After upgrade the firmware, it can't be initialize

Hi,
I use PCI-7344 and UMI-7764
and upgrade the motion software and firmware to 7.2 version
but I can't be initialize the motion card in MAX
the error code is -70038
由 ycw7 在 03-25-200601:53 PM 上編輯的訊息
====================
●LV Version：LabVIEW7.1
●OS：WindowsXP(SP1)
●Hardware：PCI-7344, PCI-6602, PCMCIA 6024E
Attachments:
error.jpg ‏122 KB

Hey ycw7,
After getting this error, I would recommend that you take the board out of the PC, uninstall the NI-Motion driver software, and make sure that any motion configuration files or any files regarding motion get deleted. Then do a reinstall of the NI-Motion 7.2, place the board back in the computer after the installation is complete, and this time try the board in a different slot, and see if you can initialize the board. If this doesn't work, then if you have another PC that you can install Motion 7.2 on, try it in another machine and see if you get the same error. If you still get this error, then you might want to try reverting back to an earlier version of NI-Motion, like 7.0, and see if you can get that to let you initialize the board. Finally, if none of these work, then you should contact National Instruments and work with them about what to do next. Let me know if you have any questions. Thanks, and have a great day. 
Regards,
DJ L.

Similar Messages

  • After upgrading the itunes, I can not find my ipad when it connects to the PC

    After upgrading the itunes, I can not find my ipad when it connects to the PC
    Before that, I can see an botton said my ipad. And then I can click it to operate my ipad

    Try this
    Go into the control panel. Add/remove programs. Uninstall iTunes, Apple mobile device service, apple application support. Then go out and redownload and reinstall iTunes and try again.
    There seems to be a glitch with a recent update and one way to overcome it is to just start over. If that doesn't work there are more in depth things you can do.

  • Too many errors after upgrading the firmware to 1.0.3.10 on Cisco RV180W wireless router

    My company purchased one Cisco RV180W wireless router few days ago and it worked normal with default firmware version of 1.0.0.30. Today I upgraded the firmware to version 1.0.3.10, the users can still access this router via wired and wireless devices, but on the dashboard I observed two major problems, one is the CPU utilization always shows 100%, another is the more and more errors appearing, on the Syslog Summary panel "Error" log has been up to 625 and is still increasing, there is one message repeatedly displaying in the log, see in below:
    Wed Nov 13 13:55:25 2013(GMT+0800) [rv180w][System][PLATFORM] /pfrm2.0/bin/bwLimitConfig /tmp/system.db 18 dot11STA 100 failed. status=-1
    Who can tell me what does this error message mean and how to elinate this error message ?  also how to deal with 100% CPU utilization ?
    Thanks.

    Hello,
    i have been looking at different VPN routers over the last few weeks and i was very close to buying the RV180W, but then i stumbled across many posts reffering to firmware issues, one issue is that the cpu sits at 100% useage, i just wondered if this is a bug in GUI or is the CPU actually max'd out? has anyone had any resolution into this?
    also the firmware on the emulator is a newer version than is listed on the support page, does anyone know when 1.0.3.14 will be released for download?
    when i buy a new product i like to ensure that the system is fully upto date before its put into use but i obviously dont want to add any performance issues from the ofset due to the CPU useage.
    i also have a could of questions if anyone can help
    the Ipsec VPN, will this work with the Built-in VPN client for apple devices? (New IOS7), i am unable to find a quickvpn application for apple IOS.
    is the site-to-site IPSec VPN also compatible with the Cisco Wvrs4400n router?
    thanks in advance.

  • N73 - Another Problem after upgrade the firmware t...

    Except the slow contact search problem (solved by Unplug the battery), I still suffered from some application install problems.
    1. Whenever I restart the phone, a message 'Installing' always poped up, and the phone not responding for around 2-3 minutes. And then an error message 'Unable to complete ....' prompted.
    2. The K-Mobile Client application losted after upgrade, and I tried to reinstall it , but resulted error by 'File corrupted'

    Usually that annoying installation process in the beginning can be removed by deleting that installation file in MMC>\Private\10202dce . Most of them does not have the real title of the application. To delete the right one, you need to go to the application manager first and look at the title of the application that cannot be installed nor removed. Ones you know the titles, plug in ur phone to ur computer and browse MMC>\Private\10202dce , some title of the applications from the application manager should be listed there. Delete whatever you find is listed "not installed" in application manager (app cannot be installed or removed), but first make sure to make a backup of it somehow just in case you make an error. After you delete the file/files restart ur phone. The annoying installation process should not appear anymore. Note that by just removing that file may not fully remove the files it created. For advice, if you install applications in ur phone make sure you have backup of them stored in ur computer so that if the installed applications in ur phone stops working properly all you need to do is to reinstall using the original/backup sis files.
    - Is this a Signature? -

  • Choppy video streaming after upgrading E4200 firmware to ver. 1.0.03

    Video streaming was fine until I upgraded the firmware. Is it possible to downgrade the firmware?

    You mentioned in your post that you upgraded the latest firmware. So after upgrading the firmware did you reset the router? It is recommended to reset the router after firmware upgrade.  Steps to reset the router:
    Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. After this process reconfigure the router. Power light should blink when you perform the reset process.
    After the process reconfigure the router as per the ISP setup.. Then try to do the following steps:
    A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
              1] Open the software and go to the option which says "Router Settings"
              2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
             3] Lower the MTU (Maximum Transmission Unit) from 1500 to 1400 or less (usually found on your router's main/ basic setup page)
             4] Then go to the Wireless tab, keep network mode as mixed,
     For Channel Settings of 2.4 GHz you can make Channel Width to 20 MHz only and Channel to 6, 9, 11..
     For Channel Settings of 5 GHz you can make Channel Width to 20 MHz only and Channel to 40 or 161...
    B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.

  • MSI DR4-A,How do I upgrade the firmware? (How do I flash?)

    I can't use my MSI DR4-A for anything now since i dont know how to upgrade the firmware (flash) can somebody please explain how to flash it better then the ReadMe file the lates update came with..cause i seriously don't understand the readme neither does any of my friends..so please help me someone...

    I updated the Firmware yesterday, what I did was the following.
    Downloaded the latest (2.50) firmware from the download page, and putted all the files (DVFLASH.EXE and 250D.BIN) on a floppy.
    Went to Bootdisk.com and downloaded the win98SE OEM bootdisk (as suggested by others here) and ran the exe by using a second floppy.
    Rebooted my pc with the newly created bootdisk in the floppy drive.
    After a while you'll see the prompt.
    Replace the bootdisk with the disk where DVFLASH.EXE and 250D.BIN is on and make sure the promt says A:\ (assuming this is your floppy drive).
    Then type DVFLASH 250D.BIN
    (also assuming the version is 250D.bin, which it is now atm).

  • After upgrading the new operating system, it seems some useful features no longer work such as when typing a message the text anticipates the next word and when trying to delete individual messages from a contact, you can no longer tap and hold to select

    After upgrading the new operating system on my Droid Razr M it seems some useful features no longer work such as when typing a message the text anticipates the next word and when trying to delete individual messages from a contact, you can no longer tap and hold to select multiple message you have to delete them individually or the entire thread. Is there a way to get these back?

    Well, that's kind of embarrassing. And I honestly thought I paid attention to that... It works perfectly now, thank you so much!
    As expected, cdm-git also works fine since DMs only work in the root mode as of now.
    Just for the record, both type commands output "/usr/bin/startx" and pacman -Q gives "systemd 215-4".
    Last edited by looki (2014-08-23 13:04:49)

  • CS5 can't preview the fonts image after upgrade the OS X 10.10.1

    My CS5 can't preview the fonts image after upgrade the OS X 10.10.1,
    Wanna try to reinstall the AI but my disc read error. Anyone has this problem or solution, Many Thanks!!

    Thanks but can't find this "system transparency" setting inside the illustrator. Search the key word doesn't work...

  • After upgrade the ipad2 to ios 5, my pages files in my ipad is missing? How can get back?

    After upgrade the ipad2 to ios 5, my pages files in my ipad is missing? How can get back?

    azwanelias wrote:
    my iphone 5s is jammed after downloading IOS 8.0.2 and now i cant use my iphone and it has the sing of itubes in RED which is wired how can i get my phone to work? and its not letting me restore on itunes of my PC
    I don't really understand your comment about "sing of tubes in RED which is wired". But if you are referring to the display of iTunes and the USB port that is an indication that you must restore your iPhone by connecting it to your computer via USB and then using iTunes on the computer to restore it.

  • I find Mail under Mavericks to be weird. Are others having this same difficulty. "Upgraded" to Mavericks last week, after updating the firmware to my WD external HD.

    I find Mail under Mavericks to be weird. Are others having this same/similar difficulty? "Upgraded" to Mavericks last week, after updating the firmware to my WD external HD.

    "Weird" needs further explanation.
    Google's highly nonstandard IMAP implementation is weird, if you're using Gmail, though Apple bent over backwards to accomodate it. Other than that, what do you mean by "weird"?

  • I just upgrade the OS X from 10.9.1 to 10.9.2. After upgrade, the help file is not available. How can I get it back?

    I just upgrade the OS X from 10.9.1 to 10.9.2. After upgrade, the help file is not available. How can I get it back?

    Look above at my original post:
    Downgrade Mavericks to Snow Leopard
      1. Boot from your Snow Leopard Installer Disc. After the installer
          loads select your language and click on the Continue
          button. When the menu bar appears select Disk Utility from the
          Utilities menu.
      2. After DU loads select your hard drive (this is the entry with the
          mfgr.'s ID and size) from the left side list. Note the SMART status
          of the drive in DU's status area.  If it does not say "Verified" then
          the drive is failing or has failed and will need replacing.  SMART
          info will not be reported  on external drives. Otherwise, click on
          the Partition tab in the DU main window.
      3. Under the Volume Scheme heading set the number of partitions
          from the drop down menu to one. Set the format type to Mac OS
          Extended (Journaled.) Click on the Options button, set the
          partition scheme to GUID then click on the OK button. Click on
          the Partition button and wait until the process has completed.
      4. Quit DU and return to the installer. Install Snow Leopard.
    This will erase the whole drive so be sure to backup your files if you don't have a backup already. If you have performed a TM backup using Lion be aware that you cannot restore from that backup in Snow Leopard (see below.) I suggest you make a separate backup using Carbon Copy Cloner.
    If you have Snow Leopard Time Machine backups made while on Snow Leopard, then you may do a full system restore per #14 in Time Machine - Frequently Asked Questions.  If you have subsequent backups from Lion, you can restore newer items selectively, via the "Star Wars" display, per #15 there, but be careful; some Snow Leopard apps may not work with the Lion/Mountain Lion files.

  • Here is my problem: "To open "Adobe Photoshop CS5.1" you need to install the legacy Java SE 6 RUNTIME" after upgrading iMac to Yosemite, can anybody help?

    Here is my problem: "To open "Adobe Photoshop CS5.1" you need to install the legacy Java SE 6 RUNTIME" after upgrading iMac to Yosemite, can anybody help?

    This answer may be somewhat late, but just in case other have the same issues, I went to site listed below and it solved the problem.  No need to reinstall CS5 product.  I hope this works for you.
    http://support.apple.com/kb/DL1572

  • I cannot download or updates any apps after upgrading the newest ios .. it show offers In-Apps Purchase... anybody can help me ?

    i cannot download or updates any apps after upgrading the newest ios .. it show offers In-Apps Purchase... anybody can help me ?

    This is happening to me too. I'm looking for anyway to fix this its getting very annoying not being able to update apps.

  • After updating the firmware on IOS7 I can not activate my iphone 4.

    After updating the firmware on IOS7 I can not activate my iphone 4. Itunes says "Unlock the iPhone on this ***** @ *******. ru impossible"

    ITunes says:
    At the moment the iPhone is tied to the Apple ID (i ***** @ y *****. Ru). Sign in with Apple ID, which is used to configure this iPhone.
    Unlock iPhone on this I ***** @ ya *****. Ru impossible.

  • I can not activate my iphone 4 after installing the firmware ios 7, can not remember the password apple id, a check box is all

    I can not activate my iphone 4 after installing the firmware ios 7, can not remember the password apple id, a check box are all available, please look into this matter
    serial number TP113FG5A4S, imei 012657000548662

    Copied from my initial post:
    Then you'll NEVER be able to re-activate the phone. This is called Activation Lock & there is no way around it if you don't know that info.
    You can try & recover the ID here:
    https://iforgot.apple.com/appleid

Maybe you are looking for