After upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T to the latest release the ASA-SM module is not recognized

after upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T to the latest release the ASA-SM module is not recognized it is disabled. the FPD
is not recognized any more. reverted back to previous ios with no luck

Duplicate post.
Being discussed actively in this thread.

Similar Messages

After upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T ASA-SM is disabled

after upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T to the latest release the ASA-SM module is not recognized it is disabled. the FPD
is not recognized any more. reverted back to previous ios with no luck

What IOS are you running on your Supervisor 2T? As long as it's 15.0(1)SY1 or later you should be OK. (Reference).
If it's not working with that I'd try reload of the ASA SM module (from IOS cli - e.g. "hw-module <module#> reset" and, failing that, "no power-enable module <module#>" followed by "power-enable module <module#>) while the new Supervisor is installed. Watch the log for relevant messages during that process.

How to remove the WiSM2 from the Catalyst 6500 series switch?

Hello, can you explain to me how to safely remove the WiSM2 from the Catalyst 6500 series switch?
According to the documentation "Catalyst 6500 Series Wireless Services Module 2 Installation and Verification Note":
To remove the WiSM2, perform these steps:
Step1     Shut down the module by one of these methods:
In privileged mode from the router prompt, enter the hw-mod module mod shutdown command. NoteIf you enter this command to shut down the module, you must enter the following commands in global configuration mode to restart (power down, and then power up) the module:
Router# no power enable module modRouter# power enable module mod
If the module does not respond to any commands, press the SHUTDOWN button located on the front panel of the module.
Step2     Verify that the WiSM2 shuts down. Do not remove the module from the switch until the POWER LEDis off.
But, in the case of Step1 (1st methods) I do not see a option "shutdown" in the command "hw-mod module 3"...
All I prompted to enter is:
c6500#hw-module module 3 ?
boot           Specify boot options for the module through Power Management Bus control register
reset          Reset specified component
simulate Simulate options for the module
Is it hidden options? IOS version of c6500 is 12.2(33)SXJ1
In the case of Step2 (2nd methods) there is not any button on the front panel of the module?
And yet, it is better to remove the module configuration manually or use the command module clear-config prior to removing the module?

Good catch.
Which one is true, will get back to you on this if i've something soon.
http://www.cisco.com/en/US/docs/wireless/module/wism2/installation/note/WiSM_2.html#wp34727
The above link is procedure to remove wism2. This procedure doesn’t look like wism2 is hot swapable.
http://www.cisco.com/en/US/docs/wireless/module/wism2/installation/note/WiSM_2.html#wp34621
All modules, including the supervisor engine (if you have redundant supervisor engines), support hot swapping. You can add, replace, or remove modules without interrupting the system power or causing other software or interfaces to shut down. For more information about hot-swapping modules, see the Catalyst 6500 Series Switch Module Installation Guide.

Installing New network card on a Cisco Catalyst 6500 VSS mode

Hi All.
I need to install a new network card on Cisco Catalyst 6500 VSS mode, I need to follow any special procedures or is it only insert the new card and the Catalyst automatically recognizes the card?
Thank you So mucho.

Hi,
Just insert the blade and the switch should recognize it. For the 6500 series the blades are hot swap able.
HTH

Password reset on a Cisco Catalyst 3550 series

We have a Cisco Catalyst 3550 series, and we don't have the password to gain access to the switch through a web browser. My question is if I reset the password using Hyper-terminal, does changing the password affect any vlan or fiber optic settings that I should know about. Or does resetting the password changes our switch to factory settings?

Hi,
The password recovery procedure for your switch is described in this document:
http://www.cisco.com/c/en/us/support/docs/switches/catalyst-2950-series-switches/12040-pswdrec-2900xl.html
If you follow the instructions in the document exactly, you will retain the original configuration - you just rename the configuration file so that it is not loaded when the switch boots up. However, you will still be able to display it after the switch boots up using the more flash:config.old . Eventually, you can even load it into running-config using copy flash:config.old running-config command. At that point, the old passwords will be brought back but because you already are in the privileged EXEC mode, you can change them and save the updated configuration.
VLANs should not be affected as long as you do not delete the vlan.dat file located in FLASH. Fiber optic ports should not be affected as long as you are using original Cisco GBICs. If you're using 3rd party GBICs, it may be necessary to enter the service unsupported-transceiver hidden command in the global configuration mode before they get recognized.
Good luck!
Best regards,
Peter

Why missing personal hotspot in my iphone 4s after upgrade ios 7 ?

why missing personal hotspot in my iphone 4s after upgrade ios 7 ?

I'm having the same issue (iOS 7.0.3 on 5s).
Had Sprint add Wi-Fi Hot Spot to my account today, went to set it up, and there's nothing in Settings for "Personal Hot Spot." Apparently it should appear underneath "Cellular" but it's just not there.
Resetting network settings didn't help. And Sprint doesn't know why it's not there either.

After upgrade ios 8.1 settings notice problem

Hello
After upgrading ios 8.1 my "settings" app still continues tu show 1 notice but when I open settings I see nothing waiting for, ios 8.1 is well updated in the general section...
It's just a problem on the icon screen.
Anyone else facing this issue ?
running iphone 5s

I have the same issue here… cannot erase the badge from the definition icon app.

Connection of LC/APC fiber patch cords to Cisco Catalyst 6500 $ Cisco Access 3750 Switches

I have an LC/APC fiber patch cord infrastructure and I want to connect it to Cisco Catalyst 6500 & Cisco Access 3750 Switches. what type of transceiver should be used?
I read a note on Cisco website stating the following for Cisco SFP+ transceivers:
Note: "Only connections with patch cords with PC or UPC connectors are supported. Patch cords with APC connectors are not supported. All cables and cable assemblies used must be compliant with the standards specified in the standards section"

Thank you, but my question is that I have a single mode fiber patch cord with LC/APC connector while cisco stating a note that only use LC/PC or LC/UPC type of connectors with SFP+ transceiver.
So what type of transceiver should I use to connect LC/APC patch cord to cisco switches? Is there another type or SFP+ still can be used?

Cisco Catalyst 6500 version 12.2(33)SXI13 configured as DHCP server for a VLAN responds to Windows 7 client with status code NOA

Can anyone help figure out why the Catalyst 6509 is not able to assign an IPv6 address? Thank you.
Cisco Catalyst 6500 version 12.2(33)SXI13 configured as DHCP server for a VLAN responds to Windows 7 client with status code NOADDRS-AVAIL(2). My configuration on the 6500 for the DHCPv6 server is:
ipv6 dhcp database disk0://DHCPV6-DB
ipv6 dhcp pool VLAN206IPV6
prefix-delegation pool VLAN206IPV6-POOL
dns-server 2620:B700:0:1001::53
domain-name global.bio.com
ipv6 local pool VLAN206IPV6-POOL 2620:B700:0:12C7::/65 65
interface Vlan206
description *** IPv6 Subnet ***
ip address 10.2.104.2 255.255.255.0
ipv6 address 2620:B700:0:12C7::2/64
ipv6 nd prefix 2620:B700:0:12C7::/64 14400 14400 no-autoconfig
ipv6 nd managed-config-flag
ipv6 dhcp server VLAN206IPV6
standby version 2
standby 0 ip 10.2.104.1
standby 0 preempt
standby 6 ipv6 2620:B700:0:12C7::1/64
standby 6 preempt
I'm getting a result from my debug as follows:
Apr 10 16:28:02.873 PDT: %LINK-3-UPDOWN: Interface GigabitEthernet2/2, changed state to up
Apr 10 16:28:02.873 PDT: %LINK-SP-3-UPDOWN: Interface GigabitEthernet2/2, changed state to up
Apr 10 16:28:02.877 PDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/2, changed state to up
Apr 10 16:28:03.861 PDT: IPv6 DHCP: Received SOLICIT from FE80::5D5E:7EBD:CDBF:2519 on Vlan206
Apr 10 16:28:03.861 PDT: IPv6 DHCP: detailed packet contents
Apr 10 16:28:03.861 PDT: src FE80::5D5E:7EBD:CDBF:2519 (Vlan206)
Apr 10 16:28:03.861 PDT: dst FF02::1:2
Apr 10 16:28:03.861 PDT: type SOLICIT(1), xid 8277025
Apr 10 16:28:03.861 PDT: option ELAPSED-TIME(8), len 2
Apr 10 16:28:03.861 PDT: elapsed-time 101
Apr 10 16:28:03.861 PDT: option CLIENTID(1), len 14
Apr 10 16:28:03.861 PDT: 00010001195FD895F01FAF10689E
Apr 10 16:28:03.861 PDT: option IA-NA(3), len 12
Apr 10 16:28:03.861 PDT: IAID 0x0FF01FAF, T1 0, T2 0
Apr 10 16:28:03.861 PDT: option UNKNOWN(39), len 32
Apr 10 16:28:03.861 PDT: option VENDOR-CLASS(16), len 14
Apr 10 16:28:03.861 PDT: option ORO(6), len 8
Apr 10 16:28:03.861 PDT: DOMAIN-LIST,DNS-SERVERS,VENDOR-OPTS,UNKNOWN
Apr 10 16:28:03.861 PDT: IPv6 DHCP: Option IA-NA(3) is not supported yet
Apr 10 16:28:03.861 PDT: IPv6 DHCP: Sending ADVERTISE to FE80::5D5E:7EBD:CDBF:2519 on Vlan206
Apr 10 16:28:03.861 PDT: IPv6 DHCP: detailed packet contents
Apr 10 16:28:03.861 PDT: src FE80::21D:E6FF:FEE4:4400
Apr 10 16:28:03.861 PDT: dst FE80::5D5E:7EBD:CDBF:2519 (Vlan206)
Apr 10 16:28:03.861 PDT: type ADVERTISE(2), xid 8277025
Apr 10 16:28:03.861 PDT: option SERVERID(2), len 10
Apr 10 16:28:03.865 PDT: 00030001001DE6E44400
Apr 10 16:28:03.865 PDT: option CLIENTID(1), len 14
Apr 10 16:28:03.865 PDT: 00010001195FD895F01FAF10689E
Apr 10 16:28:03.865 PDT: option STATUS-CODE(13), len 15
Apr 10 16:28:03.865 PDT: status code NOADDRS-AVAIL(2)
Apr 10 16:28:03.865 PDT: status message: NOADDRS-AVAIL

Hello,
maybe hitting the following bug.
Pv6 Address Assignment Support for IPv6 DHCP Server
CSCse81385
Hope this helps

After upgrading iOS to 7.0.4, I could not transfer:pdf files from email to ibooks ???

Help anyone ???
After upgrading iOS to 7.0.4, I could not tranfer pdf files from email to ibooks.
Previously, i would see a message asking for tranfering my word doc to pdf file and pdf file to store in ibooks...

You need to use the forward box (box with an upward arrow).
This link will tell you what to do: http://support.apple.com/kb/ht4227

How's to salute my problem. My ipad after upgrade ios 7 forget the password

How's to salute my problem
Ipad after upgrade ios 7 forget the password

How's to salute my problem
Ipad after upgrade ios 7 forget the password

After upgrading iOS 7 on my iPhone 5, the wifi is not working . It cannot detect any wifi nor am I able to enable wifi under settings. Is there a way for me to fix this?

After upgrading iOS 7 on my iPhone 5, the wifi is not working . It cannot detect any wifi nor am I able to enable wifi under settings. Is there a way for me to fix this?

Hi samer almasri,
If you are having issues with enabling Wifi on your iPhone you may want to try a couple of things to troubleshoot. First of all I would quit all open applications on the phone and try again. See this previous thread for how -
How do I close apps on my iPhone with iOS 7?
https://discussions.apple.com/thread/5581063
Next, I would try restarting the iPhone -
Turn your iOS device off and on (restart) and reset
http://support.apple.com/kb/HT1430
If the issue is still present, you may want to restore the iPhone as a new device -
iOS: How to back up your data and set up your device as a new device
http://support.apple.com/kb/HT4137
Thanks for using Apple Support Communities.
Best,
Brett L

HT1688 Hello, I have iphone 4. After upgrade ios 7.0.2 lost vibro. Please, can you help me?

Hello, I have iphone 4. After upgrade ios 7.0.2 lost vibro. Please, can you help me?

RichardRicardo wrote:
I upgraded to IOS 7.0.4 and the iPhone now is on The Activation screen i bought this iphone as USED... and i didn't know the apple id.
Sorry... But... The Apple ID and Password that was Originally used to Activate the iDevice is required.
If you cannot get this information from the seller
Removing a device from a previous owner’s account
You need to return the Device for a refund, as you will not be able to re-activate it.
There is No Workaroud for Activation Lock.

I can not use ipad smart cover after upgrade ios 7.

I can not use ipad smart cover after upgrade ios 7. It makes reboot again again...if i cover up ipad with smart cover. i never had this problem before. please fix this bug!!!!

Change your iPod DNS to 8.8.8.8
That should work. Cheers

CSM - does it support ACLs on a Cisco Catalyst 6500

Hi,
Does anyone know if CSM Enterprise Standard can be used to manage ACLs (standard and extended) on a Catalyst 6500?
Regards,
Piaras

Hi,
Just insert the blade and the switch should recognize it. For the 6500 series the blades are hot swap able.
HTH

After upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T to the latest release the ASA-SM module is not recognized

Similar Messages

Maybe you are looking for