AI Group Config error -10403 when using DAQPad-6070E
I am using a DAQPad-6070E with attached device SCB-68.
Yesterday, I was able to read in analog waveforms using the attached file. Today, without any changes made to the file, I get an error -10403 in AI Group Config.
What could be causing this error since no changes were made in the file or in Measurement and Automation Explorer configuration?
My system configuration is as follows:
Windows XP
Measurement and Automation Explorer v. 2.2.0.3010
NI-DAQ v. 6.9.2f4
LabVIEW v. 6.1
Attachments:
AIGroupConfigError.vi 256 KB
I haven't been able to run your VI since I'm lacking one of the subVIs in your design, but taking a look I have a few suggestions. I noticed that the device and channels controls for AI Config are both hidden on the front panel. The default values for these controls should be checked to make sure that they agree with the device number in MAX. You could place a probe on all of the inputs to the AI Config VI and let us know what values are being sent.
Also, try resetting the device driver through MAX, just in case another program did not release some resources that are needed by your VI.
Similar Messages
-
Error 10403 when using Stand-Alon​e Applicatio​n and DAQPad 6020E
On the computer I have LabVIEW on, I can run my VI and also I can run the stand alone application of that VI. But I can NOT run the stand alone applicaiton of that VI on a 2nd computer with out LabVIEW. I get error # 10403. I belive I build the VI correctly and loaded the proper software/driver because I have found I can run a simple stand alone application VI that does not communicate with my DAQPad 6020E. The second computer does reconize the DAQPad 6020E under the Divice Manager. I tried using differnce divice numbers for the AO and AI...
Hi,
The first thing you need to check is make sure the same DAQ driver is installed on both computers. Then, you need to make sure that you can view the device in the Measurement and Automation Explorer (MAX). Once you can do this, then you will need to make sure the LV Run-Time Engine is installed on the stand-alone comp. This needs to be the same version as LabVIEW that is installed on the computer where the application was developed.
I hope this helps.
George -
AI Group Config Error 10001 using Virtual Channels
In my LabVIEW block diagram, I usually enter in numbers, e.g. 0,1,2 for the channel string input of AI Config. When I try to use a virtual channel, I simply type in the virtual channel, e.g. 0,K Thermocouple,2. However, this causes AI Group Config Error 10001, which applies to an invalid channel string. What is the correct way to enter a virtual channel into the channel string?
Do you have channels with virtual names of "0", and "2"?
If not you may be confusing MAX by using both naming conventions.
Try using only Virtual names.
I generally will use an array of strings where each element is the vitual channel name with no problems.
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction -
Error message when using xrpcc in JWSDP 1_0_01
Dear all,
I've got the following error message when using xrpcc of JWSDP 1_0_01 for my config.xml file.
D:\jwsdp-1_0_01\Message>xrpcc -classpath build -both -d build config.xml
error: invalid element "{http://java.sun.com/jax-rpc-ri/xrpcc-config}configurati
on" in configuration file (line 2)
The content of 'config.xml' is shown as follows.
<?xml version="1.0" encoding="UTF-8"?>
<configuration xmlns="http://java.sun.com/jax-rpc-ri/xrpcc-config">
<rmi name="MessageService"
targetNamespace="http://messageuri.com/wsdl"
typeNamespace="http://messageuri/types">
<service name="MyMessage" packageName="Message">
<interface name="Message.MessageIF"
servantName="Message.MessageImpl"/>
</service>
</rmi>
</configuration>
Thank you for your kind attention!
Regards,
EddieThanks all! I've already solved my previous problem, however, i got another one now.
=========================================================
error: unknown model info in configuration file (line 5)
=========================================================
<?xml version="1.0" encoding="UTF-8"?>
<configuration xmlns="http://java.sun.com/xml/ns/jax-rpc/ri/config">
<rmi name="MessageService"
targetNamespace="http://messageuri.com/wsdl"
typeNamespace="http://messageuri.com/types">
<service name="MyMessage" packageName="Message">
<interface name="Message.MessageIF"
servantName="Message.MessageImpl" />
</service>
</rmi>
</configuration>
Thanks,
Eddie -
ERROR MESSAGE WHEN USING PACK COMMAND Missing file ////presenter.css Command then fails
Also: "This course requires JavaScript to be enabled in your browser. Please enable JavaScript, then relaunch the course." I have Java enabled in all browsers
Thoughts? Using Presenter 10 Win 8.1 Intel I7 new HP with plenty of memory
ThanksI had saved one copy as an .asp but then resaved it to .xhtml
I'm assuming this is a static web site. Rename (F2) all your pages with .html or .htm extension.
.xhtml is not a valid extension.
Nancy O. -
Error message when using search
why do i keep getting an error message when using the "search" tabe in iTunes. This happend whe i upgraded t the latest version of itunes.
Well, I believe JHeadstart does not really have this functionality.
One way is use a Query Operator 'startsWith', but then you always query like LIKE '<entered search value>%'
This is probably not what you want...
But you could hack it into advancedSearch in YourApplicationModuleImpl
try {
if (viewCriterium.getQueryValue() != null) { //This is where exception JHS-00116 is raised...
value = viewCriterium.getQueryValue().toString();
} else {
value = null;
catch (NumberFormatException ex) {
//insert check for wildcard
value = viewCriterium.getValue().toString();
if (value.indexOf('%')>=0) {
sLog.debug("Ja, een wildcard!!!");
operator = "LIKE";
} else {//original exceptionhandling code here...
...and a bit later, add test for "LIKE":
if (viewCriterium.isDate() || viewCriterium.isString() || "LIKE".equals(operator)) {
value = "'" + value + "'";
very nasty code, and does not raise an exception for searches like '%xxx'
Good luck,
HJH
Edited by: HJHorst on Mar 5, 2009 12:03 AM -
Error message when using FM 'BAPI_BUPA_ADDRESS_CHANGE'.
I'm continually getting an error message when using FM 'BAPI_BUPA_ADDRESS_CHANGE'. The message being 'Table BAPIADTEL entry to be changed not found in target system'.
I have looked up this message but all links seem to refer to FM 'BAPI_BUPA_CENTRAL_CHANGE', which I'm not using, and has different parameter settings.
I'm simply trying to update the telephone number and I'm updating strcuture BAPIADTEL and BAPIADTELX but still the message appears. I know that there is a really simple reason for this, but I have been double-checking everything and experimenting with lots of different areas, but with no effect.
Has anyone encountered this problem using the specific FM ''BAPI_BUPA_ADDRESS_CHANGE' ?.
JasonHi Jason,
In case your database tables had already value for field telephone number, then only the flag should be "U".
If the telephone number field was empty, and we will try to change it by using the flag as U, it wont work. In this case, we should be using "I".
I even wrote that before in this post, but somehow I guess the post was locked, and a lot of comments from you and me were not visible apart from the first two. So, I couldnt get any update from you.
Anyway, its good that its working for you. Thank you for the update.
Regards,
Susanta -
Error Message-When using DataScroller
Hi
I get the following error message when using DataScroller. I am using Oracle Jdeveloper 9i production release.
Application Error
Return
Error Message: null
java.lang.NullPointerException
int oracle.jbo.server.ViewRowSetIteratorImpl.scrollRange(int)
int oracle.jbo.server.ViewRowSetImpl.scrollRange(int)
int oracle.jbo.server.ViewObjectImpl.scrollRange(int)
int oracle.jbo.html.jsp.datatags.RowsetNavigateTag.doStartTag()
void DataHandlerComponent.jspService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtime.HttpJsp.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void oracle.jsp.runtimev2.JspPageTable.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse, java.lang.String)
void oracle.jsp.runtimev2.JspServlet.internalService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtimev2.JspServlet.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void javax.servlet.http.HttpServlet.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.invoke(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.include(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.GetParametersRequestDispatcher.include(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.EvermindPageContext.include(java.lang.String)
int oracle.jbo.html.jsp.datatags.ComponentTag.doStartTag()
void Rate.jspService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtime.HttpJsp.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void oracle.jsp.runtimev2.JspPageTable.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse, java.lang.String)
void oracle.jsp.runtimev2.JspServlet.internalService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtimev2.JspServlet.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void javax.servlet.http.HttpServlet.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.invoke(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.include(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.GetParametersRequestDispatcher.include(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.EvermindPageContext.include(java.lang.String)
void BrowseTab.jspService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtime.HttpJsp.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void oracle.jsp.runtimev2.JspPageTable.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse, java.lang.String)
void oracle.jsp.runtimev2.JspServlet.internalService(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void oracle.jsp.runtimev2.JspServlet.service(javax.servlet.http.HttpServletRequest, javax.servlet.http.HttpServletResponse)
void javax.servlet.http.HttpServlet.service(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.invoke(javax.servlet.ServletRequest, javax.servlet.ServletResponse)
void com.evermind.server.http.ServletRequestDispatcher.forwardInternal(javax.servlet.ServletRequest, javax.servlet.http.HttpServletResponse)
boolean com.evermind.server.http.HttpRequestHandler.processRequest(com.evermind.server.ApplicationServerThread, com.evermind.server.http.EvermindHttpServletRequest, com.evermind.server.http.EvermindHttpServletResponse, java.io.InputStream, java.io.OutputStream, boolean)
void com.evermind.server.http.HttpRequestHandler.run(java.lang.Thread)
void com.evermind.util.ThreadPoolThread.run()Issue has been resolved .Ingnore this
-
Adobe Air error message when using PSE 10
When I try using the tips in PSE 10 I get an error message from Adobe Air stating that it is damaged. Have tried uninstalling and re-installing, but that hasn't helped. I have windows 7
Okay Jeff, this is as far as I have gotten so far. I'm using Air version 3.2.0.2070. This is the install log.
Runtime Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -silent -eulaAccepted -programMenu AdobeHelp.air
Installed runtime (2.6.0.19120) located at C:\Program Files (x86)\Common Files\Adobe AIR
Invoking Application Installer for combined install
Launching subprocess with commandline C:\Users\Vette\AppData\Local\Temp\AIRD0CE.tmp\Adobe AIR\Versions\1.0\Adobe AIR Application Installer -runtime C:\Users\Vette\AppData\Local\Temp\AIRD0CE.tmp -silent -withRuntime -url -programMenu -eulaAccepted file:///E:/Adobe%20Photoshop%20Elements%2010/ElementsSTIInstaller/payloads/AdobeHelp/Adob eHelp.air
Application Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -runtime C:\Users\Vette\AppData\Local\Temp\AIRD0CE.tmp -silent -withRuntime -url -programMenu -eulaAccepted file:///E:/Adobe%20Photoshop%20Elements%2010/ElementsSTIInstaller/payloads/AdobeHelp/Adob eHelp.air
Installed runtime (2.6.0.19120) located at C:\Program Files (x86)\Common Files\Adobe AIR
Unpackaging file:///E:/Adobe%20Photoshop%20Elements%2010/ElementsSTIInstaller/payloads/AdobeHelp/Adob eHelp.air to C:\Users\Vette\AppData\Local\Temp\flaE4EA.tmp
Application signature verified
Unpackaging/validation complete
No app located for appID 'chc' and pubID '4875E02D9FB21EE389F73B8D1702B320485DF8CE.1'
Converting unpackaged application to a native installation package in C:\Users\Vette\AppData\Local\Temp\fla71A.tmp
Native installation package creation succeeded
Starting silent combined runtime update and app install.
Updating runtime from version 2.6.0.19120 to version 2.6.0.19140.
Installing app chc.4875E02D9FB21EE389F73B8D1702B320485DF8CE.1 version 3.5.23 to C:\Program Files (x86)\Adobe using the source file at file:///E:/Adobe%20Photoshop%20Elements%2010/ElementsSTIInstaller/payloads/AdobeHelp/Adob eHelp.air
Reinstalling C:\Users\Vette\AppData\Local\Temp\AIRD0CE.tmp\setup.msi
Installing msi at C:\Users\Vette\AppData\Local\Temp\fla71A.tmp\setup.msi with guid {BD7F1DA3-5EA0-65F8-52B0-5E103FDC045A}
Application Installer end with exit code 0
Subprocess app installer succeeded
Runtime Installer end with exit code 0
Runtime Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -silent "E:\Adobe Photoshop Elements 10\AdobePhotoshopDotcomInspirationBrowser.air"
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Invoking Application Installer for combined install
Launching subprocess with commandline C:\Users\Vette\AppData\Local\Temp\AIR4EA4.tmp\Adobe AIR\Versions\1.0\Adobe AIR Application Installer -runtime C:\Users\Vette\AppData\Local\Temp\AIR4EA4.tmp -silent -withRuntime -url file:///E:/Adobe%20Photoshop%20Elements%2010/AdobePhotoshopDotcomInspirationBrowser.air
Application Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -runtime C:\Users\Vette\AppData\Local\Temp\AIR4EA4.tmp -silent -withRuntime -url file:///E:/Adobe%20Photoshop%20Elements%2010/AdobePhotoshopDotcomInspirationBrowser.air
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Unpackaging file:///E:/Adobe%20Photoshop%20Elements%2010/AdobePhotoshopDotcomInspirationBrowser.air to C:\Users\Vette\AppData\Local\Temp\fla634C.tmp
Application signature verified
Unpackaging/validation complete
No app located for appID 'PhotoshopdotcomInspirationBrowser' and pubID '4C35C4D325D350FE0114230CBADCA2DDD0AC8D25.1'
Converting unpackaged application to a native installation package in C:\Users\Vette\AppData\Local\Temp\fla7325.tmp
Native installation package creation succeeded
Starting silent app installation to C:\Program Files (x86)\Adobe. Installing app PhotoshopdotcomInspirationBrowser.4C35C4D325D350FE0114230CBADCA2DDD0AC8D25.1 version 3.07 using the source file at file:///E:/Adobe%20Photoshop%20Elements%2010/AdobePhotoshopDotcomInspirationBrowser.air
Installing msi at C:\Users\Vette\AppData\Local\Temp\fla7325.tmp\setup.msi with guid {4C184855-B85A-6873-C642-60A58682E721}
Application Installer end with exit code 0
Subprocess app installer succeeded
Runtime Installer end with exit code 0
Launching subprocess with commandline C:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -updatecheck
Runtime Installer begin with version 2.6.0.19140 on Windows 7 x86
Commandline is: -updatecheck
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/2.6.0.19140/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/2.6.0.19140/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Unpackaging complete
Download success
Runtime updated downloaded
User has selected immediate install of the update
Starting runtime background update installation
Launching subprocess with commandline C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background\updater -update
Runtime updater successfully launched
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.1.0.4880 on Windows 7 x86
Commandline is: -update
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Relaunching with elevation
Launching subprocess with commandline c:\users\vette\appdata\local\temp\airafa3.tmp\adobe air installer.exe -ei
Runtime Installer begin with version 3.1.0.4880 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_704_0 -ei
Installed runtime (2.6.0.19140) located at C:\Program Files (x86)\Common Files\Adobe AIR
Starting silent runtime update. Updating runtime from version 2.6.0.19140 to version 3.1.0.4880
Installing msi at c:\users\vette\appdata\local\temp\airafa3.tmp\setup.msi with guid {FE23D063-934D-4829-A0D8-00634CE79B4A}
Runtime Installer end with exit code 0
Elevated install completed
Runtime Installer end with exit code 0
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -updatecheck
Runtime Installer begin with version 3.1.0.4880 on Windows 7 x86
Commandline is: -updatecheck
Installed runtime (3.1.0.4880) located at c:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Clearing unused background update directory
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.1.0.4880/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.1.0.4880/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Runtime update not available
Unpackaging cancelled
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.1.0.4880 on Windows 7 x86
Commandline is: -arp:uninstall
Installed runtime (3.1.0.4880) located at c:\Program Files (x86)\Common Files\Adobe AIR
Runtime Installer end with exit code 6
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is:
Installed runtime (3.1.0.4880) located at c:\Program Files (x86)\Common Files\Adobe AIR
Relaunching with elevation
Launching subprocess with commandline c:\users\vette\appdata\local\temp\aire7af.tmp\adobe air installer.exe -ei
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_4784_0 -ei
Installed runtime (3.1.0.4880) located at c:\Program Files (x86)\Common Files\Adobe AIR
Starting silent runtime update. Updating runtime from version 3.1.0.4880 to version 3.2.0.2070
Installing msi at c:\users\vette\appdata\local\temp\aire7af.tmp\setup.msi with guid {47FA2C44-D148-4DBC-AF60-B91934AA4842}
Runtime Installer end with exit code 0
Elevated install completed
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -installupdatecheck
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -installupdatecheck
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Runtime update not available
Unpackaging cancelled
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -arp:uninstall
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Relaunching with elevation
Launching subprocess with commandline c:\program files (x86)\common files\adobe air\versions\1.0\resources\adobe air updater.exe -eu
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_3840_0 -eu
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Starting runtime uninstall. Uninstalling runtime version 3.2.0.2070
Uninstalling product with GUID {47FA2C44-D148-4DBC-AF60-B91934AA4842}
Runtime Installer end with exit code 0
Elevated install completed
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is:
No installed runtime detected
Relaunching with elevation
Launching subprocess with commandline c:\users\vette\appdata\local\temp\airbda4.tmp\adobe air installer.exe -ei
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_764_0 -ei
No installed runtime detected
Starting silent runtime install. Installing runtime version 3.2.0.2070
Installing msi at c:\users\vette\appdata\local\temp\airbda4.tmp\setup.msi with guid {47FA2C44-D148-4DBC-AF60-B91934AA4842}
Runtime Installer end with exit code 0
Elevated install completed
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -installupdatecheck
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -installupdatecheck
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Runtime update not available
Unpackaging cancelled
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is:
No installed runtime detected
Relaunching with elevation
Launching subprocess with commandline c:\users\vette\appdata\local\temp\air2fa8.tmp\adobe air installer.exe -ei
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_5396_0 -ei
No installed runtime detected
Starting silent runtime install. Installing runtime version 3.2.0.2070
Installing msi at c:\users\vette\appdata\local\temp\air2fa8.tmp\setup.msi with guid {47FA2C44-D148-4DBC-AF60-B91934AA4842}
Runtime Installer end with exit code 0
Elevated install completed
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Resources\Adobe AIR Updater -installupdatecheck
Runtime Installer end with exit code 0
Runtime Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -installupdatecheck
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Performing pingback request
Pingback request completed with HTTP status 200
Starting runtime background update check
Begin Background update download from http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update
Unpackaging http://airdownload.adobe.com/air/3/background/windows/x86/patch/3.2.0.2070/update to C:\Users\Vette\AppData\Roaming\Adobe\AIR\Updater\Background
Runtime update not available
Unpackaging cancelled
Runtime Installer end with exit code 0
Application Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -playerVersion=11,2,202,233 -sandboxType=remote -securityDomain=airdownload.adobe.com -https=false -fromUserEvent=true -- -url http://www.adobe.com/support/chc/air/350/AdobeHelp.air -- WWW aHR0cDovL3d3dy5hZG9iZS5jb20vc3VwcG9ydC9jaGMv
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Begin air file download from http://www.adobe.com/support/chc/air/350/AdobeHelp.air
Download destination is C:\Users\Vette\AppData\Local\Temp\fla7A97.tmp
Received download status 200
Response URL is http://www.adobe.com/support/chc/air/350/AdobeHelp.air
Download success
Unpackaging file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp to C:\Users\Vette\AppData\Local\Temp\flaB22B.tmp
Application signature verified
Unpackaging/validation complete
No app located for appID 'chc' and pubID '4875E02D9FB21EE389F73B8D1702B320485DF8CE.1'
Converting unpackaged application to a native installation package in C:\Users\Vette\AppData\Local\Temp\flaC7B.tmp
Native installation package creation succeeded
Starting app installation to C:\Program Files (x86)\Adobe. Installing app chc.4875E02D9FB21EE389F73B8D1702B320485DF8CE.1 version 3.5.23 using the source file at file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp
Got an unexpected fatal error while in stateInstalling: [ErrorEvent type="error" bubbles=false cancelable=false eventPhase=2 text="Unhandled exception Error: Directory can't be written to" errorID=5006]
Launching subprocess with commandline c:\Program Files (x86)\Common Files\Adobe AIR\Versions\1.0\Adobe AIR Application Installer -runtime "c:\Program Files (x86)\Common Files" -silent -logToStdout -url -location "C:\Program Files (x86)\Adobe" -desktopShortcut -programMenu file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp
Relaunching with elevation
Application Installer begin with version 3.2.0.2070 on Windows 7 x86
Commandline is: -stdio
.\pipe\AIR_4952_0 -runtime "c:\Program Files (x86)\Common Files" -silent -logToStdout -url -location "C:\Program Files (x86)\Adobe" -desktopShortcut -programMenu file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp
Installed runtime (3.2.0.2070) located at c:\Program Files (x86)\Common Files\Adobe AIR
Unpackaging file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp to C:\Users\Vette\AppData\Local\Temp\fla3260.tmp
Application signature verified
Unpackaging/validation complete
No app located for appID 'chc' and pubID '4875E02D9FB21EE389F73B8D1702B320485DF8CE.1'
Converting unpackaged application to a native installation package in C:\Users\Vette\AppData\Local\Temp\fla3BF3.tmp
Native installation package creation succeeded
Starting silent app installation to C:\Program Files (x86)\Adobe. Installing app chc.4875E02D9FB21EE389F73B8D1702B320485DF8CE.1 version 3.5.23 using the source file at file:///C:/Users/Vette/AppData/Local/Temp/fla7A97.tmp
Installing msi at C:\Users\Vette\AppData\Local\Temp\fla3BF3.tmp\setup.msi with guid {BD7F1DA3-5EA0-65F8-52B0-5E103FDC045A}
Application Installer end with exit code 0
Elevated install completed
Launching subprocess with commandline C:\Program Files (x86)\Adobe\Adobe Help\Adobe Help.exe
Application Installer end with exit code 0
Date: Thu, 12 Apr 2012 17:10:46 -0600
From: [email protected]
To: [email protected]
Subject: Adobe Air error message when using PSE 10
Re: Adobe Air error message when using PSE 10
created by Jeff A Wright in Downloading, Installing, Setting Up - View the full discussion
Vetteski65 I would recommend reviewing Troubleshoot AIR installation | Windows - http://helpx.adobe.com/air/kb/troubleshoot-air-installation-windows.ht ml for steps on how to resolve your difficulties. Please feel free to respond to this thread if you have any questions about the steps listed within the document. If you could also respond with the specific error message you receive it would be appreciated.
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4331328#4331328
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4331328#4331328. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Downloading, Installing, Setting Up by email or at Adobe Forums
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746. -
Licence error message when using automation software
Error message when using Rational Functional Tester 7.0.1.1
to record a Flex application. The message seemed to come from the
Flex application.
I can record a fiew step in the application, then I have the
message : "Licence are not present. Eith the trial version only
limited record are allowed". But, my license of my Rational
Functional Tester application is activated.
I am using a Flex builder 3 trial version and the trial is
not over.
Is there any problem to get the license in the File compiler
with "D:\apps\IBM\SDP70\FunctionalTester\bin\rft.swc"? That RFT
file is supposed to be included in the flex application once
compileDoes anyone know how to build with automation support in a
linux environment?
We simply run an ant script build and have the SDK installed.
We purchased Flex Builder Professional, but cannot install on Linux
(we don't want to use the alpha version).
Thanks for any pointers :) -
Dreamweaver CC generates one of 3 error messages when using find and replace is used more than twice in succession. "While executing onLoad in bc_afterSave.htm, the following JavaScript error(s) occurred: At line 188 of file C:\Program Files (x86)\Adobe|Adobe DreamweaverCC|Configuration|Shared|BC\JS\bc_sites.js": out of memory"
or
While executing runCommand in File_Save.htm, a JavaScript erroroccurred.
or
While exciting getDynamicContent inAdressURL.htm, a Javascript erroroccirred.
Any thoughts - I end up closing DWCC and reopening. Will work for two additional Find and Replace before the error messaged\s popup again.bkaufman43 wrote:
Thanks Jon. I tried all of those solutions before posting. Same problem. It seems that the problem is tied to DWCC. Do not have the problem when using DW6 on Win8.1. When running DWCC on a Win7 pc, we get the same error message. When running DW6 on Win 7, f&c works fine. It seems to be a bug in DWCC. DWCC works flawlessly on our Macs.
The same steps apply to DWCC, you just need to choose the CC folders rather than the DWCS4-6 versions that the page talks about. The layout of CC's folders hasn't changed from the older versions which is why, I think, Adobe hasn't updated the troubleshooting page as of yet.
As Nancy mentions, a 38,500 page site is sort of ridiculously large for a static website, that could be part of the problem, but your response quoted above leads me to think you may have tried the troubleshooting steps in the wrong version of the program. Could you confirm that? -
My Application gets Error 37 when using Serial Port VIs.
My Application works fine developed with LV 6.1. Then I updated to LV 7.1 and now the Executable of my application gets error 37 when using the old serial port functions. The "serpdrv" file is located in the application directory and is from 02/2002. The application runs well in the development environment after I placed the "serpdrv" file in the LabView directory. I tried to put a line with "serialDevices=..." in the .ini-file of my application but this did not cause an improvement. I also tried to rebuild the EXE with this line in the "labview.ini" file but nothing changes.
Does anybody have another idea ?
Many thanks for help
Thomas>Did you actually replace the old serial functions that come with 7.1 with the functions from 6.1?
Yes. E.g. "open serial driver.vi" uses "open device" with "serpdrv" as device string.
I had the same problem running my application as VI´s. After the copy of serpdrv into the LV 7.1 directory everything works fine.
I don´t understand why the application running as a .exe doesn´t find the serpdrv when it is in the same directory....
Nevertheless many thanks for your answer
Thomas -
I'm getting a error message when using Apple Configurator "unable to send ClearPasscode command to device"
Yes, that is correct. My spreadsheet has the following information in those cells if you want to compare yours on Monday:
Product Type
Application
|
AdamId:
<and a 9 digit number>
I ended up bringing the Macbook Pro home with me after struggling with it for a half hour at the end of a long day. I called and within 5 minutes the problem was corrected. The technician said they were getting calls all day. -
Error 80 when using bluetooth on car radio
error 80 when using bluetooth on pioneer car radio with my iphone 4 and 5
me too...did some digging on the internet and appears Error -80 means the car deck is expecting some bluetooth protocols that your iPhones wont give out. mine was intermittent for last couple years (deck is 12 years old) as of last night i just get error -80 everytime i try to dial out or recieve a call via bluetooth. this issue was intermittent with an iPhone 3G, 4, 4S, 5 and now my current 5S. im blaming Pioneer not Apple for this
I ended up buying a new deck for my car...gets installed tomorrow. -
PCI-6601 - Group Config error -10444 after 9 hours running
We developed a vi in order to acquire from the unique dma channel of the PCI-6601 counter 4 multiplexed inputs for a period measurement. We use the national VI buffered_measured_period_TIO. Each cycle the VI is supplied with one of the 4 input line.
Everything works fine until the 32211 second of measurement (about 9 hours) and after we receive the -10444 error on the group config block and the card freezes (not the software). We need to switch off and on again the PC to start again.
The cycle of measurement is exactly the one from the original Ni Vi and each cycle the reset is performed.
Looking in the database we found a similar problem after a long running (10hours) and a PCI-6602.
We suppose that after s
everal initialization some internal counter goes in overflow (maybe the TAskID counter?).
Does exist any explanation and workouround to solve this?
Is it possible initialize the card only one time for the 4 channel and how?
Regards
Andrea PedeHi Andrea,
What is probably happening is that your memory is becoming increasingly fragmented and after 9 hours there are no continuous blocks of memory available. If you are continuously reconfiguring your counters, that is what is morelikely causing the problem. I included an example that uses all 8 counters and only needs to configure them once. A couple other suggestions:
1) What happens when you create a larger buffer? Can you run the program for longer?
2) Have you tried running a disk defrag program on your memory? One suggestion I found on the net was mem-turbo from a shareware site.
3) What happens if you only use 1 counter? Does the error still occur?
4) Some issues (including error 10444) with the NI-DAQ driver and analog input were solved
by upgrading to NI-DAQ 6.9.3. What is your current computer configuration (software, hardware, driver version etc.)? This might help narrow the problem down.
Simultaneous Buffered-Event Counting on All Eight Counters of the 6602 or 6608 Devices
http://sine.ni.com/apps/we/niepd_web_display.display_epd4?p_guid=B45EACE3DC9F56A4E034080020E74861&p_node=DZ52325&p_source=External
Hope that helps. Have a good day.
Ron
Applications Engineering
National Instruments
Maybe you are looking for
-
Hi At the time of GR the batch no is created automatically.Vendor is one of the characterestic in the batch. How the value for the characterestic 'vendor' can be updated automatically? Regards Soumen
-
Cannot install Flash Player ActiveX plugin
It's very interesting that I am able to install Flash Player for Mozilla but not for IE (ActiveX). As I'm a web site designer, I need to surf my design at different browsers to ensure compatibility. I tried many of solutions (such as uninstaller, res
-
Map MySQL to ArrayCollection in PHP
Hi Guys I have had great success in passing data to flex using Zend AMF as an array of objects and using the result to populate Flex Charts. The problem is I want to use FusionCharts for Flex, this require me to pass an ArrayCollection to the FusionC
-
Hi, Apps: 11.5.10.2 DB: 10.2.04 O/S Windows 2003 Server when accessing the application our forms are getting freezed and not able to close the forms.I have found the following error while accessing the apps from my windows 7 client desktop java.net.S
-
Can't establish connection to Mac 10 X
I have a Palm Vx using a serial dock and a serial to USB conversion cable. I am trying to HotSync with a Mac running OS 10.5.5, with Palm Desktop 4.2.1. When I press the hotsync button on the cradle, a HotSync Progress window opens on the Mac and sho