AIR-AP1141N connected to Cisco linksys E1200

    Does anyone know if it possible to get dhcp service to an AP1141N when it is connected to  > Cisco Linksys E1200 > cable modem?
The AP gets an IP for the BVI1 interface, the client associates but I get no IP assigment for the client.
What am I missing?
You may be wondering why I am doing this considering that the linksys is already wireless router. It is just a test to see if it possible. The linksys provides IP's and internet access just fine when the AP is not in the mix.

At one time I had a netgear wireless router and I was able to make this work. I replaced the netgear with the cisco linksys E1200 and now I cannot get it to work.
Attached is the AP config that I used when the netgear was in use.
The only think that is different now is that the IP addr that is assigned to the BVI1 interface.
The default gate on the netgear was the same as you see here.
=
Building configuration...
Current configuration : 2109 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname mbtest
logging rate-limit consol
no aaa new-model
dot11 syslog
dot11 ssid mbvisitor
   vlan 101
   authentication open
   authentication key-management wpa version 2
   guest-mode
   wpa-psk ascii 7 10681B415124185A54
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
encryption vlan 101 mode ciphers aes-ccm
ssid mbvisitor
antenna gain 0
speed  basic-5.5 basic-11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
no dot11 extension aironet
interface Dot11Radio0.101
encapsulation dot1Q 101
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
i
interface GigabitEthernet0.101
encapsulation dot1Q 101
no ip route-cache
bridge-group 101
no bridge-group 101 source-learning
bridge-group 101 spanning-disabled
interface BVI1
ip address 192.168.1.4 255.255.255.0
no ip route-cache
ip default-gateway 192.168.1.1
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
login local

Similar Messages

  • Vizio smart Tv won't stay connected to my linksys e1200 while playing Netflix

    I have a Vizio Smart TV and just over the last couple of days I cannot seem to get it to stay connect to my Linksys e1200 router.  I will start a movie on Netflix and it will play for about 10 minutes and then disconnect.  I talked to somebody in Cisco Linksys Customer support and they said that the problem had something to do with IP Addresses.  I have no idea what he was talking about.  All I know is last week I could watch an entire movie without losing connection and this week it only stays connect for 10 minutes and then I have to turn the TV off to re-connect. 
    Ideas?
    Thanks

    Umman, is your Smart TV wirelessly connected to the router? There may be an interfering wireless signal in the area that interrupts the connection. Try changing the router's wireless channels to avoid interference. 
    Here's an article that may help.
    http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=3759

  • Wii connection problems CISCO LINKSYS E1000

    I am trying to connect to my wii with my wireless routed it is a cisco linksys e1000 and and I tried connect and it said error so I went to manual set up.and couldn't figure out the codes to enter I couldn't find the disco codss on the nintendo website. Please help me I.really wanna.connect my wii to the Internet

    Well the situation is not well elaborated. What is the exact ERROR you are getting while trying to connect your Wii? What code are you talking about? It might be asking to put 8 digits pin number which is on the Linksys E1000 itself.

  • Connecting a Cisco linksys E 2500 as an access point with my Apple time capsule

    Is it possible to extend my network using a Cisco linksys E 2500 with my existing time capsule.  My main source for the Internet goes to my time capsule and I have two airport express and want to add the Cisco router.  I want to put this router by my entertainment center where I have yv etc. that need to be plugged in.  I extended my network by using the airport express with no issues but need the extra Ports to plug in all the equipment that's why I want to use the Cisco Linksys.

    The Cisco cannot extend the wireless of the Apple router.. sorry it is impossible.
    You can use the Cisco as a switch but then again you could buy a switch for a few dollars and use that with the express.
    Do you feel brave.. well do ya'
    Flash your E2500 to dd-wrt and face the consequences.
    http://www.dd-wrt.com/wiki/index.php/Linksys_E2500
    It can then be used as universal wireless bridge or repeater.. I do not recommend this.. IMHO universal repeater is lousy and you are asking for years of bad wireless dropouts. But it is possible.. vaguely .. to do.
    Better use EOP (homeplug) adapters.. and wan bypass or APmode the E2500.. that is very viable.
    Best.. use ethernet to the area and use the E2500 as a switch and wireless AP.

  • Cisco Linksys E1200 Router says ethernet cord is not connected

    Hello,
    I first had issues when there was a large thunderstorm that passed through the area. Lightning struck in my complex, and caused a large powersurge to go through my building. My router is plugged into a surge protector so I figured that it would be okay. The internet was out for a few days, and I only realized it came back when I plugged the ethernet cable directly into my laptop. 
    I have tried unplugging the router and waiting for a few minutes, then plugging it back into the power sources, then plugging the ethernet cable back in. To no avail, the internet is still unavailable to me wirelessly. I have tried different ethernet cords with no success. I reset the device to factory settings and have tried to set it back up with the CD and still no success; it does not recognize that the ethernet cord is plugged in. 
    I've had this router for about 2 years now and never had any problems till now. What can I do to fix it, if anything? Or do I need to just get a new one? Thank you! 

    Power surge blew the Internet Port on the router. In this senario the power surge came in via the ethernet internet connection as well. You will have to replace the router.
    Please remember to Kudo those that help you.
    Linksys
    Communities Technical Support

  • Vizio E3D320VX TV will not connect to Cisco Linksys E4200V2 5Ghz N-band

    Hi just got a Vizio E3D320VX TV and it will connect to my E4200V2 2.4Ghz N-band, but not the 5Ghz N-band. Both 2.4Ghz and 5Ghz are configured virtually identical: 1) both are Wireless-N Only, 2) both auto channel width, 3) both WPA2 Personal security, 4) both SSID broadcast disable.
    The only differences are: 1) obviously the SSIDs and 2) I manually set the 2.4Ghz channel to the least used in my area. I kept the 5Ghz channel auto.
    To connect to 2.4Ghz, in the Vizio TV network settings, I left their settings to Auto (DHCP), and put in the SSID name. The TV searches for it, sees that it's WPA2PSK and asks for the password. Put it in and boom it works.
    When I try on 5Ghz (again on "Auto"/DHCP for the TV), I put in the SSID, and the TV "thinks" about it for awhile, then says something like "Cannot connect, please try another Wireless Access Point". It never gets to the point where it asks for the WPA2 password.
    The TV is downstairs and the E4200V2 is upstairs, but I used my iPad2 in the same room and it connects to the 5Ghz with no problem. But just in case the TV has a 5Ghz reception problem, I set the channel width to wide/40Mhz and bumped tried a couple of the higher channels (149 and 161), and it still won't connect.
    I also went into Administration and turned on logging to try to see what is happening when the TV tries to connect, but for some reason nothing is logging, not even my other devices' traffic -- very strange (yes I hit Save Settings after enabling logging).
    I saw another post about a Vizio Blu-ray player that was having streaming problems, and the suggestion there was to adjust the MTU, but I'm guessing that's irrelevant to my issue.
    Anything else I can try to try to get it to connect? Thx, John.

    Hello,
    Try the one suggested by jlbjlb, name the 2 bands differently as well as the wireless channel so we can do some isolation.
    For the wireless channel don't use auto, you can play around with 40MHz or 20Mhz then try connecting again.
    So you'll be sure also of the adapter's wireless capability is its dual or not built in to it, perhaps you could ask the manufacturer.

  • Linksys E1200 patch 2.0.05 build 2 Mar 28, 2013 - still keeps loosing Internet connection

    Hi Guys,
    Anyone with the above issue - suddenly now my internet keeps loosing connectivity.
    Is it the ISP fibre issue or the cisco linksys e1200.
    Any feedback appreciated.
    many thanks in advance
    francis

    To properly isolate on which device is not working properly is to disconnect the router from the setup and connect your main computer directly to the modem (via Ethernet cable). You can observe the internet connection through the modem for at least 24 hours. If you find that the modem is working fine (stable) then the problem is with the router. So what you can do is reset the router (pressing and holding the button down) for 15 seconds and power it down for also 15 seconds. You re-configure the internet connection on the router after that. Set the wireless settings, too, like change the SSID, set the channel to something else and make sure that wireless security is enabled. You use WPA2 for wireless security on the router.
    You can check the links below as well:
    Setting up your Linksys wireless-N router without using the setup CD
    http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=22734
    Resolving dropping wireless connections
    http://www6.nohold.net/Cisco2/ukp.aspx?pid=80&vw=1&articleid=4029
    Top causes of dropping wireless connection on a Linksys router
    http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=efc03a44a5bb47bd804cf4d0eb3015c8_Top_Causes_of_Int...

  • Linksys E1200 Connecting with Cisco WAP4410n Wirelssly

    I have a Linksys E1200 Wifi Router which is connected on LAN Port 1 with Switch. I have enable DHCP through my Server with Internet Connection Sharing.
    Now I want to expand my wireless range with 5 WAP4410n in a building.
    Can I connect Cisco WAP4410n with E1200 Router? If yes then what will be the WAP4410n AP Mode?
    How can I Connect all 5 APs' with same SSID to expand my wireless range?
    Moreover, I can access easily to Linksys E1200 on my machines easily within the range but I want to expand the range without the cable.

    You might post a direct link to this forum or particular thread if there is informaton on it available. 
    Jcol wrote:
    Hi! I actually have a similar concern with my Ciscobusiness class device before, but I went to a different forum. Try community.cisco.com and I think they have the answers to your question. Hope this helps!

  • My Cox Cable/Telephone splits to a telephone modem and a broadband modem.  The BB connects via ethernet to a Cisco Linksys E2500 wi-fi (whatever).  Can I plug my usb printer into the E2500, configure, and then print from my iPad?

    I have just purchased an iPad 2.  I have wi-fi for roku and have connected the iPad to it.  I want to print to my usb printer.  My connection is:  Cox Cable spit to telephone and broadband.  The broad band feed goes to a Cox modem and feeds the wi-fi.  The Cisco Linksys E2500, wi-fi's the Roku and iPad.  Can I USB from the wi-fi to the printer, configure (however), and then print from my iPad?
    If not, how?
    All comments will be appreciated.
    Alan G. Watkins

    the ipad cannot airprint to a non airprint printer.... i think that the only solution is to install helper software on a computer that has an attached printer and share it through the computer only...computer would have to be always left on
    try this....http://www.collobos.com

  • I JUST BOUGHT AND INSTALLED A LINKSYS E1200 WIRELESS N ROUTER AT HOME. MY IPHONE CONNECTS WITH A STRONG SIGNAL BUT WHEN I TRY TO USE THE INTERNET IT JUST LOADS FOREVER. HOW CAN I FIX THIS?????!!!!

    I JUST BOUGHT AND INSTALLED A LINKSYS E1200 WIRELESS N ROUTER AT HOME. MY IPHONE CONNECTS WITH A STRONG SIGNAL BUT WHEN I TRY TO USE THE INTERNET IT JUST LOADS FOREVER. HOW CAN I FIX THIS?????!!!!

    RESET YOUR ROUTER
    No. Reset your router.

  • Linksys WAP54G connecting to CISCO ACS via LEAP

    I understand that Linksys WAP54G support WPA and 802.1x authentication. Will a cisco compatible client card get connected to the WAP54G via LEAP authentication to a Cisco ACS server ?
    Connection scenario:-
    Cisco compatible client card <-WPA/LEAP-> WAP54G <-WPA/LEAP-> Cisco ACS3.1
    Pls advise if such setting is feasible.
    Tks

    This is really a question for Linksys support. The Cisco wireless BU has no involvement with the Linksy's product line. They operate as a totally separate wholly own subsidiary of Cisco.
    As for LEAP, no, to my knowledge the Linksys AP does not support LEAP, which is not tested or part of the WPA certification program. To my knowledge the ONLY APs that support LEAP are Cisco Aironet APs.
    If the Linksys supports WPA-Enterprise, then any client that supports WPA-Enterprise should work using EAP-TLS. The Cisco ACS server supports EAP-TLS.
    One word of caution. Early CCX cards do not necessarily support WPA. The CCX specification and certification were out before WPA was released. You will need to check with the actual vendor of the card to verify WPA compatibility.;
    Also there are two types of WPA. WPA-Personal, which supports only the WPA encryption, and the keys are handles by a Pre-shared Key input system (no radius server) and WPA-Enterprise, which is certified using WPA encryption an 802.1x EAP-TLS radius server (in fact using Microsoft and Funk Software servers). make sure that the Linksys supports WPA-enterprise, or it may not support 802.1x.
    Bruce Alexander, Cisco

  • Connection issue of AIR-AP1141N-A-K9.

    Dear all,
    I have some connection trouble with AIR-AP1141N-A-K9.
    I put a IP camera in my home and connect to AIR-AP1141N-A-K9 via wireless.
    After a while about 1 week, the wireless will be dissociated.
    Does anyone have the same issue of wireless?
    Below are some information & log message of AP.
    Please give me some suggestion to resolve this issue, thanks.
    AP information
    Product/Model Number: AIR-AP1141N-A-K9 
    Top Assembly Serial Number: FTX1533KDNF 
    System Software Filename: c1140-k9w7-tar.124-21a.JA1 
    System Software Version: 12.4(21a)JA1 
    Bootloader Version: 12.4(23c)JA1 
    System Uptime: 3 days, 2 hours, 39 minutes 
    Log message
    sh syslo               loo   gg
    SEKISUI_184#sh logging
    Syslog logging: enabled (1 messages dropped, 2 messages rate-limited,
                    0 flushes, 0 overruns, xml disabled, filtering disabled)
        Console logging: level debugging, 84 messages logged, xml disabled,
                         filtering disabled
        Monitor logging: level debugging, 0 messages logged, xml disabled,
                         filtering disabled
        Buffer logging: level debugging, 84 messages logged, xml disabled,
                        filtering disabled
        Logging Exception size (4096 bytes)
        Count and timestamp logging messages: disabled
        Trap logging: level informational, 85 message lines logged
    --More--                          
    Log Buffer (4096 bytes):
    6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f07d.6806.287a Reason: Sending station has left the BSS
    May 18 16:03:56: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   f07d.6806.287a Associated KEY_MGMT[NONE]
    May 18 16:04:39: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f07d.6806.287a Reason: Sending station has left the BSS
    May 18 16:04:44: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   f07d.6806.287a Associated KEY_MGMT[NONE]
    May 18 16:06:08: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f07d.6806.287a Reason: Sending station has left the BSS
    May 18 16:06:13: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   f07d.6806.287a Associated KEY_MGMT[NONE]
    May 18 16:40:27: %DOT11-4-MAXRETRIES: Packet to client f07d.6806.287a reached max retries, removing the client
    May 18 16:40:27: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f07d.6806.287a Reason: Previous authentication no longer valid
    May 18 16:40:27: %DOT11-4-MAXRETRIES: Packet to client f07d.6806.287a reached max retries, removing the client
    May 18 16:40:42: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   f07d.6806.287a Associated KEY_MGMT[NONE]
    May 18 16:43:03: %DOT11-4-MAXRETRIES: Packet to client f07d.6806.287a reached max retries, removing the client
    --More--                           May 18 16:43:03: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f07d.6806.287a Reason: Previous authentication no longer valid
    May 18 16:43:03: %DOT11-4-MAXRETRIES: Packet to client f07d.6806.287a reached max retries, removing the client
    May 18 16:43:18: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   f07d.6806.287a Associated KEY_MGMT[NONE]
    May 18 16:45:35: %DOT11-4-MAXRETRIES: Packet to client f07d.6806.287a reached max retries, removing the client
    May 18 16:45:35: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f07d.6806.287a Reason: Previous authentication no longer valid
    May 18 16:45:35: %DOT11-4-MAXRETRIES: Packet to client f07d.6806.287a reached max retries, removing the client
    May 18 16:45:50: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   f07d.6806.287a Associated KEY_MGMT[NONE]
    May 18 16:48:01: %DOT11-4-MAXRETRIES: Packet to client f07d.6806.287a reached max retries, removing the client
    May 18 16:48:01: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f07d.6806.287a Reason: Previous authentication no longer valid
    May 18 16:48:01: %DOT11-4-MAXRETRIES: Packet to client f07d.6806.287a reached max retries, removing the client
    May 18 16:49:43: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   f07d.6806.287a Associated KEY_MGMT[NONE]
    May 18 17:00:37: %DOT11-4-MAXRETRIES: Packet to client f07d.6806.287a reached max retries, removing the client
    --More--                           May 18 17:00:37: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f07d.6806.287a Reason: Previous authentication no longer valid
    May 18 17:00:37: %DOT11-4-MAXRETRIES: Packet to client f07d.6806.287a reached max retries, removing the client
    May 18 17:03:39: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   f07d.6806.287a Associated KEY_MGMT[NONE]
    May 18 17:10:12: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f07d.6806.286e Reason: Sending station has left the BSS
    May 18 17:10:12: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   f07d.6806.286e Associated KEY_MGMT[NONE]
    May 18 17:10:30: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f07d.6806.286e Reason: Sending station has left the BSS
    May 18 17:10:35: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   f07d.6806.286e Associated KEY_MGMT[NONE]
    May 18 17:10:54: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f07d.6806.286e Reason: Sending station has left the BSS
    May 18 17:11:00: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   f07d.6806.286e Associated KEY_MGMT[NONE]
    May 18 17:15:23: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station f07d.6806.286e Reason: Sending station has left the BSS
    May 18 17:15:29: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   f07d.6806.286e Associated KEY_MGMT[NONE]
    SEKISUI_184#    =

    f07d.6806.286e
    Is this the MAC address of your wireless camera?  A D-Link?
    If this is so, can I ask you to post the output to the command "sh dot11 assoc f07d.6806.286e"?

  • TS3742 Installed Cisco Linksys VUSB.  Now my MacBook Air restarts and I get a kernel panic

    Bought a new Cisco Linksys router a few weeks ago.  Had to install their VUSB to manage the peripherals.  Now I keep getting this panic message and my MB Air restarts whenever I log out. How do I fix this?

    Same issue here.
    If Cisco VUSB is running (in the dock) when the Macbook Air goes to sleep, when it awakens a kernel panic occurs every time.  Now I've had to set Cisco VUSB to not launch upon startup to ensure I don't forget about it when putting my Macbook Air to sleep.  Very annoying.
    Thread on CISCO\Linksys forums: http://community.linksys.com/t5/Wireless-Routers/VUSB-OS-X-10-8-2-and-Auto-Conne ct/td-p/620126
    I'm on 10.8.4... and this is Cisco VUSB 1.2.0 (SXUPTP Driver 1.10.0).

  • Cisco Linksys E1000 Connection to Verizon Router

    OK here is the situation.  I spent two with a verizon tech on the following issue.
    I have new PC, windows 7, that I have connected via wireless Trendnet 150Mbps Mini Wireless N USB Adapater. The spped is less than 5Mbps download and upload.  My verizon plan is 25Mbps.  In the end it was determine that the verizon technology is g format and the adapter is n technology. The computer directly hard wired to the verizon router gets 30Mbps speed.
    Bought a Cisco Linksys E1000 N technology router to connect to the Verizon router.
    Connected to router and could not get any internet even though the signal strength was extremely good.
    Got any suggestion on how to get this to work.
    I am dying with this problem,

    When connecting the E1000 router to your fios one, i would use one of the 4 LAN ports and not the WAN port to make the Ethernet connection between the two. Then go into the router web page of the E1000 (192.168.1.X) and make sure that the DHCP server is disabled.
    Now for your speed problem. Even with wireless G you should still be fine as it can tranfer much faster than 5Mbps. The problem could be that the Trendnet usb adapter has a pretty tiny radio and your connection slows way down as you move away from the the wifi source.

  • HT1365 just installed a new wireless router (cisco linkseys E1200) and our apple laptops connect fine on one floor but lose connectivity when moved to another.  Other non apple laptops & Ipad connect with no problem no matter what floor they are on

    We just installed a new wireless router to our main PC.  It's a Cisco Linkseys E1200.  All other wireless devices were able to connect without a problem, including my Ipad.  We have 2 Macbook Pro laptops.  They both connect just fine when on the same floor of our house as the router, but when we take them upstairs to the 2nd floor of the house, they lose connectivity and it states the wireless password is not the correct password.  All other 2nd floor laptops have no problem at all with connectivity no matter where they are in the house.  Please help- my husband is on the verge of selling Apple if that cannot be remedied. 

    This would not be a security issue symptom. I would consider checking for sources of wireless interference HT1365
    Trying changing the radio channel on your wireless network.

Maybe you are looking for