After upgrading to 10.6.7 NAT doesn´t start

I´m doing NAT with usb ethernet and the ethernet port from a mac mini server, everything was ok until i updated to 10.6.7 any ideas? been looking around for some solutions but none has worked.

Hi,
Try to stop NAT, than start Setup Gateway Assistant again, may be help.
Note: you should be sure your firewall is in correct setup. My NAT some time stop and can not start again because of my firewall "open" much ports than nessesary.

Similar Messages

HT5502 AFTER UPGRADING TOMOUNTAIN LION SAFARI 6.0 DOESN"T WORK HOW CAN I REPLACE IT OR UPGRADE IT?

AFTER UPGRADING TOMOUNTAIN LION SAFARI 6.0 DOESN"T WORK HOW CAN I REPLACE IT OR UPGRADE IT?

An answer will require more specific information of the problems you are experiencing Mpittas2.
In general, if you installed any third party anti-virus utilities, get rid of them. They can cause problems like this.
There is no need to post your question multiple times. If you don't get an answer right away give it some time, a few hours at least, and please deselect your caps lock key. This will increase the likelihood of receiving competent assistance.
Thanks!

After upgrade to yosemite my macbook air doesn't connect to iPhone 4s(version8.1).

after upgrade to yosemite my macbook air doesn't connect to iPhone 4s(version8.1) .it did connect once and thats it...theywork now as two different mac products as before upgrade. that advantage of connecting the mac products after upgrading to yosemite has not worked.

Hi netaanya,
Welcome to the Apple Support Communities!
Your iPhone 4s does work with Continuity, but only phone calls. Please refer to the attached article for more information.
Connect your iPhone, iPad, iPod touch, and Mac using Continuity - Apple Support
Handoff is supported by the following iOS devices and requires iOS 8. Instant Hotspot requires one of these iPhone or iPad devices with cellular connectivity and iOS 8.1. Instant Hotspot also requires Personal Hotspot service through your carrier.
Phone 5 or later
iPhone 4s (sharing iPhone calls only)
iPad (4th generation), iPad Air, iPad Air 2
iPad mini, iPad mini with Retina display, iPad mini 3
iPod touch (5th generation)
Cheers,
Joe

After upgrade iphone 4 ios 6.01 doesn't work, after upgrade iphone 4 ios 6.01 doesn't work

after upgrade iphone 4 ios 6.01 doesn't work
does anybody have an idea what can i do plsss help mee

i just upgraded it to 6.0.1 and the process from itunes is done sucessfully and when it should normaly switched it is blocked it shows only the pic of apple...

After upgrading to Aperture 3.4 it doesn't open anymore.

After upgrading to Aperture 3.4 it doesn't open anymore. Every listed suggestion in forums did not help.
After repairing till 99% Aperture closed. It happened with all my libraries, small and great. All of them can be opened in iPhoto.
After placing aperture.app to the trash can and putting it back to programs again, after a restart, I even couldn't find in preferences com.apple.aperture.plist file anymore. Apple please help!

After placing aperture.app to the trash can and putting it back to programs again,
How did you put it back to programs? The idea is to make a complete reinstall
The problem is:
There is a problem with the Aperture installer. In some cases the installation is not complete, if you update on top of a recent version.
For most posters here (there must be 20 and more discussions by now) it helped to reinstall Aperture after removing the Application from the Applications Folder and the reinstalling again.
If you installed Apperture initially from the boxed retail version, reinstall from the CD/DVD.
If you installed from the AppStore, download again from the AppStore.
If you unlocked the Trial or bought online previous to the AppStore, use the saved installer or download the Trial again.
http://appldnld.apple.com.edgesuite.net/content.info.apple.com/Aperture/061-8328 .20101020.AprE3/ApertureTrial3.1.dmg
Upgrade immediately after installing the previous version; you cannot open your current library with the previous version.
Regards
Léonie
Just for the record:
To remove the preferences:
The Preferences are in your User Library, Preferences folder:
The User Library is hidden by default. You can reveal it from the Finder's "GO" menu:
Finder > Go, then hold down the options ⌥ key, until the Library appears in the drop-down menu, select it and open the Library folder. Then go to the "Preferences" sub folder and remove the file
your Home Folder/Library/Preferences/com.apple.Aperture.plist.
But I'd try to reinstall first - removing the preferences will only be a temporary fix, and the crashing may occur again, if you do not fix the broken Aperture installation.

After Upgrading to 10.6.8 my aperture app starts but hangs trying to read the Lib. I removed the old lib and start with new. but still have the problem. 10.6.8 also made my Shark FX7 do the same thing. Any Ideas? Thanks

After Upgrading to 10.6.8 my aperture app starts but hangs trying to read the Lib. I removed the old lib and start with new. but still have the problem. 10.6.8 also made my Shark FX7 do the same thing. Any Ideas? Thanks

Verifying volume “Macintosh HD”
Performing live verification.
Checking Journaled HFS Plus volume.
Checking extents overflow file.
Checking catalog file.
Checking multi-linked files.
Checking catalog hierarchy.
Checking extended attributes file.
Checking volume bitmap.
Checking volume information.
The volume Macintosh HD appears to be OK.

After upgrading to Snow Leopard, Canon MX870 doesn't print text...just images

After upgrading to Snow Leopard (yes I know I'm slow to upgrade) my Canon MX870 isn't printing text. It is printing images but the quality if horrendous because it's not printing the black ink.
Here's what I've done so far
Installed the latest drivers for Snow Leopard from Canon
Cleaned the heads of the printer
Added new ink to all cartridges
Run printing tests (nozzle print patterns)...all good
Reset my printers in the Print Fax Preferences and added in the printer again
Numerous restarts
Now I'm at a loss for what else to do. Does anyone have any other suggestions?
BTW, printer is connected via USB not wireless.

OK well I can see now that all of my files are present on the hard drive (mybook) only they are not showing up in aperture. It seems that there has been some sort of communication breakdown between the two.
As I said several files are missing and or corrupt in my aperture library. I'm wondering if there is a way to rebuild the library without using the vault technique? Does this make sense to anyone?
I was able to go into finder - mybook - aperture library - show contents and see that all my raw files at least are there. Now I just need to get aperture to recognize them.
Any help is greatly appreciated!
Chris

Personal hotspot worked in Dec, after upgrading to IOS 6.1, it doesn't

When I was at our cabin in the 'wilds' of MT, I was able to use my iPhone 5 as a personal hotspot to connect my iPad and use it to read mail, news, search the internet, etc. After upgrading my phone to IOS 6.1, when I go to turn on the personal hotspot, it says I need to turn on both Wi-Fi and Bluetooth, or use a USB port. I didn't need to do this before the upgrade, and when I'm in MT, there is no wi-fi. What happened? And, yes, I do have a carrier that supports this, Verizon. I'm on their Share Plan.
Any fixes/suggestions for this would be greatly appreciated.
Susan n

Also, I was able to connect using WLAN, and now I no longer have that option when turning on the Personal hotspot. All that shows up is Wi-fi, bluetooth, or USB. Where did the WLAN go?
thanks!!! Susan

After installation of Solaris 10 - CDE login doesn't start

I have installed Solaris 10 on Sparc Machine but the CDE login doesn't start .
I received the message :
Suspendind Desktop Login...
If currently logged out, press [enter] for a console login promt.
desktop Login will resume shortly after you exit console session.
In the file /var/dt/Xerrors I have :
fbconsole: ioctl SRIOCSREDIR: Device busy
ioctl(MSIOSRESOLUTION): Invalid argument
ddxSUNWmouse: couldn't set absolute mouse scaling resolution on /dev/mouse
Tue Sep 12 11:54:15 2006
error (pid 2490): Can not lock pid file /var/dt/Xpid, another Dtlogin is running (pid 873)
I set the resolution of monitor for one supported :
fbconfig -res 1280x1024x60
But always I obtain the same thing,
Can someone help me ?
May thanks in advance,
Luz

I don't know if it helps. But I had problems with the x-server not starting (didn't even get a gui login just command line) re-setting the network properties seemed to fix it, looks like anything dodgy in the network config stuffs up the start up proceedure.

After upgrade to 12.1.3, ICM is not started successfully

Hi experts,
After upgrade to 12.1.3, a weird problem related to Internal Concurrent Manager(ICM) occurred and i can't fix
it by searching this forum.
Normally when i start EBS apps tier, i use script adcmctl.sh to start ICM and it exits with status 0 which means
it's ok. However when i try to submit a concurrent request, it prompts that "no active manager". So i run the command
./adcmctl.sh start apps/pwdThis command also exits with status 0 and ICM is brought up successfully. Now here is my question, why ICM is NOT started
successfully when i try to start the apps tier while it succeeds at this time. Under these two circumstances, the same script
is applied.
Thanks,
Ted

Ted xu wrote:
hi,
I see there is no error message in those CM log files. Only thing that is suspicious is found in VIS_1009.mgr(VIS is my ORACLE SID):
Found dead process: spid=(32609), cpid=(2033664), Service Instance=(1095)
Found dead process: spid=(32600), cpid=(2033661), Service Instance=(2158)
Found dead process: spid=(32595), cpid=(2033660), Service Instance=(31528)
Please see these docs.
Concurrent Managers Will Not Start ORACLE error 60 in insert_fcp [ID 1256084.1]
Why Are Dead Process Found In The Standard Manager Log File? [ID 246584.1]
Thanks,
Hussein

After upgrade to IOS 4 screen rotation doesn't work.

I just upgraded my iPhone 3Gs to IOS 4 and the screen doesn't rotate with any apps when I turn the iphone 90 degrees to the horizontal. Any fixes anyone knows of? Thanks

Update on my particular issue:
When I open an app that responds to screen rotation (photos, safari), hold my phone on its side and then shake up down very hard, then the screen will rotate. If I tip it back up into portrait orientation the screen still doesn't rotate. But if I shake the phone hard in that orientation, the screen will rotate.
So maybe I've got hardware issues.

After upgrading to Lion my internet connection doesn't work

Hey folks,
     MacPro 2010, wired connection through Verizon FiOS, upgraded to Lion (via App Store) back in July, but now my wife says she can't get on the Interent
on her account, even though all connections are good, she has an IP, subnet, DNS are good, the ethernet settings say she is connected, but using Chrome (13.0.782.122) or Safari, just hangs on browser launch. No URL will resolve no matter what site I enter. But when I log out of her account and into mine I can connect using the same Chrome browser just fine.
     The only thing I can come up with is Chrome has had issues for quite some time on Snow Leopard and Lion when trying to update. About Chrome will display there is a new version and hitting the Install button will result in a "Update Server not available Error Code: 12". Any workaround by the Chrome Blog was not helpful, and uninstalling and reinstalling the program would sometimes work. But every so often when I would manually check About Chrome it would mysteriously be updated all by itself, and I was fine. Eventually though, every so often I would check and it would say there's a new version and I would get the infamous error. I could never seem to update the program myself. I would have to wait until it did it on its own?
I don't know if fooling around with Chrome's insides (using AppTrap to get rid of Chrome, manually deleting Preferences.js files, etc) corrupted something on my wifes account, which is a limited account and had some Parental Controls enabled - although she had Allow Unrestricted Access to Internet Sites checked off. I DID, however, have the Apps section restricted at some level, and I believe certain Chrome features were blocked ( like google updater), because while logged into her account, chrome would pop up: "you don't have access to GoogleUpdater...etc" and another one named   "xml or xmd" something or other, I can't remember exactly so I apologize. But while troubleshooting the no internet issue, I hit "Always Allow" for both messages, put in my password and she still couldn't get on the web, even when I turned off Parental Controls altogether. I couldn't even do a Software Update, it would just not move.
I even opened a Terminal window and Pinged www.google.com and was receiving replys at a steady rate, so I don't know what else to try. Safari is also exhibiting this same behavior, so I'm thinking its a common issue with both browsers since both use Webkit? I could be wrong obviously...
I'm at a loss as to what it could be or what to test out. Any help would be welcomed.
Philip

I had this problem on SL and on Lion as well, and it occures for WiFi and Ethernet connections.
In fact the internet connection was not broken as I could ping the destination usin the IP (not DNS name).
In this case the problem was related to mDNSResponder task which handles all dns queries.
It was the most frequent problem in my day to day work with SL and now Lion. It was never fixed by any patch from Apple. I tried almost all voodoo including fresh install, all possible config changes - no solution.
The only version with no problems related to network was 10.5.8. All the other versions had issues of different kind (WiFi instability (lost signal), DNS problems (for wireless and wired connection) sometimes associated with machine sleep and wake up and sometimes with no reason.
QUESTION: Is your problem independent of the access point / router you connect to.
I must say networking was (and still is) the weakest part, besides the other OS X weaknesses I experienced during 4 years of OS X usage.
No problems in the same network with Linux or Windows beeing ran natively on my iMac So hardware is OK.
Software is of poor quality. Not much more to say in this matter.
I found a very interesting article dated 1996 about programming which I think is still valid.
Link to the article: http://www.fastcompany.com/magazine/06/writestuff.html
Below the fragment (with some connection to Apple)
Software is everything. It also s***s.
"It's like pre-Sumerian civilization," says Brad Cox, who wrote the software for Steve Jobs NeXT computer and is a professor at George Mason University. "The way we build software is in the hunter-gatherer stage."

After upgrading to ios 5 Open In doesn't work with large files

With ios 4 I used to be able to download large video files >1 gb (avi, wmv, etc) using Downloads app and then Open In AV Player app. Now it doesn't work. What's the deal Apple?

Same problem here.
And found several topics seen on other sites, like: http://forums.macrumors.com/showthread.php?t=1261864
this seems to be a real bug when reading the topics there. First thought it was related to the apps I was using, but sems to be the iOS5..
hope this will be fixed in the next release.

After upgrading to 10.6.3 iTunes doesn't recognize my iPhone or iPad

I was running 10.4.11 and things were working. Just got an iPad, which wouldn't work on 10.4.11 so I upgraded to 10.6.3. Now when I plug in the iPhone to the iMac the only thing that launches is iPhoto. If I open iTunes it does not show the iphone. And plugging in the iPad gets no results either.
What do I need to do? All help appreciated.

Embarrassing...I hadn't upgraded the iTunes software.

Hi, after upgrade to 7.0.5, Facebook doesn't show up in Notification Center...

Reinstall, restart, nor wipe didn't help Notification Center settings just ignore like it's been never installed. Therefore it doesn't push notification or lock screen, nor beep or do anything else. Even doesn't show any update on FB icon. I have the latest Facebook client installed and my iPhone is 5 days old. Anyone has any advice, please?

Just a heads up – mine came back online this morning and can verify that they're working.
I'm guessing it was FB's servers, and some minion has flicked the switch and set everything right again.
I closed all my apps, turned off my phone. Upon turning it on and loading FB – the "Allow Push Notifications" dialog popped straight up.
Hope this resolves your issue!
UPDATE: You beat me to it! Ha.

After upgrading to 10.6.7 NAT doesn´t start

Similar Messages

Maybe you are looking for