Air cards and Time capsule can it work

I currently connect to the internet via an air card specifically Sierra wireless with a usb connection. Can I make my Time capsule work with this configuration. If so how can I hook this up so that it works properly.

I have an equally complex setup with a managed switch actually but I have never seen the TC have this kind of issue.
What I do notice is you have changed the TC from defaults.. you are using a non-default IP range.
I have run across issues like this where people move things from default.
I would like you to start over.. factory reset the TC. That will set it back to default router mode.
Do the min setup on the TC..
1. Change all names from what you were using. That includes the TC name and wireless name/s
Make them short, no spaces and pure alphanumeric because that is the correct way to network. Apple default names with spaces and apostrophes are fundamentally bad.
2. With just the TC plugged into the switch.. and a single computer connected by ethernet. Power cycle the whole network.. this allows the switch to clear all the old MAC address.
3. Test on the computer just ethernet. Turn the wireless off.
The computer must use dhcp and must get an ip from the TC.
It has to get the correct Router.. ie Gateway.. I wish apple could stick with proper network terminology.
And it must get same address or valid DNS server address/es.
If it fails.. please plug ethernet directly to the TC.. bypassing the switch.
You should get the standard IP addressing and internet connection.
If not please post the screenshot from the Mac of the network preferences showing the ethernet setup.
I need to see what address it does get. I need you to make sure the ethernet is the TOP of the list. So rearrange the order of network connection. With the airport off it should just go to the top of the list.
If it appears to be working .. but a browser cannot connect, open a terminal and ping an internet address.
Ping the actual gateway address the ISP gives you and ping the ISP dns address.

Similar Messages

Loaded Mountain Lion and time capsule no longer works, airport utility can't be configured, back ups have stopped, sparse bundle in use errors occur, what a mess!!!!

Should Airport Utility now be defunct for my time capsule because I have upgraded OS to Mountain Lion? I have tried every fix I can think of but AU will not set up. I'm also getting repeated time machine back up failures and now I have a new "sparsebundleinuse" error which is totally useless to me, I have no idea what a sparse bundle is, I have no idea what it's suddenly being used by and there's no information to say what to do about it. Apple is killing me here!!!

I've tried to but on the install for Airport Utility 6, after the download I get through the introduction then the license then I get "airport utility can't be installed on this disk. The version of Mac OS X on this volume is not supported" and that's it, no more options!?

Two Mac Computers and Time Capsule can't network all

I have two Mac computers, a Mac Mini and a MacBook Pro. I also have a Time Capsule. For some reason I can only connect from my Mac Mini to the MacBook Pro, but not from the MacBook Pro to the Mac Mini. On the MacMini, when I go to Go menu in the finder and then Network, I see the Time Capsule and the MacBook Pro. If I want to go the other way MacBook Pro to the MacMini all I see when I go to Go menu in the finder and then Network, is the Time Capsule. I have searched all over the internet to find an answer to fix the problem but I have not found anything. Help! Please.

Well, I wrote my question at 2am after hours of experimentation. The next day all seems well. It seems changing the broadcast frequency worked, but they needed time to decide they liked each other. I wish I'd known that 6 months ago! It was weird because when I first plugged the time capsule on this time it seemed the MacBook detected it just fine. Then I worked to get the internet connection going and it all went sideways. Very mysterious. Thanks for reading.

Best way to extend wireless via airport express and time capsule

best way to extend wireless via airport express and time capsule
i live in a two storey house where i use my airport express to create a wireless network in the main floor, and time capsule to extend it in the upper floor, where my room is. i have like 16 mbps in the main floor, and 2-3 mbps in the upper floor after having speediest.
i used time capsule in the upper floor because i use wireless backup daily and don't want to put internet down while i im doin it and consequently my parent can have internet access in the main floor, am i right? or do i have make just the opposite in order to have a good internet speed?
secondly, while checking airport express wireless mode on airport utility, there is like 4 different type of radio mode(802 11n bg comp, 802 11n 2.4, 802 11n a comp, 802 11n 5ghz) which i have no idea what they mean
what do you recommend?
we have like iphone4, iphone 3g, mbookpro, ipad, ipad 2, samsung tv and a sony vaio laptop in the wireless network
thank you

What you have would appear to be working but I can comment how I would redefine your setup. Note that both Airport Express and Time Capsule can function as wireless base stations so you do have wireless everywhere and at all times — using the Time Capsules for backups doesn’t mean your parents won’t have internet access regardless of the where the base stations are located.
You appear to have devices to connect to your network that use the 2.4 GHz band with 802.11g such as the iPhone 3G and perhaps the 5 GHz band with 802.11n such as likely the Macbook Pro if it’s a recent model. The iPhone 4 can use 5 GHz and 802.11n. Can’t comment on the Sony and Samsung but you can check their specs.
Now the Time Capsule (if it’s a recent version), can simultaneously supply 2.4 GHz and 5 GHz band signals, but the Airport Express (if it’s recent) can only use one of those bands at one time. Likely the lowest common denominator for your devices is going to be the 2.4 GHz band since the devices that are capable of using 5 GHZ also support 2.4 GHz. If you don’t use 5 GHz, you won’t lose much in a two-storey home because likely it’s the 2.4 GHz band is better signal anyway because 5 GHz signals drop off quickly with several walls/floors to penetrate.
You also didn’t mention if the Airport Express is used to support a printer and/or AirPlay (using iTunes to play on remote speakers via the Airport Express connection) but that might also be a factor in the best location to place the Airport Express. Although the printer could be switched between the Time Capsule and the Airport Express if needed, only the Airport Express will support your remote speakers.
Recommend you use the Time Capsule as the Base station. When using Airport Utility to define the network, after you name your network, etc., select the Wireless tab, check the box “Allow this network to be extended” and set the Radio Mode to "802.11n (802.11b/g compatible)”.
Using the Airport Utility, click on the Airport Express; after you define the device and network name, select the Wireless tab, define the Wireless Mode as “Extend a Wireless Network” and check the box “Allow wireless clients”.
Hope that helps.

I have a macbook pro and use BT homehub 3. can't work out how to connect my time capsule. can anyone help, thanks.

I have a macbook pro and use BT homehub 3. can't work out how to connect my time capsule. can anyone help? thanks

Just need to plug the TC in to the hub in bridge mode.. do not try and bridge the homehub.. it is not possible with the setup BT uses.
To bridge the TC.. plug it directly into a computer by ethernet.. no other connection to the TC or the computer.
Press and hold in reset until the front LED flashes rapidly.. about 10sec.
Release the reset.
Open the airport utility and setup the TC to bridge mode.
The actual method depends on version of the OS and airport utility you use.
This is version 5.
Sorry I cannot post the v6 as I am on a snow leopard computer now. But you go to the network tab, and choose off bridge mode for method of connection. It will be NAT and dhcp by default.
Then setup wireless.. you have a number of choices here.
Either setup with the same SSID Security and password, as the homehub uses.. or a different name, and password..
Each method works fine.. but you sometimes have issues with wireless channels.. for now leave it on auto and see what happens.. if you have issues lock down the radio channels on both devices.. use one out of the following on each, 1, 6, 11 or 13 in UK.. so say 6 on the homehub then 13 onthe TC.
Update the TC.. unplug fromt the computer and plug it into the homehub.
If you have other issues with the setup tell us what OS you run so we can post suitable screenshots.

I have an existing new belkin modem router which works fine with quite a few wired and wireless products in my house. My question is if i buy a time capsule can i put it in another room and wirelessly connect it to the belkin modem router, I would then ju

I have an existing new belkin modem router which works fine with quiet a few wired and wireless products in my house. My question is if i buy a time capsule can i put it in another room and wirelessly connect it to the belkin modem router, I would then just like my macbook pro and (imac future purchase) to wirelessly back up to it???????????

Your will need to perform a Factory Default Reset on the TIme Capsule to clear out the current network settings and then reconfigure it to "join" your wireless network using the AirPort Utility setup application.
To perform the Factory Default Reset on the Time Capsule....
Pull the power cord from the back of the device
Wait a few moments
Hold in the reset button on the back of the Time Capsule and keep holding it an additional 8-10 seconds while you simultaneously plug the power cord back in to the Time Capsule
Release the reset button after the hold period and allow 25-30 seconds for the Time Capsule to restart to a slow, blinking amber light
On your Mac.....
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click Continue
Follow the guided setup and choose the "join" option when it appears duriing the setup
You will need to know the exact type of wireless security that the Belkin router is using to enter this information during the setup of the Belkin. Otherwise, the Time Capsule cannot join the network, and you will receive an error message after the configuration process.

Time Capsule does not work and i can not not mount it anymore, even after follow all apples instructions at FAQs

My Time Capsule suddenly stopped working, and i can not even mount it anymore. When i ask for a backup, the time machine keeps looking for a disk with no success.
I tried all the FAQs suggestions:
1) I change the name of the disk using Airport Utility;
2) I updated it using Airport Utility.
Now i can not even try to erase the disk because after to update it, the disk in not listed anymore.
Now i can just read a "internal disk needs repair" message. that wasn't there before, having in mind that the first response was "there is no space at the disk for a backup".
What can i do?

The TC has a fault..
Power it down and let it cool off overnight. Power it on again the next morning and check if it works.. no luck factory reset.. do all the tests quickly as you have 10-20min before the Temp rises to kill it again.
No luck it is dead.. give us the actual model number.. A1xxx from the base.
How old is it?? Beyond 3years they do become dodgy.

Time Machine and Time Capsule don't seem to work well together?

Reposted.
I get the feeling there are some serious problems with the combination of Time Machine and Time Capsule.
This is extremely disappointing, as the idea of a centralized backup device on the network (instead of disks attached to each and every computer we have running Leopard) seemed like such a good idea and a good way to supplement our tape-based backup that takes place with Retrospect.
In reality, it's a disaster on both Intel and PowerPC systems. All systems and the Time Capsule are fully up to date with software updates from Apple. I have two 1TB Time Capsule units. It goes something like this:
1. I have a few systems (mainly Intel) that work perfectly with the Time Capsule. There are no complaints and no issues at all. These systems just quietly run their backups as they should. They are the definite minority--maybe one or two have worked properly.
2. I have some systems that complain from time to time (mainly PowerPC) but will back up with a little encouragement. These too are the minority.
3. And finally, I have systems that are nothing but pain. These are both Intel and PowerPC systems. They are also the majority of the systems I have. The most common problem is sudden loss of the credentials needed to access the Time Capsule hardware--a user will be going along about their business when the Mac OS asks for the Time Capsule user name and password--after it's already been supplied and backups have been running. This should simply never ever happen.
Another charming behavior I've seen is corruption of the sparse disk image file that each computer creates on the Time Capsule. Time Machine will complain that it can't perform the backup, and examining the disk image file with Disk Utility shows it to be severely damaged. Turning off Time Machine, deleting the corrupted sparse image file, and starting over fixes it. For a while.
Finally, there are the machines (again, both Intel and PowerPC) that just can't seem to actually get through the first backup run. They either go so far and can't continue, or never actually manage to get started. I've checked the disks in these computers and found no problem with the hardware or file system. The installations are fresh and fully up to date.
Meanwhile, I have computers running Leopard with directly attached disks configured for use with Time Machine. One is a QuickSilver that isn't even officially supported by Leopard, with a Firewire attached disk. It doesn't skip a beat. The other is an Intel Mac mini being used with Mac OS X Server 10.5.4 and a USB external hard drive. These machines just do their thing, and I never have to babysit them.
These problems with the Time Capsule have been so severe that I've just given up on most of the computers and shut off Time Machine entirely. We have tape backups that run over the week, so it's not a huge loss. But that's not what really made me throw up my hands and say "enough"...no, that was the speed. Even with just one computer backing up to it, the Time Capsule seemed terribly slow. Watching the progress indicator was just painful.
I put in a word about all of this to my independent Apple dealer, and they say I'm definitely not the first to complain about some or all of these problems. In fact, they told me they were going to set up a test lab in their shop to see if they could duplicate these findings. I have no doubt that they can.
There are a total of seven computers backing up to one Time Capsule. They all store maybe ~40GB worth of data including the OS. There are about six computers on the other. Because of the way the network is laid out, the Time Capsule is connected to a Gigabit switch (and that is the only thing it's connected to). It cannot be used as the router, although I know Apple suggests this. The Airport section is disabled--I have no need or desire to use it. Some computers link up at 100 megabits, others at 1 gigabit. There are no network problems--we have no problems moving large amounts of data across the same network to our tape backup machine.
Is anyone else seeing these kinds of problems? Am I doing something wrong or expecting too much from Time Capsule?

I may be on to something. The Time Capsules I have live in a telephone equipment room that is indoors but not directly air conditioned or heated. It doesn't ever get too hot to be comfortable in there--the highest I've ever seen the temperature was 80 degrees (F). Most of the time the temperature is between 60-78 degrees.
I happened to touch one of them the other day while it was in use, and I noticed that the casing was hot to the touch...not dangerously so I suppose, but much hotter than I would have expected.
So I turned a small fan on both Time Capsules and have left it running. And I've noticed that not only do backups seem to complete more quickly, the reliability is also better. I am going to try some of my most troublesome computers once again just to see what happens.
I know there is a fan pointed at the hard drive in the Time Capsule, but I can't see how it does much in the way of cooling things down. In my opinion, it's just surrounded by too many heat producing devices to do much good...after all, not only is there a 7200 RPM hard disk in there, but also a 500MHz Marvell processor and radio set.

Macbook Air and Time Capsule

I have my air connected to time capsule with an ethernet cable/usb adapter. I cannot connect to it directly. I can only connect if the time capsule is connected to the internet with the ethernet cable, and it doesn't need to be connected via usb.
I am trying to use time capsule as a HD, and wanted to have imovie / idvd files on it, but imovie will not read it.
I do have TC passworded.
Any thoughts?

Thank you.
So, to conclude, it is not possible to use TC with imovie, in any manner, even if I had a disk image on TC, and put my files on the disk image. Therefore, no need to try to make a disk image and mount it, if in the end it won't work for imovie.
It would seem that the imovie programmers should find a way to make it as friendly as iphoto or aperture, both of which can open files from the Time Capsule. I can even open IDVD files directly from TC!
So, if this is the case, I thank you for your answers, and I will mark this as answered.
No one at apple support could resolve this question. One rep told me to use a usb cable to connect from the TC to the mac air, which didn't work either. I'll be returning that cable!
Thanks for the help!

Hi.. I'm new to mac, I've got a mac book air and time capsule is it possible to save music,video from iTunes Store directly to time capsule leaving my 128GB Mac free? If so please help..

Hi.. I'm new to mac, I've got a mac book air and time capsule is it possible to save music,video from iTunes Store directly to time capsule leaving my 128GB Mac free? If so please help..

You can move your iTunes library.. Apple have explicit instructions to do it. If the library is moved to the TC and accessed over wireless, the efficiency of the whole system will drop dramatically..
A file you download goes.. Modem---TC--Laptop--Back to TC--Store on disk. Double looping the wireless slows it dramatically..
As far as using TC for your iTunes.. you CAN.. but SHOULD YOU?
Store files on the TC.
https://discussions.apple.com/message/24380694#24380694
This is asked several times a day.. obviously people are struggling with their latest SSD being too small.
The TC is not suitable for network file server.. but many people having no choice press it into service as such.
It cannot be partitioned. It was and is and ever shall be a backup device for Time Machine.
Major issues.
1. No backup.. no way Time Machine can backup a network drive. No place to backup to.. So all your files will be at risk. And you will need to buy a third party like CCC to do backup.
2. The TC cannot be partitioned and mixing TM backups and data is not great.
3. The drive is slow to spin up and quick to spin down.. there is no controls.
4. iPhoto in particular can easily corrupt its entire library with wireless networking causing a disconnection to one photo. Even if you do this;;; do not move your photo library... you have been warned!!
5. iTunes will constantly lose connection to the library. The disk is too slow to respond.. itunes on the computer will constantly spit out errors. Even in the midst of streaming the TC can spin down the disk due to caching.
6. Do not use any live files on the TC no matter what else you do.. if you edit files in whatever program the file must be on the local hard disk.
7. The only suitable location for most libraries is a computer. You can plug in an external hard disk.
Read pondini for some work arounds.
Q3 here. http://pondini.org/TM/Time_Capsule.html

I can't connect to the drive on my airport time machine and am receiving the message: "AirPort Time Capsule" can't be opened because the original item can't be found.

Time capsule has been working perfectly for months.
Suddenly I can't connect to the drive on my airport time capsule and am receiving the message: “AirPort Time Capsule” can’t be opened because the original item can’t be found.
Time machine appears to be still backing up (last backup within the last hour), but drive is not visible and I have files stored on it.
I have tried rebooting everything in order as suggested for other issues, anyone got any ideas how to see the drive again??

What OS are you running??
It is very typical Yosemite issue.
1. In airport utility does the TC show up.. if so click it.. and see the summary page which will include its IP address. That is what you are after.
From my screenshot you can see the TC address is 192.168.2.57
It might well show up briefly after a reboot or in ipad / iphone version utility. Yosemite is hopeless. The airport utility hardly works.
2. In Finder use Go, Connect to server.
Type in SMB://192.168.2.57 (replace with IP you discover).
If it is possible it will request a password.. type that in and DO NOT FORGET.. to store it in your keychain.
This will work until the TC changes IP which won't happen if it is main router.. but will happen if it is bridged.. so you need to tell me the whole network setup.
Mavericks is nearly as bad and the above instructions should be universal except I would use AFP instead of SMB. Apparently Yosemite is now totally Windows oriented.

Yosemite and Time capsule not working?

I just started using Yosemite on my mac book pro laptop and my mac desktop. Time machine has been fine on my desktop with my external drive which is plugged into the computer. I had no problem with new backups. But, I can't get time machine to work with my laptop and time capsule. I have another external cloud drive as well, and it will not work with that one now either. First, I can no longer just open up my backups from the folders in the finder like I used to be able to. instead all I see is a disk image with my back up and when I click on it I can not open it and get an error message (see below). Also, it will not back up at all, it give me the other error message in this picture. What is going on here? I am so frustrated. I may just have to go to the genius bar but this is so frustrating.
I also can't even access my back ups now from before even if I go in through the finder window and select the hard drive the back up do to go very far back. Only a few days. I am worried that somehow all of my backups are gone but am hoping that is not the case. It all worked fine before I installed Yosemite. I would appreciate any help or guidance.
For the first image, if I try to back up to time capsule I get the exact same message except it says could not back up to the name of my time capsule drive.

A third-party NAS is unsuitable for use with Time Machine, especially if it's your only backup. I know this isn't what you want to hear. I know that Time Machine accepts the NAS as a backup destination. I know that the manufacturer says the device will work with Time Machine, and I also know that it usually seems to work. Except when you try to restore, and find that you can't.
Apple has published a specification for network devices that work with Time Machine. None of the third-party NAS vendors, as far as I know, meets that specification. They all use the incomplete, obsolete Netatalk implementation of Apple Filing Protocol.
If you want network backup, use as the destination either an Apple Time Capsule or an external storage device connected to another Mac or to an 802.11ac AirPort base station. Only the 802.11ac base stations support Time Machine, not any older model.
Otherwise, don't use Time Machine at all. There are other ways to back up, though none of them is anywhere near as efficient or as well integrated with OS X. I don't have a specific recommendation.
If you're determined to keep using the NAS with Time Machine, your only recourse for any problems that result is to the manufacturer (which will blame Apple, or you, or anyone but itself.)

I have two time capsules, one for work and one for home, how do I set up the work time capsule to only back up my work files?

I have two time capsules, one for work and one for home, how do I set up the work time capsule to only back up my work files? Also, how do I add co-workers to my work time capsule and wife to my home time capsule? Thank you!

You cannot have two different TC setups.. at least until Mountain Lion.. it did introduce some changes but I am not sure if you can setup two different configurations for TM.. you can use two different devices to back up to. I doubt this will help you.
You might be better using a real backup software.. superduper, CCC, chronosync etc.
The TC by default is available to any Mac in the network to do backups. TM will sort itself out and put each computer on a different backup. These are kept in separate sparsebundles.. so that is all fine.

Wireless connection between D-Link WiFi router and Time capsule stopped working

We have an ISP provided D-Link wireless router (DIR-615) to which we wirelessly connected our 2Tb Time Capsule for back up and to connect a USB printer to out network. This worked perfectly for 3 1/2 years, until about a month ago, when the time capsule suddenly decided to go "off line". ie we could no longer access it or the printer via our wireless network. We had changed nothing - just one day it stopped working.
We tried to get it back online with no success. As the 2Tb Time Capsule was almost 7 years old and had had some HDD issues in the passed, we figured it had got old and died and that it was time to replace it; so we bought a new 3Tb Time Capsule, thinking this would get everything back to normal.
However much as we tried, we were also unable to get the new 3Tb Time Capsule to connect wirelessly to the D-Link wireless router. The Airport Utility did not show the D-Link wireless router or its wireless network, although we were (and are) able to see it in Systems Preferences>Networks from all our multiple devises. This in itself seemed odd. No matter what we tried, the Airport Utility would not find the D-Link wireless router and hence we could not add the 3Tb Time Capsule to the existing wireless network.
At the end of the day we got fed up with trying to add the 3Tb Time Capsule to the D-Link wireless network, and connected it via a LAN cable to the D-Link router instead. We then set it up as its own network. Worked gerat. Having done that we thought maybe the old 2Tb Time Capsule might not have been the problem after all, so we tried extending our new 3Tb Time Capsule wireless network using the 2Tb Time Capsule wirelessly. This worked perfectly! And we are now almost back to what we wanted.
So although we have a work around, this means now have 2 separate wireless networks as opposed to the original single wireless network where everything talked to everything else.
Can anyone shed any light on any of the following:-
1. Why the original wireless network connection between the D-Link router and the 2Tb Time Capsule just stopped working? Was there some software change from Apple that "decided" D-Link wireless routers were no longer secure; and therefore the TCs could no longer connect to them?
2. Why it was not possible to extend the existing D-Link wireless network using the the new 3Tb Time Capsule?
3. Is there is anyway that we can get back to a single wireless network based around the D-Link wireless router as the primary router connecting to the modem, where the 2 Time Capsules connect as "wireless satellite base stations"?

1. Why the original wireless network connection between the D-Link router and the 2Tb Time Capsule just stopped working? Was there some software change from Apple that "decided" D-Link wireless routers were no longer secure; and therefore the TCs could no longer connect to them?
A firmware update to the TC came along and you agreed to it without perhaps even noticing.. it then smashed your setup because Apple do not recommend the setup you were using and it is very poor.
2. Why it was not possible to extend the existing D-Link wireless network using the the new 3Tb Time Capsule?
Because it is such a poor setup that Apple have taken away your ability to choose it unless you know exactly what you are doing.
3. Is there is anyway that we can get back to a single wireless network based around the D-Link wireless router as the primary router connecting to the modem, where the 2 Time Capsules connect as "wireless satellite base stations"?
Yes, this I can help you with.
I have several ways around the problem.. but the first one is.. why use the DIR-615 at all.. it is not a modem.. it is a very ordinary bottom end, poor single band slow wireless router.
Why don't you simply remove the DIR-615 from the network completely.. plug whatever it is the ISP supplies you.. an ethernet connection from whatever that modem is you mentioned into the WAN port of the Time Capsule. And use the TC in some router mode.. same as the DIR-615 was setup.. dhcp or pppoe or whatever.. I doubt the TC cannot match it.
If you have issues please post a few screenshots from the DIR-615 to show how it is setup from the WAN side.. and as long as you are given the username and password or whatever the ISP uses to authenticate then chuck out the DIR-615.
Tell me if that is a goer.. if not we can work out a few other methods..
eg. Simply turn off the wireless in the DIR-615. It is poor cf the TC and there is no need for it.. with the TC in bridge only use the TC for wireless as well as wireless extend with your old TC.
Or setup roaming network where everything uses the same SSID.
Then you will have one wireless network. And it won't matter what as long as it connects.. although IMHO this is not right as the TC is such a superior router now you are wasting your new TC.

Will the airport devices and time capsule work with telstras mobile hotspot (Sierra Wireless AirCard 753S Mobile Hotspot)??

will the airport devices and time capsule work with telstras mobile hotspot (Sierra Wireless AirCard® 753S Mobile Hotspot)??

Yes. There are 2 ways you could use these devices:
Wirelessly 'join' the network. This would be slower and doesn't offer extending functionality.
Use an Ethernet cable (through Powerline if you can't run a cable). This is faster and offers extending functionality. I would recommend using Bridge Mode if possible.

Air cards and Time capsule can it work

Similar Messages

Maybe you are looking for