AIM server will not respond.
I'm using iChat 5.0.3 and I cannot log-in to my AIM and Jabber accounts, although, I can still log-in to my facebook chat account. I have not enabled my firewall and have tried several different ports and other clients. Please help. Thanks in advance.
I know that AOL is having a problem with some AIM names....
http://discussions.info.apple.com/thread.jspa?threadID=2417383&tstart=0
Similar Messages
-
HT1338 server will not respond when trying to update
The Software Update Server (macupdate.cg.ac.uk) is not responding.
Please help this is the message i get every time i try and update my software now i have an iphone 5 my itunes needs to be updated but it wont because i need the latest software update so i can download the new version of i tunes. I am using Mac OS X 10.6.7 i am running fine on internet and am connected with good broadband speed.
Thanks in advanceYou're saying that there is an issue when trying to use Software Update to get to 10.6.8, correct? An alternate way to apply that update is to download the 10.6.8 update from the Apple download site.
Before running it, bring up Disk Utility, repair permissions, apply the update, and repair permissions again when done. With that, you can now install iTunes 7. -
I originally posted this question to the community section and was advised to post it here. Please bear with me as this will be a long post. I'm including the scenarios involving this reoccurring issue, the trouble shooting steps I've already
taken and the results of several diagnostic tools and logs.
I have a Sony VAIOS VPCEBB33FM lap top since 2011. I have had this issue on an off for a long time. I'm at my wit's end. Any new insights or suggestions would be greatly appreciated.
Scenario Details
1) Some times it's on and off through out the day, sometimes it won't work all day, and once in a while it will work fine for the entire day.
2) I've had this issue across several wireless services, Clear Network accessed with WiMax, Library Wi-fi, Comcast cable internet using wireless router and Wi-fi, and Comcast Xfinity Wi-Fi, to name a few examples.
3) Other devices in the household or library will work with no problems such as my smart phone or my roommates' laptops or desktop computers.
4) Once in a while, the built-in wireless adapter is not found and I have to reinstall the driver. Also the diagnostic tool has had to reset my adapter on an increasing basis.
5) I had my hard drive replaced in December 2014 and my system restored from the System Restore disks that came with it when I bought the laptop. Even though I've been online on an infrequent basis it worked just fine for a while. Now that
I've been online a bit more I'm having the same issues again.
Below are my attempts at trouble shooting so far but I still have not been able to consistently resolve my DNS issues
1) Restarting my adapter
2) Turning off my laptop and removing the power supply for 5-10 minutes before turning it back on.
3) Using the IP Config in Command Prompt
ipconfig /flushdns
ipconfig /registerdns
ipconfig /release
ipconfig /renew
4) Using the NetSh reset in Command Prompt and restarting my laptop
netsh int ip reset c:\resetlog.txt
netsh winsock reset
ipconfig /flushdns
[restart laptop]
5) Configuring the TCP/IP in several settings
Select Internet Protocol Version 4 (TCP/IPv4), and then click Properties.
I have used the following settings:
a) Obtain an DNS server address automatically
b) OpenDNS
208 67 222 222
208 67 220 220
c) Google DNS
8 8 8 8
8 8 4 4
6) Updating the driver for my Intel Centrino(R) Advanced-N 6250 AGN and Intel Centrino(R) WIMAX 6250 from the Intel website previous having my laptop wiped clean in 2014. It still did not resolve the issue. My laptop
manufacturer as not come up with an driver update for my adapter since 2010. I haven't tried to update the adapter driver from Intel's website since having my laptop repaired due to the fact that Intel strongly recommending using the manufacturer's updates
instead and frankly it didn't make much of a difference when I did it the first time.
7) The last one I've tried as of today is going into Services and changing the start up type to automatic for the following:
Computer Browser [changed from manual to automatic]
DHCP Client [already set to automatic]
DNS Client [already set to automatic]
Network Connections [already set to automatic]
Network Location Awareness [changed from manual to automatic]
Remote Procedure Call (RPC) [already set to automatic]
Server [already set to automatic]
TCP/IP Netbios helper [already set to automatic]
Workstation [already set to automatic]
...and I'm still having DNS issues.
My only guessing are that my laptop came with a lemon adapter that needs to be replaced, some advanced setting(s) that I'm not aware off, or my firewall/anti-virus is interfering. I've used Symmantic Anti-virus and Firewall in the past and currently
Avast Anti-Virus with Microsoft Network Firewall. I've had DNS issues with both anti-virus/firewall set ups.
Below are the results from the diagnostics and tests that I've ran.
Windows Network Diagnostics
Your computer appears to be correctly configured, but the device or resource (DNS server) is not responding Detected Detected
Contact your network administrator or Internet service provider (ISP) Completed
Windows can't communicate with the device or resource (DNS server). The computer or service you are trying to reach might be...
Details about network adapter diagnosis:
Network adapter Wireless Network Connection driver information:
Description . . . . . . . . . . : Intel(R) Centrino(R) Advanced-N 6250 AGN
Manufacturer . . . . . . . . . : Intel Corporation
Provider . . . . . . . . . . . : Intel
Version . . . . . . . . . . . : 13.2.1.5
Inf File Name . . . . . . . . . : C:\Windows\INF\oem17.inf
Inf File Date . . . . . . . . . : Monday, June 14, 2010 9:05:44 AM
Section Name . . . . . . . . . : Install_MPCIEX_GEN_6250_AGN_2x2_HMC_WIN7_64_MOW
Hardware ID . . . . . . . . . . : pci\ven_8086&dev_0087&subsys_13018086
Instance Status Flags . . . . . : 0x180200a
Device Manager Status Code . . : 0
IfType . . . . . . . . . . . . : 71
Physical Media Type . . . . . . : 9
Informational Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
Information for connection being diagnosed
Interface GUID: 70a0781d-6329-45e4-8d7c-34aeca294c39
Interface name: Intel(R) Centrino(R) Advanced-N 6250 AGN
Interface type: Native WiFi
Connection incident diagnosed
Auto Configuration ID: 1
Connection ID: 1
Connection status summary
Connection started at: 2015-03-07 19:57:14-186
Profile match: Success
Pre-Association: Success
Association: Success
Security and Authentication: Success
List of visible access point(s): 22 item(s) total, 22 item(s) displayed
BSSID BSS Type PHY Signal(dB) Chnl/freq SSID
60-02-92-C6-D3-E8 Infra <unknown> -62 11 HOME-C7D4-2.4
60-02-92-A1-75-E0 Infra <unknown> -58 6 HOME-B917-2.4
00-1D-D5-D5-34-F0 Infra <unknown> -73 6 HOME-34F2
60-02-92-A1-75-E1 Infra <unknown> -58 6 (Unnamed Network)
06-1D-D5-D5-34-F0 Infra <unknown> -78 6 xfinitywifi
C4-27-95-C9-C4-2D Infra <unknown> -57 1 HOME-C42D
02-1D-D5-D5-34-F0 Infra <unknown> -74 6 (Unnamed Network)
00-0D-97-07-E0-79 Infra g -75 6 (Unnamed Network)
00-1D-CF-2A-44-C0 Infra <unknown> -86 6 HOME-44C2
02-1D-CF-2A-44-C0 Infra <unknown> -86 6 (Unnamed Network)
F8-E4-FB-3C-87-A2 Infra <unknown> -89 6 YVNM7
06-1D-CF-2A-44-C0 Infra <unknown> -87 6 xfinitywifi
0C-F8-93-7A-13-50 Infra b -87 6 PKennedy
06-F8-93-7A-13-50 Infra b -89 6 xfinitywifi
02-F8-93-7A-13-50 Infra b -87 6 (Unnamed Network)
E0-88-5D-C8-A9-DC Infra <unknown> -80 1 HOME-A9DC
E2-88-5D-C8-A9-DD Infra <unknown> -79 1 (Unnamed Network)
16-CF-E2-43-0B-30 Infra <unknown> -88 1 xfinitywifi
60-02-92-F0-A8-C0 Infra <unknown> -90 11 HOME-96A6-2.4
60-02-92-C6-D3-E9 Infra <unknown> -63 11 (Unnamed Network)
02-1D-D4-EB-87-00 Infra <unknown> -88 11 (Unnamed Network)
06-1D-D4-EB-87-00 Infra <unknown> -88 11 xfinitywifi
Connection History
Information for Auto Configuration ID 1
List of visible networks: 13 item(s) total, 13 item(s) displayed
BSS Type PHY Security Signal(RSSI) Compatible SSID
Infra <unknown> Yes 63 Yes HOME-C7D4-2.4
Infra <unknown> Yes 70 Yes HOME-B917-2.4
Infra <unknown> Yes 43 Yes HOME-34F2
Infra <unknown> Yes 70 Yes (Unnamed Network)
Infra <unknown> No 40 Yes xfinitywifi
Infra <unknown> Yes 71 Yes HOME-C42D
Infra g No 43 Yes (Unnamed Network)
Infra <unknown> Yes 28 Yes HOME-44C2
Infra <unknown> Yes 20 Yes YVNM7
Infra b Yes 21 Yes PKennedy
Infra <unknown> Yes 33 Yes HOME-A9DC
Infra <unknown> Yes 35 Yes (Unnamed Network)
Infra <unknown> Yes 16 Yes HOME-96A6-2.4
List of preferred networks: 3 item(s)
Profile: xfinitywifi
SSID: xfinitywifi
SSID length: 11
Connection mode: Infra
Security: No
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: Yes
Profile: HTC Portable Hotspot 9F50
SSID: HTC Portable Hotspot 9F50
SSID length: 25
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: No
Reason: 0x00028002
Profile: belkin.332
SSID: belkin.332
SSID length: 10
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: No
Reason: 0x00028002
Information for Connection ID 1
Connection started at: 2015-03-07 19:57:14-186
Auto Configuration ID: 1
Profile: xfinitywifi
SSID: xfinitywifi
SSID length: 11
Connection mode: Infra
Security: No
Pre-Association and Association
Connectivity settings provided by hardware manufacturer (IHV): No
Security settings provided by hardware manufacturer (IHV): No
Profile matches network requirements: Success
Pre-association status: Success
Association status: Success
Last AP: 06-1d-d5-d5-34-f0
Security and Authentication
Configured security type: Open
Configured encryption type: None
802.1X protocol: No
Key exchange initiated: Yes
Unicast key received: No
Multicast key received: No
Number of security packets received: 0
Number of security packets sent: 0
Security attempt status: Success
Connectivity
Packet statistics
Ndis Rx: 2068
Ndis Tx: 2543
Unicast decrypt success: 0
Multicast decrypt success: 0
Unicast decrypt failure: 0
Multicast decrypt failure: 0
Rx success: 3954
Rx failure: 0
Tx success: 537
Tx failure: 4
Tx retry: 2
Tx multiple retry: 2
Tx max lifetime exceeded: 0
Tx ACK failure: 18
Roaming history: 0 item(s)
InformationalDiagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
For complete information about this session see the wireless connectivity information event.
Helper Class: Auto Configuration
Initialize status: Success
Information for connection being diagnosed
Interface GUID: 70a0781d-6329-45e4-8d7c-34aeca294c39
Interface name: Intel(R) Centrino(R) Advanced-N 6250 AGN
Interface type: Native WiFi
Result of diagnosis: There may be problem
Network Connection details from Command Prompt (some info hidden for security reasons)
Connection-specific DNS Suffix:
Description: Intel(R) Centrino(R) Advanced-N 6250 AGN
Physical Address: 00-23-15-54-19-B8
DHCP Enabled: Yes
IPv4 Address: 192.168.X.XX
IPv4 Subnet Mask: 255.255.XX.X
Lease Obtained: Saturday, March 07, 2015 7:57:14 PM
Lease Expires: Saturday, March 07, 2015 8:24:44 PM
IPv4 Default Gateway: 192.168.X.X
IPv4 DHCP Server: 192.168.X.X
IPv4 DNS Servers: 75.75.75.75, 75.75.76.76
IPv4 WINS Server:
NetBIOS over Tcpip Enabled: Yes
Link-local IPv6 Address: fe80::b8de:3ac9:e166:XXX%XX
IPv6 Default Gateway:
IPv6 DNS Server:
Results of Ping and Trace Route in Command Prompt
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Windows\system32>ping 127.0.0.1
Pinging 127.0.0.1 with 32 bytes of data:
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Ping statistics for 127.0.0.1:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
C:\Windows\system32>ping www.youtube.com
Pinging youtube-ui.l.google.com [173.194.121.6] with 32 bytes of data:
Reply from 173.194.121.6: bytes=32 time=24ms TTL=55
Reply from 173.194.121.6: bytes=32 time=19ms TTL=55
Request timed out.
Request timed out.
Ping statistics for 173.194.121.6:
Packets: Sent = 4, Received = 2, Lost = 2 (50% loss),
Approximate round trip times in milli-seconds:
Minimum = 19ms, Maximum = 24ms, Average = 21ms
C:\Windows\system32>ping 74.125.239.34
Pinging 74.125.239.34 with 32 bytes of data:
Request timed out.
Request timed out.
Reply from 74.125.239.34: bytes=32 time=3286ms TTL=50
Request timed out.
Ping statistics for 74.125.239.34:
Packets: Sent = 4, Received = 1, Lost = 3 (75% loss),
Approximate round trip times in milli-seconds:
Minimum = 3286ms, Maximum = 3286ms, Average = 3286ms
C:\Windows\system32>ping www.hotmail.com
Pinging dispatch.kahuna.glbdns2.microsoft.com [65.55.157.204] with 32 bytes of data:
Reply from 65.55.157.204: bytes=32 time=111ms TTL=237
Request timed out.
Request timed out.
Reply from 65.55.157.204: bytes=32 time=1537ms TTL=237
Ping statistics for 65.55.157.204:
Packets: Sent = 4, Received = 2, Lost = 2 (50% loss),
Approximate round trip times in milli-seconds:
Minimum = 111ms, Maximum = 1537ms, Average = 824ms
C:\Windows\system32>ping 207.46.11.236
Pinging 207.46.11.236 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Ping statistics for 207.46.11.236:
Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),
C:\Windows\system32>tracert www.youtube.com
Tracing route to youtube-ui.l.google.com [173.194.121.5]
over a maximum of 30 hops:
1 19 ms 13 ms 17 ms xfwsr12-nwca-01.sys.comcast.net [68.85.15.244]
2 13 ms 13 ms 27 ms ae-14-32767-ar03.newcastle.de.panjde.comcast.net [68.85.192.205]
3 20 ms 26 ms 21 ms he-5-10-0-0-cr01.ashburn.va.ibone.comcast.net [68.86.94.249]
4 18 ms 34 ms 22 ms he-0-13-0-0-pe07.ashburn.va.ibone.comcast.net [68.86.86.50]
5 19 ms 18 ms 18 ms 50-248-116-190-static.hfc.comcastbusiness.net [50.248.116.190]
6 35 ms 18 ms 18 ms 209.85.249.217
7 21 ms 19 ms 19 ms 72.14.233.93
8 * * * Request timed out.
9 * 2509 ms 677 ms iad23s25-in-f5.1e100.net [173.194.121.5]
Trace complete.
C:\Windows\system32>tracert 74.125.239.34
Tracing route to nuq04s19-in-f2.1e100.net [74.125.239.34]
over a maximum of 30 hops:
1 54 ms 23 ms 12 ms xfwsr12-nwca-01.sys.comcast.net [68.85.15.244]
2 22 ms 19 ms 17 ms ae-14-32767-ar03.newcastle.de.panjde.comcast.net[68.85.192.205]
3 19 ms 19 ms 18 ms he-5-14-0-0-cr01.ashburn.va.ibone.comcast.net [68.86.166.121]
4 18 ms 18 ms 18 ms he-0-15-0-0-cr01.350ecermak.il.ibone.comcast.net[68.86.85.74]
5 19 ms 18 ms 22 ms 50-248-116-190-static.hfc.comcastbusiness.net [50.248.116.190]
6 22 ms 36 ms 19 ms 209.85.249.217
7 26 ms 23 ms 25 ms 209.85.143.112
8 * * * Request timed out.
9 * * * Request timed out.
10 972 ms * * 216.239.51.97
11 148 ms 97 ms 95 ms 216.239.46.241
12 324 ms 130 ms 432 ms 209.85.246.252
13 * * * Request timed out.
14 1403 ms 101 ms 126 ms nuq04s19-in-f2.1e100.net [74.125.239.34]
Trace complete.
C:\Windows\system32>tracert www.hotmail.com
Tracing route to dispatch.kahuna.glbdns2.microsoft.com [65.55.157.144]
over a maximum of 30 hops:
1 13 ms 13 ms 25 ms xfwsr12-nwca-01.sys.comcast.net [68.85.15.244]
2 13 ms 15 ms 13 ms ae-14-32767-ar03.newcastle.de.panjde.comcast.net[68.85.192.205]
3 20 ms 19 ms 17 ms he-5-13-0-0-cr01.ashburn.va.ibone.comcast.net [68.86.95.145]
4 17 ms 20 ms 20 ms he-0-13-0-0-pe07.ashburn.va.ibone.comcast.net [68.86.86.50]
5 17 ms 18 ms 38 ms as8075-2-c.ashburn.va.ibone.comcast.net [173.167.58.82]
6 18 ms 18 ms 36 ms ae4-0.ash-96cbe-1a.ntwk.msn.net [207.46.36.172]
7 * * * Request timed out.
8 * 2191 ms 35 ms ae0-0.atb-96cbe-1b.ntwk.msn.net [191.234.81.167]
9 * * * Request timed out.
10 * * * Request timed out.
11 86 ms 84 ms 84 ms ae4-0.lax-96cbe-1a.ntwk.msn.net [191.234.83.150]
12 86 ms 86 ms 87 ms ae9-0.by2-96c-1a.ntwk.msn.net [207.46.42.176]
13 * * * Request timed out.
14 * * * Request timed out.
15 * * * Request timed out.
16 * * * Request timed out.
17 87 ms 84 ms 85 ms origin.by173w.bay173.mail.live.com [65.55.157.144]
Trace complete.
C:\Users\C.Cunningham>tracert 207.46.11.236
Tracing route to origin.by181w.bay181.mail.live.com [207.46.11.236]
over a maximum of 30 hops:
1 16 ms 16 ms 19 ms xfwsr12-nwca-01.sys.comcast.net [68.85.15.244]
2 18 ms 13 ms 13 ms ae-14-32767-ar03.newcastle.de.panjde.comcast.net[68.85.192.205]
3 21 ms 19 ms 21 ms he-5-12-0-0-cr01.ashburn.va.ibone.comcast.net [68.86.95.141]
4 18 ms 21 ms 18 ms he-0-13-0-0-pe07.ashburn.va.ibone.comcast.net [68.86.86.50]
5 * * * Request timed out.
6 * * * Request timed out.
7 * * * Request timed out.
8 * * * Request timed out.
9 * * * Request timed out.
10 * * * Request timed out.
11 * * * Request timed out.
12 * * * Request timed out.
13 * * * Request timed out.
14 * * * Request timed out.
15 * * * Request timed out.
16 * * * Request timed out.
17 * * * Request timed out.
18 * * * Request timed out.
19 * * * Request timed out.
20 * * * Request timed out.
21 * * * Request timed out.
22 * * * Request timed out.
23 * * * Request timed out.
24 * * * Request timed out.
25 * * * Request timed out.
26 * * * Request timed out.
27 * * * Request timed out.
28 * * * Request timed out.
29 * * * Request timed out.
30 * * * Request timed out.
Trace complete.
Results of Intel WiFi Manual Diagnostics
Test Name Test Result Test Summary
Hardware Test Passed Wireless Hardware is enabled
Driver Test Passed Diver is loaded. NETwNs64 Version 13.3.0.24
Radio Test Passed Radio is ON
Scan Test Passed There are 25 Networks available to connect
Association Test Passed Associated
Authentication Test Passed Authenticated
Signal Test Passed Signal Quality: Poor
Ping Test Failed No Reponse: default gateway, DHCP server
I hope this information is enough to get to the root of this problem once and for all. Please let me know if you any other information such as event logs or statistics.
Thanks in advance.Results of Intel WiFi Event View Log (I deleted some lines since there were basically repeats of the same messages)
#Event Source Time
Error Severity Domain
User Description
45 EvtEngine
3/8/2015 20:40 Success
Connection SYSTEM
iAMT - Failed to read Windows Events Log
46 S24EvMon
3/8/2015 20:41 Information
AppDriver
SYSTEM
Getting List of adapters.
47 S24EvMon
3/8/2015 20:41 Information
AppDriver
SYSTEM
Intel adapter(s) found.
156 S24EvMon
3/8/2015 20:47 Information
Driver SYSTEM
AddToExclude 06:1d:d5:d5:34:f0 xfinitywifi 6 WEV_EXCLUDE_LIST_REASON_802_11_AUTH_FAILURE
157 S24EvMon
3/8/2015 20:47 Information
Driver SYSTEM
ATC 06:1d:cf:2a:44:c0 xfinitywifi 6 RSSI=-88
158 S24EvMon
3/8/2015 20:47 Error
Driver SYSTEM
AssociationFailure 06:1d:cf:2a:44:c0 xfinitywifi 6 CNCT_GENERAL_FAILURE
159 S24EvMon
3/8/2015 20:47 Information
Driver SYSTEM
AddToExclude 06:1d:cf:2a:44:c0 xfinitywifi 6 WEV_EXCLUDE_LIST_REASON_802_11_ASSOC_FAILURE
160 S24EvMon
3/8/2015 20:47 Information
Driver SYSTEM
ATC 06:1d:d5:d5:34:f0 xfinitywifi 6 RSSI=-79
161 S24EvMon
3/8/2015 20:47 Success
Driver SYSTEM
RxAuthSuccess 06:1d:d5:d5:34:f0 6
162 S24EvMon
3/8/2015 20:47 Success
Driver SYSTEM
RxAssocResp 06:1d:d5:d5:34:f0 6 -77
163 S24EvMon
3/8/2015 20:49 Information
TCP/IP SYSTEM
VoIP: Got link down - deleting flows .
164 S24EvMon
3/8/2015 20:49 Information
Driver SYSTEM
ATC 06:1d:d4:eb:87:00 xfinitywifi 11 RSSI=-88
165 S24EvMon
3/8/2015 20:49 Error
Driver SYSTEM
AssociationFailure 06:1d:d4:eb:87:00 xfinitywifi 11 CNCT_GENERAL_FAILURE
166 S24EvMon
3/8/2015 20:49 Information
Driver SYSTEM
AddToExclude 06:1d:d4:eb:87:00 xfinitywifi 11 WEV_EXCLUDE_LIST_REASON_802_11_ASSOC_FAILURE
167 S24EvMon
3/8/2015 20:49 Information
Driver SYSTEM
ATC 06:1d:d4:eb:87:00 xfinitywifi 11 RSSI=-89
168 S24EvMon
3/8/2015 20:49 Error
Driver SYSTEM
AssociationFailure 06:1d:d4:eb:87:00 xfinitywifi 11 CNCT_GENERAL_FAILURE
169 S24EvMon
3/8/2015 20:49 Information
Driver SYSTEM
AddToExclude 06:1d:d4:eb:87:00 xfinitywifi 11 WEV_EXCLUDE_LIST_REASON_802_11_ASSOC_FAILURE
170 S24EvMon
3/8/2015 20:49 Information
Driver SYSTEM
ATC 06:1d:d4:eb:87:00 xfinitywifi 11 RSSI=-90
171 S24EvMon
3/8/2015 20:49 Error
Driver SYSTEM
AssociationFailure 06:1d:d4:eb:87:00 xfinitywifi 11 CNCT_GENERAL_FAILURE
172 S24EvMon
3/8/2015 20:49 Information
Driver SYSTEM
ATC 06:1d:d5:d5:34:f0 xfinitywifi 6 RSSI=-82
173 S24EvMon
3/8/2015 20:49 Success
Driver SYSTEM
RxAuthSuccess 06:1d:d5:d5:34:f0 6
174 S24EvMon
3/8/2015 20:49 Success
Driver SYSTEM
RxAssocResp 06:1d:d5:d5:34:f0 6 -81
175 S24EvMon
3/8/2015 20:50 Information
Driver SYSTEM
AddToExclude 06:1d:d5:d5:34:f0 xfinitywifi 6 WEV_EXCLUDE_LIST_REASON_802_11_AUTH_FAILURE
176 S24EvMon
3/8/2015 20:50 Information
Driver SYSTEM
ATC 06:1d:d5:d5:34:f0 xfinitywifi 6 RSSI=-79
177 S24EvMon
3/8/2015 20:50 Success
Driver SYSTEM
RxAuthSuccess 06:1d:d5:d5:34:f0 6
178 S24EvMon
3/8/2015 20:50 Success
Driver SYSTEM
RxAssocResp 06:1d:d5:d5:34:f0 6 -80
179 S24EvMon
3/8/2015 21:03 Information
Driver SYSTEM
RoamTrigger 06:1d:d5:d5:34:f0 xfinitywifi 6 RSSI=-81 MisBcn=8 RSSITh=-85 Roam Other Reason
186 S24EvMon
3/8/2015 21:21 Information
General
SYSTEM
DeviceIoCtrlS24NDIS: (2) Failed to send OID 0xff100055 to driver. Error - 31
187
S24EvMon
3/8/2015 21:21 Information
General
SYSTEM
DeviceIoCtrlS24NDIS - Dot11ExtNicSpecificExtension failed (31) -
Hi All,
I have the environment like DC1- 2k3 Service Pack 2 which is holding FSMO roles and now I build a new ADC DC2 – 2k8 R2 OS on different location (Subnet) . After completing ADC I run the DCDAIG on DC2 where I am getting below error
Not: I tried the configuration D4 and D2 for Burflag but no luck
Note: DC1 and DC2 both are on different location with different subnet.
Any suggestion or solution please
Doing primary tests
Testing server: indai\DC2
Starting test: Advertising
Warning: DsGetDcName returned information for
\\DC1.test.com, when we were trying to reach
DC2.
SERVER IS NOT RESPONDING or IS NOT CONSIDERED SUITABLE.
......................... DC2 failed test Advertising
Starting test: FrsEvent
There are warning or error events within the last 24 hours after the
SYSVOL has been shared.
Failing SYSVOL replication problems may cause
Group Policy problems.
Starting test: NCSecDesc
Error NT AUTHORITY\ENTERPRISE DOMAIN CONTROLLERS doesn't have
Replicating Directory Changes In Filtered Set
access rights for the naming context:
DC=DomainDnsZones,DC=mh-man,DC=biz
Error NT AUTHORITY\ENTERPRISE DOMAIN CONTROLLERS doesn't have
Replicating Directory Changes In Filtered Set
access rights for the naming context:
DC=ForestDnsZones,DC=mh-man,DC=biz
......................... DC2 failed test NCSecDesc
Starting test: NetLogons
Unable to connect to the NETLOGON share! (\\DC2\netlogon)
[DC2] An net use or LsaPolicy operation failed with error
67, The network name cannot be found..
......................... DC2 failed test NetLogons
Starting test: SystemLog
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 16:40:54
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x00000032
Time Generated: 09/17/2014 16:40:54
Event String:
The time service detected a time difference of greater than 5000 milliseconds for 900 seconds. The time difference might be caused by synchronization with low-accuracy time sources or by suboptimal
network conditions. The time service is no longer synchronized and cannot provide the time to other clients or update the system clock. When a valid time stamp is received from a time service provider, the time service will correct itself.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 16:41:53
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 16:43:06
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 16:45:15
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 16:47:14
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 16:48:22
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 16:49:34
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 16:50:45
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 16:52:55
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
An error event occurred. EventID: 0x00000406
Time Generated: 09/17/2014 16:52:59
Event String:
The processing of Group Policy failed. Windows attempted to retrieve new Group Policy settings for this user or computer. Look in the details tab for error code and description. Windows will
automatically retry this operation at the next refresh cycle. Computers joined to the domain must have proper name resolution and network connectivity to a domain controller for discovery of new Group Policy objects and settings. An event will be logged when
Group Policy is successful.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 16:54:21
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 16:58:35
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 16:59:48
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 17:00:59
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 17:02:11
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 17:03:24
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 17:05:39
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x0000008E
Time Generated: 09/17/2014 17:06:47
Event String:
The time service has stopped advertising as a time source because the local clock is not synchronized.
A warning event occurred. EventID: 0x00000018
Time Generated: 09/17/2014 17:11:36
Event String:
Time Provider NtpClient: No valid response has been received from domain controller DC1.test.com after 8 attempts to contact it. This domain controller will be discarded as a time source and
NtpClient will attempt to discover a new domain controller from which to synchronize. The error was: The peer is unreachable.
......................... DC2 failed test SystemLog
Pradip SisodiyaHello,
please upload the following files so we could understand your setup:
ipconfig /all >c:\ipconfig.log [from each DC/DNS Server]
dcdiag /v /c /d /e /s:dcname >c:\dcdiag.log
repadmin /showrepl dc* /verbose /all /intersite >c:\repl.log ["dc* is a place holder for the starting name of the DCs if they all begin the same (if more then one DC exists)]
dnslint /ad /s "DCipaddress" (http://support.microsoft.com/kb/321045)
ADREPLSTATUS
http://www.microsoft.com/en-us/download/details.aspx?id=30005 can also be exported to file.
As the output will become large, DON'T post them into the thread, please use Windows OneDrive (https://onedrive.live.com) [with open access!]
and add the link from it here. Also the /e in dcdiag scans the complete forest, so better run it on COB.
Best regards
Meinolf Weber
MVP, MCP, MCTS
Microsoft MVP - Directory Services
My Blog: http://blogs.msmvps.com/MWeber
Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
Twitter: -
CLI0615E Error receiving from socket, server is not responding.
We recently changed a web application using DB2 5.2 tables from ODBC to JDBC. We are using the COM.ibm.db2.jdbc.net.driver. We are using a
connection pool and running on iPlanet.
We are getting intermittant "CLI0615E Error receiving from socket, server is not responding errors". We have looked in the JDBC forum and DB2 support and cannot find a reasonable answer to this problem. It is NOT always on sql statements that take a long time to execute, so I don't think it is a timeout issue.
I read something about "stale connections". Does anyone know how to check to see if this is a problem?
When we first converted the app, we had a lot of problems also with "invalid handle or statement is closed" which we have determined was being caused by the user submitting the page again before it had time to finish the first time. We have put in javascript code to prevent multiple submits. Could this server not responding problem be caused by double submits that we have not located yet?
The error is NOT occuring on any one page, and the same page will run correctly once and the next time throw this error.
Any suggestions would be greatly appreciated.
Thanks.
[29/Apr/2003:11:00:20] info (42196): COM.ibm.db2.jdbc.net.DB2Exception: [IBM][JDBC Driver] CLI0615E Error receiving from socket, server is not responding. SQLSTATE=08S01
at COM.ibm.db2.jdbc.net.SQLExceptionGenerator.throwReceiveError(SQLExceptionGenerator.java(Compiled Code))
at COM.ibm.db2.jdbc.net.DB2Request.receive(DB2Request.java(Compiled Code))
at COM.ibm.db2.jdbc.net.DB2Request.sendAndRecv(DB2Request.java(Compiled Code))
at COM.ibm.db2.jdbc.net.DB2RowObject.next(DB2RowObject.java(Compiled Code))
at COM.ibm.db2.jdbc.net.DB2ResultSet.next(DB2ResultSet.java(Compiled Code))
at bom.Bom.getDefs(Bom.java(Compiled Code))
at jsps.bbapps._eng._ENGJGLT0_jsp._jspService(_ENGJGLT0_jsp.java(Compiled Code))
at org.apache.jasper.runtime.HttpJspBase.service(HttpJspBase.java:119)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.iplanet.server.http.servlet.NSServletRunner.invokeServletService(NSServletRunner.java:897)
at com.iplanet.server.http.servlet.NSServletRunner.Service(NSServletRunner.java:464)hi,
lemme try to tell u what i thinkk..i dont think its' a solution
Usually this error code means that there was some problem while the driver tried establishsing a socket connection to the remote server. You could very well avoid this by tracking out what is preventing the socket connection.. it may be network congestion or some other onfiguration problems with the network, or with the DB2 server...
But if the same application could work perfectly with jdbc-odbc driver in same environment,then it needs some attention.either the ibm driver isn't throwing the error as expected by the iplanet or iplanet isn't acting as needed when such an error is thrown.
contact them and they may provide and explanation..
wishes,
Jer -
The remote server did not respond to a connection attempt
I have two Exchange 2003 servers: Old and New. Emails from the new server can go out however, users on the new server cannot receive emails from the old or the internet.
I get the following error:'....remote server did not respond to a connection attempt....'
All emails are stuck in newserver.domain.com.
KimaniBobHi KimaniBob,
Since Exchange 2003 is a very old Exchange version, we have not supported for Exchange 2003. It is recommended to upgrade your Exchange server to Exchange 2010. Your understanding will be appreciated.
Best regards,
Amy Wang
TechNet Community Support -
Essbase admin server is not responding in 11.1.2.2 and related services ??
Hi All,
I've installed & configured Hyperion 11.1.2.2. When i entered admin & password in EAS console, the message is displaying as Essbase Administration server is not responding. Can you pls. let me know, what is the service for Essbase Admin services. Also when i'm trying the link http://servername:9000/interop, page not found is displaying. Is it must that Hyperion Configuration Manager service should be up & running ? Where i can find the service for shared services ? where i can find all the related services of different hyperion products. Thanks in advance for the help
Thanks,
PVRIf you have deployed all the web applications to a single managed server then there will be one service to start the web apps - "Hyperion EPM Server - Web Application"
You can tell in the configurator if you have deployed the web apps to a single managed server and - http://2.bp.blogspot.com/-vhvxHXJ6C18/T4Wa0iSeW8I/AAAAAAAAEfg/v7ktkUIqmug/s1600/image023.png
The default port is 9000, if you are still having problems then it is worth checking the logs.
Cheers
John
http://john-goodwin.blogspot.com/ -
Firewall: Error sending to the socket, server is not responding.
Hi all,
I'm trying to connect AIX machine to NT DB2 Database through JDBC with a firewall. I'm using the standard port 6789 in JDBC Applet Server in NT DB2. But I've gotten the following message:
COM.ibm.db2.jdbc.DB2Exception: [IBM][JDBC Driver] CLI0614E Error sending to the socket, server is not responding. SQLSTATE=08S01
The connection chain I'm using for AIX side is:
jdbc:db2://192.168.3.4:6789/DATABASE
I've configured the firewal to allow the port 6789 to be used, and also the other port 51544 (it's for remote administration, I think). I've also checked that wires and other stuff is working fine, but stil I cannot connect to the Database.
I don't know if there's something missing on the firewall configuration. Before, everything was working without the firewall.
Any help will be apreciated, THanks.
Rodrigo, SPAINIt looks like no port problem is happening, because we freed all the ports just to see if client tried to use some of them without our knowing. But it was still the same.
We were thinking about routing issues, but we were able to ping from client to server, and ports 6789 and 51544 were open as well. Maybe JDBC Client Driver is looking for an different IP address than 192.168.3.4. We know the firewall doesn't receive any query from JDBC Client, and that's very strange because if you see the routing tables in AIX machine, the default route is the firewall. Of course, there's not any other static defined route for the server (192.168.3.4), so it's supposed that default route is going to be used. But it's not.
We also restarted client machine from scratch but nothing. Maybe this problem happens because there's something wrong in AIX networking settings.
Rodrigo -
We are using SQL Server 2012.
Every now and then, when we execute the below stored procedure INSERT_INTO_MYTBL, we got the below error, and it returned @ID = 0.
"Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding.
This failure occured while attempting to connect to the Principle server."
What causes this error, and how can we fix it ?
Thank you.
create procedure INSERT_INTO_MYTBL
@ID int output,
@Order varchar(50) = NULL,
@ACCOUNT varchar(20) = NULL
AS
DECLARE @Success int, @TryNr int, @ErrMsg varchar(500), @ErrNumber int, @expected_id int;
SET @Success = 0;
SET @TryNr = 1;
SET @ErrMsg = ''
WHILE @Success = 0 AND @TryNr <= 3 and @ErrMsg = ''
BEGIN;
BEGIN TRY;
BEGIN TRANSACTION;
retry:
BEGIN TRY;
SELECT @expected_id = ident_current('myTbl') + 1
SELECT @order = @account + '-' + CAST(@expected_id AS varchar(50))
insert into myTbl
([Order],ACCOUNT)
values
(@Order,@ACCOUNT)
END TRY
BEGIN CATCH;
SELECT @ErrNumber = ERROR_NUMBER()
IF @ErrNumber = 2627
BEGIN;
GOTO retry
END;
ELSE
BEGIN;
SET @ErrMsg = '1.' + ERROR_MESSAGE() + ' ' + @order
RAISERROR (@ErrMsg, 16, 1);
END;
END CATCH
select @ID = SCOPE_IDENTITY()
IF @id <> @expected_id
BEGIN
UPDATE myTbl
SET [Order] = @ACCOUNT + '-' + CAST(@ID AS varchar(50))
WHERE ID = @ID
END
SET @Success = 1
COMMIT TRANSACTION;
END TRY
BEGIN CATCH;
ROLLBACK TRANSACTION;
SELECT @ErrNumber = ERROR_NUMBER()
IF @ErrNumber = 1205
BEGIN;
SET @TryNr = @TryNr + 1;
IF @TryNr > 3
RAISERROR ('Giving up after 3 consecutive deadlocks for %s', 16, 1,@ACCOUNT);
END;
ELSE
BEGIN;
SET @ErrMsg = '2.' + ERROR_MESSAGE() + ' ' + @order
RAISERROR (@ErrMsg, 16, 1);
END;
END CATCH;
END;When the problem occurs, the stored procedure returns @ID = 0, which I think means the query
When the problem occurs, the procedure does not return anything. SQL Server was told to stop executing. Furthermore, unless you issue the command SET XACT_ABORT ON, SQL Server will not roll back any open transaction. Which is one more reason you should not
permit command timeouts.
As for why this procedure sometimes take a long time, I would primarily suspect locking. When this occurs (but before the timeout elapses!), you could use my beta_lockinfo to see if there is any blocking going on. You find it here:
http://www.sommarskog.se/sqlutil/beta_lockinfo.html
Erland Sommarskog, SQL Server MVP, [email protected] -
Authenticated Bind succeeds but "This server is not responding"
Hey everyone,
I have a "from scratch" magic triangle setup. AD has 2 DC's in a domain named domain.priv, 1 Lion (10.7.4) OD server successfully bound to AD and authentication is working flawlessly and fast! There are a handful of clients running SL which have mobile homes. There are also a handful of Lion clients with mobile homes. DNS is running on AD.
Here's the rub. I can bind the SL clients to AD and OD just fine. I do an authenticated bind to OD so that it creates the computer record. On the Lion clients I bind them to AD without a problem and OD without and error message however once I bind Directory Utility has a red light stating "This server is not responding". Search paths are correct, pinging works the server works. Because authentication and mobile homes are working I think it's fairly safe to assume DNS is setup properly.
For clarification, I have a script that does the binding but I promise I've tried every available option in dsconfigldap without success. I've obviously tried using the GUI as well with no luck. I've tried turning on SSL and no SSL. I've tried enabling other security options without success as well. A work around I have found for the Lion clients was first do an authenticated bind to create the computer record and add it to appropriate computer groups then unbind the client and rebind UNauthenticated. Binding without authentication works perfectly and the client never loses contact with the OD server.
The reason I am posting this problem is because I am finally getting around to adding a secondary OD server for replication. I do not have the option to do an unauthenticated bind with OS Server and I have not found a way to successfully setup a replica without binding first, obviously.
I will post log files as needed but I have not found anything that is out of the ordinary except for:
9/20/12 7:34:16.560 PM servermgrd: -[PasswordServerPrefsObject getSearchBase]: Unable to locate search base: -1 Can't contact LDAP server
9/20/12 7:34:16.562 PM servermgrd: -[PasswordServerPrefsObject loadXMLData]: Unable to locate passwordserver config record's plist attribute: -1 Can't contact LDAP server
9/20/12 7:34:16.564 PM servermgrd: -[PasswordServerPrefsObject getSearchBase]: Unable to locate search base: -1 Can't contact LDAP server
9/20/12 7:34:16.567 PM servermgrd: -[PasswordServerPrefsObject saveXMLData]: ldap_modify_ext_s of the passwordserver config record's plist attribute: -1 Can't contact LDAP server
It goes on like that...
Also, IPv6 is not setup on the AD DNS servers. Not sure that matters but I figured I should put it out there.
Any help or ideas of where to look would be greatly appreciated! Thanks!
Nick.I ended up opening a ticket with Apple and the cause has been identified and even a "fix"!
Turns out that I skipped a vital step prior to binding to AD or setting up the OD Master; preparing the server to connect to another directory.
It's necessary to go to Server Admin, select Open Directory, Settings, then Change. Select "Connect to another directory" and then continue. After that the normal steps should be taken; Connect to AD with Directory Utility and then Create Open Directory Master with Server Admin.
Since I have a test enviroment that consists of 1 week old backups of the AD Domain Controllers and OD Master I decided to destroy the current OD and start over and testing this out. Guess what? Everything works as it should. Bount a couple of Lion clients, tested management, and even created a replica with the GUI!
Here's the rub...
In order to keep my current environment in tact (computers and computer groups) I exported all of the computers and computer groups from WGM prior to destroying the Open Directory Master. Once I completed setting everything up and created a new Directory Master I reimported the archive. With this method all currently I was back to square one. SL clients were bound, I could unbind and re-authenticaed bind with no problems. Lion clients however, had the same issue, could not bind with authentication. Fail.
I also tried exporting the computers and computer groups from WGM prior to destroying the Master. Set everything back up, imported the computers and computer groups. Nice part is that new binds both SL and Lion work wonderfully. However, any machines that were already bound don't work. I assume this is because even though the Kerberos realm has the same name, there has to be some differences in hash or whatever else Kerberos is using for encryption. There are log entries telling me about all the computers trying to connect that the server can't find in it's database.
Where to go from here?
Not sure. How do I find out what is broken in the Archive? I know that 10.7 took out the option of -merge in slapconfig which may or may not have worked here. Knowing what the "Connect to another directory" option in Server Admin is doing would help out greatly. Not knowing why that simple step does changes everything is deflating to say the least.
I should be talking to an Apple Engineer tomorrow. I will post back.
Nick. -
VPN Problems - The L2TP-VPN server did not respond
Okay, so I read quite a few threads about this and can't really figure it out. Would be great if I can get some handholding.
I'm a complete newbie, trying to set up Server for home use. The VPN service seems to be running fine, but I just can't connect from the clients, it just keeps saying "The L2TP-VPN server did not respond". Here is a glimpse at my settings:
- I have opened up all the relevant ports for UDP (500,1701,4500) and TCP (1723). But this is only required for the Server, right?
- I don't have a domain name yet so just using my external IP. This is what I put in under VPN Host name in the Server and Client settings.
- I login with username and password credentials for one of my network users as created in the Server. Format is [email protected] and the password is the same as the login password.
** I seem to get a 'authentication failed' error if I just use my local IP address... Not sure whats happening their, but before that I need to be able to connect to Server with the external IP!
Am I missing something? Why won't my client connect and that too when I'm at home?To run a public VPN server behind an NAT gateway, you need to do the following:
1. Give the gateway either a static external address or a dynamic DNS name. The latter must be a DNS record on a public DNS registrar, not on the server itself. Also in the latter case, you must run a background process to keep the DNS record up to date when your IP address changes.
2. Give the VPN server a static address on the local network, and a hostname that is not in the top-level domain "local" (which is reserved for Bonjour.)
3. Forward external UDP ports 500, 1701, and 4500 (for L2TP) and TCP port 1723 (for PPTP) to the corresponding ports on the VPN server.
If your router is an Apple device, select the Network tab in AirPort Utility and click Network Options. In the sheet that opens, check the box marked
Allow incoming IPSec authentication
if it's not already checked, and save the change.
With a third-party router, there may be a similar setting.
4. Configure any firewall in use to pass this traffic.
5. Each client must have an address on a netblock that doesn't overlap the one assigned by the VPN endpoint. For example, if the endpoint assigns addresses in the 10.0.0.0/24 range, and the client has an address on a local network in the 10.0.1.0/24 range, that's OK, but if the local network is 10.0.1.0/16, there will be a conflict. To lessen the chance of such conflicts, it's best to assign addresses in a random sub-block of 10.0.0.0./0 with a 24-bit netmask.
6. "Back to My Mac" on the server is incompatible with the VPN service.
If the server is directly connected to the Internet, see this blog post. -
IVPN starts, but "the pptp-vpn server did not respond. Try reconnecting."
Hi. I am new to VPN, and I just got the software iVPN from Macserve, and the server starts successfully, using either PPTP or L2TP:
But the connections from my network do not connect. Every time I click on "connect" for either network connection, I get the error "the pptp-vpn server did not respond. Try reconnecting."
I set up both connections in my Network Preferences according to the support page (http://macserve.org.uk/support/ivpn/):
My Airport Express configurations have never given me any problems with my home network:
And I think that I forwarded the ports properly (even though my firewall is not activated):
What am I doing wrong?The Apple routers can be a problem on vpn passthrough.
Ports that are required for vpn are more complicated ..
See earlier post.. eg How do I set up L2TP VPN?
Ports for PPTP which you have opened manually.. are not valid for L2TP.. so you need several more ports opened.
The problematic ones are GRE and ESP which are protocols not ports.
I think you can pretty well assume the apple router running anything that has BTMM in it won't work.. since it will need the port 500 for itself.
On the old express try going back to 7.6.1 firmware.. I have to say I don't use the express.. lots of extreme and TC.. so their firmware issues are slightly different so firmware versions for the express are somewhat different.
Try not to use both port forwards (mapping if you must).. and DMZ.. they can fight each other.. if DMZ doesn't work it is better to turn it right off and forward all the required ports.
Let me recommend a test.
Plug your cable modem directly into the computer running the VPN.. so you have no NAT router in front of it.
Pay attention to the local firewall that apple runs and what ports you will need to open on it to get vpn to work.. this is your best chance to get remote vpn running. If you fail with the public IP on the computer it will certainly fail through NAT.. and generally local firewall will be an issue.
You should of course test that a client in the local lan can connect by the vpn.. it is always worth testing from the easiest configuration to the most complex.
So local lan just as you have now..
Then direct cable connection to the computer.
Then NAT router.. but you can pretty well assume apple routers are going to be problematic because apple want to dally at BTMM using same ports as IPSEC uses for L2TP.
My email is live.. roll your mouse over it and talk to me direct.. -
Problems with Tomcat Server : Does not respond (Sometimes) - Plz Need Help
I have a web application running on Tomcat 4.1.31. (SUN/Solaris)
Clients access through iPlanet Web Proxy (SUN/Solaris).
Theres a class that build a generic form (it return html codes) then it's affected in the JSP page :
MyClass class = new MyClass();
<%= class.getHtmlCode() %>
the size of the form is variable (100Ko to 1,5Mo)
When i m using the proxy, sometimes the server does not respond when he do the affectation <%= class.getHtmlCode() %>.
If i call the page without proxy it work.
The problem seem not depending of the size of the form. Without proxy it always work. And with proxy sometimes the server does not work.
Please need helpOriginally Posted by scum
Hey All,
Need some help with ZDM7 PXE preboot services.
Currently running a netware 6.5 server in VLAN1
PXE client sitting in VLAN2.
DHCP Server is running on VLAN3
IPHelper is running
DTS.ini, PDHCP.ini and TFTP.ini are unmodified.
I have had networks put an IPHelper in place and my client successfully picks up an IP address. The screen displays the "BOOT SERVER IP" correctly and the clients IP details are correct.
I watch the top of the screen where the Timeout counts down and eventually gives this error.
"Error: The server did not respond as requested in time
ZENworks shutting down...
Press any key to continue..."
This happens on every machine i have tested. If i hold down the Ctrl+Alt keys, then the imaging menu appears, i can select maintenance and the client will pull down the initrd, etc.. fine.
if i disable the IPHelper, move the client to the same VLAN as the server, then the whole process works perfectly.
not sure where to go from here.
help please ;)
leon
Hi Leon,
If you are getting the ZENworks menu when holding down the Ctrl-Alt keys, PXE/PDHCP seems to be doing the right thing. Routing issues also don't seem the case as you can pull down the first PXE boot files....
The server running PXE, I assume it also runs the TFTP and Imaging services?
These services are also running a recent version of Zen 7 (IR3/IR4)? A little more info on these components and what server they are on would be good :)
Cheers,
Willem -
The app updates button will not respond to my touch
the updates button shows updates are avaialble but it will not respond to my touch, you can update it by scanning all your purcahsed apps and selecting update but this is long way round..any ideas?
The update server is down for the last few days.
-
OD replica, DNS secondary zone, server will not resolve itself
We are testing an OD replica to run in a separate location from our OD master. Master OD and DNS is all set and working as expected. Separate location network user connections and DNS all work as expected when calling the OD master and DNS primary zone. The OD replication works fine. I want to use the same machine as a DNS secondary zone getting its records from the DNS on the OD master. DNS secondary zone seems to pull the records from the primary without trouble.
In testing the secondary DNS without forwarders or backup DNS systems, known internal addresses are resolved by the clients correctly. The issue that I am trying to resolve is that server will not resolve itself. I have the System Preferences / Network / DNS pointed to 127.0.0.1. The DNS is resolving for the clients. Running changeip -checkhostname gives
"The DNS hostname is not available, please repair DNS and re-run this tool."
If I ask a client to browse to the server's web site it resolves fine and I get the default page as expected.
With all of the above in mind, binding a local client to the OD replica and pointing the clients' DNS at the DNS secondary zone results in failure of the bind and the client saying that the server is not responding. If the DNS on the client is pointed to the DNS primary zone, the bind works fine and everything behaves as expected. Pointing the Server to the DNS primary zone resolves the problem as well and it is able to resolve itself.
The problem is that if our connection to our primary site goes down, I want everything to function independently at the second location. If the primary DNS zone is gone the OD replica server cannot resolve itself and authenticaion then does not happen making the OD replica pointless.
Any ideas?
Thanks.Found it. I did not copy the reverse mappings from the primary DNS zone.
On the primary zone
- In Server.app/DNS/ select show all records in the gear
- double click reverse header for each subnet and indicate to allow zone transfer for the reverse records
On the secondary zone
- Add additional secondary zones for the exact title of each reverse record zone
- example main records are FQDN.com
- reverse records are 2.81.10.in-addr.arpa for the items in the 10.81.2.0 subnet
OD replica now resolves itself.
Maybe you are looking for
-
hi, whilw iam filling setup table iam getting the error <b>No extraction structure active or no BW</b> in rsa5 and rsa6 i did the procedure inlbwe that ds is active i deleted the set uptable after i fill the set up table iam getting this error iam
-
How count the total number of instances ?
I have 2 scenarios :- 1. How to get the total number of instances of the node in a BO? eg : businessobject BO1 { element BO_ID; node NODE1 [0..n] element Node_ID; element Status ;
-
What is setting required In Middle ware?
What is setting required In Middle ware?
-
I have two panels on the screen - one a graph drawn without layout manager, the other placed South of the graph containing a set of checkboxes. The graph panel implements printable and, when printing, the idea is to pass the check box panel to the gr
-
Is Photoshop compatible with Windows 8?
It seems windows 8 and ps6 are not compatible