AIR-AP1252-AG-A-K9 with AIR-ANT5135D-R is not working

Hi,
Please find below the attachments of my Cisco AP1252AG-A-K9 Configuration with AIR-ANT5135D-R antenna. I am very near to the access point but i am getting low signal and after some time i am loosing the signal. How to fix this problem. Can anyone help me in this issue.
Thanks,

Is there any configuration mistake or this antennas not supporting to this access point or what?
You may want to call it a "configuration" mistake. Aside from 802.11a (or 5.0 Ghz) inherit or designed limitation of short range it also has one thing "short" and that is the lack of penetration power.
I have no idea what wisdom management has but I'm sure this is not going to work.
Your options are the following:
1. Move the AP from the ground floor to the 1st Floor;
2. Get another AP for the 1st Floor; or
3. Enable 802.11b or 2.4 Ghz.

Similar Messages

I tried to migrate my files from my old G4 book to my new Macbook Air. It did not work properly and I want to restore the Air to its original settings. How do I do this?

I tried to migrate my files from my old G4 book to my new Macbook Air. It did not work properly and I want to restore the Air to its original settings. How do I do this?

You will need to use an external DVD drive to run the disc installer that came you your machine. You can also do it with another Mac using the Remote Install Max OS X app. Finely, if you have access to another computer, you could burn the install image on a USB thumb drive, boot from that, erase the drive and run the installer.
17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G + 120G OCZ Vertex 3 SSD Boot HD 

Upgraded to os7 and done my updates on the apps as they appear.. Any function to do with the iBook store is not working or visible. The purchase at the end of a sample book doesn't work either.

Upgraded to os7 and done my updates on the apps as they appear.. Any function to do with the iBook store is not working or visible. The purchase at the end of a sample book doesn't work either. Anyone have a solution?

Upgraded to os7 and done my updates on the apps as they appear.. Any function to do with the iBook store is not working or visible. The purchase at the end of a sample book doesn't work either. Anyone have a solution?

Hi! I am having a problem with my dictation. It works fine with Greek but it does not work at all with English. Anyone knows why?

hi! I am having a problem with my dictation. It works fine with Greek but it does not work at all with English. Anyone knows why?

Have you changed the system voice to an English one in system preferences?

TS1292 How do I redeem a card with a code that does not work? The support store takes me in circles?

Help and support sends you in circles and does not help redeem a card with a code that does not work.

Well, they have a website, but here is a link to their information about unlocking iPhones.
http://www.att.com/esupport/article.jsp?sid=KB414532&cv=820#fbid=6d7EKuCF_dr
You may not qualify for an unlock though.

[svn:fx-trunk] 5019: ASDoc updates to indicate that some Halo containers do not work with the Spark equiv (ControlBar does not work with Spark Panel/ AppControlBar does not work with Spark Application), and indicate that Canvas, Box, Tile, Panel have Spa

Revision: 5019
Author: [email protected]
Date: 2009-02-19 13:17:21 -0800 (Thu, 19 Feb 2009)
Log Message:
ASDoc updates to indicate that some Halo containers do not work with the Spark equiv (ControlBar does not work with Spark Panel/AppControlBar does not work with Spark Application), and indicate that Canvas, Box, Tile, Panel have Spark equivs
QE Notes: None
Doc Notes: None
Bugs: -
Modified Paths:
flex/sdk/trunk/frameworks/projects/framework/src/mx/containers/Accordion.as
flex/sdk/trunk/frameworks/projects/framework/src/mx/containers/ApplicationControlBar.as
flex/sdk/trunk/frameworks/projects/framework/src/mx/containers/Box.as
flex/sdk/trunk/frameworks/projects/framework/src/mx/containers/Canvas.as
flex/sdk/trunk/frameworks/projects/framework/src/mx/containers/ControlBar.as
flex/sdk/trunk/frameworks/projects/framework/src/mx/containers/HBox.as
flex/sdk/trunk/frameworks/projects/framework/src/mx/containers/Panel.as
flex/sdk/trunk/frameworks/projects/framework/src/mx/containers/TabNavigator.as
flex/sdk/trunk/frameworks/projects/framework/src/mx/containers/Tile.as
flex/sdk/trunk/frameworks/projects/framework/src/mx/containers/VBox.as
flex/sdk/trunk/frameworks/projects/framework/src/mx/containers/ViewStack.as

Hi DST
This is a great effort and gesture. thank you on behalf of all the newbies.
PJ

You must have connected the Time Capsule with a router that does not work with my direct cable from my ISP

you must have connected the Time Capsule with a router that does not work with my direct cable from my ISP

I tried to answer in your other post.. please stick to one thread ..
What method of internet do you have.. is this fibre install.. if so the TC should just plug in and use dhcp in router mode.. press and hold the reset and it will go back to router mode by default.

HT1222 hello i have a problem with my fingerprint id its not working anymore like before his not recognised my finger anymore why ?

hello i have a problem with my fingerprint id its not working anymore like before his not recognised my finger anymore why ?

I have had to periodically delete and re-enter my fingerprint. The last update (7.1) may have improved that. You can delete by going to Settings > Touch ID & Passcode, enter your passcode and then tap "Turn Passcode Off" and then go back to the same area, put a passcode back on and then a fingerprint.

Command.text with ODBC escape sequence is not working in VC++, Bug in OLEDB ?

Command.text with ODBC escape sequence is not working in VC++. The Code, which written in VB is working perfectly. Is there any different syntax in VC++ or bug in
OLE DB provider ?. I am using OraOLEDB 8.1.7 version.
Thanks
Mani
VB Code
' Enable PLSQLRSet property
Cmd.Properties("PLSQLRSet") = True
' Stored Procedures returning resultsets must be called using the
' ODBC escape sequence for calling stored procedures.
Cmd.CommandText = "{CALL corpuser.GetCorpUserRec(?, ?)}"
Set Rst1 = Cmd.Execute
VC++ Code (while execute it is giving error )
pCommand->CommandText = "{CALL corpuser.GetCorpUserRec(?, ?)}";
pRs1 = pCommand->Execute(NULL,NULL,adCmdStoredProc);

Hi
The odbc escape sequence for calling stored procedures works fine with VC++ also.
You can check the sampe application at following url :
http://otn.oracle.com/sample_code/tech/windows/ole_db/content.html
Hope this helps
Chandar

I have a iPhone4 acquired in Portugal. I will be moving to the EQUATOR (South America). Whenever I have visited the country before, with other cellphones, they did not work (different band) forcing me to buy a local cellphone. Will my iPhone4S work there?

I have a iPhone4S acquired in Portugal. I will be moving to the EQUATOR (South America). Whenever I have visited the country before, with other cellphones, they did not work (different band) forcing me to buy a local cellphone. Will my iPhone4S work there?

If it is unlocked it will work if you get a SIM from the carrier you will be using. Note that Apple does not and cannot unlock phones. Only the carrier it is presently locked to can unlock it.

Anyone had issues with on/off sleep button not working anymore

Anyone had issues with on/off sleep button not working anymore?

If there is Warranty or AppleCare make Genius reservation or set up Service and take or send to Apple for resolution. If no coverage, use virtual Lock Button, tap Settings App > General > Accessibility > Assistive Touch > ON > tap new white screen button > Device > Lock Screen. This can even turn OFF iPhone. To turn ON, connect iPhone to power, charger or USB of computer.

Flash, Adobe Air, Time Machine, Safari not working with Snow Leopard

Really need some help with this.
Did an archive and install of Leopard then installed Snow Leopard. No problems yet.
90% of Video sites would not work. Uninstalled and reinstalled Flash. Uninstalled ShockWave, could not reinstall with 10.6.1.
Attempt to install adobe air, received this message: "couldn't write the application to hard drive - please verify and try again." performed verify disk, disk permissions, repair permissions all ok.
Attempted to install Air again, same message.
Tried to use Time Machine to open Safari from a week ago, received message: I did not have permission.
Using Macbook Pro, 2g memory, 80g hd, with 42g free.
Backed up on ext. HD,
Oh, one more, getting a lot of spinning wheels when using Safari that causes a lockup and hard re-start.
I have an expensive piece of software that uses adobe air and I create videos for my business and I'm not able to do so now.
Can anyone give me any ideas what I can do.
Thanks,
Z

After a couple of days of problems with Snow Leopard and flash, safari etc... I figured out the problem is with my account.
I created a new admin account and everything seems to be working. Well almost.
a couple of things I've noticed are right clicking on dock icons does nothing, no option to quit or keep in dock.
Apple Techs', had me change my account months ago to fix a problem with safari crashing. It didn't really work and more problems resulted.
*So now my big question is: How do I move need items over to the new account.* I don't want to move everything over as I might bring what caused the problem in the first place.
What I need are several apps,(like ilife, iwork, firefox, devonthink, 1password etc.) downloads, desktop, docs, files, and book marks.
*What is the best way for me to do this?* Is there anything I need to do re: Snow Leopard on the new account?
I feel like I have a new and functioning Mac again just around the corner.
Looking for your help, thanks,
Z

Apple TV & Mid 2012 Macbook Air 11.6'' - AirPlay not working

So I just purchased the new MBA to replace my 2010 air...which also suffers from a cracked screen. Since mirroring wont work on the old model anyways, I sold the unit and cut my loses (I was going to replace to LCD but decided it wasn't worth the effort.)
Anyways...
I attempted to use the MBA and the mirroring function out of the box and it worked great. Sure the mouse was a little sluggish, and the audio obviously delayed (on the MBA), but synced perfectly to the TV. I watched YouTube videos, and some other flash and HTML5 embeded content. I was prompted for an update for my Apple TV 3, and today for my MBA. After updating, and restarting both units (which I have done several times since then too), mirroring does not work as it should.
When I select the TV usually it would adjust to a resolution higher than the MBA native resolution--but appropriate for the TV. Instead, the MBA screen goes blue, adjusts to the resolution, and then goes blue again, returning to a non mirroring mode.
Sometimes when I do get mirroring to work--at the MBAs standard resolution--AirPlay will be "working" despite it saying that mirroring is off and greyed out.
The biggest frustration out of all of this is that whenever I go to play a video, assuming AirPlay doesn't stop mirroring at whatever random resolution it picks (I have adjusted between a fixed and aspect appropriate setting), the AUDIO will only play through my televisions speakers, and the video will stop feeding and go back to the Apple TV home screen.
It has done this with YouTube, HBOGO, Hulu, and a number of other video streams online.
Has anyone else had this issue so far?
To reiterate:
Using mid 2012 MBA on OSX Mountain Lion
Apple TV 3 will stream audio and mirror sometimes, but stops mirroring whenever video is played.
AirPlay icon will remain available, but will say mirroring is unavailable / greyed despite it actually "working."

Hey thellamaPod,
Thanks for the question. The following resource provides troubleshooting information for AirPlay Mirroring in OS X. Usually, this may be caused by the firewall and a simple tweak of the settings should resolve your issue:
About AirPlay Mirroring in OS X
http://support.apple.com/kb/HT5404
Firewall security settings
If you use a firewall, make sure the following firewall security options have been set to allow AirPlay Mirroring to work:
1. Choose System Preferences from the Apple menu ().
2. Click Security & Privacy, then click Firewall.
3. Click the lock icon to unlock it if it's locked, then type an administrator name and password.
4. Click Firewall Options.
5. Deselect (uncheck) the “Block all incoming connections” checkbox.
6. Select (check) the “Automatically allow signed software to receive incoming connections” checkbox.
Thanks,
Matt M.

My 2012 Macbook Air Keyboard and Trackpad Not Working

This all started last weekend when I installed the latest updates from Apple. The reboot and startup went fine, and nothing happened for a couple of hours, but while I was reading on the Kindle app (fullscreen), the trackpad stopped working. The keyboard stopped working too. Only the power button worked.
Since I received both a Growler and Notification Alert while this was going on, I assume everything else in the background is working just fine, but the keyboard and trackpad simply are not working. I rebooted the machine and it was working just fine. I dismissed it as a one-off occurance.
However the same issue occured a few hours ago, this time with the Safari screen full-screen. Since I was home, I've added a regular USB keyboard and mice, and that's how I'm typing this out on my Macbook Air at the moment
Like I said, this all started after I installed the OSX 10.8.4 updates onto my machine. I've never had a prior issue with the keyboard and trackbar until yesterday.
Any advice?

No one cared enough to answer.

Ipad air 2 touch id not working when plugged in

A very strange problem tonight.
After work, I grabbed my iPad Air 2 which was plugged in to the Apple Charger next to my chair. Touched the home button to open it - nothing happened. Tried again. Nothing happened. Entered the code and the IPad Air opened.
After dinner, same thing. Touch ID did not work with any of 3 fingers. With the code - it opened. So, I decided to delete and redo the finger scans. Turned off - no change - Touch ID not working.
To get a better grip, I unplugged the Apple charger. Viola! Touch ID worked. Plugged it back in. Touch ID stops working.
Powder off, power on. Touch ID works unplugged but not plugged in. I have done the Reset All Settings. No change.
At a loss. This is not a 3rd party charger - it is the Apple one that came with the iPad Air. Anyone got any ideas?
Tim

Make sure the usb wall adapter is from Apple too.
if your using a generic wall adapter and original Apple lightning cable,
the touch ID won't work.
IF you use both apple wall adapter and lightning cable
the touch id should work.
hopes this helps

AIR-AP1252-AG-A-K9 with AIR-ANT5135D-R is not working

Similar Messages

Maybe you are looking for