AIM-CUE Upgrade Error

Hi Guys,
I am having a problem while try to upgrade my aim-cue module version 3.2.4.0 to version 7.0.3.
Thats my logs at down below. I couldn't any proper answer for that. This is for my lab.
Help guys.
mycue> $tall clean url ftp://192.168.1.100/cue-vm-k9.nm-aim.7.0.3.pkg
WARNING:: This command will install the necessary software to
WARNING:: complete a clean install. It is recommended that a backup be done
WARNING:: before installing software.
Would you like to continue? [n]y
Downloading ftp cue-vm-k9.nm-aim.7.0.3.pkg
Bytes downloaded : 182241
Validating package signature ... done
Validating installed manifests ........
Foundation verification failed
Manifest signature validation failed for bootloader_sec_manifest.sig
mycue>

Hi,
Did u verify the MD5 checksum after u downloaded the package ?
it should be 83c78328efcf686968032333b1d922f3
regds,
aman

Similar Messages

AIM-CUE never get up

hi all
i have a new AIM-CUE module that installed in C2811 router.
the problem that the int service-Engine 0/0   protocol never get up as seen below
CME_CUE_LAB#sh int service-Engine 0/0
Service-Engine0/0 is up, line protocol is down
Hardware is I82559FE, address is 58bc.2739.d20a (bia 58bc.2739.d20a)
Interface is unnumbered. Using address of FastEthernet0/0 (10.0.0.1)
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:09, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     67 packets output, 5876 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
the configuration for the interface :
interface Service-Engine0/0
ip unnumbered FastEthernet0/0
service-module ip address 10.0.0.10 255.255.255.0
service-module ip default-gateway 10.0.0.1
end
i really need your help

Hi
Thanks for your reply .
The problem that because the line protocol is down in the interface ,I cannot open a session on it and I cannot see any logs on the AIM-CUE.
Is there any action that I can make it
Also I noticed that upon the AIM daughter board there are 3 pins without any jumper, is it correct ?
Best regards,
Mohamed Ibrahim Omran
Network Section Head
Dialup and VOIP Unit
A11-B90, Smart Village,
KM 28 Cairo-Alex Desert Road,
6 October 12577, Egypt
T: +20 (2) 33 32 0700 | Ext: 1122
F: +20 (2) 33 32 0800 | M: 010-3532153
E: [email protected]
www.tedata.net

AIM-CUE IVR

Hi,
I have a AIM-CUE with a 1GB Flash. When I try to add on a 4 port ivr license, I get the following error message:
Downloading ftp cue-vm-license_4port_ivr_7.0.2.pkg
Bytes downloaded : 3319
Validating package signature ... done
compatibility mode
Validating installed manifests .............complete.
The system will be brought to offline state for a brief period
and will be brought back to online state automatically
No work order produced.
The system is back in online state
55296+0 records in
108+0 records out
ERROR - Hot Installation failed.
I am not sure why the installed failed.
Any help appreciated.
Thanks,
Paul

Hi,
The AIM is in the 2821 router running 12.4 AES T train IOS.
CUE will allow me to installed the zero ivr port package but not the 2 or 4 port.
CUE config :
se-10-2-1-2# show software packages
Installed Packages:
- Installer (Installer application) (7.0.2.0)
- Thirdparty (Service Engine Thirdparty Code) (7.0.2)
- Bootloader (Primary) (Service Engine Bootloader) (2.1.14)
- Infrastructure (Service Engine Infrastructure) (7.0.2)
- Global (Global manifest) (7.0.2)
- Service Engine license (License for the Service Engine) (2.1.2.0)
- Auto Attendant (Service Engine Telephony Infrastructure) (7.0.2)
- Voice Mail (Voicemail application) (7.0.2)
- Bootloader (Secondary) (Service Engine Bootloader) (2.1.14.0)
- Core (Service Engine OS Core) (7.0.2)
- GPL Infrastructure (Service Engine GPL Infrastructure) (7.0.2)
Installed Plug-ins:
- CUE Voicemail Language Support (Languages global pack) (7.0.2)
- CUE Voicemail US English (English language pack) (7.0.2)
se-10-2-1-2# show software licenses
Installed license files:
- voicemail_lic.sig : 25 MAILBOX LICENSE
Core:
- Application mode: CCM
- Total usable system ports: 6
Voicemail/Auto Attendant:
- Max system mailbox capacity time: 840
- Default # of general delivery mailboxes: 10
- Default # of personal mailboxes: 25
- Max # of configurable mailboxes: 35
Interactive Voice Response:
- Max # of IVR sessions: Not Available
Languages:
- Max installed languages: 2
- Max enabled languages: 2

How to load an ios into cisco aim-cue on 2811 router.

Goodday Everyone.
Please I have a Cisco aim-cue module that I want to load an IOS into on my Cisco 2811 Router,initially I thought it will be easy to do since I am used to upgrading Router and switches IOS using tftp server but it is not so.it seem different,I have been on google but I am not getting any joy.
Please can anyone kindly give me the steps I need to fellow to load the IOS on the aim-cue.
Many thanks.
Kaycee

Please check below link, it may be what you are looking for
http://www.cisco.com/en/US/products/sw/voicesw/ps5520/products_tech_note09186a008064172a.shtml
Regards,
Nishant Savalia

Help! Can't open files in all programs since installing version cue upgrade

Please help. A few days ago I got some pop up (I'm in windows XP) saying updates were available for 2 adobe things. I just chose yes and kept working. Now, I can't open files in any of my CS3 programs. I have lost 4 days of productivity and fear losing my mind next!! after doing some research, it appears alot of people are having trouble since uploading some version cue upgrade for cs3. I followed their suggestions and unchecked VC in photoshop (my first offender) and suddenly I could open files again. But now I can't in Illustrator, but in preferences, it does not have VC checked.
I've tried uninstalling and reinstalling the whole package. I've tried just uninstalling VC. Nothing's working and I'm having major deadline problems now.
Please, please help! Thanks.
Anne

You can try a system restore to a point before the update. If you're lucky, it might work, but I often find System Restore will fail when you need it the most.
Peter

AIM/CUE not Picking-up in-bound external calls

I have a 2811 router with an AIM/CUE (12-VM) card. All of the telephony-service stuff works fine:
-All calls in house work fine
-All outbound calls work fine, to PSTN
-All inbound calls work fine, from PSTN
-Each phone can access it's VM internally
-the CME gui and the Unity-Express gui's are accessible on the LAN.
But, when I call from outside into the PRI with a DID number, I get four rings, then a pause, and then it never goes to voicemail. Sometimes; depending if I call with my celr or a land line, I get the message "Sorry your call cannot be completed as dialed, 000-000." Any clue why the vm does work for internal or external calls.
Here's a sample of the config.
interface FastEthernet0/0
no ip address
no ip mroute-cache
duplex full
speed 100
interface FastEthernet0/0.100
description SUB-IF for VOICE VLAN
encapsulation dot1Q 100
ip address 10.1.100.1 255.255.255.0
interface FastEthernet0/0.101
description GW FOR VOICEMAIL MODULE AIM/CUE
encapsulation dot1Q 101
ip address 10.1.101.1 255.255.255.0
interface Service-Engine0/1
discription AIM/CUE VOICEMAIL MODULE
ip unnumbered FastEthernet0/0.101
service-module ip address 10.1.101.2 255.255.255.0
service-module ip default-gateway 10.1.101.1
ip route 10.1.101.2 255.255.255.255 Service-Engin0/1
dial-peer voice 40 voip
description ** cue voicemail pilot **
destination-pattern 6000
session protocol sipv2
session target ipv4:10.1.101.2
dtmf-relay sip-notify
codec g711ulaw
no vad
dial-peer voice 41 voip
description ** cue auto attendant **
destination-pattern 6001
session protocol sipv2
session target ipv4:10.1.101.2
dtmf-relay sip-notify
codec g711ulaw
no vad
dial-peer voice 1 pots
description ** T1 PRI Emergency 911 **
destination-pattern 9911
port 0/0/0:23
forward-digits 3
dial-peer voice 2 pots
description ** T1 PRI OutBnd Calls **
destination-pattern 9T
port 0/0/0:23
dial-peer voice 3 pots
description ** T1 PRI InBnd Calls**
incoming called-number .
direct-inward-dial
port 0/0/0:23

Problem has to do with how many Digits are getting sent to voice mail on the router when it tries to make the call. You should be seeing 10 digits in the debug.
Next question when one ephone calls another ephone locally does voice mail work?
Try the following commands. This will create a translation-rule that will strip incoming 10 digits to the 4 digits you need. I assume you do not need all 10 digits.
voice translation-rule 1
rule 1 /^650$....$/ /\1/
voice translation-profile digitstrip
translate called 1
voice-port 0/0/0:23
translation-profile incoming digitstrip
*************Voice port were you Telco Line comes in Port 0/0/0:23 based on your config*************
telephony-service
no dialplan-pattern 1 6503926... extension-length 4
Ronnie

AIM-CUE module

Hi
I have installed an AIM-CUE into my 2801 router, but there are some files which am not sure which will work with this AIM-CUE which l have installed into the router 2801. These are files that l have and l need an advise concerning these files because l have the nme and the aim files but the device that l have installed into my router 2801 is AIM-CUE. Advice me on which ones to use pls.
Ojay
1 cue-installer.nme.7.0.3
2 cue-vm-installer-k9.nme.7.0.3.prt1
3 cue-vm-k9.nme.7.0.3pkg
4 cue-vm-licence_50mbx_ccm_7.0.3pkg
5 cue-vm-en_US-langpack.nme.7.0.3prt1
6 cue-vm-full-k9.nme.7.0.3.prt1
7 cue-vm-langpack.nme.7.0.3.pkg
8 cue-installer.nm-aim.7.0.3

Hi Ojay,
Here we go
For NM-CUE, NM-CUE-EC, and AIM-CUE (cue-vm-k9.nm-aim.7.0.x.zip)
•cue-installer.nm-aim.7.0.x
•cue-vm-k9.nm-aim.7.0.x.pkg
•cue-vm-full-k9.nm-aim.7.0.x.prt1
•cue-vm-installer-k9.nm-aim.7.0.x.prt1
•cue-vm-langpack.nm-aim.7.0.x.pkg
http://www.cisco.com/en/US/docs/voice_ip_comm/unity_exp/rel7_0/install/boothelp.html#wp1142398
And;
cue-vm-en_US-langpack.nm-aim.7.0.6.prt1
Release Date: 05/OCT/2010
Package payload containing all US English language data and prompt files associated with the Cisco Unity Express with VoiceMail application on the AIM-CUE, NM-CUE, and NM-CUE-EC service modules.
Size: 27537.68 KB (28198577 bytes)
Cheers!
Rob
Please remember to tag your threads and help support "Teachers without Borders"
https://supportforums.cisco.com/community/netpro/idea-center/communityhelpingcommunity

2007 Upgrade Error Company DB not consistent

Hi there,
I am currently using SAP b1 2005 server and client
im using Sql server 2005 for for database
while upgrading the system from 2005 to 2007
every thing(b1 server, client,company database) upgraded succesfully
but while loging into company it is showing error
"The company DB is not consistent, Check the SAP Business One log file for more information [Message 131-219]"
Thank you for your intrest in reading,
if you encountered similar problem or you know the solution please tell the solution
also plz tel where can i find solution for this kind of technical issues...
Thanks & Regards
Radhakrishnan
in the log file the error is like the following
Failed to read threshold from file - ReadThresholdFromFile     C:\Program Files\SAP\SAP Business One\SAP Business One.exe     PID=2828     TID=2180
30/04/2008 20:27:25:452211       Upgrade            Note           Threashold for IRU is 0.050000     C:\Program Files\SAP\SAP Business One\SAP Business One.exe     PID=2828     TID=2180
30/04/2008 20:28:16:635453       Upgrade            Error          FromVersion=680318     ToVersion=860029     UPG_DoObjectUpgradeInt 2, error in object index=276, object name=Japanese Local Era, object ID=275
STACK:
Frame id=00: "C:\Program Files\SAP\SAP Business One\SAP Business One.exe"; base=0x00400000, offset=0x02DF9710
Frame id=01: "C:\Program Files\SAP\SAP Business One\SAP Business One.exe"; base=0x00400000, offset=0x02BCC676
Frame id=02: "C:\Program Files\SAP\SAP Business One\SAP Business One.exe"; base=0x00400000, offset=0x02BCB392
Frame id=03: "C:\Program Files\SAP\SAP Business One\SAP Business One.exe"; base=0x00400000, offset=0x02BCB30D
Frame id=04: "C:\Program Files\SAP\SAP Business One\SAP Business One.exe"; base=0x00400000, offset=0x02BC9344
Frame id=05: "C:\Program Files\SAP\SAP Business One\SAP Business One.exe"; base=0x00400000, offset=0x0257D254
Frame id=06: "C:\Program Files\SAP\SAP Business One\SAP Business One.exe"; base=0x00400000, offset=0x02C3EEB1
Frame id=07: "C:\WINDOWS\system32\kernel32.dll"; base=0x7C800000, offset=0x7C80B50B
     C:\Program Files\SAP\SAP Business One\SAP Business One.exe     PID=2828     TID=2180
30/04/2008 20:25:09:463527       Upgrade            NoteLogAlways     FromVersion=680318     ToVersion=860029     Ending the company upgrade     C:\Program Files\SAP\SAP Business One\SAP Business One.exe     PID=2828     TID=2904

Radhakrishnan,
I ran into a similar problem recently while attempting an upgrade. I didn't find a solution to my specific problem but, I was wondering if you had run the pre-upgrade query. There is a SAP note
1000846 that refers to upgrade issues and the pre-upgrade query I would run this if you haven't already and see if it returns any results.
Also: here is a link to the query directly
[http://service.sap.com/~sapidb/012006153200000918392007E/UpgradeCheckScript_25_2004A_V.txt]
hope this helps,
Lucas

SP 2013 upgrade error on all discussion lists

Has anyone had any issue with discussion lists in the upgrade process? Our client based all sites off the team site template and so most all have a discussion list.
All sites are failing to upgrade on this feature and not sure why. Doesn't seem to be very common problem. Ignore the TimeMaskedControl feature errors, we have resolved those already.
Any thoughts/suggestions are appreciated!

did you run the test spcontent database and what about the output?
Test-SPContentDatabase -Name <DatabaseName> -WebApplication <URL>
do you have data in the discussion list? also if you can share the upgrade error log only, it will be great help.
Please remember to mark your question as answered &Vote helpful,if this solves/helps your problem. ****************************************************************************************** Thanks -WS MCITP(SharePoint 2010, 2013) Blog: http://wscheema.com/blog

Ichat can't connect to my AIM account, gives me the error "Cannot log in to AIM. General error. Try again." Please help!

ichat can't connect to my AIM account, gives me the error "Cannot log in to AIM. General error. Try again." Please help!

HI,
Your specs say OS X 10.6.8 which would be iChat 5.x.x in Snow Leopard.
This version by default tries to login in to the AIM server called login.oscar.aol.com on port 5190 using the TCP protocol.
An internet connection is made up of 65535 of these so called ports (more like TV stations)
Most routers have ports up to port 1024 which means some of the iChat Login Ports are above this.
Two ways to Solve this.
1) Change the Login port iChat uses
2) Change the way the router opens ports.
For 1) go to iChat Menu > Preferences > Accounts
Highlight/select the AIM account.
In the Info Tab deselect the "Enable this Account" to make sure you are Logged out.
In the Server Settings change the Port to 443
You can decide not to use SSL as well if you wish (the server name automatically loses the leading "s")
For 2) log in to the routers set up pages and make sure it is doing UPnP
This allows the computers to tell the router which ports to open. It also allows multiple devices to use the same ports.
For iChat this allows it to Screen Share as this happens on an unlisted random port.
Opps forgot a couple of things.
If you are using an APple ID registed at Apple ending in @mac.com @me.com or @iCloud.com then the passowrd at Apple has to be 16 characters or less to work with the AIM servers.
Additionally the iCloud issued @me.com and @iCloud.com one require you to use iChat 6 in Lion or Messages in Mountian Lion due to changes Apple made to the security of letting AIM "read" the passwords.
9:38 PM Sunday; June 9, 2013
 iMac 2.5Ghz 5i 2011 (Mountain Lion 10.8.4)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad
"Limit the Logs to the Bits above Binary Images."  No, Seriously
Message was edited by: Ralph Johns (UK)

1760V router and AIM-CUE

Does anyone know if the AIM-CUE will work in a 1760 or 1760V router? I know it is not on the compability list but I know sometimes things work where not listed.

Michael,
Sorry but the 1760 range are not in the AIM-CUE compatability matrix.
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/compatibility/cuecomp.html#HardwareAIM
Regards,
Alex.
Please rate useful posts.

Messages can't communicate with the account "AIM." Cannot log in to AIM. General error. Try again

Hi,
For the first time today, I've been having problems connecting to AIM using Messages. I get the "Messages can't communicate with the account "AIM." Cannot log in to AIM. General error. Try again." error. I looked at the forums here and I tried deleting my account, restarting my computer, reinstalling the account but to no avail. I've been using messages and mountain lion for a few weeks and never had a problem with connecting to AIM until now. Any help is greatly appreciated!

uncheck SSL in server settings....done deal. Funny part is I was having the same problem...went to genius bar...they couldnt figure it out...told me to call apple support. Did that...they told me to re install software after an hour of trying to figure it out...that didnt work either.
amazing the info you can get thru forums.!

AIM CUE disk filling up

Hi
We have a few customers with the AIM-CUE (v 2.1.1) in their CME systems. The flash drives in these systems will fill up about every six months requiring someone to boot to the helper and perform a disk cleanup operation (which takes the system down for about 30 minutes).
Voicemail utilization is well under 50% so I'm not sure what is filling up the drive. Trace logging is disabled
I'm wondering if this is working by design. Should the system be cleaning up after itself or do I need to take the system down to perform the cleanup operation on a regular basis?
Thanks

Try this steps
1) Download the helper (installer) image [cue-installer***] from CCO. Put it on tftp.
2) Go to bootloader prompt, change config to point to this helper. Boot this image by
doing a "boot helper".
3) When the image boots up, choose Option 3 to do disk cleanup.
4) Say "y" at the confirmation prompt.
Disk clean up normally just deleting log files and unnecessary system files and compacting
the voiemail database, so it will not delete the voicemail and should not cause the
voicemail lost.

Update AIM-CUE port license count .

Hi,
Yesterday I make migrate license via cisco license portal site to AIM-CUE,
but I make mistake for count of port license 1 (2 port) instead 3 (6 port) ,
how can I update this count of port ? on website it's not able to delete and
re-migrate the license again .
Regards

hi, still have not solved the problem and nobody has answered the question in this forum

AIM-CUE and CCME

Good day, we have a new CCME 3845 Router including VIC2-4FXO,NM-HD-2V,EVM-HD-8FXS/DID,EM-HDA-6FXO modules, this will be used for our new project. Is it possible that the CCME Router will work well on IP Phones even without the AIM-CUE, because that is the only remaining device that need to install on the Router and we want to install now the Router at the Site while we are waiting for the AIM-CUE to arrive the IP Phones should work. Thanks and I will wait for your reply.

Hi Mahmoud,
You should be fine to get started without the AIM-CUE. This will only prevent the setup of the Voicemail potion of the install :)
Cisco CallManager Express/Cisco Unity Express Configuration Example
http://www.cisco.com/en/US/products/sw/voicesw/ps5520/products_configuration_example09186a008037f2a9.shtml
Cisco CallManager Express 3.0 and Later Integration with Cisco Unity Express
http://www.cisco.com/en/US/products/sw/voicesw/ps4625/prod_installation_guide09186a008059fb5f.html
Hope this helps!
Rob

AIM-CUE Upgrade Error

Similar Messages

Maybe you are looking for