AIR-CAP3702I booting up in mesh mode and not joining our 5508 WLC
I have a batch of 30+ AIR-CAP3702I-A-K9 APs that I need to setup but none of them are joining to the 5508 WLC and when I connect a console cable and view the output from the AP it shows that it is trying to initiate in mesh mode. I have read other forums that are showing that I need to put in the APs MAC address to a filter list on the WLC for it to show up and then I will be able to change it from mesh mode to local mode. The only issue I'm having with that solution is not knowing how it will affect my current production environment off of that 5508 WLC. I have 69 active production APs with clients working off them and there are no MAC filters currently in place on the WLC. By adding a MAC filter entry for the new APs would the WLC create an implicit deny for all other clients that don't have their MAC addresses entered?? If so is there another work around? Can the mode be changed via the CLI on the AP itself to make it local instead of mesh?
sh capwap client rcb
AdminState : ADMIN_ENABLED
SwVer : 7.6.1.118
NumFilledSlots : 2
Name : AP88f0.4290.7184
Location : default location
MwarName : xxxxx
MwarApMgrIp : x.x.x.x !<it has the correct name and IP of the WLC>
MwarHwVer : 0.0.0.0
ApMode : Bridge
ApSubMode : Not Configured
OperationState : JOIN
CAPWAP Path MTU : 576
LinkAuditing : disabled
ApRole : MeshAP
ApBackhaul : 802.11a
ApBackhaulChannel : 0
ApBackhaulSlot : 2
ApBackhaul11gEnabled : 0
ApBackhaulTxRate : 24000
Ethernet Bridging State : 0
Public Safety State : disabled
AP Rogue Detection Mode : Enabled
AP Tcp Mss Adjust : Disabled
AP IPv6 TCP MSS Adjust : Disabled
Predownload Status : None
Auto Immune Status : Disabled
RA Guard Status : Disabled
Efficient Upgrade State : Disabled
Efficient Upgrade Role : None
TFTP Server : Disabled
Antenna Band Mode : Unknown
802.11bg(0) Radio
ADMIN State = ENABLE [1]
OPER State = DOWN [1]
CONFIG State = UP [2]
HW State = UP [4]
Radio Mode : Bridge
GPR Period : 0
Beacon Period : 0
DTIM Period : 0
World Mode : 1
VoceraFix : 0
Dfs peakdetect : 1
Fragmentation Threshold : 2346
Current Tx Power Level : 0
Current Channel : 11
Current Bandwidth : 20
802.11a(1) Radio
ADMIN State = ENABLE [1]
OPER State = DOWN [1]
CONFIG State = UP [2]
HW State = UP [4]
Radio Mode : Bridge
GPR Period : 0
Beacon Period : 0
DTIM Period : 0
World Mode : 1
VoceraFix : 0
Dfs peakdetect : 1
Fragmentation Threshold : 2346
Current Tx Power Level : 1
Current Channel : 165
Current Bandwidth : 20
It is showing the following error on our WLC in the log file:
Tue Jul 15 14:01:26 2014
AAA Authentication Failure for UserName:88f042907184 User Type: WLAN USER
And here are some of the errors it's showing on the AP after bootup:
*Jul 15 17:47:30.471: %CAPWAP-5-SENDJOIN: sending Join Request to x.x.x.x
*Jul 15 17:47:31.003: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jul 15 17:47:31.031: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jul 15 17:47:31.039: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Jul 15 17:47:31.047: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jul 15 17:47:32.067: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jul 15 17:47:33.067: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jul 15 17:47:35.471: %CAPWAP-5-SENDJOIN: sending Join Request to x.x.x.x
*Jul 15 17:47:35.471: %DTLS-5-ALERT: Received WARNING : Close notify alert from x.x.x.x
*Jul 15 17:47:35.475: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Jul 15 17:47:35.483: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Jul 15 17:47:36.475: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Jul 15 17:47:36.503: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Jul 15 17:47:37.503: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Jul 15 17:48:15.007: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
*Jul 15 17:48:15.007: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
*Jul 15 17:48:15.007: %MESH-6-LINK_UPDOWN: Mesh station 88f0.4290.7184 link Down
*Jul 15 17:48:17.007: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Jul 15 17:48:22.507: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Jul 15 17:59:10.099: %CAPWAP-3-ERRORLOG: Invalid event 31 & state 4 combination
*Jul 15 17:59:10.099: %CAPWAP-3-ERRORLOG: SM handler: Failed to process timer message. Event 31, state 4
Similar Messages
-
iPod is stuck in recovery mode, and not recognized by iTunes.
Tried all of the recommended resets and combinations mentioned, but the ipod is still not recognized. Genius at apple said it may be a hardware error, "The button is broke" but all of the buttons and cords work and i proved it to him. He then said he doesnt know, ma Now what?If it does not work on other computers then I agree with the Genius
-
Ever since I got the new update 5.1 my iPod's been dying faster, even after I charge it. It used to last for at least 3 hours, now it won't even last one hour and dies for no reason (even when it's in sleep mode, and not in use) What's wrong with it? Is it the update? It's lagging as well..
Some Users have Reported that a Restore as New has helped Resolve issues...
Backup and Set Up as New Device
http://support.apple.com/kb/HT4137 -
TS2529 my iphone is recovery mode and not working what to do?
my iphone is recovery mode and not working what to do?
plz help me to get this problem repair
-
Hello
I can not restore my iPhone 4S itunes error says I have 29 and I put it in DFU mode and not working help please
-
Iphone stuck in voice over mode and not accepting passcode
help, my iphone is stuck in voice over mode and not accepting pass code.
If you have Siri set to work while the phone is locked, you can activate Siri by pressing and holding the Home button and saying. "Turn off VoiceOver."
-
How can I read on my Apple Arabic files of Times New Roman or Arial fonts made in PC? when I get the files the Arabic letters are separate and not joined. Is there a common font in Arabic that can convert the Arabic PC Windows files to my Apple?
The same with email messages ,
And when I get Power Point files made in PC Windows, they are like PDF, not Power Point!
Anybody with a good suggestion?Yewtree wrote:
when I get the files the Arabic letters are separate and not joined
Do not use MS Word for Mac, it does not support Arabic. Instead use Mellel, TextEdit, Nisus Writer or OpenOffice. Try the font Geeza Pro if others do not work.
What are you using to read email?
What are you using to read powerpoint? -
Why does my iPod touch automatically go out of DFU mode, and not stay in it until I turn it on?
I put my iPod touch 4g intoDFU mode, then after 10 minutes or so, it turns on with iBoot. I know that DFU mode bypasses iBoot. It automatically boots out from DFU mode. Please help me, because I want to restore it.
Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore, go into Recovery Mode per the instructions here. -
When I try to sign onto my ipod it is in texting mode and not number mode so it won't let me sign in
I am trying to sign onto my ipod and I have a # passcode, but it is in letter mode.
Then you will have to restore the iPod:
Connect the iOS device to your computer and restore via iTunes. Place the iOS device in Recovery Mode if necessary to allow the restore.
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
If you don't have access to a computer
If you are using Find My iPhone, you can use Remote Wipe to restore your device. If you have been using iCloud to back up, you may be able to restore the most recent backup to reset the passcode.
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store -
POP capabilities are gotten in authorization mode, and not transaction mode
I am using Javamail in an email client that requires UIDL support for POP3 servers. There are some servers that return the UIDL capability only in transaction mode, not in authorization mode (eg. pop.aol.com). I am unable to connect to such servers once I upgraded to javamail 1.4.4, since it is now looking at the capabilities before executing the UIDL command. However, it gets the capabilities in authorization mode, and servers like the one above do not send the UIDL capability in this mode. If the capabilities were refreshed in transaction mode (once login was done), UIDL would be returned. This looks like a bug. Is there a workaround for this?
This definitely looks like a bug in AOL's server, please report it to them.
RFC 2449 says:
A capability description MUST document in which states the capability
is announced, and in which states the commands are valid.
Capabilities available in the AUTHORIZATION state MUST be announced
in both states.
If a capability is announced in both states, but the argument might
differ after authentication, this possibility MUST be stated in the
capability description.
(These requirements allow a client to issue only one CAPA command if
it does not use any TRANSACTION-only capabilities, or any
capabilities whose values may differ after authentication.)
6.8. UIDL capability
CAPA tag:
UIDL
Announced states / possible differences:
both / noThis says to me that the UIDL capability, if supported, must be announced in both states
and must not change between states.
You can set the session property mail.pop3.disablecapa to "true" to disable the use of the CAPA
command, which will cause it to assume UIDL is supported. -
IPad stuck in recovery mode and not connecting to iTunes
My iPad is stuck in recovery mode and doesn't connect to iTunes. Please help...
aalyanrajwani17 wrote:
... Because it was jailbroken.
was beginning to suspect that you had done this...
Unfortuately...because you have a jailbroken device you are on your own...
The discussion of Jailbroken Devices is against the Terms of Use of this Forum.
http://support.apple.com/kb/HT3743 -
Mesh AP 1524SB Not Joining Controller
Hello,
I'm just getting started here and have run into some problems.
I have a WLC 5508 running 7.0.116.0 and 1524SB access points.
I have a 3750 switch sitting between them hosting the DHCP.
The switch is using VLAN 1 and the management interface of the WLC is untagged.
The problem is that my APs will not join the controller. I don't even think they are getting an IP address.
When I console into the AP it seems to me that the boot process is interupted and the AP reboots.
I get this message:
*Mar 1 00:00:34.375: %SYS-5-RELOAD: Reload requested by Adj Process. Reload Reason: Mesh Reboots AP ....
*Mar 1 00:00:34.375: %LWAPP-5-CHANGED: CAPWAP changed state to DOWNWriting out the event log to nvram...
And then it reboots. I have attached the entire boot sequence.
Could someone help me out please?
Thanks,
Justin
PS if needed here is the dhcp config:
ip dhcp pool dhcp
network 10.0.0.0 255.255.255.0
default-router 10.0.0.254
option 60 ascii "Cisco AP c1520"
option 43 ip 10.0.0.1
where 10.0.0.1 is the ip of the management interface.Assuming 10.0.0.1 is the controller's management IP address. For 1524SB Mesh AP, you can't use format of "option 43 ip 10.0.0.1", change it to "option 43 hex f1040a000001" on the 3750 switch and try again.
-
Bridge Mode - Could not join 'network '. A timeout error occurred
Have my airport express in bridge mode with a home hub 3 (that has its wireless network disabled). When i go to join the new wireless network i created on the airport express , it gives me the error in my title.
What causes the timeout and how can it be fixed?As I read the network you should be extend wireless network.. not join. And you need to setup the Express to allow it to be extended.. at least on v5 utility.. on v6 it could work automagically.
-
F2 button not booting PC into recovery mode and Multimedia Controller error in device manager.
Hello everyone,
I updated my lenovo ideacentre b540p from windows 7 home premium to windows 8.1 pro. I have two issues that came up after the upgrade.
1. I can no longer access the Lenovo rescue system 3.0 by pressing the F2 button during startup to boot into recovery mode which was possible when I was using windows 7 and because of this I am unable to install the software and drivers that came with the PC.
2. In device manager the multimedia controller driver is not installed. It shows a yellow sign in the other devices group. I have tried different version from the lenovo support site but none of them work. The PC was shipped without a CD containing the drivers but if I can access the rescue system, I believe I will find the driver I need for the multimedia controller.
Solved!
Go to Solution.Audois wrote:
Hi RR7,
You might have a look at this page: http://forums.lenovo.com/t5/IdeaCentre-Desktops-Home-Servers/Windows-8-Recovery-partition-not-recogn...
It's Windows 8 related, but you'll better understand what may happen when your cloned HD has not the same size as the original one.
interesting post, thanks. sadly i'm not sure this really helps. i didnt find what i expected.
the reagent.xml only has two references to offset, and they both refer to the partition that contains windows 7. i have changed this offset on the cloned disk to match the actual partition offset but it makes no difference.
i don't see any reference to the hidden lenovo partition or its offset in the windows recovery.
i also cant see any reference to it in the BCD on either the source or clonded disk.
all i see if pressing F2 on the source OEM when powering on loads a special lenovo recovery environment, and doing the same thing on the clonded disk just shows the windows 7 boot loader option for choosing to boot windows or do a memory test.
my question still remains, what is the magic thats happening when i press F2? -
Help help - my MacBook Air is in sleep mode and not accept my password
My macbook air is in sleep mode now but i'm not able to open it!!
the password dialogue would not accept any entries. It just beeped away at every key stroke but took nothing.
I have not changed my password!The box just shakes when I type in the password. it doesn't give me the option to use guest login as I have changed the login setting to single user.
Maybe you are looking for
-
I updated to Firefox 14.0.1; my Operating System is Windows Vista on my Compaq Presario C700. I have taken it to the computer repair shop and they said they found a Trojan and removed it. It was still operating VERY slowly, so I took it back in. They
-
Why can't I drag my files in finder to an external hard drive?
I'm trying to drag my files from finder to an external hard drive--I just get the universal "do not" symbol. How do I do this?
-
How to run my vi from a front panel control without using even structure in the vi
Hello, I would like to run my vi from a front pannel control instead of the tool bar RUN botton. I am using LV6.1 without the even structure feature, so I can't do as proposed by a previous posting by setting the vi to run at open in a "do nothing st
-
Hi Guys, I have configured RFC receiver with load balancing and it is giving errors with respect to message server I have given message server name as he host name or it is is like SID+hostname ? Message server service = sapms+SID and Logon group = P
-
What about including the version number in the package report?
Here's a simple suggestion - can we include the file version in the report that's created when you package files? Shouldn't be too hard to add something like: ADOBE INDESIGN CS6 PRINTING INSTRUCTIONS FOR SERVICE PROVIDER REPORT Or PUBLICATION NAME: 0