Agilent 53230A: +320, 0xbfff0015, 0xbfff0030 user abort errors?
While testing out my code, everytime I set sample count higher than 1 it keeps returning 0xbfff0030 user abort errors, and the measured data doesn't get transferred. Occasionally (haven't been able to duplicate the errors exactly) it also returns "Instrument reports:+320,"Input signal frequency shift caused internal counter overflow" and "hex 0xbfff0015" errors. Is there something wrong with my code? Should I use a while loop to get multiple/continuous data instead of using a higher sample count?
The instrument also shows "error caused by remote command".
I've attached the block diagram image for my code. Thanks again for any help!
Attachments:
draft2.GIF 18 KB
Hi, thank you for your reply!
I'm trying to compare 2 channels so it's supposed to export out the frequency ratio between the 2 channel inputs.
It's actually the Read Measurement VI that's throwing up the errors:
Possible reason(s):
Instrument reports:
+320,"Input signal frequency shift caused internal counter overflow"
+0,"No error"
Complete call chain:
Agilent 532XX Series.lvlib:Error Query.vi
Agilent 532XX Series.lvlib:Read Measurement (Multiple).vi
draft 4a.vi
and
Error -1073807339 occurred at VISA Read in Agilent 532XX Series.lvlib:Wait for Acquisition Complete.vi->Agilent 532XX Series.lvlib:Read Measurement (Multiple).vi->draft 4a.vi
The most readings it's been able to export out is 2 readings, and still gives an error. Anything more and it just exports out a blank report (other than the header). I took all the VI from the Agilent driver pages, and all values have been left at the defaults. I've tried using the Fetch Measurement VI before the Read Measurement but it just makes the program run indefinitely (only way to stop it was to save the VI). Did I screw up the order of the subVIs in my program? Right now it's [Initialize -> Configure Measurement Freq Ratio -> Configure Freq Gate -> Configure Gate Start -> Configure Gate Stop ->Configure Sample Count -> Read Measurement -> Close -> Error Query]. I pretty much used the examples VIs in the drivers I downloaded as a base so if I screwed up anything please let me know.
Also, right now it looks like the VI is exporting values at one second intervals. Is it possible to make it such that it can read values at intervals other than one second (shorter or longer), preferably user-defined?
Again, thanks a lot for taking the time to help out.
Similar Messages
-
Hello,
I am getting 'Thread was being aborted - Unable to evaluate expression because
the code is optimized or a native frame is on top of the call stack' error
when I use 'SPUtility.GetPrincipalsInGroup' method.
bool bReachedMaxCount = false;
SPPrincipalInfo[] _spPrincInfoColl = SPUtility.GetPrincipalsInGroup(web, groupName, Int32.MaxValue - 1, out bReachedMaxCount);
We have both SharePoint groups (SPGroup) & Active Directory groups in our site.
I am checking if logged in user has access to the group name that I am passing here as 'groupName'.
Code works without any error when I pass 'domain name' as 'groupName' e.g. (Domain\\usergroup) but the same throws error when I pass SharePoint groups (SPGroup) name.
Both type of these groups have at least 'Read' permission on site.
I have this code inside 'try-catch' block and hence I am able to catch that thread aborted error.
What could be the reason for this error? I don't get any call stack and all other properties of exception object are either null or with garbage values.
I am having SP2010 foundation, VS2012 and .Net4.5 installed on my machine.
Kindly suggest on this. Thank you.
Sagar S.I think the RunWithElevatedPrivilages is not working correctly. I believe that the new site and web objects need to be opened within elevatedprivilages to work. it looks like the way your code is working the SPsite and SPweb objects are getting opened before
the RunWithElevatedPrivilages give this a try and see if your result changes.
bool IsUserInGroup = false;
try
SPSecurity.RunWithElevatedPrivileges(() =>
Guid siteId = SPContext.Current.Site.ID;
Guid webId = SPContext.Current.Web.ID;
using (SPSite newSite = new SPSite(siteId)) {
using (SPWeb newWeb = newSite.OpenWeb(webId)){
bool bReachedMaxCount = false;
SPPrincipalInfo[] _spPrincInfoColl = SPUtility.GetPrincipalsInGroup(newWeb, "TestGroup", Int32.MaxValue - 1, out bReachedMaxCount);
if (_spPrincInfoColl.Where(a => a.LoginName == username).Count() > 0)
IsUserInGroup = true;
}//close web
}//close site
catch (Exception ex)
LogManager.LogMessage(ex.Message.ToString());
Alex -
FCP to Compressor meltdown: What does "User aborted Media Server" mean??
"Final Cut Pro generated an error or unexpectedly quit User aborted Media Server"
That's what I get every time I try to export an MPEG-2 from FCP via a Compressor QuickCluster. Always worked in the past, never works now. I don't recall changing anything. Anybody ever seen this before?I FOUND A SOLUTION TO THIS PROBLEM.
I followed Apple's troubleshooting article: http://docs.info.apple.com/article.html?artnum=302845
And the last step finally fixed the issue. That is, manually uninstall all Compressor and Qmaster application files and reinstall Compressor and Qmaster from the FCS2 discs. Then run Pro App updates. Everything is running smoothly now.
This process does however introduce a new bug in Motion, but I found a way to fix it here:
http://discussions.apple.com/message.jspa?messageID=5258046#5258046 -
How do you use user defined error messages in Value Help?
Hi,
I'm currently working on a Modifiable Value Help Selector in Web Dynpro Java, and I want to use a user defined error message when I validate the values entered by a user. Currently, it's returning its default error message ("Character <string> does not match...").
Since the project requires a different error message, is there a way to override the default error message and use my defined error message instead?
Thanks!Hi Angelo,
I am not sure why message area is showing both Custom and inbuilt messages but you can try the following:
i guess you must be using reportContextAttribute exception for showing Error messages on the input fields as well.in that case you can disable the message area so messages will appear only on the Context level ie; on input fields.
For other messages apart from validation messages you can enable the message area before reporting the exception.
make sure the boolean context variable which will be used for enabling and disabling the message area should have Readonly property set as true.
I am not sure whether this is the only solution for this but you can try and see if it works.
Siddharth -
Error while saving record "User:johndoe": Error -14071
I have added my augmented users from the AD server. When I select user and to apply a setting under Preferences I get this on attempting an "Apply", Error while saving record "User:johndoe":Error -14071. I'm authenticating to my LDAP not AD/All Domains.
I have the server bound correctly to the AD server. Bound to AD, then promoted to OD master.
Tried WGM from another Mac, same error.
I recall my AD admin extending the ad schema last year for OS X 10.4.
Thoughts? Thanks.Thanks David and Mabel, and all for the suggestions. I did go through "Leveraging Active..." prior to posting. I did try your method of canceling the authorization to WGM and viewing Directories. I would select a user from this method and try to apply something from MCX, but still got the -14070 error. Yes, I do have my client bound 1st OD, 2nd AD, with OD first on the search policy for the client.
I though I had solved my issue by authenticating to WGM and LDAP. Then selecting Groups and the Members tab, I define an OD group and select that group. I can then click the "+" towards the right of the window. Then select my AD there which populates. I can add my AD groups or single users to my OD group. Then I'm able to apply MCX settings. But, no "blue" circle next to the group's silhouette. How is my method possibly incorrect?
Also, at some point I unbound my client from AD and it seems the client is ok with getting AD info off my OD server. Example, my AD sharepoint mounts for PHD.
But, I do have a pause of 20 secs. are more when logging into the client as well as accessing applications. Side effect of my method? -
"Invalid User ID" error while running OSoft Application in browser
Hi,
I have installed BPC 7.5 SP04 in Multi Server environment where SQL Server, OLAP Server, Reporting Server on one machine and Application Server and Web Server on other machine, After installing I tried to run Osoft application via url "http://Application Server name/OSoft" as suggested in Install guide but receiving "Invalid User ID" error
Error Information
Server Error in '/OSoft' Application.
Invalid UserID
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Exception: Invalid UserID
Please guide me on this as what can be the cause of this error and how to fix it.
I have used Windows Server 2008 with IIS 7.
Thanks,
Rohit
Edited by: Khatak Rohit on Mar 18, 2011 10:57 AMFirst login must be done with Installation user.
In your case you tried to login from your PC where you were conected with your user.
This user is used to connect to BPC and this user has no rights into BPC.
It was used this user because BPC allow Windows authentication.
So you have to go into IE - Tools - Internet Options
Select Security Tab - Select Intranet
Push Custom Level
Go to section - User Authentication - select "Prompt always user and pwd"
Close IE
Open again and try http://nameofserver/osoft you will receive now a prompt for user and pwd.
Input an user and pwd with access to BPC and you will see this time the page will be load correct.
Regards
Sorin Radulescu -
Attribute for user contains errors. Inform system admin
Hello,
We've got an issue with shopping carts created by a user that was deleted from system. When trying to see in Monitoring Shopping Carts header or item details of a given sc. A web error occurs:
The URL http://srp.srm.gruposalinas.com.mx:8000/sap/bc/gui/sap/its/bbpsc11/! was not called due to an error.
Note
The following error text was processed in the system SRP : Attribute for user contains errors. Inform system admin.
The error occurred on the application server srm-pro_SRP_00 and in the work process 2 .
The termination type was: TH_RES_FREE
The ABAP call stack was:
Form: OUTPUT_EXPRESS_MESSAGES of program SAPLBBP_SC_UI_ITS
Form: EXTERNAL_SCREEN_DETERMINE of program SAPLBBP_SC_UI_ITS
Module: EXTERNAL_SCREEN_DETERMINE of program SAPLBBP_SC_UI_ITS
We've cheked SAP NOTE 312058-BBPPU99: Error: Attribute for ... is missing. Inform ...
But it seems that none of the information applies to us, since this issue is only present for Shopping carts that were created by this deleted user.
So we tried to re-assing one of this sc, chaning PARTNER_NO,ADDR_NR
ADDR NP data in table CRMD_PARTNER according to a new given user, but it didn't work. So we need to know how to re-assing this sc or perhaps how to find what specific attribute is missing.
Any advice is welcome.
Thanks in advance.Hi
<b>Which SRM version are you using ? This is an SRM error message.</b>
The manager role should be enough to change user attribute. The transaction is BBPATTRMAINT. Employee role should have BBPUM02 or BBPAT05 to change their own attribute.
<u>Please check whether the User ID you are using to Log into BBP_PD (and seems to be assigned in the org structure also)is consistent and has no errors in tcode USERS_GEN. You should check the user, it's not set up properly in USERS_GEN Transaction, Else repair the user.
To maintain the user attributes you must have the Administrator role.. Your user should have role SAP_BBP-STAL_ADMINISTRATOR and be integrated in the org structure. your user must be integrated in SRM organizational structure. To see which attributes are missing, you can click on the user in PPOMA_BBP to see details, and go to last tab "Check". This will list all required attributes depending on used scenarios (so you may not require all of them). You can also use transaction BBP_ATTR_CHECK to check user's attributes for a particular scenario.</u>
<b>Please go through the following links as well -></b>
bbp_mon_sc attributes
Re: FM for attribute's value assignation in PPOMA ?
Note 751022 - Monitor Shopping Cart: Item deletion causes termination
Re: User Settings are not saved
Re: Not able to generate user users_gen
Re: SRM organization plan...
Re: User creation error
<u>Hope this will definitely help. Do let me know.</u>
Regards
- Atul -
Can we set the Option "Show add-in user interface errors" with VBA?
Does anyone know if the advanced Option "Show add-in user interface errors" can be set with VBA in Project Pro 2013?
\Spiro Theopoulos, Montreal, QC (Canada)Spiro,
Sorry but as far as I know that option is not available through VBA.
John -
CE 7.2 NWDS wdp ws client user authentication error
Hello CE 7.2 experts !
I am running a CE 7.2 sp 01 env with NWDS. In my landscape I have some webservices running on PI 7.1.
I am trying to develop a webdynpro webservice client. When run gets user authentication errors.
I have configured the Service Groups, provider systems, http destinations etc for this webservice.
After I have successfully build and deployed the wdp app I am getting error on the wdp gui screen like this:
Exception on execution of web service with WSDL URL 'http://xxxxxxx.lxx.xxxx.xxx:50000/dir/wsdl?p=sa/595aaad7bedb3cf89546e4651ea9954d' with operation 'GetBudgetRequest_out' in interface 'GetBudgetRequest_out'
And in log trace:
Invalid Response code (401). Server <http://xxxxxxx.lxx.xxxx.xxx:50000/XISOAPAdapter/MessageServlet?senderParty=&senderService=SLF&receiverParty=&receiverService=&interface=GetBudgetRequest_out&interfaceNamespace=http%3A%2F%2Fsfso.no%2Fagresso%2Fslf> returned message <Unauthorized>. Http proxy info: none
[EXCEPTION]
com.sap.engine.services.webservices.espbase.client.bindings.exceptions.TransportBindingException: Invalid Response code (401). Server <http://xxxxxxx.lxx.xxxx.xxx:50000/XISOAPAdapter/MessageServlet?senderParty=&senderService=SLF&receiverParty=&receiverService=&interface=GetBudgetRequest_out&interfaceNamespace=http%3A%2F%2Fsfso.no%2Fagresso%2Fslf> returned message <Unauthorized>. Http proxy info: none
at com.sap.engine.services.webservices.espbase.client.bindings.impl.SOAPTransportBinding.handleSOAPResponseMessage(SOAPTransportBinding.java:561)
at com.sap.engine.services.webservices.espbase.client.bindings.impl.SOAPTransportBinding.call_SOAP(SOAPTransportBinding.java:1316)
at com.sap.engine.services.webservices.espbase.client.bindings.impl.SOAPTransportBinding.callWOLogging(SOAPTransportBinding.java:952)
at com.sap.engine.services.webservices.espbase.client.bindings.impl.SOAPTransportBinding.call(SOAPTransportBinding.java:907)
at com.sap.engine.services.webservices.espbase.client.dynamic.impl.DInterfaceInvokerImpl.invokeOperation(DInterfaceInvokerImpl.java:76)
at com.sap.tc.webdynpro.model.webservice.model.WSGenericModelClassExecutable.execute(WSGenericModelClassExecutable.java:73)
at com.sap.tc.webdynpro.model.webservice.gci.WSTypedModelClassExecutable.execute(WSTypedModelClassExecutable.java:49)
at com.sap.demo.wd_slf_proj.wd.comp.slf_getbalancecomp.SLF_GetBalanceCustom.executeRequest_GetBudgetRequest_Out(SLF_GetBalanceCustom.java:189)
at com.sap.demo.wd_slf_proj.wd.comp.slf_getbalancecomp.wdp.InternalSLF_GetBalanceCustom.executeRequest_GetBudgetRequest_Out(InternalSLF_GetBalanceCustom.java:153)
at com.sap.demo.wd_slf_proj.wd.comp.slf_getbalancecomp.SLF_GetBalanceCompView.onActionSendReq(SLF_GetBalanceCompView.java:187)
at com.sap.demo.wd_slf_proj.wd.comp.slf_getbalancecomp.wdp.InternalSLF_GetBalanceCompView.wdInvokeEventHandler(InternalSLF_GetBalanceCompView.java:165)
at com.sap.tc.webdynpro.progmodel.generation.DelegatingView.invokeEventHandler(DelegatingView.java:142)
at com.sap.tc.webdynpro.progmodel.controller.Action.fire(Action.java:75)
at com.sap.tc.webdynpro.clientserver.phases.ProcessingEventPhase.doHandleActionEvent(ProcessingEventPhase.java:159)
at com.sap.tc.webdynpro.clientserver.phases.ProcessingEventPhase.execute(ProcessingEventPhase.java:94)
at com.sap.tc.webdynpro.clientserver.window.WindowPhaseModel.processRequestPartly(WindowPhaseModel.java:162)
at com.sap.tc.webdynpro.clientserver.window.WindowPhaseModel.doProcessRequest(WindowPhaseModel.java:110)
at com.sap.tc.webdynpro.clientserver.window.WindowPhaseModel.processRequest(WindowPhaseModel.java:97)
at com.sap.tc.webdynpro.clientserver.window.WebDynproWindow.processRequest(WebDynproWindow.java:514)
at com.sap.tc.webdynpro.clientserver.cal.AbstractClient.executeTasks(AbstractClient.java:55)
at com.sap.tc.webdynpro.clientserver.cal.ClientApplication.doExecute(ClientApplication.java:1652)
at com.sap.tc.webdynpro.clientserver.cal.ClientApplication.doProcessing(ClientApplication.java:1466)
at com.sap.tc.webdynpro.clientserver.session.ApplicationSession.doApplicationProcessingStandalone(ApplicationSession.java:884)
at com.sap.tc.webdynpro.clientserver.session.ApplicationSession.doApplicationProcessing(ApplicationSession.java:856)
at com.sap.tc.webdynpro.clientserver.session.ApplicationSession.doProcessing(ApplicationSession.java:343)
at com.sap.tc.webdynpro.clientserver.session.RequestManager.doProcessing(RequestManager.java:315)
at com.sap.tc.webdynpro.serverimpl.core.AbstractDispatcherServlet.doContent(AbstractDispatcherServlet.java:87)
at com.sap.tc.webdynpro.serverimpl.wdc.DispatcherServlet.doContent(DispatcherServlet.java:76)
at com.sap.tc.webdynpro.serverimpl.core.AbstractDispatcherServlet.doPost(AbstractDispatcherServlet.java:62)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:727)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:820)
at com.sap.engine.services.servlets_jsp.server.Invokable.invoke(Invokable.java:152)
at com.sap.engine.services.servlets_jsp.server.Invokable.invoke(Invokable.java:38)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:400)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:203)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:438)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:427)
at com.sap.engine.services.servlets_jsp.filters.DSRWebContainerFilter.process(DSRWebContainerFilter.java:38)
at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
at com.sap.engine.services.servlets_jsp.filters.ServletSelector.process(ServletSelector.java:80)
at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
at com.sap.engine.services.servlets_jsp.filters.ApplicationSelector.process(ApplicationSelector.java:268)
at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
at com.sap.engine.services.httpserver.filters.WebContainerInvoker.process(WebContainerInvoker.java:81)
at com.sap.engine.services.httpserver.chain.HostFilter.process(HostFilter.java:9)
at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
at com.sap.engine.services.httpserver.filters.ResponseLogWriter.process(ResponseLogWriter.java:60)
at com.sap.engine.services.httpserver.chain.HostFilter.process(HostFilter.java:9)
at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
at com.sap.engine.services.httpserver.filters.DefineHostFilter.process(DefineHostFilter.java:27)
at com.sap.engine.services.httpserver.chain.ServerFilter.process(ServerFilter.java:12)
at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
at com.sap.engine.services.httpserver.filters.MonitoringFilter.process(MonitoringFilter.java:29)
at com.sap.engine.services.httpserver.chain.ServerFilter.process(ServerFilter.java:12)
at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
at com.sap.engine.services.httpserver.filters.MemoryStatisticFilter.process(MemoryStatisticFilter.java:54)
at com.sap.engine.services.httpserver.chain.ServerFilter.process(ServerFilter.java:12)
at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
at com.sap.engine.services.httpserver.filters.DSRHttpFilter.process(DSRHttpFilter.java:42)
at com.sap.engine.services.httpserver.chain.ServerFilter.process(ServerFilter.java:12)
at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
at com.sap.engine.services.httpserver.server.Processor.chainedRequest(Processor.java:447)
at com.sap.engine.services.httpserver.server.Processor$FCAProcessorThread.process(Processor.java:264)
at com.sap.engine.services.httpserver.server.rcm.RequestProcessorThread.run(RequestProcessorThread.java:56)
at com.sap.engine.core.thread.execution.Executable.run(Executable.java:115)
at com.sap.engine.core.thread.execution.Executable.run(Executable.java:96)
at com.sap.engine.core.thread.execution.CentralExecutor$SingleThread.run(CentralExecutor.java:315)
Any help / hits are appreciated.
Hope to get a prompt solution.
best regards,
Ajeet PhadnisHi,
I hope please upgrade SP01 to SP05.
Please look at these two forums
[forum1|Error executing webservice in BPM; and [forum2|Call to sr.esworkplace fails;
Hope this is help full for u
Regards
Vijay -
Is there a LabView example in the use of user defined error codes?
Specifically, I have a VI that tests four arrays of data against various high/low limits. I have pass/fail outputs for 18 tests. I'd like to combine these into an 'error out' cluster with appropriate error codes and messages, for which I've created an x-errors.txt file.
My first question must be trival - how do I just set the 'status' bit of the error stream to let the general error handler then look up the error desription from the file?
Secondly - I can't find an example of this in the technical resourses, amI missing something?
Thanks,
Mike
Mike Evans
TRW Conekt
N.I. Alliance Member, UK
http://www.Conekt.netThere is no example program. There is extensive help on how to do this. Here's the basics.
1) There are two ways to define user error codes in LV6.1. If you are using LV6.0 or earlier, only one method is possible.
2) The 6.0 method involves wiring arrays of error codes and arrays of error code strings to the General Error Handler.vi. These codes will be used to explain any error code which is undefined in LV's internal error code database. Error codes reserved for users which are guaranteed not to be used by NI are from 5000 to 9999.
3) The 6.1 method allows you to create a specially formatted error code file on disk that will be merged with the LV error code database each time LabVIEW launches. For help on this, go to LV's online help, and in t
he Index tab, type
"user-defined error codes, in text files"
(without the quote marks)
4) If you want to set an error into the error cluster, use the General Error Handler.vi again. Wire your error code value to the Error Code terminal (the leftmost-topmost corner terminal). Wire the name of your VI to the Error Source terminal, and wire "No Dialog" to the Type of Dialog terminal (left-side, near the bottom). The error code cluster that comes out of this VI will either be the error in (if one was set) or a new error code cluster with your error and the status bit set to TRUE.
5) The attached demo is written in LV6.0.
Attachments:
Error_Demo.vi 37 KB -
Installing iTunes after registry user permission error
I'm just going to keep this simple. I ran CCleaner and cleaned the registry, then i ran Glary Utilities to clean up whatever CCleaner couldnt. THEN I downloaded iTunes from the apple website. I used winrar and extracted the install into a folder. I removed Bonjour64 from the folder and ran iTunes64. This bypassed Bonjour64 and installed iTunes flawlessly. When when I first opened iTunes it told me Bonjour64 needs to be running in my services...ingore it and continue. Bonjour64 is already running as it wont uninstall from windows when you have the innsufficient user permission error on the registry so its still installed. iTunes opened and I was able to use it as if the error never existed. Hope this helps! (ps after using other peoples tecniques i found that no-one elses worked without reinstalling windows...so I set out for my own solution.)
-ToastHi,
Try diactivating your antivirus software. This seems to work for alot of people. Tell me if this works for you as well.
xxmitchxx90 -
Getting "CONNECT BY loop in user data" error
Hi all,
I used to run the following query but I got this error "CONNECT BY loop in user data"
select * from
bom_details
where common_bill_sequence_id=bill_sequence_id
connect by prior assembly_item_id=component_item_id
Bom_details is one view which contains
SELECT distinct bi1.assembly_item_id, bic.bill_sequence_id, bi1.organization_id,
bi1.common_bill_sequence_id, bic.component_item_id,
bic.component_quantity, bic.item_num
FROM bom_bill_of_materials bi1, bom_inventory_components bic
where bi1.bill_sequence_id = bic.bill_sequence_id
Please advice how to use the query.
Thanks,
KamalHi,
You could try using the NOCYCLE directive to avoid user data errors e.g.
select * from
bom_details
where common_bill_sequence_id=bill_sequence_id
connect by NOCYCLE prior assembly_item_id=component_item_id
Rod West -
User friendly error handling in a trigger
Hello,
How can I have user freindly error handling when am using a trigger??
In the trigger I through an exception such I use if statment in the tigger
If ( condition) then
RAISE_APPLICATION_ERROR(-20001, ' Error message');
end if;How can I display this message in uer friendly way??See Patrick's posts here:
http://www.inside-oracle-apex.com/apex-4-1-error-handling-improvements-part-1/
http://www.inside-oracle-apex.com/apex-4-1-error-handling-improvements-part-2/ -
Page process: user defined error-message
hi to everyone!
i want to display a user-defined error-message, if for example a select in an anonymous PL/SQL block returns more than one row. i tried it with an user defined exception, but i get allways the success message... how can i do that?
thanks for your help.
bye,
christianHi,
In the exception handler of your PL/SQL process use this :-
apex_application.g_print_success_message := '<span style="color:red">Error message</span>';Regards
Paul -
Failed to mount database "General Users". Error: An Active Manager operation failed
Failed to mount database "General Users". Error: An Active Manager operation failed. Error: The database action failed. Error: Database 'General Users' on server 'EX02' cannot be mounted due to a previous error: At '12/3/2014
3:52:17 PM' the Exchange store database 'General Users' copy on this server appears to be inconsistent with the active database copy or is corrupted. For more details about the failure, consult the Event log on the server for other storage and "ExchangeStoreDb"
events. A successful failover restored service. If you have addressed the underlying problem, or if you have decided to attempt to mount the database despite this error, the mount operation may be attempted by using the '-Force' parameter of the Mount-Database
cmdlet. [Database: General Users, Server: EX02.domain.com]
Md. Ramin HossainHi,
From your description, it is recommended to suspend the failed database copy at first using the cmdlet below.
Suspend-MailboxDatabaseCopy -Identity "xxx"
And then reseed the database with a new copy using Update-MailboxDatabaseCopy -Identity "xxx" -DeleteExistingFiles cmdlet.
What's more, here is a helpful thread for your reference.
Update-MailboxDatabaseCopy
http://technet.microsoft.com/en-us/library/dd335201(v=exchg.150).aspx
Hope this can be helpful to you.
Best regards,
Amy Wang
TechNet Community Support
Maybe you are looking for
-
I have 2 iPhones sharing an apple ID (mine and my partner). we have just created separate ID's now that family sharing is available. but the partner's ID wouldn't let her update apps purchased on my ID! Help Please
-
Acrobat Reader x 10.0 - Cannot open pdf as a single file
I am using Acrobat Reader x 10.0 on Win 7 64 bit OS. I save Filemaker 11.0 Reports as PDF Individual Single Files, to a Folder on my Hard Drive. On some occasions, I can have been able to open these Individual Reports files as a Single Files, each of
-
Don't want to right click on a PDF link to save it!!!!
Hi can any one help me to download a .pdf file with out doing save as but just to click on it and it will automatically go to the Save dialog box!!! I have a view document option and a download option on my page and it will be completely useless if t
-
Hello, I am a new user to FormsContral so I may be looking over some things but here's what I've noticed so far... There is no Chinese language support despite it's growing economic importance in the world (and my biz are Chinese clients). There is n
-
JSF: output textfield rendered problem
Hi! In JSF 1.1, in my page when I click the radio button with valuechangelistener brings to the page a text field (rendered = true / false). When I give a value to the text field the value doesn�t go the backing bean field when I go to the next page.