Agilent 33220a labview 7.1 driver

Hi,
I want to ask LabVIEW 7.1 driver for Agilent 33220A. I installed 7.0 and as a result it doesnt work.
Can somebody help me about this matter
Thanks a lot

thank you very much for your quick answer,
After  I installed driver to the int.library, the blocks of the driver doesnt seen as seen in the attached.
Attachments:
hata.JPG ‏40 KB

Similar Messages

  • Agilent 33220a drivers for LabVIEW 2009

    Hello,
    aprox. 3 Weeks ago i downloaded a driver for the Agilent 33220A Waveform generator.
    Well i lost that one and tried to download it again from here:
    http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E9066659CE034080020E748...
    The Problem is that the downloaded File is 0kb of size.
    Anyone else got this Problem? Maybe someone can tell me another download link.
    Thanks!

    Well i'm at home now and you are right, it works
    It just would not work at the University.
    Anyways tanks for your time!

  • Agilent Technologies 54200A Oscilloscope LabVIEW 8.2 driver

     Hello: I need LabVIEW 8.2 driver for HP 54201A DSO
    Regard fahim

    http://www.ni.com/downloads/idnet/
    I'm sure you're more than capable of typing "54200" into the search box.
    Also, from within LabVIEW,  Help -> Find Instrument Drivers.

  • Unable to load LabVIEW RT from drive

    Trying to boot RT on PXI-8187 controller with original setup, what ever RT boot selection is used either hardware switch or BIOS RT boot option, the terminal will show the following:
    Unable to load LabVIEW RT from drive!
    Booting safe mode from ROM...
    mount: Mounting /dev/Ma1 on /home/ftp/c failed: Invalid argument
    Entering safe mode.
    IP address is: 0.0.0.0
    Of course after that you can't do any thing to configure the RT target from the MAX on the host computer.
    Please Help.

    Hi,
    I used the recovery CD to change the file system to NTFS, it took a while and it installed windows XP from scratch differently from FirstWare that ghosts it (I think). And it didn't install any NI stuff what so ever.
    At the end I got the same result as with using the remote system format disk option.
    i.e. The RT controller boots in safe mode displaying the previous message without the mount error but this time I can configure the IP address.
    Still I can't install software to it, I get the list of features to install, I select them and press next, then I get a dialog saying:
    Cannot process install because other dependencies are required:
    LabVIEW RT 1.0.1
    LabVIEW RT 6.0.1
    LabVIEW RT 6.1.0
    LabVIEW RT 7.0.0
    LabVIEW RT 7.1
    Is this a host or RT Controller issue now?
    What's next? Thanks for the help

  • Fixed number of pulse using agilent 33220A

    Hi all,
    I am trying to produce five pulses with Agilent 33220A function generator ..
    i am attaching my VI for your review...
    the problem is ,, i can able to send the command for digital pulse of required parameters ,, and the function generator starts producing constant pulses...
    but i want only five or fixed no of pulses ,,,
    i have tried using the loop concept and not succeded ,,
    Any suggestions would be grateful...
    by Rozita
    Attachments:
    Agilent33220A-pulse.PNG ‏51 KB

    You need to configure a burst in TRIG mode and send a software trigger to start it. Refer to the 33220A manual for more details.
    Ben64

  • Labview 6 compatible driver for HP89410A Vector Analyzer

    Does anyone know where I can get a labview 6 compatible driver for an HP89410A Vectory Analyzer?
    I have found labview 7 and labview 8 drivers for the hp894xx family of devices, however I cannot use them as I only have labview 6.
    Barring a prewritten driver, how hard would it be to convert a labview 7 driver to make it compatible with labview 6?

    The conversion is easy since there is a VI Tree VI in the driver. Since the driver was originally written in 1999 and has been up-converted to 7.0 and 8.0, saving it back down to 6.0 shouldn't be an issue.
    Attachments:
    hp89400_6.zip ‏1194 KB

  • LabVIEW 2010 FPGA Driver for Xilinx SPARTAN 3E Starter Board

    Dear Friends,
    Is there any possibility to release a LabVIEW 2010 FPGA Driver for Xilinx SPARTAN 3E Starter Board?
    Regards,
    wedo
    Solved!
    Go to Solution.

    Hi Brad,
    So glad to get your post here!
    I’m looking forward to download the new installer.
    I wonder whether the new driver will support the 10/100 Ethernet Physical Layer Interface, since the last drivers aren’t support this feature!?
    Also, will be any new examples included with the new driver? For instance: an example for the StartaFlash Memory; I have done an example for this but I couldn’t get it work! I don’t know why! You may check my post and the example in the following link!
    http://forums.ni.com/t5/LabVIEW/Spartan-3E-StrataF​lash-Memory-wrong-reading/m-p/1030898
    By the way, is there any plane to develop a driver for the Spartan-3E (1600Kgate) kit? Both kits (500KGate and 1600KGate) have the sample on-board peripherals, the only difference is in the number of Gates (FPGA chip). I think all that is needed is to add the component ID (29597843---->3E1600) and revise the xc3s1600e.bsd and 3sXXXe.nph.
    Thanks in advance & kindest regards,
    wedo

  • Bug in Agilent 34401 LabVIEW driver?

    I was surprised when I tried to use this driver in a larger application. One of my other drivers puts a warning about "more data may be available" and when fed into the Read Single Point.vi of this driver it results in a full blown time out error message. I thought that other drivers were supposed to pass these types of warnings through without any ill effects? I found a workaround by erasing this specific warning message but was wondering if this is expected behavior? See attached with default warning message sent in. 
    Using LabVIEW 2010SP1 and TestStand 4.5
    Attachments:
    34401FailWarning.vi ‏17 KB

    NathanT,
     The Precon driver I am using is located here. I'm still confused as to why a warning flag coming in on the error input should cause the 34401 driver to fail. This same warning flag/error line is sent through this driver without any ill effects. I thought that a warning would just be passed through as it really isn't an error?
    Using LabVIEW 2010SP1 and TestStand 4.5

  • Agilent 33220A (Function Generator) .. To Turn ON DC output

    hi ,
    Iam using the 33220A ,Agilent function generator ..with labview 8.5 ..
    I need the control or Subvi that will output a DC .. i.e on the agilent ..Utility->DC off/On .. i need to activate the DC ON ...with a particular Dc offset voltage ..
    Iam unable to find a subvi which can do this ..
    Iam currently using the labview driver downloaded from the ni.com.
    Thanks,
    Anwar.

    Have you tried ag33xxx-Config Waveform? One of the waveform shapes available is DC and there is control called Offset.

  • Agilent 53131A LabWindows/CVI device driver showing timeout error

    Hi All,
    I have developed TestStand sequences for Measurements using Agilent 53131A frequency counter instrument. I have developed 2 sequences one using CVI drivers and the other using LabVIEW drivers. The functionality of the sequence is as follows
    1. Initialize the instrument
    2. Measure the frequency for N number of times
    3. Close the instrument
    What I could find is the LabVIEW driver based sequence is working fine (for any number of measurements) but the CVI driver based sequence is showing Timeout errors after 1or 2 measurements.
    Thsi is the driver page http://sine.ni.com/apps/utf8/niid_web_display.model_page?p_model_id=1003 
    Can anyone help me to find the root cause of this issue?
    Thanks in advance...
    Into the pursuit...
    Maverick

    Were you using the VXI Plug and Play or IVI driver?

  • Dso1022a (LabVIEW 7.1 driver?)

    Please let me know if my driver can be converted for use with LabVIEW 7.1.
    Thank You.
    Instrument - Agilent DSO1022A Oscilloscope (USB connection)
    Source driver written for LabVIEW 8.2
    Request resulting driver compatible with LabVIEW 7.1
    Solved!
    Go to Solution.
    Attachments:
    agilent_dso1000_series.zip ‏784 KB

    try the attached
    Attachments:
    Agilent DSO1000 Series 7.1.zip ‏687 KB

  • Asio driver for labview / free asio4all driver tia sal22

    Greetings All
    I'm using labview 8.6.1 and would like to use my asio drivers with labview is this possible?  I've installed asio4all http://www.asio4all.com/  hoping that it would show up as another device to choose from but wishful thinking.  
    Does anyone know how I can get the free asio4all drivers to work with labview 8.6.1
    ti sal22

    Although I have no experience with that driver, my guess would be that if there's anything available, it's through ActiveX calls or a DLL. 
    If it does have ActiveX methods availabe, you will use an Automation Open function with ActiveX invoke nodes to make the calls.  If it has a DLL associated with it, look at the Call Library Function Node.  To use this you will need documentation on the functions so that you can specify the appropriate parameters and return values.
    Alex Person
    NI-RIO Product Support Engineer
    National Instruments

  • Is it possible to convert a LabView .ldd Instrument Driver into a dll that can be used with MAX and visual basic?

    I got the following problem. I'm using a Stanford DS360 UltraLow Destortion Function Generator, and would like to access it with the CwIVIFgen ActiveX Controll. In the driver database i found a instrument driver for LabView (ds360fg.llb). But its a llb file and i am not sure what to do.
    Is it possible to convert it?
    Is it possible to use it anyways?
    Maybe i overread the answer, but i search the forums for quite a while now and i am not a bit wiser.
    Thanks in advance
    Felix

    If you have LabVIEW and the application builder, a dll can be created from it but it cannot be used as an IVI driver. The only way to create an IVI instrument driver is with LabWindows/CVI. I personally don't have the time right now to create the dll but maybe if you post to the LabVIEW forum and get someone there to do it. Another other option is to hire an Alliance member to create either a dll from the LabVIEW code or to create an IVI driver from scratch.

  • Labview 5.1 driver for HP3437A

    Hi,
    does anyone have a driver for a HP3437A for labview 5.1?
    On the ni homepage are only drivers for labview 6.0 and 7.0 available.
    Thanks, Niko

    Here it is. Not much of a driver - only one VI and there's no error checking.
    Attachments:
    hp3437a.zip ‏32 KB

  • LabView 2010 - CVI Driver Import Wizard

    I have previously downloaded and used the driver import wizard to create LabView VIs from a CVI driver. Specifically with Labview 8.x and 2009.
    However the latest version of the wizard (v1.3) will not install with LabView 2010 and there isn't a newer one to download w- So the question is, does anyone know if there is an intention to update this wizard so I can use it with LV 2010 ?
    Thanks

    Hi,
    I am having the same problem. Please let me know if this has been resolved yet.
    I tried copying the following directories to labview 2010:
    from     C:\Program Files\National Instruments\LabVIEW 2009\resource\CVIFpConv
    to          C:\Program Files\National Instruments\LabVIEW 2010\resource\CVIFpConv
    and
    from     C:\Program Files\National Instruments\LabVIEW 2009\project\_DriverCtoLV
    to         C:\Program Files\National Instruments\LabVIEW 2010\project\_DriverCtoLV
    and the wizard loads and runs until I specify a .fp file and then I get the error in the jpeg attached. When I try to open the block diagram (FC_RFL_Initialize.vi), it says you need a password to view it, so that stops my debugging.
    Attachments:
    Error using Instrument Driver Import Wizard in LabView 2010.JPG ‏88 KB

Maybe you are looking for

  • Just installed acrobat pro11 & it crashes when trying to open

    I just signed up to this prig and after installing it wont open.  crashes straight away.  i had already downloaded the trial version and it worked fine.  i have restarted my computer but this didnt help.  im using macbook pro

  • Hdmi input via thunderbolt 2

    Hi all and thanks for your help in advance. Iv been doing a bit of trawling on the internet try to find out if you could use a late 2013 15"MacBook Pro as a monitor. Essentially to plug in my xbox one while my other half is watching telly. the intern

  • Partner function not copied from notification to order

    hi   i am using same partner determination procedure for notification and service order. i have defined some new partner functions in the procedure. the problem i'm facing is that only the partner functions which are made mandatory are getting copied

  • Open website alias in non-default browser

    I have Firefox set as my default browser. I want to set up an alias on my machine to go to a website, but so it will open in Chrome for just that alias. Can you do that on Macs?

  • Reports3.0 to Excel

    Hi All, It is possible to convert a report 3.0 into excel using DELIMITED? Whether it will support? and also one more problem, pls have a look below coding... Procedure Setwdith(p_col number, p_width number) is Begin v_lst := ole2.create_arglist; ole