After WRT310N Firmware Version 2 update - Unidentified Network

Hi
I've owned the WRT310N for over 2 years now. I've been happy with it's features thus far. I updated the firmware previously to 1.0.9.
Recently, I upgraded my OS to Windows 7 from Vista. It's great and connects to my other hardwired network device (i.e. printer) and internet without any issues. I chanced upon a review that said the WRT310N Firmware Version 2 (WRT310Nv2_0_00_012.bin) was out and eagerly upgraded it in the router. Herein came the problem after the automatic reboot. My internet connection was unidentified with gibberish for an IP address. Strangely, my printer still connects and prints. But I can no longer access the set up page typically found in 192.168.1.1. There are no issues with my modem.
I tried many things with the assistance of the Linksys hotline in the Philippines (ref case:100408-000629). Simple 5 seconds, 30 seconds, 1 min resets, press and hold, unplug power, replug in power - Result = 0.
I tried to force ipconfig to dump the ip address, it could not release it or renew it. I tried to lower the duplex speed to 10MBPS, doesn't work. I thought the problem was the gibberish was on IPv6, by deselecting it, IPv4 wasn't able to correct itself.
Long story short, it was a fatal mistake to install Firmware Version 2 as after the reboot, I couldn't access the internet or the set up page that was necessary to reset the factory defaults. Without entering the router set up page, I can't help myself.
The kind Linksys lady told me I'm out of warranty and there's pretty much nothing I can do except by the brand new WRT610n with XXXXX features. I don't think I would as I'm very concerned about upgrading future firmwares in the light of this experience. So I'm putting this case up for your review. Hopefully, I'm the only "unique" case. =(
E

Push and hold untill lights go off usually I hold for 30 seconds. You should also turn off and unplug your modem while you do this. After doing that you should reboot your computer and then see if you can access the router, if you can but still dont have internet then you might have to release/renew the DHCP untill you get an IP. Can find that on the status tab.

Similar Messages

Hot spot s not visible after latest iOS version update on my iPad please help

hey personal hot spot is not visible after iOS latest version update on my iPad mini please help

Hey Devinder from chd,
For most issues with Personal Hotspot, try out the basic troubleshooting in the article below. It does talk about iPhone but the troubleshooting is the same for your iPad. If you are still having issues, let me know and I can see what else we can do after that.
iOS: Troubleshooting Personal Hotspot
http://support.apple.com/en-us/HT203302
Basic troubleshooting
See if your iOS device, computer, and wireless plan all meet the system requirements for Personal Hotspot.
Make sure Personal Hotspot is on: Tap Settings > Cellular > Personal Hotspot.
Check the Internet connection on your iOS device: Tap Safari and load a new webpage.
If one connection type doesn't work, try another. For example, instead of connecting using Wi-Fi, use USB or Bluetooth.
Turn Personal Hotspot off and on: Tap Settings > Personal Hotspot or Settings > Cellular > Personal Hotspot.
Install the latest version of iOS.
Reset your network settings: Tap Settings > General > Reset > Reset Network Settings.
If you still see the issue, restore the iPhone.
Take it easy,
-Norm G.

ITunes (Win7 x64) is no longer opening after the latest version update

iTunes (Win7 x64) is no longer opening after the latest version update - I have attempted an un/reinstall - can anyone offer other suggestions?
I am running Windows 7 64-bit, and am trying to reinstall the 64-bit iTunes from the iTunes website. I previously have had this working for the last few years with no major issues, the Apple Software Updater has been pestering me for some time so I finally got it to update. However now iTunes will not start, if I select the icons nothing happens. There are no iTunes applications running in the background in Task Manager either.
I look forward to your suggestions.
Thanks,
James.

1. First check if this file APSDaemon.exe is the problem here.
Close your iTunes.
Press Ctrl-Alt-Del key and choose Task Manager. In the "Processes" Tab, select the file APSDaemon.exe and click End Prosses button, then close the task manager window.
Now open itunes and see if it is working?
If that works, to prevent having to do the same process everytime you restart Windows, go to. START button, type in
MSCONFIG
Hit ENTER
Click STARTUP Tab, Uncheck "Apple Push", click OK.
Restart Windows.
2. If that fails, refer to following article to remove SC Files
http://support.apple.com/kb/TS2363
3. If that fails, repair or reinstall your Quicktime. START / CONTROL PANEL / PROGRAMS N FEATURES / hightlight QUICKTIME and click REAPIR.

Can not open itunes after installing latest version update 11.2

Can not open itunes after installing latest version update 11.2

See Troubleshooting issues with iTunes for Windows updates.
tt2

Lumia 925 Firmware Version Update

need help.....
My Lumia 925 firmware version is 3047.0000.1325.2001 which I think, is very old. I bought this phone in India (in august).
I am using this phone in Malaysia, tried updating it but not able to. Took my phone to Nokia Care,as per them phone may be locked out if I do phone update in malaysia, also my warranty will be void.
Please suggest me options I have. Do I have to come back to India to do update.
I wanted to use 4G but beca of firmware version i cant
Help will be much appreciated.
Amrit.

why do you think it's too old? it has been released only a few months ago... the xxx.2001 is not the year, it's a part of the version number, that's all.
The silence will fall

Mac Book fails to boot properly after EFI Firmware 27 update

hi
I have a strange boot issue having (tried) to install EFI 2.7 update.
When I restart the laptop, it 'chimes', displays a grey screen ... then chimes, displays a grey screen , ... for ever
I hit the bower (off) button for 5 secs or thereabouts, and restart ... same thing
I do this 4 times and finally it reboots.
But the EFI update still appears as needing to be installed (software update tells me it is not installed). Update history shows however that it IS installed.
I can go through this process any number of times ... I now have Software Update history showing quite a few installs opf the EFI 2.7 update.
If I just do a restart WITHOUT installing, I also go through the same fail to restart / fail to start / ... / eventually restart sequence.
So it seems now that the laptop will only start after 4 failed restarts and finally it starts ...
After starting it all appears to be perfectly fine.
Nothing strange in the console logs that I can see. The failed reboots don't seem to register in the console logs - I suspect that the failure to restart is pretty early on in the boot sequence, well before it tries to load any semblance of the OSX kernel. It is almost as if it is trying to boot from someplace other than the disk ... until eventually it gives up and tries the disk. (I have tried booting with and without network cable - no difference) I don't know enough about mac bootup sequences to know if there is some config/setting that is screwed up causing this odd behaviour. I sirt of feel it must be setup/software related, but could be wrong.
Odd.
Any ideas?
- chris

I have a MC721LL/A early 2011 15.4" MacBook Pro i7. After I installed this firmware update my Mail would not load saying the version I was trying to start was not compatible with the OSX version (not sure whether this was an OSX update issue which I think I did at the same time). But the biggest problem I have is that I cannot boot my machine. It boots to the Apple logo and then emits 3 beeps repeatedly. I am on vacation in Osaka, Japan and the Apple Store here told me after running some analytics that the logic board is not seeing the RAM. After reseating the RAM multiple times (both original and replacement DIMMS), it still won't boot. The Genius Bar guy said very nicely that it is out of warranty and needs a new logic board, costing over $500 and taking a week at the factory. He recommended spending the money on a new MacBook instead. Since my machine is 15 months old, I am not very happy about this. The machine was absolutely fine before the firmware upgrade. I will wait till I get back to the US and get a second opinion from my local Apple Store. I can't accept that a 15 month old MacBook Pro very lightly used can develop such a catastrophic failure.

Home Hub 3 - Firmware Version & updating

Hi all - brand new on here. Apologies if this has been covered already (have had a look and couldn't find an answer).
I have just been provided a HH3 as a replacement for a HH2. I noticed the issue re the time being an hour behind etc and then noticed there may have been a fix via a firmware update. My HH3 has Version 4.7.5.1.83.8.57.1.3 (Type A). According to the BT website it looks as though I should have 4.7.5.1.83.8.94.1.11 (Type A).
I appreciate the unit updates automatically - I was wondering whether this should have happened straight away (unit has now been connected for a day or so) or whether it will happen over a period of time?
Any thoughts / ideas??
Solved!
Go to Solution.

it will normally happen overnight there is no time scale for the update to occur
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Why won't my ipod classic 80gb no longer synch after latest itune version updates

Why will my ipod classic 80 g ipod no longer synch after upgrading my itunes? I went from the very user freinly itunes from a few years back to the latest versions and have been having these problems.
Doesn't synch at all.
Synchs only partial playlists selected.
If it synchs it leaves out multiple tracks.
I mainly use my ipod for listening to Audio books that I have ripped unto mp3's myself. It also won't do my music or podcasts.

I have the same problem with windows 7 and msy ipod classic will not sync...have no access to thousands of songs and playlists..Help!!

After the recent version update (and after my cat knocked my router down) Firefox is just not working. I can access the internet via another browser BUT all my passwords are saved in Firefox.

I am using a PC with Windows 7, and like I said, the other browser seems to be working just fine. I just MISS my passwords and really don't want to go through all the work and trouble of requesting new ones from ALL the sites I use passwords for ! Please HELP :)

Your second post said 'ignore this" so I guess everyone thought you had got it fixed....
When you connect through your router you have two instances of DHCP going on...one is your DSL modem giving your router an IP address on it's WAN interface. The other is the router giving your computer an IP address via the router's DHCP server. The IP the modem gives your router is in the 192.168.1.0 network. Unfortunately, by default, the LAN IP address reange on Linksys routers is also in that range. To get this to work, you need to set your LAN ip on the router to 192.168.2.1, so that the LAN and WAN interfaces of the router are in different networks.
To do that, unplug the router from the DSL modem, power it and your computer down, then connect the computer to the router using an ethernet cable. Power up the router, and the computer, then browse to 192.168.1.1. Change the LAN IP on the router setup to 192.168.2.1, save the configuration, then reboot the computer. Once the computer comes back up, browse to 192.168.2.1...you should be able to get to the router setup GUI.
Power down the router, and the DSL modem, connect the router to the modem via the Internet port using an ethernet cable, then power up the modem, then the router....you should be good to go...
Tomato 1.25vpn3.4 (SgtPepperKSU MOD) on a Buffalo WHR-HP-G54
D-Link DSM-320 (Wired)
Wii (Wireless) - PS3 (Wired), PSP (Wireless) - XBox360 (Wired)
SonyBDP-S360 (Wired)
Linksys NSLU2 Firmware Unslung 6.10 Beta unslung to a 2Gb thumb, w/1 Maxtor OneTouch III 200Gb
IOmega StorCenter ix2 1TB NAS
Linksys WVC54G w/FW V2.12EU
and assorted wired and wireless PCs and laptops

E70 firmware version update

I have an E70 running the latest firware release (as far as I can tell):
2.0618.07.10
31-08-06
RM-10
Nokia E70
Product Code: 0538292
I've had this phone for about two months now and I have to say that it is hardly an improvement on my old 6822.
It seems to suffer with the most obvious & glaring bugs. To name a few these would be:
i) Profiles: Unable to set individual ring & message tones from the gallery (phone or card memory).
ii) Calendar app: does not provide for copying occurrences to other dates/times.
iii) Calendar app: does not allow moving of meetings using a UI.
iv) Calendar app: changing the date on x1 instance of a repeatable occurrence is not handled correctly - can only edit the whole set.
v) Calendar app: To-Do notes without a due by date are set to 01/01/2007 (which is daft).
vi) Word processor app: does not handle new/end-of-line characters properly from either UNIX or Windows text documents; leads to funny errors when editing a document pushed to the phone.
I could go on. But it strikes me as odd that something that worked so well on the 6820/6822 models is so fundamentally dysfunctional on the 'better' model.
Does anyone out there know where an update that fixes some of these problems can be found? If not, then can someone from Nokia development offer anything?
I'd be very grateful to hear something as this is becoming a complete pain to use now.

check the checkbox @ top of this frame
6280 RM-78 —>6288 RM-78 V 6.43
N73IE RM-132 V4.0736.3.4.1

How do I find my firmware version G5 dual 1.8

Where can I find the firmware my computer is running?
Thanks

Boot with an Apple wired keyboard command-option-o-f to get the boot ROM version.
http://www.xlr8yourmac.com/g5/powermac_g5_docs_updates.html says:
G5 Boot Rom (Firmware) Versions: (Update - as of April 2004 G5s are shipping with boot rom v5.15. In late 2003 Apple released G5 firmware 5.1.4 update for 2003 models and in Nov 2004 released a 5.1.8f7 update for June 2004 models. The comments below were from early owners before that release.) After the report about early G5 shipments reportedly having problems with mixing 3rd party RAM with the OEM RAM (Hynix brand reportedly) I wondered if the boot rom version had changed since the first shipments. The S/N XB337xxxxx Dual G5 here (shipped 9/15) has rom version 5.0.2f2 (as reported by Apple System Profiler). Several readers sent their G5 boot rom versions:
" Dual 2 Ghz BTO in UK
CK338xxS-NVB
(boot rom version) 5.0.5f0
Tan "
Another Dual G5 owner (very recent shipment) wrote he has an even later boot rom version:
" Mike, I got my G5 Dual 1 week ago, Just looked at the Boot rom version and it is newer than others mentiond in todays news."
Machine model
PowerMac7,2 (version = 2.2)
Boot Rom: 5.0.7f0
And another report of 5.0.7f0 firmware:
" Mike, we have three CTO machines, built 9/19 (1) and 9/22 (2) boot Rom on all three - 5.0.7f0
-- Fred C.
General Manager
TheTroupe Modern Media Design & Production "
A reader with 5.0.7f0 firmware noted he still had problems using CL2 dimms (even without any CL3 OEM dimms installed based on his previous comments) - so there's still a requirement for DIMMs to have CL3 timing in the SPD. One reader later wrote he had an even earlier boot rom version than mine - 5.0.1f0.
Maybe Apple is waiting to accumulate fixes/changes before releasing a public update - but I'm hoping they will soon release a firmware update for the G5s which might solve some of the quirks that some owners have seen.

How to downgrade my firmware version after a "succesful" update?

Dear Macusers,
Is there any way to downgrade my firmware version from 1.5.1 to a lower version? Even if my firmware update has been applied succesfully? I cannot use just the firmware restore CD because that is for an interupted or failed update.
Greetings,
Tim

Hello,
Many thanks for your reply. Yesterday I posted a topic about this problem with some more details. I hope this may help.
+"Since today my trackpad and keyboard doesn't response anymore. This problem started after I exit from sleep mode. Then I get a security form where I can enter my password, but I couldn't. So I restarted my macbook pro for about 5 times, removed my adapter and battery, but it doesn't work.+
+After that I went to iFactory and they said it is apparently because of my latest firmware update 1.5.1. But why does this happen a week after I installed this update? Anyway, he suggested me to downgrade my firmware version with a firmware restore CD. Well it sounded as an straightforward and easy solution until I read that the restoration CD doesn't work when the firmware update already has been applied correctly.+
+I have read some other topics about keyboard issues and some points are relevant for me:+
+I'm be able to use an external USB mouse and keyboard.+
+At system profile by USB, only my iSight, Bleutooth USB host controller and external USB devices are displayed.+
+The keyboard background light works properly+
+This problem happens all of a sudden without intervals or strange behavior.+
+Using Leopard (10.5.2) and Windows XP via bootcamp+
+I hope I can solve this problem really quick because I need my Macbook Pro badly for my study. Thanks in advance for studying my problem.+
Greetings,
Tim

After Safari 7.06 update, whenever I connect to RSA Juniper Network Connect, my internet connection get disconnected. It was an issue with old Safari versions. It was fixed around 6 months back with one of Safari update. But, now it is broken again.

After Safari 7.06 update, whenever I connect to RSA Juniper Network Connect, my internet connection get disconnected. It was an issue with old Safari versions. It was fixed around 6 months back with one of Safari update. But, now it is broken again.
Anybody experiencing the same problem and any suggestions to fix the issue.

Hi ..
Try this discussion > Can't connect to Juniper VPN

Wlan error after a firmware update

Ok there seem to be many posts about this issue but i cannot find anything that seems to work for me.
I not to recently updated my N95 8Gb firmware to 20.0.16 and found that I was having errors with WPA on WLan, previously I had no such problem and the issue only occured after the firmware update.
to add some more info I am on a network with a linksys wrt300n
I have tried wep it works but dont want to compromise security.
All computers on the network are using wireless g and the key is definitely correct when entered
any help would be most appreciated

I don't have N95, but if the firmware is updated to latest version the wpa most likely wpa2. Having wpa in place of wep gives only very little added security for a determined hacker! It will only takes 30min to an hour to crack that. Security like that deter only the free net riders. Try if there is upgrade for your modem/router, its usualy the case. For home network wep or wpa sufficed.
Knowledge not shared is knowledge wasted!
If you find it helpfull, it's not hard to click the STAR..

Will firmware version 4.1.7 automatically update to 4.1.9?

I recently upgraded to OS 10.3 from OS 10.0 on my Imac 700MHz G3. The installation documentation said that I would be prompted to upgrade the firmware if I needed to. I was not prompted so I went ahead and did the OS 10.3 installation. The firmware remained version 4.1.7f4 after the install.
Not too long ago I went through the same procedure on my Imac 400MHz DV. The only difference is that I started the upgraded process from OS 9.I, then to 9.2.2 using the updates (ending at the latest version of 9), then to 10.0, and then to 10.3. And finally updating with 10.3.9 combo to OS 10.3.9. During that whole process I never new about firmware and never checked to see what version I had before starting this process. After all of the above installations were finished I ended up with firmware version 4.1.9f1.
My concern is with the 700MHz G3 IMac. I'd like to update to 10.3.9 using the combo update but I'm concerned about the firmware. Will firmware 4.1.7f4 be updated automatically to 4.1.9f1 after the combo OS 10.3.9 is installed? Or should I erase the disk again and start over by first installing firmware update 4.1.9? Actually if that were the case I wouldn't be able to update my firmware since I don't have the correct bootable version of OS 9 on disk that is required for that computer. However my previous experience with the installations on the 400MHz DV suggests to me that that the firmware will automatically be updated. But I would like confirmation from the experts. I'd hate to spend all that time downloading and installing all of the latest updates (Combo 10.3.9, etc.) only to find that the firmware version is incorrect.
Thanks!
Al

Al,
I don't understand your anger. In your first message
you posted that you installed OS 9 and updated it to
9.2.2. So why don't you do that again on the 700 MHz
iMac?
I find it very amusing that somehow you see anger in my post. That is realy very funny! The reason I didn't just simply install OS 9 on the 700MHz Imac is stated in my original post. I would need a special (the original disk that came with this computer) bootable OS 9.1 disk to install 9.1 on this particular computer. However if there are retail 9.2 or greater disks available then that would work to. I own a retail version of 9.1 that I used for the 400MHz Imac. That wont work on the 700MHz Imac. So now I have to buy a another OS 9 disk. Thanks for your input. Al

After WRT310N Firmware Version 2 update - Unidentified Network

Similar Messages

Maybe you are looking for