Agent get stucked in Reserved State

HI CUCCE gurus,
Need assistance on this issue. In our remote office, our Sales Team has a linegroup setup, the Sales extensions are part of the linegroup and at the same time its their ACD line when they logged in to Cisco Agent Desktop.
The issue is, when they got a call from the linegroup their CAD state change to "Reserved" and it stuck from that state and nothing they can do to change the state but to logoff, close the apps and log back in.
I enabled debug on once of the Sales CAD (see attached output).
Any troubleshooting tips that you can advise or detailed steps to check from our system.
Our CAD is 7.X
Our CUCCE is 7.X
Our CUCM 7.X
Thank you.

Hi Jhun,
Agent stuck in reserved state it means, the ICM has reserved the agent, but the call is not getting delivered to the agent extension.
If you are using SIP trunk, you would probably need to check the CSS and Partitions over the trunk. Also, any recent changes made on the CSS of the SIP trunk you would need to reset the SIP trunk.
The CSS on the SIP trunk should contain the partition of the phone.
Also, you would need to check on the Agent targetting rule in the config manager of the ICM. The agent extensions should be added to the Agent targetting rule
Hope this helps!!!
Cheers,
Dass
Please rate useful posts

Similar Messages

Cisco Agent Desktop stuck in Reserved

Hi guys...
we have a UCCE 7.5.7 with CAD 7.5.8... what we have found is that when there is a large volume of inbound calls the CAD gets stuck in Reserved state for 30 seconds before it gets a call...
Investigating this i came accross a reference that this happens when an Agent is reserved for an inbound call but the customer hangs-up at that very moment the agent was reserved...
now... 30 seconds is quite a long time for an agent to be Reserved without doing any work... is it possible to change this behaviour and maybe cut the timer down to 5 seconds which would be acceptable...
thnx

I would use your lab system and try the registry setting RouteRequestTimeout (default is 30000 so probably msecs).
\ICM\\PGn[A,B]\PG\CurrentVersion\PIMS\pimN\EAGENT\Data\Config
I don't know if this is correct, of course. But it looks tantalizing
Regards,
Geoff

Ucce cad agent stuck in reserved state

Dears,
It is a UCCE system with CVP and CAD version 9.0
The issue is that when the call is to be delivered to an agent, the CAD is stuck in the reserved state for around 20 seconds then it goes to the Ready state and the caller gets disconnected since I'm not configuring a queue yet.
Has someone faced a similar issue?
Your help is greatly appreciated.
Thank you in advance.
Lara

Actually it turned out to be a call manager issue. The partition of the agent's extension was misconfigured.
Regards.

IPCC - agent stuck in reserved state

HI
I have a problem, Desktop agent goes in reserved state are using Cisco Contact Center Express 7.0(1)_Build168 This contact Center is integrated with CUCM 7.1.3.30000-1.
Logs attached .
PD:I already checked the CSS configuration of the agents and cti ports.

Hi Carrion
The problem is when the call is transferred from UCCX CTI port to your agent:
602574: Jun 15 19:28:34.161 COT %MIVR-SS_TEL-7-UNK:CallID:114 MediaId:1342/1 Task:18000000195 consultWithoutMedia gets CiscoJtapiException: 0x8ccc0088(CTIERR_CONSULT_CALL_FAILURE)::Consult Call Failure
602575: Jun 15 19:28:34.161 COT %MIVR-ALARM_MGR-3-UNK:MIVR alarmwriter queue is full some alarms will be dropped
602576: Jun 15 19:28:34.161 COT %MIVR-SS_TEL-3-CONSULT_FAILED:Consult failed: All Call ids=CallID:114 MediaId:1342/1 Task:18000000195,Extension=6058,Exception=com.cisco.jtapi.PlatformExceptionImpl: CCNException not handled: com.cisco.cti.client.CCNException: ,Failure reason=consult gets error 0x8ccc0088=CTIERR_CONSULT_CALL_FAILURE
602577: Jun 15 19:28:34.161 COT %MIVR-SS_TEL-3-EXCEPTION:com.cisco.jtapi.PlatformExceptionImpl: CCNException not handled: com.cisco.cti.client.CCNException:
So the call gets placed back into the queue and then fails to dispatch succssfully to the agent again.
Can you please confirm how you are making these calls, are they from the PSTN or internally to the UCCX?
Also please check MTP and make sure you have allowed media resources as the system has to beable to place the call on hold while it transfer.

UCCX 7.0 - Agents in reserved state and calls stuck in CSQ

Hello all,
I have got a following issue with our UCCX 7.0 installation - there is a team of agents and some of them intermittently stuck in reserved state for no reason.
I went to real-time reporting and found lot of calls stuck in CSQ, which I believe is related.
Other teams (which uses different IVR scripts) are not having these kind of problem - that led me to conclusion that something may actually be wrong with the scirpt itself. I am going to add "dequeue" step before "Goto VOICEMAIL" under transfer menu for all three options, but not quite sure if that is cause and solution for the problem. Could you guys take a quick look on attached script, I might be missing some part of picture here.
Thank you in advance,
Peter

Hi
Some things to check first:
1) Agents are not members of pickup groups - this is a common cause of such problems
2) Do the agents all receive calls sometimes? Are they all in the same partition? Verify that the UCCX CTI ports can call all of the agents...
3) Check the release notes : http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_7_0/release/notes/uccx701rn.pdf
There is an 'unsupported actions' section that lists things agents should not do on Page 15 onwards. Pickup is the most problematic of these, but others are very common causes of stuck-in-reserved and stuck calls.... far more common than scripting errors. If in doubt, disable the options (by removing pickup groups from their lines, and assigning a softkey set that doesn't include the listed keys) and see how it goes...
I've had a quick look over your script and see no major cause for concern.
Regards
Aaron
Please rate helpful posts...

Workflow stuck in starting state after applying SharePoint 2010 CU December 2012

I have custom visual studio workflow which are associated with Custom content type. workflow gets triggered automatically when a file is uploaded to SharePoint. Everything was working fine till when i apply the following CU
http://blogs.msdn.com/b/joerg_sinemus/archive/2012/12/27/sharepoint-2010-and-december-2012-cu.aspx
After applying this my workflow get stuck in "Starting" state.
No error were logged in 14 hive logs.
Thanks in Advance!

It took me a while but I came up with a work around. There is a PowerShell script below that can be used to trigger the workflow. Hopefully this will hold all of us over until the official fix arrives.
First remove the auto start on change or new from the affected workflow
Edit the script below to match your environment
Add the script to Windows task scheduler with the PowerShell.exe in the command line
This assumes PowerShell.exe is in the path
Then add the full path and script name in the add arguements text box
Script:
#The purpose of this script is to start the SPD workflow with the windows task scheduler for a trigger
#This should avoid the check in-out issue caused by the December 2012 SP CU patch
#This needs to be run on an account with membership in the farm administration group for SharePoint and Shell in SQL
#You can use a find and replace to replace the server and other names with your actual names
#There are no status messages being used since this will be a scheduled task in the Windows task scheduler
#Add SharePoint modules and create variable space
add-pssnapin microsoft.sharepoint.powershell
start-spassignment -global
#Open the web site, list and the workflow
$site=get-spsite %site url%"
$web=get-spweb %Web url%
#Open the %affected% library or list and workflow association
$%affected%=$web.getlist("%affected%")
$manager=$site.workflowmanager
$culture=[system.globalization.cultureinfo]::currentculture
$wfname="%affected workflow name"
$association=$%affected%.workflowassociations.getassociationbyname($wfname,$culture)
$data=$association.associationdata
$wfrunoption=[microsoft.sharepoint.workflow.spworkflowrunoptions]::synchronous
#Start workflow
foreach ($item in $%affected%.items) {
$site.workflowmanager.startworkflow($item,$association,$data,$wfrunoption)
stop-spassignment -global

Captivate demos stuck in Loading state when shared in an Adobe Connect meeting room

We have published several Adobe Captivate demos directly to Adobe Connect content library (using both Captivate 5.5 and 7). The demos work fine when accessed directly using the URL assigned in the Content Library. However, when the demo is shared in a meeting room share pod, it gets stuck in Loading state and nothing is displayed. Trying to understand if this is a bug or if there are certain publishing settings in Captivate that are causing this problem.

Have you looked at the logs on the Connect server (Error or Access) to see if there is something there to help identify the problem?
If you put ?mode=xml after you meeting room, do you get any clues about the problem in the text that shows below the connection error message?
Have you tried the test my computer page to see if there is a problem that can be identified there?

Risk Analysis Batch Job Stuck in Ready State

Hi,
I am not able to schedule Risk Analysis Batch job in RAR.The job is getting stuck on READY state(for unlimited period) and not performing any actions.
Nothing is displayed under job history or job logs with job ID.I have check background job demaon ,connectors and other miscell. options but not abl to find any clue.
Even i am executing risk analysis for single user,it's not happening.
Rgds,
Mukesh

For your problem, of job not getting schedule....it seems Deamon is not running.
To delete status of job which are in hung status
change VIRSA_CC_SCHEDULER job id should with status five will show job aborted.
are you using connection type 'Adaptive RFC', don't use it, use SAP JCO.
and restart your GRC box.
Regards,
Surpreet
please do check backend system, for VIRSANH is installed or not.
Edited by: Surpreet Singh Bal on Jan 28, 2011 10:32 AM

Agent reserved state

Hello. Is available CUCM 4.3(2)sr1b and UCCX Enhanced 6.0(1)sr01. Periodically (1-3 times a day) agents pass to reserved state and can be in reserved state different time. Forum messages on a theme are seen, but the problem remains.
I give an example. CallID - 26248, agent - 1004. The agent remained in reserved state 0:02:06 AM.
19438482: Sep 04 16:20:14.729 MSD %MIVR-SS_TEL-7-UNK:CallID:26248 MediaId:125034/1 Task:21000060839 waiting for consultative transfer or conference to finish before transferring to extn: 1004, transferStart=true, conferenceStart=false, termConnState=4, disconnected=false
19438704: Sep 04 16:21:15.603 MSD %MIVR-SS_RM-7-UNK:checkContacts(), agent's Reserved duration:60874 Threshold:20000
19438928: Sep 04 16:22:20.602 MSD %MIVR-SS_RM-7-UNK:checkContacts(), agent's Reserved duration:125873 Threshold:20000
19438929: Sep 04 16:22:20.602 MSD %MIVR-SS_RM-3-CLEANUP_STUCK_CONTACT:Removed stuck contact: The name of the method that invoked another method=125034/1
19438930: Sep 04 16:22:20.602 MSD %MIVR-SS_RM-7-UNK:Processing msg: SessionCancelledMsg (Rsrc:125034/1 Cause:SESSION_CANCELLED_CAUSE_CONTACT_DROPPED)
19438990: Sep 04 16:22:20.602 MSD %MIVR-SS_RM-7-UNK:Rsrc: Operator4 New State:AVAILABLE Old State:RESERVED Reason code:0

Now we are getting this error on multiple agents randomly.
we found this error on cmpg
15:25:06:620 pg4A-pim1 Trace: FreePreRoutedCall: Head Inst: N26008 CreatedByPreCall: T PeriphCID: -1 Queue Count: 0 RouterCallKey=(149897/92397)
15:25:08:088 pg4A-pim1 Trace: TelephonyDriver::CSTASupervisorAssist: No dialed number for ID -1
15:25:08:088 pg4A-pim1 Trace: DeskLinkPeripheral::SetAlert - (TelephonyDriver::CSTASupervisorAssist) Setting ERROR Alert #9 - 15:25:8 DialedNumber

W510 Solid State Drive (SSD) Gets Stuck Causing BSoD. Why?

Hey guys, this has been a problem for a while now, and it is really mind boggling ... I have a Lenovo ThinkPad W510 laptop with a 256GB Crucial M4 SSD drive. Ever so randomly the drive just hangs, the LED light that the drive is trying to load something stays "ON" for up to 5 minutes or so before it finally goes into a Blue Screen of Death (BSoD). Once it goes into BSoD the laptop reboots and it gets stuck on the ThinkPad motherboard logo, eventually it will display "ERROR 2100: HDD0 (Hard Disk Drive) initialization error (X)" Where X is usually 1 or 2, sometimes 3 but rarely. It will not function again until I physically turn it off and back on using the power button.
A little bit of background about the problem, this is my 3rd Crucial 256GB M4 SSD, Crucial has been very helpful and they went as far as replacing the drive twice, i am starting to highly doubt its a drive issue, I think it could be something from the laptop itself. To be more clear, my laptop has also been serviced back in March (Motherboard was swapped as well as keyboard), parts failure. It was all done in very timely manner and everything was OK after the swap.
A representative from Crucial told me that this is a classical problem with the SATA controller driver handling TRIM, he said the drive is getting stuck in an infinite TRIM state which causes the BSoD, after that the drive goes into some sort of a "panic" mode to protect itself and doesn't function again until a full power cycle. (thus the need to turn off and then on the laptop) he also added it could be fixed by installing the correct SATA controller driver.
I have tried to use the default windows SATA controller driver, and I have tried to use the Intel one too, and it seems to happen less often with the windows drivers, but overall, it happens at least once a day. It is really frustrating and I am not able to get anywhere with it.
Any help or advice is highly appreciated. I am considering getting rid of the Crucial SSD altogether and just using Intel SSD instead, but I am really doubtful that it is the SSD's fault especially that its the 3rd one I use. I also know a couple of friends who own ThinkPads with Crucial M4 SSD inside them, and they seem to be working very well for them.
Thanks in advance,
Al.

Hi again,
Ok so I have applied the fix you have mentioned above, and it did improve (lower) the frequency of the problem happening. It really improved a lot significantly when I uninstalled the Intel drivers and used the Windows 7 built in SATA controller drivers.
However, ... it still happens ... less frequent, but it still takes place, my SSD still gets stuck at least once in 3 days now, or once in 2 days (after severe testing) and the same scenario happens. I am really stuck at this point, and not sure which direction to take.
Any help would really be appreciated, if you have / know any method to debug the BSoD's I get and a way to locate the source of the problem I am willing to go through it 1 by 1 and solve this problem before deciding to finally just giving up on the drive altogether.
Sincerely,
Al.

Updates getting stuck in V2 processed state

Hi,
In our ERP production system EP0, update entries are getting stuck
in 'V2 Processed' state.
Details of the same show that the collective run state is in initial
state for functional module 'MCEX_UPDATE_03'.
Please find the attached screenshot of details.
These updates are gettin stuck for specific transactions like MIGO.
We have already tried running the report RSM13005 but it has not helped.
Please look into it urgently as the system is a production system.
Thanks in advance.
Regards,
Suresh
Edited by: suresh k on Sep 26, 2008 2:38 PM

Hi
As you checked in transaction SM13 they are stucked in Initial state. There was various states associated with the update like INIT and ERR.
What is INIT status:
Update records which have not yet been processed have the status INIT or AUTO. INIT refers to a complete update record (header, function module call of update and data elements are present), which has not yet been processed however.
What to do: SM13 -> Update records -> Update -> All records/Single
you can set the update administration so that all records with the status 'INIT' or AUTO' (all update records which have not yet been updated) are processed (as far as possible).
Warnings: please check with the user who posted the updates in the first place - make sure that they have not already reposted the update manually. If you are in doubt, please re-enter the data manually rather than using this update function.
Hope this helps!!
Kind Regards
Esha
Edited by: Esha Rajpal on Sep 30, 2008 5:06 AM

Launchpad transitionary state (translucent) gets stuck, pages do not slide properly. Mavericks.

I have a problem with A LOT of things on Mavericks: what happened to releasing finished products, Apple?
This particular one pops up a lot.
When I pinch with four fingers to bring up the launchpad, it sometimes gets stuck in its transitionary state. You can try and simulate this problem yourself: just pinch very slowly and you will actually get to witness the transition in slow motion as you move your fingers. This transitionary state where the launchpad is translucent and becomes more and more vivid is the problematic step: sometimes it gets stuck before it reaches its full vividness. Here is a screenshot of it stuck:
When it is stuck in this transitionary state, it is still active! If I click on an app, it sitll opens, and if I click the spce between apps, it disappears.
Another issue that I have is when the launchpad opens properly and I try to switch between pages. If I do a quick swipe to the side, the page is supposed to switch. If the movement was not sufficient in magnitude, the page is supposed to bounce back to its original position. There is a certain place in that range of movement magnitudes, however, that results in a glitch: the page moves a little bit to the appropriate side, but does not bounce back, nor change the page. If I do this repeatedly, I can actually slowly advance towards the next page, little by little:
This is not me being tricky and grabbing a screen shot between pages. This is the results of four or five of those side swipes that do not result in page change or a bounce back. It just gets stuck in its current position, as shown above. Is anyone aware of a fix for this issue, or should I just submit this to Apple for a fix?
PS
This happened in the original Mavericks release AS WELL AS it happens in the updated 10.9.1 version.

I noticed this problem just after updating to Mavericks. Hopefully it will get fixed soon.
http://www.youtube.com/watch?v=yEHtTJ9_ob8

Solid State Drive = Gets stuck

Hello,
I recently bought Intel's 520 Series Solid State Drive. I swapped my hard drive with the SSD, booted on a Snow Leopard disk. Opened Disk Utility, formatted my drive (Mac OS Extended Journaled) and installed Snow Leopard. After I installed the applications I needed, I finally upgraded to OS X Lion. But now I can't browse the net, work on applications or do any other task without getting a beach ball every 2 - 3 minutes. My MacBook Pro gets stuck a lot for some reason. (I never had this issue with my older hard drive)
I have the latest version of OS X Lion, but no firmware update was available for my SSD. I have an early 2011 MacBook Pro.
Does anyone have any suggestions on how this can be fixed?
Thanks.

What model MBP do you have? Older systems don't handle SSDs as well as newer system. Especially systems that don't do the 6GB SATA interface, which is what the Intel 520 series is. Although they state the drive interface is baclwards compatible that does always mean it will work correctly on older systems that only do SATA 1 transfers, 1.5GB.
You could try a Clean Fresh install of Lion without first installing SL. That may or may not work.
Just boot to the recovery HD partition and erase the Macintosh HD partition then re-download and install Lion.

How to set the number of rings for the agent phone rings before it get the not prepared state

hi, how to set the number of rings for the agent phone rings? before it get the not prepared state.
thanks

The following assumes that you are using ICM with an IPIVR etc (not using CVP), as the answer is different for CVP
What you are looking for is called "Ring no answer time". It is set in the Agent Desk Setting List tool.
Regards,
Kevin

Creating table statement gets stuck

Hi everyone, i can use "select" statements without any problem but when i want to create a table with 100-1000 rows, it gets stuck and never returns and after i close the sql navigator and restart it, it creates my table easily but after 20-30 seconds when i want to create an another table, it stucks again. What can be the problem??(At the first times that i use sql, there was no problem)

Hi,
It's a bit difficult to answer. Members will try to help you about database problems but in this case it's impossible to know if it is a database problem. If you have the needed system privileges and some quota on a tablespace there is no reason you wouldn't be able to create tables in an Oracle database !
Ask your DBA to try directly with SQL Plus but if he confirms it's OK there is a problem with your SQL Navigator tool.
Best regards
Phil

Agent get stucked in Reserved State

Similar Messages

Maybe you are looking for