After waking rMBP from sleep and typing password, rMBP goes back to sleep after a few seconds and won't wake for about 7-8 seconds.

Absolutely embarrassing. What is going on here? When will we see a fix?

This happens rarely but consistently! I't seems to happen about 5% of the time waking from sleep. It MAY be more prone to happen if I had been moving with it in my bag, but it can happen at any waking time after any duration of sleep.

Similar Messages

Hello, I have a macbook pro late 2011 15 inch with 4 gb ram. My macbook runs extremely slow when logging in after waking up from sleep, locking up and I am unable to use the keyboard. Is there a fix?

My macbook runs extremely slow when logging in after waking up from sleep, locking up and I am unable to use the keyboard. Furthermore, when just using safari to watch streaming television, my computer gets really slow, and locks up, and the dock appears blank and I sit here frustrated. Anytime i wake up my computer, my keys don't respond and I've waited at most 3 minutes untill i can type in my password. Even sometimes when i type in my password and hit enter, it takes forever to open up my mac. I have barely used any storage in my macbook, since i only use it for college, and I have run clamscan wiht no viruses showing... Any ideas?

when just using safari to watch streaming television, my computer gets really slow, and locks up, and the dock appears blank
Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, or by a peripheral device.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output andWi-Fi on certain iMacs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

Problem waking up from sleep after upgrading to Maverics

My Mac mini have a problem waking up from sleep.
I can see and move the mousepointer but the rest is black.
This problem started after upgrading to Maverics.
I have to restart to get back on track...
I have a 2.3Ghz Core i5 earley 2012 with 8GB RAM and a Samsung Syncmaster 226BW.

That resembles > Login window partially appears, cursor movement redraws screen
Try the "Additional Information" steps in the article.

Ethernet interface disappears after waking up from sleep

Hi guys,
I've been trying to debug a networking problem without any luck and I think it's about time I ask the forum for help.
My ethernet interface no longer works after I wake up my computer from sleep. I have no idea why.
Before sleep:
# ls /sys/class/net
lo wlp2s0 enp3s0f2
After waking up from sleep,
ls /sys/class/net
lo wlp2s0
Here are the list of services I have running.
UNIT LOAD ACTIVE SUB DESCRIPTION
dbus.service loaded active running D-Bus System Message Bus
[email protected] loaded failed failed dhcpcd on enp3s0f2
[email protected] loaded active running Getty on tty1
[email protected] loaded active running Daemon which acts upon network cable inse
kmod-static-nodes.service loaded active exited Create list of required static device nod
[email protected]\x2dSecure.service loaded active exited Networking for netctl profile wlp2s0-Wolf
polkit.service loaded active running Authorization Manager
systemd-backlight@acpi_video0.service loaded active exited Load/Save Screen Backlight Brightness of
systemd-fsck@...\x2d38bc68d942fc.service loaded active exited File System Check on /dev/disk/by-uuid/1c
systemd-journald.service loaded active running Journal Service
systemd-logind.service loaded active running Login Service
systemd-random-seed.service loaded active exited Load/Save Random Seed
systemd-remount-fs.service loaded active exited Remount Root and Kernel File Systems
systemd-sysctl.service loaded active exited Apply Kernel Variables
systemd-tmpfiles-setup-dev.service loaded active exited Create static device nodes in /dev
systemd-tmpfiles-setup.service loaded active exited Recreate Volatile Files and Directories
systemd-udev-trigger.service loaded active exited udev Coldplug all Devices
systemd-udevd.service loaded active running udev Kernel Device Manager
systemd-update-utmp.service loaded active exited Update UTMP about System Reboot/Shutdown
systemd-user-sessions.service loaded active exited Permit User Sessions
systemd-vconsole-setup.service loaded active exited Setup Virtual Console
upower.service loaded active running Daemon for power management
[email protected] loaded active running User Manager for 1000
Furthermore, plugging in the ethernet cord after the computer has started doesn't connect to the internet, even when I have the ifplugd service running. I am forced to run:
sudo ip link set enp3s0f2 up
sudo dhcpcd enp3s0f2
However, I can't run these commands after the laptop wakes up from sleep since it no longer sees the ethernet interface.
I am thoroughly confused. Please help me.

It seems to be fixed after the kernel update. On an related note, I've switched from using dhcpcd to netctl. I've enabled netctl to automatically connect to the network using:
# systemctl enable [email protected]
# systemctl enable [email protected]
So when I check for the status of the ethernet profile, I get told that's it's inactive.
#netctl status ethernet-dhcp
netctl@ethernet\x2ddhcp.service - Networking for netctl profile ethernet-dhcp
Loaded: loaded (/usr/lib/systemd/system/[email protected]; static)
Active: inactive (dead)
Docs: man:netctl.profile(5)
But I turned off the wireless, so I must be connected to the ethernet, So how do I know which profile I'm connected to?

Certain applications will not open after restart or waking up from sleep

My Macbook Pro running 10.9.2 won't open certain applications after restarting and sometimes after waking up from sleep. Google Chrome, Logic Pro X, Adobe Photoshop and Premiere seem to be the only progams affected. Firefox and Safari both work fine as well as many other applications. It seems to only affect programs that connect to the internet.
After a period of time the issue will resolve itself; sometimes after a few minutes and other times after several days. Then, these applications suddenly begin working again. I have also been having issues with my computer's ability to wake up. My best guess is that my computer isn't "fully waking up" upon restarts or when coming out of sleep mode. Both of these issues began around the same time and could be related. I've had both problems for several months through multiple software updates.
As far as troubleshooting goes I have done the following:
Safe Boot - (all programs work but are not effective due to lack of drivers being utilized in safe mode)
RAM/PRAM reset.
Disk Utility/Repair Permissions/Verify Disk
Any help or advice would be VERY appareciated.

Robin,
It sounds like your MacBook is logging out when the computer goes to sleep if you are getting the login window, which will of course close all your programs.
In System Preferences >Security, uncheck "Log out after.....minutes of activity".
See if this stops it from doing that.

Compaq C700 - CPU fan not running after waking up from Sleep mode

Hi guys,
Waking up from Sleep mode does not start the CPU fan.
Kernel: 2.6.32-ARCH
KDE : 4.4
Let me know what other details you need.

I was having the same problem after installing mountain lion.
What i did was in Finder went to /Library/Preferences/SystemConfiguration/ and deleted all the networking plists (refer screen shot). Then restarted the Mac and in Network Preferences reconnected to my WLAN.
That solved the problem.

W510 eSATA/USB2.0 combo port does not respond after waking up from sleep mode

Has anyone tried to connect external DVD/CD player or burner to the eSATA/USB combo port and experienced very slow system performance after waking up from sleep mode? It might takes minutes to launch an application program that usually takes just few seconds. My W510 can not even restart. It will just stop at the Thinkpad logo if I tried to restart after waking up from sleep.
The funny thing is if I moved the external DVD/CD player to the USB2.0 port in the back, everything went back to normal. I don't know if this has anything to do with the fact that the combo port has something to do with eSATA.
Thanks

It seems that this problem is unique to my system. I am hoping that one of the Mac Guru's will have at least a pointer in the right direction.
Thanks.

Touchscreen stops working after waking up from sleep

Touchscreen stops working after waking up from sleep sometime it not working at all.
IT encore2 WT8-B32CNM

If you can't solve your issue and no one in the community can help, contact support to speak with a tech support agent at (800) 457-7777.
- Peter

Why does my Mac screen suddenly go dark? Sometimes it stays dark for an indefinite period after waking up from sleep.

Why does my Mac screen suddenly go dark? Sometimes it stays dark for an indefinite period after waking up from sleep. I have to open and shut the monitor screen to get it to light up again.

Might try posting in the MacBook Pro laptop forum. This is the Mac Pro desktop forum.
Also see:
OS X: When your Mac doesn't sleep or wake

Lose connection to external USB hard drive after waking up from sleep

My Mac lost connection to the external USB hard drive after waking up from sleep. I can still see the folders in the hard drive in Finders, but when I double clip a folder no file within the folder is displayed. I have to reconnect the hard drive with iMac to read its contents.
May I ask how this happens and is there a solution?
I'm using Paragon NTFS for Mac OS X to read from and write to NTFS format of USB external hard drive.
Thanks!

... I un-ticked the "put hard disks to sleep when possible" option in the Energy Saver panel in the System Preferences, and it seems the problem is solved. will have to sleep and wake up my iMac to further verify if this is the solution ...
Alternative advices are always greatly appreciated!

High power comsumption and wrong setting when waking up from sleep

See here for some more information: http://forums.lenovo.com/t5/Windows-7-RTM-Discussion/High-Power-Consumption-with-Windows-7/td-p/1668...
Settings: T400, integrated GPU,"maximum battery live" power sheme, brightness level 3, wlan on. Newest switchable graphics driver, power manager and power management drivers installed, SU4 didn't find newer drivers.
Power consumption is between 12-16W most of the time, whereas it was close to 10W on XP, from what i heard from a friend, i installed win7 on my machine right after i bought the thinkpad.
When waking up from sleep( i think hibernation as well) power consumption is abnormal, because both GPUs are activated. You have to switch to to the dedicated and back to the integrated via power manager to deactivate the ATI, which is very annoying.
Is lenovo working on these issues or are there any workaroungs already?

I've got similar problems on a T400 with hybrid graphics running Windows 7 x64 Professional, upgraded from Vista x64 Professional. I've upgraded everything to the latest (driver, bios, etc etc) using System Update.
When I boot up from cold, and switch to using batteries, the power consumption is around 8w. Very good.
Then I suspend, and resume from suspend, and the power consumption shoots up to like 20w. Horrible.
Then I manually switch to "High performance" and then back to "Energy saving", the power consumption comes back down, but to >9w, which is like 13% above the original 8w level. Acceptable, but not good.
This seems to indicate there're at least two problems with the power management aspect of T400 + Win7 x64:
First, there is the well-known problem that both internal and external graphics cards get turned on upon resume. Lenovo, please fix this problem. It's completely unacceptable to have to manually perform that switching every time one closes, and then opens the lid, or loss 60% of the battery life. And I do need to use the external GPU from time to time, so disabling it at BIOS level is not acceptable either.
Second, there is the more subtle problem that some other hardware/driver besides the graphics card makes the T400 draw an extra >1w upon resume.
I really wonder if these problems occur with T400 preinstalled with Win7 x64. If they do, shouldn't every major laptop review sites take notice of the defect and warn people. If they don't, then I do not really see why it's so hard for Lenovo to provide earlier users with the right driver/registry patch/etc to enable the correct behavior. As far as I know, these problems have not been fixed since Win7 came out.
Finally let me add that other that this, I'm extremely satisfied with my T400/Win7 system. The thermal dissipation, noise level, and durability are just top-notch. But this just makes the above mentioned problems more of a thorn in the side!

After snow upd - imac 24" c2d crashes when waking up from sleep mode

hi,
I´ve a imac 24" c2d and installed snow over working 10.5.8. everything was ok, but now if the mac is waked up from sleep, it crashes
here is the logfile:
Interval Since Last Panic Report: 3901 sec
Panics Since Last Report: 1
Anonymous UUID: BE4BB7BB-FF5F-4343-9806-47D7A9743D1A
Sat Aug 29 21:16:07 2009
panic(cpu 0 caller 0x226297): "thread_invoke: preemption_level 1, possible cause: blocking while holding a spinlock, or within interrupt context"@/SourceCache/xnu/xnu-1456.1.25/osfmk/kern/sched_prim.c:1471
Backtrace (CPU 0), Frame : Return Address (4 potential args on stack)
0x5cb53918 : 0x21acfa (0x5ce650 0x5cb5394c 0x223156 0x0)
0x5cb53968 : 0x226297 (0x5864e8 0x1 0x5864a8 0x225e89)
0x5cb539e8 : 0x22699d (0x87f401c 0x87f401c 0x5cb53a48 0x232085)
0x5cb53a58 : 0x226a2b (0x0 0x0 0x0 0x21910a)
0x5cb53a78 : 0x29c008 (0x0 0x0 0x5cb53acc 0x1)
0x5cb53b08 : 0x32e160 (0x7f5d150 0x95d7900 0x4a997e49 0x3121c3)
0x5cb53b38 : 0x34911c (0x100a8c0 0x8162c04 0x5cb53be8 0x2345ba)
0x5cb53cb8 : 0x357d77 (0x587d9f00 0x0 0x0 0x5cb53d10)
0x5cb53d48 : 0x4aeb5f (0x961a660 0x0 0x587d9f00 0x5cb53e44)
0x5cb53e08 : 0x4b4eea (0x961a660 0x5cb53e44 0x84aaa00 0x587d9f00)
0x5cb53ee8 : 0x4b52ff (0x84aaa00 0x0 0x87d81b4 0x39)
0x5cb53f78 : 0x4ed85f (0x8259d20 0x84d6b48 0x87d81b4 0x2270aa)
0x5cb53fc8 : 0x29d3fd (0x84d6b44 0x1 0x10 0x81ed9e4)
BSD process name corresponding to current thread: mDNSResponder
Mac OS version:
10A432
Kernel version:
Darwin Kernel Version 10.0.0: Fri Jul 31 22:47:34 PDT 2009; root:xnu-1456.1.25~1/RELEASE_I386
System model name: iMac7,1 (Mac-F42386C8)
System uptime in nanoseconds: 52473064073
unloaded kexts:
(none)
loaded kexts:
com.parallels.kext.prl_vnic 4.0 3844.409800 - last loaded 24033197772
com.parallels.kext.prl_netbridge 4.0 3844.409800
com.parallels.kext.prlusbconnect 4.0 3844.409800
com.parallels.kext.prlhidhook 4.0 3844.409800
com.parallels.kext.prl_hypervisor 4.0 3844.409800
com.markspace.iokit.IOMissingSyncMassStorage 199
at.obdev.nke.LittleSnitch 2.1.05
com.apple.driver.InternalModemSupport 2.6.0
com.apple.filesystems.autofs 2.1.0
com.apple.driver.AppleHWSensor 1.9.2d0
com.apple.driver.AppleHDA 1.7.4a1
com.apple.driver.AppleUpstreamUserClient 3.0.5
com.apple.driver.AppleTyMCEDriver 1.0.1d8
com.apple.kext.ATIFramebuffer 6.0.0
com.apple.DontSteal_Mac_OSX 7.0.0
com.apple.driver.AudioIPCDriver 1.1.0
com.apple.driver.AppleIRController 161
com.apple.driver.AppleIntelYonahProfile 14
com.apple.driver.AppleIntelPenrynProfile 17
com.apple.driver.AppleIntelNehalemProfile 11
com.apple.driver.AppleIntelMeromProfile 19
com.apple.driver.ACPISMCPlatformPlugin 3.4.0a20
com.apple.driver.AppleGraphicsControl 2.8.16
com.apple.driver.AppleBacklight 170.0.2
com.apple.driver.AppleLPC 1.4.6
com.apple.ATIRadeonX2000 6.0.0
com.apple.driver.AppleHIDKeyboard 1.1.5f1
com.apple.driver.CSRHIDTransitionDriver 2.2f18
com.apple.iokit.SCSITaskUserClient 2.5.0
com.apple.BootCache 31
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib 1.0.0d1
com.apple.iokit.IOAHCIBlockStorage 1.5.0
com.apple.driver.AppleUSBHub 3.7.8
com.apple.driver.AppleHPET 1.4
com.apple.driver.AppleAHCIPort 2.0.0
com.apple.driver.AppleIntelPIIXATA 2.5.0
com.apple.driver.AppleUSBEHCI 3.7.5
com.apple.iokit.AppleYukon2 3.1.14b1
com.apple.driver.AirPortBrcm43xx 410.91.20
com.apple.driver.AppleFWOHCI 4.3.4
com.apple.driver.AppleEFINVRAM 1.3.0
com.apple.driver.AppleRTC 1.3
com.apple.driver.AppleUSBUHCI 3.7.5
com.apple.driver.AppleACPIButtons 1.3
com.apple.driver.AppleSMBIOS 1.4
com.apple.driver.AppleACPIEC 1.3
com.apple.driver.AppleAPIC 1.4
com.apple.driver.AppleIntelCPUPowerManagementClient 90.0.0
com.apple.security.sandbox 0
com.apple.security.quarantine 0
com.apple.nke.applicationfirewall 2.0.11
com.apple.driver.AppleIntelCPUPowerManagement 90.0.0
com.apple.driver.AppleHDAPlatformDriver 1.7.4a1
com.apple.driver.AppleHDAHardwareConfigDriver 1.7.4a1
com.apple.driver.DspFuncLib 1.7.4a1
com.apple.driver.AppleProfileReadCounterAction 17
com.apple.iokit.IOFireWireIP 2.0.3
com.apple.driver.AppleProfileTimestampAction 10
com.apple.driver.AppleProfileThreadInfoAction 14
com.apple.driver.AppleProfileRegisterStateAction 10
com.apple.driver.AppleProfileKEventAction 10
com.apple.driver.AppleProfileCallstackAction 20
com.apple.iokit.IOSurface 73.0
com.apple.iokit.IOBluetoothSerialManager 2.2f18
com.apple.iokit.IOSerialFamily 10.0.2
com.apple.iokit.IOAudioFamily 1.7.0fc16
com.apple.kext.OSvKernDSPLib 1.3
com.apple.driver.AppleHDAController 1.7.4a1
com.apple.iokit.IOHDAFamily 1.7.4a1
com.apple.iokit.AppleProfileFamily 40
com.apple.driver.AppleSMC 3.0.1d2
com.apple.driver.IOPlatformPluginFamily 3.4.0a20
com.apple.iokit.IONDRVSupport 2.0
com.apple.kext.ATI2600Controller 6.0.0
com.apple.kext.ATISupport 6.0.0
com.apple.iokit.IOGraphicsFamily 2.0
com.apple.driver.CSRUSBBluetoothHCIController 2.2f18
com.apple.driver.AppleUSBBluetoothHCIController 2.2f18
com.apple.iokit.IOBluetoothFamily 2.2f18
com.apple.driver.AppleUSBHIDMouse 1.3.0f1
com.apple.driver.AppleHIDMouse 1.3.0f1
com.apple.iokit.IOUSBHIDDriver 3.7.5
com.apple.driver.AppleUSBMergeNub 3.7.5
com.apple.driver.AppleUSBComposite 3.7.5
com.apple.iokit.IOSCSIMultimediaCommandsDevice 2.5.0
com.apple.iokit.IOBDStorageFamily 1.6
com.apple.iokit.IODVDStorageFamily 1.6
com.apple.iokit.IOCDStorageFamily 1.6
com.apple.driver.AppleFileSystemDriver 2.0
com.apple.driver.XsanFilter 402.1
com.apple.iokit.IOATAPIProtocolTransport 2.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily 2.5.0
com.apple.iokit.IOUSBUserClient 3.7.5
com.apple.iokit.IOAHCIFamily 2.0.0
com.apple.iokit.IOATAFamily 2.5.0
com.apple.iokit.IO80211Family 300.20
com.apple.iokit.IONetworkingFamily 1.8
com.apple.iokit.IOFireWireFamily 4.1.7
com.apple.driver.AppleEFIRuntime 1.3.0
com.apple.iokit.IOUSBFamily 3.7.8
com.apple.iokit.IOHIDFamily 1.6.0
com.apple.iokit.IOSMBusFamily 1.1
com.apple.kext.AppleMatch 1.0.0d1
com.apple.security.TMSafetyNet 6
com.apple.driver.DiskImages 281
com.apple.iokit.IOStorageFamily 1.6
com.apple.driver.AppleACPIPlatform 1.3
com.apple.iokit.IOPCIFamily 2.6
com.apple.iokit.IOACPIFamily 1.3.0
Model: iMac7,1, BootROM IM71.007A.B03, 2 processors, Intel Core 2 Duo, 2.8 GHz, 4 GB, SMC 1.21f4
Graphics: ATI Radeon HD 2600 Pro, ATI,RadeonHD2600, PCIe, 256 MB
Memory Module: global_name
AirPort: spairportwireless_card_type_airportextreme (0x14E4, 0x88), Broadcom BCM43xx 1.0 (5.10.91.19)
Bluetooth: Version 2.2.0f18, 2 service, 0 devices, 1 incoming serial ports
Network Service: Ethernet, Ethernet, en0
Network Service: Parallels Shared Networking Adapter, Ethernet, en4
Network Service: Parallels Host-Only Networking Adapter, Ethernet, en5
Serial ATA Device: WDC WD5000AAKS-40YGA0, 465,76 GB
Parallel ATA Device: MATSHITADVD-R UJ-875
USB Device: Built-in iSight, 0x05ac (Apple Inc.), 0x8502, 0xfd400000
USB Device: Keyboard Hub, 0x05ac (Apple Inc.), 0x1005, 0xfd100000
USB Device: Apple Optical USB Mouse, 0x05ac (Apple Inc.), 0x0304, 0xfd130000
USB Device: Apple Keyboard, 0x05ac (Apple Inc.), 0x021e, 0xfd120000
USB Device: Hub, 0x0409 (NEC Corporation), 0x005a, 0xfa400000
USB Device: Cinergy T², 0x0ccd, 0x0038, 0xfa430000
USB Device: IR Receiver, 0x05ac (Apple Inc.), 0x8242, 0x5d100000
USB Device: Bluetooth USB Host Controller, 0x05ac (Apple Inc.), 0x8206, 0x1a100000

I'm having the same problem with a Black Macbook C2D 2.4Ghz. Installed Snow Leopard over 10.5.8 and whenever the computer sleeps, it completely hangs on wake. I've installed the system twice and the behavior is the same. Tried pulling each of the RAM sticks. No difference. Anybody else?

OSX 10.9.1 macbook pro 13 retina - wifi does not reconnect automatically when waking up from sleep mode since I have a Bluetooth apple magicmouse

Hello,
My config is OSX 10.9.1 new macbook pro 13 retina (2014).
The wifi does not reconnect automatically when waking up from sleep mode since I have a Bluetooth apple magicmouse.
It was not the case before I bought the BT mouse.
Is this problem between Wifi and bluetooth coming from the OS?
Is there a fix already available or scheduled?
Thanks

Hello alexandrefromfrance
Check the Symptom: The network connection drops unexpectedly section for steps on what to do when your MacBook Pro does not connect after waking from sleep. I have also quoted the section on troubleshooting the issue as well.
Wi-Fi: How to troubleshoot Wi-Fi connectivity
http://support.apple.com/kb/HT4628
Symptom: After restarting or waking from sleep, my computer might not connect to the Internet
After waking from sleep or starting up, your computer may not show that it is connected to a Wi-Fi network.
After start or wake, your computer may indicate that it is connected to a network, but does not connect to the Internet.
Solution
Use these steps if your computer does not automatically connect to your desired Wi-Fi network.
Check your TCP/IP settings in the Network pane of the System Preferences. Click the "Renew DHCP lease" button
Choose System Preferences from the Apple menu.
Choose Network from the View menu.
Select Wi-Fi, then click the Advanced button in the lower-left hand corner of the screen.
Click the TCP/IP tab from the top of the screen.
Click the "Renew DHCP lease" button.
Select the Wi-Fi tab and view your Preferred Networks list.
Select each network and click the minus sign to remove those networks from your Preferred Networks list.
Click OK and close the Network preferences.
Remove your stored network passwords using the Keychain Access Utility.
Open Keychain Access from /Applications/Utilities. Your window will look like this:
Remove your AirPort network passwords from the login keychain: Select the "login" keychain from the Keychain sidebar. Click the "Kind" column to order the list of keychain items by their type. Remove all entries of the kind: "AirPort network password".
Remove your AirPort network passwords from the System keychain: Select the "System" keychain from the Keychain sidebar. Click the "Kind" column to order the list of keychain items by their type. Remove all entries of the kind: "AirPort network password".  Note: The above steps will remove your Wi-Fi network passwords. If you do not know them, or if your network does not use passwords to restrict access, you should contact your network administrator.
Restart your computer.
Join your Wi-Fi network. You will need to enter your password for your network again if it requires one.
Regards,
-Norm G.

Waking up from sleep with blue screen

Waking up from sleep with blue screen
Since a few days my MBP wakes up from sleep by showing a blue screen for 30 seconds or more, instead of jumping to the login window (password needed after sleep)
I looked in the forums for blue screen but found many problems non related to this.
Any ideas?
Could it have to do with the fact that about 4 days ago I upgraded to 4.8 from 4.7?

Hi ChangeAgent,
FINDER> FILE > FIND
Use the FIND file from the Finder, not Spotlight, to find the folder called Receipts and click on this folder. Scroll down to see if you have this Security Update installed --
Security Update: 2006-008
it may be causing general problems to everyone.
I have only seen this BLUE SCREEN since I installed this security update.
It's the very latest one.
The Blue Screen is not my only problem:
I have had two system crashes (computer waking up with DARWIN window error, fixed when I re-booted).
Scrolling has slowed down in some applications.
The update in Microsoft Office vX was reverted, yesterday I received a message that said: Welcome to Microsoft Office (how can it welcome me when I have been using it every day for the past 15 years?)
Dashboard: It takes 3 minutes for the Widgets to upload.
SOMETHING is not right with this Security Update. Apple, please HELP!
iBook 14 G4 Mac OS X (10.4.8)

Laptop waking up from sleep, then turning off

After I installed snow leapord the only major problem I came across was my computer waking up from sleep mode. Once it wakes up, its on for about 2 minutes then everything turns off. The weird thing is it looks like it goes back to sleep because the macbook pro light where you open the lid is still pulsing, like its trying to wake up. The keyboard lights are off, screen is off. I can hear the disk spinning also. Once it woke up to freeze and go back to sleep.
Is anyone else having this problem?
& it only happens when it comes back from closing the lid while the laptop is still on.

Try resetting some of the hardware involved. See this Apple KB for details, etc.:
http://support.apple.com/kb/HT1379
Can't hurt to try, and apparently this has helped others recently.

After waking rMBP from sleep and typing password, rMBP goes back to sleep after a few seconds and won't wake for about 7-8 seconds.

Similar Messages

Maybe you are looking for