tapping and scrolling stopped working on the synaptics touchpad. the toucpad only finctions as a pointer now. for taps/Clicks i always have to use the buttons below the touchpad. It was working fine before the upgrade, the earlier OS was Windows 7 I have checked for driver updates but i get a message that the drvier is up to date.I have check the device setting and confirmed that tapping and scrolling is enabled.I have also done a device reset. Nothing solved the problem, i also did not find a relevant answer on the forums.Also, the same problem did not happen with my other HP laptop (Notebook PC) which was also upgraded to windows 10 recently. Does anyone have a solution? Regards,Siddharth.

, Hello and thanks for posting on the HP support forums. What you will need to do is the run the Windows Update Fixer tool. Here is a link to help you with that. Make sure you run all updates including optional. Fix Microsoft Windows Update Issues If that fails to work the only other option is to roll your system back to the original supported operating system that came with your notebook. Thanks again for the post and have a great day.

Bookmark bar and menu stop working after awhile on Firefox 12

I have upgraded to Firefox 12. Everything works fine when I start up Firefox, but after some amount of use (and I can't always reproduce this) eventually when I click on bookmarks in my Bookmark Bar or from the Bookmark menu, nothing happens. Firefox doesn't load the bookmark. If I open the "Show All Bookmarks" window and click on bookmarks there, they load fine and then the menu and bookmark bar suddenly start working again. If I close the "Show All Bookmarks" window the Bookmark Bar and menu stop working again.

Hi ischou,
I haven't heard of this particular issue, but you might want to try starting Firefox in [[Safe Mode]]. Let is sit for a while as you described above and if you don't have the issue while all of your add-ons, extensions, and themes are disabled, you can try adding them back in one by one until you find the culprit. You should look at the [https://support.mozilla.org/en-US/kb/Troubleshooting-extensions-themes Extensions and Themes troubleshooting guide ] and the [[Troubleshooting plugins]] article as well.
You could also try [https://support.mozilla.org/en-US/kb/Managing-profiles?s=create+a+new+profile&r=2&e=es&as=s#w_creating-a-profile Creating a new profile].
Hopefully this helps!

Upgraded to 10.7.2 and Spacenavigator stopped working

Upgraded to 10.7.2 and Spacenavigator stopped working in Archicad 14. Anybody else having similar problems? It was working ok on 10.7.1 but has completely stopped working now.

For those people who are having this issue. Open System Preferences and log out of MobileMe and then restart your computer. After it has restarted, open System Preferences and log back into MobileMe. Restart your computer again and the problem should be resolved. I hope this helps. It worked for me. Good luck! Cheers, jtw335
P.S. The CSConfigDotMacCert message only displayed when I was logged into my Standard account. If I logged in using my Administrator account it would not display, I'm assuming because it didn't need the administrators permission.

Hi Team, Showing Yellow icons after every 15 to 20 Min and internet stop working.when we enable- disbale the network connection then will internet start working fine.Some time network connection is disable but when we renable that connection it will st

Hi Team,
Showing Yellow icons after every 15 to 20 Min and internet stop working.when we enable- disbale the network connection then will internet start working fine.Some time network connection is disable but when we renable that connection it will stuck on enabling
and will not renable till i am not restart that machine. I have 350 Machine in network but facing this issue in 25 machines. Kindly help me on this issue .
Regards
Sahil bhateja

Hi，
So switch a LAN card fix this issue...seems a compatibility issue or maybe some packs or programs you installed recently cause this issue.
Have you manually check the network adapter driver from the PC's manufacture website? sometimes, it will be a time delay before Microsoft push out the driver update.
Check if issue exists in safemode with network, this mode will launch Windows with limited sets of files and drivers.
if you have a restore point, restore the pc to a previous point at which the pc is functioning fine.
Yolanda Zhu
TechNet Community Support

Safari and firefox stop working after a few minutes of browsing, regardless of what site I'm on. I have to restart my computer to get internet access again but it only works for a few more minutes, then I have to restart again. Please help!

Safari and firefox stop working after a few minutes of browsing, regardless of what site I'm on. I have to restart my computer to get internet access again but it only works for a few more minutes, then I have to restart again. I don't get a spinning ball, it just stops working at whatever page it's on. I can close the program just fine but when I re-open it, either safari or firefox, it freezes trying to load the hompage. This started a few days ago after trying to stream a movie on my computer. I'm on a Mac Air OS X Version 10.6.8 and have downloaded all updates. When I go into finder, it says I have over 80 gigs available. Is there some other memory cache that I need to check? Thanks so much for your help.

ejwoodall wrote:
It's not a router problem as I explained in my post. If it was a router problem then I wouldn't have the problem everywhere I go. It is an issue with the software.
Then I guess the millions of people running 10.5.7 with no issues are just hallucinating that their machines are working fine?
I'm not trying to belittle your issues; you're certainly having them and I know first hand how annoying an intermittent AirPort issue can be. (In fact, mine was due to an AirPort driver bug that no one else seemed to suffer from.)
The single best diagnostic you could do is take your system running 10.5.7 to an Apple Store, and try using their in-store network.
If your machine performs flawlessly, it may be a router issue.
If your machine has connectivity issues there, it may be a hardware problem with your machine.
There have been numerous people in multiple threads over the years who swore that an update was buggy because things used to work, but returned later to sheepishly admit that they took their machine in, a problem was found and fixed, and now their Mac works flawlessly with the newer software.
But simply reinstalling 10.5.5 in no way means the explanation of how firmware bugs may be at play here is incorrect.
In the context of that explanation, all you've done is possibly reinstall software that asks to add "2 + 3."

After upgrade to Yosemite, drag and drop for files does not work, destination folder crashes.

After upgrading to Yosemite, dragging and dropping files from one location to the destination folder, causes the destination folder crash. However, copying the file and then moving it works fine.
I'm not sure where to report bugs, but I figured this would be the best option

http://www.apple.com/feedback/ Feedback
https://bugreport.apple.com/ BugReporter

I have an Epson Perfection V100 scanner and can no longer scan after upgrading to Mountain Lion and Creative Suite 5.5. Any suggestions?

I have an Epson Perfection V100 scanner and can no longer scan after upgrading to Mountain Lion and Creative Suite 5.5. Any suggestions?

Check the Epson web site for updates to drivers and Epson scan software.

After upgrade exchange owa, ecp and outlook stop working

Similar Messages

Maybe you are looking for