AIR-CT5508 wont upgrade to 7.6

Hi,
I wanted to see if anyone has had issues with upgrading to 7.6 images on their AIR-CT2504 or AIR-CT5508.  I have one unit in the lab that refuses to update and I had a customer call me today with the exact same issue.  Maybe someone from TAC has info if other users are having the same problems and can identify if this is an issue with 7.6 and to steer clear for the time being?
Logs:
(Cisco Controller) >
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 7.0.112.21
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
<output omitted>
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >show boot
Primary Boot Image............................... 7.4.110.0 (default) (active)
Backup Boot Image................................ 7.3.101.0
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >!loading AIR-CT5500-K9-7-6-110-0.aes in the GUI now
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >show boot
Primary Boot Image............................... 7.6.110.0 (default)
Backup Boot Image................................ 7.4.110.0 (active)
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >!reloading from GUI now
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
Updating license storage ...  Done.
Restarting system.
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 1.3 (SN: FCW1709L09H, Type: AIR-CT5508-K9) (G)
Verifying boot loader integrity... OK.
OCTEON CN5645-NSP pass 2.1, Core clock: 600 MHz, DDR clock: 330 MHz (660 Mhz data rate)
FPGA Revision 1.7
Env FW Revision 1.8
USB Console Revision 2.2
CPU Cores:  10
DRAM:  1024 MB
Flash: 32 MB
Clearing DRAM........ done
Network: octeth0', octeth1
  ' - Active interface
  E - Environment MAC address override
CF Bus 0 (IDE): OK
IDE device 0:
 - Model: STEC M2T CF 1.0.0 Firm: K1367MIX Ser#: STIM2MB513071013409
 - Type: Hard Disk
 - Capacity: 977.4 MB = 0.9 GB (2001888 x 512)
Press <ESC> now to access the Boot Menu...
Loading primary image (7.6.110.0)
100%
36110929 bytes read
Launching...                              <-- Right here it gives no error, just wont load 7.6 and moves to secondary image
Loading backup image (7.4.110.0)
100%
34513219 bytes read
Launching...
init started: BusyBox v1.6.0 (2010-05-13 17:50:10 EDT) multi-call binary
starting pid 821, tty '': '/etc/init.d/rcS'
/etc/init.d/rcS: line 4: /mnt/bootsys/.core: not found
route: SIOC[ADD|DEL]RT: Network is down
mount: mounting /dev/cfa1 on /mnt/bootsys failed
Set PLX switch MPS settings .............!!!!!!!
Detecting Hardware ...
set smp_affinity for irq 48
003f
DP from CGE5.0 ...
starting pid 1071, tty '/dev/ttyS0': '/usr/bin/gettyOrMwar'
Setting up ZVM
Exporting LD_LIBRARY_PATH
Cryptographic library self-test....passed!
XML config selected
Validating XML configuration
Read HA Config before validation
octeon_device_init: found 1 DPs
readCPUConfigData: cardid 0x6070001
Cisco is a trademark of Cisco Systems, Inc.
Software Copyright Cisco Systems, Inc. All rights reserved.
Cisco AireOS Version 7.4.110.0
Firmware Version FPGA 1.7, Env 1.8, USB console 2.2
Initializing OS Services: ok
Initializing Serial Services: ok
Initializing Network Services: ok
Initializing Licensing Services: ok
License daemon start initialization.....
License daemon running.....
Starting Statistics Service: ok
Starting ARP Services: ok
Starting Trap Manager: ok
Starting Network Interface Management Services: ok
Starting System Services: ok
Starting FIPS Features: ok : Not enabled
Starting Fastpath Hardware Acceleration: ok
Starting Fastpath Console redirect : ok
Starting Fastpath DP Heartbeat : ok
Fastpath CPU0.00: Starting Fastpath Application. SDK-1.8.0, build 269. Flags-[DUTY CYCLE] : ok
Fastpath CPU0.00: Initializing last packet received queue. Num of cores(10)
Fastpath CPU0.00: Init MBUF size: 1856, Subsequent MBUF size: 2040
Fastpath CPU0.00: Core 0 Initialization and FIPS self-test: ok
Fastpath CPU0.00: Initializing Timer...
Fastpath CPU0.00: Initializing Timer...done.
Fastpath CPU0.00: Initializing Timer...
Fastpath CPU0.00: Initializing NBAR AGING Timer...done.
Fastpath CPU0.01: Core 1 Initialization and FIPS self-test: ok
Fastpath CPU0.02: Core 2 Initialization and FIPS self-test: ok
Fastpath CPU0.03: Core 3 Initialization and FIPS self-test: ok
Fastpath CPU0.03: Received instruction to get link status
Fastpath CPU0.04: Core 4 Initialization and FIPS self-test: ok
Fastpath CPU0.05: Core 5 Initialization and FIPS self-test: ok
Fastpath CPU0.06: Core 6 Initialization and FIPS self-test: ok
Fastpath CPU0.07: Core 7 Initialization and FIPS self-test: ok
Fastpath CPU0.08: Core 8 Initialization and FIPS self-test: ok
Fastpath CPU0.09: Core 9 Initialization and FIPS self-test: ok
Starting Switching Services: ok
Starting QoS Services: ok
Starting Policy Manager: ok
Starting Data Transport Link Layer: ok
Starting Access Control List Services: ok
Starting System Interfaces: ok
Starting Client Troubleshooting Service: ok
Starting Management Frame Protection: ok
Starting Certificate Database: ok
Starting VPN Services: ok
Starting Licensing Services: LICENSE_PRINT:cnfgrCslLicense:ERROR:license request Failed for units: 500 rc:User failed to accept EULA
ok
Starting Redundancy: ok
Starting LWAPP: ok
Starting CAPWAP: ok
Starting LOCP: ok
Starting Security Services: ok
Starting Policy Manager: ok
Starting Authentication Engine: ok
Starting Mobility Management: ok
Starting AVC Services: ok
Starting Virtual AP Services: ok
Starting AireWave Director: ok
Starting Network Time Services: ok
Starting Cisco Discovery Protocol: ok
Starting Broadcast Services: ok
Starting Logging Services: ok
Starting DHCP Server: ok
Starting IDS Signature Manager: ok
Starting RFID Tag Tracking: ok
Starting RF Profiles: ok
Starting Power Supply and Fan Status Monitoring Service: ok
Starting Mesh Services:  ok
Starting TSM: ok
Starting CIDS Services: ok
Starting Ethernet-over-IP: ok
Starting DTLS server:  enabled in CAPWAP
Starting CleanAir: ok
Starting WIPS: ok
Starting SSHPM LSC PROV LIST: ok
Starting RRC Services: ok
Starting SXP Services: ok
Starting Alarm Services: ok
Starting FMC HS: ok
Starting IPv6 Services: ok
Starting Config Sync Manager : ok
Starting Hotspot Services: ok
Starting PMIP Services: ok
Starting Portal Server Services: ok
Starting mDNS Services: ok
Starting Management Services:
   Web Server:    CLI: ok
   Secure Web: ok
   License Agent: ok
(Cisco Controller)
Enter User Name (or 'Recover-Config' this one-time only to reset configuration to factory defaults)
User:  admin
Password:*****
User:admin
Password:********
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 7.0.112.21
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
<output omitted>
! Now If i try the FUS file AIR-CT5500-K9-1-9-0-0-FUS.aes it completes successfully and i reload from the GUI
(Cisco Controller) >
(Cisco Controller) >Restarting system.
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 1.3 (SN: FCW1607L035, Type: AIR-CT5508-K9) (G)
Verifying boot loader integrity... OK.
OCTEON CN5645-NSP pass 2.1, Core clock: 600 MHz, DDR clock: 330 MHz (660 Mhz data rate)
FPGA Revision 1.7
Env FW Revision 1.8
USB Console Revision 2.2
CPU Cores:  10
DRAM:  1024 MB
Flash: 32 MB
Clearing DRAM........ done
Network: octeth0', octeth1
  ' - Active interface
  E - Environment MAC address override
CF Bus 0 (IDE): OK
IDE device 0:
 - Model: STEC M2T CF 1.0.0 Firm: K1367MIX Ser#: STIM2MB513071013409
 - Type: Hard Disk
 - Capacity: 977.4 MB = 0.9 GB (2001888 x 512)
Press <ESC> now to access the Boot Menu...
Loading primary image (7.6.101.2)
100%
6394630 bytes read
Launching...
Loading backup image (Image not found)
** Unable to read "linux.bak.img" from ide 0:2 **
** Launch failure  **
============================================================
 Boot Loader Menu
============================================================
 1. Run primary image (7.6.101.2) - Active
 2. Run backup image (Image not found)
 3. Change active boot image
 4. Clear configuration
 5. Format FLASH Drive
 6. Manually update images
!Now i am stuck in the Boot Loader menu and the unit wont even boot up.  I used the RTOS files and recovered the unit several times trying to upgrade multiple ways but no matter what i try the unit will not boot with 7.6.  It works perfectly fine with 7.4. 
Anyone have ideas?
Known issue?
Other links with what seems like the same issue:
https://supportforums.cisco.com/pt/discussion/12130001/air-ct2504-upgrade-failure
https://supportforums.cisco.com/discussion/12060686/wlc-5508-upgrade-software-76
http://omgili.com/thread/.wHSUbtEfZS6sY9oec8tRj1DNafRV3e2EmgIsn2U7n.0aLwe7IPHyQaQO5o5MalitJoQnElOrK8-/

Just to add to this, we hit the same problem with a 5508.  Cisco TAC sent us the RTOS image which re-installed 7.0.116.0 firmware, however every time I run the 1.9.0.0 FUS I see the same problem: it's fully repeatable.  I'm fully aware of the instruction not to run the FUS more than once and my first thought was that I had done that, however this unit has been in a data centre since before FUS 1.9.0.0 came out so I know that it hasn't had that installed.  However we may well have installed FUS 1.7.0.0 - is it possible that having installed 1.7 then the 1.9 version screws it?  A question for my TAC contact...
I've run the RTOS recovery now and I'm installing the 7.6.110.0 firmware, without re-running the FUS.
The currently installed Feild Recovery Version is 7.0.112.21 which looks like the pre-FUS 1.9.0.0 version...maybe the FUS is faulty.

Similar Messages

  • AIR-CT5508-K9 License gone after upgrading to 7.4.100.0

    We have a wierd issue with our 5508 WLC which has a AP base count of 250.
    right now we're running code version 7.4.100.0 with 75 active AP's connected
    The license details:
    I tried twice to upgrade to code version 7.5.102.0 but in both cases the base license disappeared after the upgrade as you can see:
    (Cisco Controller) >show license all 
    License Store: Evaluation License Storage
    StoreIndex:  0  Feature: base-ap-count                     Version: 1.0
            License Type: Evaluation
            License State: Active, Not in Use, EULA not accepted
                Evaluation total period:  8 weeks  4 days
                Evaluation period left:  8 weeks  4 days
            License Count: 500 / 0 (Active/In-use)
            License Priority: None
    (Cisco Controller) >show license udi        
    Device# PID                     SN                      UDI
    *0      AIR-CT5508-K9           FCW1526xxxx            AIR-CT5508-K9:FCW1526xxx
    (Cisco Controller) >show license file
    License Store: Evaluation License Storage
      Store Index: 0
        License: 11 base-ap-count 1.0 LONG TRIAL DISABLED 1440 DISABLED STANDALONE
                  ADD 500_KEYS INFINITE_KEYS NEVER NEVER NiL SLM_CODE DEMO NiL NiL
                  Ni NiL NiL 5_MINS NiL MdJd10O,mtIZ6NbE6Wz4L7mlRpB1ORkKam6zeH6MTA
                 f:ANiieo1Z<---cut--->5lF03hp
                 csLJVYkat3KCLOPYJNrPo3H6kt5cbt8q4XJ46naeRqwInXo3s+nsLU7rOtdOxoIxY
                 ZAo3LYmUJ+MFzsqlhKoJVlPyEvQ8H21MNUjVbhoN0gyIWsyiJaM8AQIkVBQFzhr10
                 GYolVzdzfJfEPQIx6tZ++/Vtc/q3SF/5Ko8XCY=</WLC>
        Comment:
           Hash: 4RHF2Mhn<---cut--->w3KFoVG4=
    therefor we're unable to connect AP's anymore.
    did not find any bug related to that issue or any information in the releasenote which could explain that behaviour.
    any ideas?

    Thanks that helped me out. I contacted cisco license team and they sent me a custom license file.
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.5.102.0
    Bootloader Version............................... 1.0.16
    Field Recovery Image Version..................... 7.0.112.21
    Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
    Build Type....................................... DATA + WPS
    System Name...................................... xxxxx
    System Location.................................. Zuerich
    System Contact................................... xxxxx
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
    Redundancy Mode.................................. Disabled
    IP Address....................................... xxxxx
    Last Reset....................................... Software reset
    System Up Time................................... 0 days 0 hrs 7 mins 19 secs
    System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin, Rome, Vienna
    System Stats Realtime Interval................... 5
    System Stats Normal Interval..................... 180
    Configured Country............................... CH  - Switzerland
    Operating Environment............................ Commercial (0 to 40 C)
    --More-- or (q)uit
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +43 C
    External Temperature............................. +26 C
    Fan Status....................................... OK
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 4
    Number of Active Clients......................... 8
    Burned-in MAC Address............................ 30:F7:0Dxxxxxx
    Power Supply 1................................... Present, OK
    Power Supply 2................................... Present, OK
    Maximum number of APs supported.................. 250
    (Cisco Controller) >show license all
    License Store: Primary License Storage
    StoreIndex:  2  Feature: base                              Version: 1.0
            License Type: Permanent
            License State: Active, Not in Use
            License Count: Non-Counted
            License Priority: Medium
    License Store: Primary License Storage
    StoreIndex:  3  Feature: base-ap-count                     Version: 1.0
            License Type: Permanent
            License State: Active, In Use
            License Count: 250 /250 (Active/In-use)
            License Priority: Medium
    License Store: Evaluation License Storage
    StoreIndex:  0  Feature: base-ap-count                     Version: 1.0
            License Type: Evaluation
            License State: Inactive
                Evaluation total period:  8 weeks  4 days
                Evaluation period left:  8 weeks  4 days
            License Count: 500 / 0 (Active/In-use)
            License Priority: None
    --More-- or (q)uit

  • I have a mac book pro with ocx snow leopard I wont upgrade to what?

    I have a mac book pro with osx snow leopard I wont upgrade to what?

    OS X Mountain Lion system requirements
    To install Mountain Lion, you need one of these Macs:
    iMac (Mid 2007 or newer)
    MacBook (Late 2008 Aluminum, or Early 2009 or newer)
    MacBook Pro (Mid/Late 2007 or newer)
    MacBook Air (Late 2008 or newer)
    Mac mini (Early 2009 or newer)
    Mac Pro (Early 2008 or newer)
    Xserve (Early 2009)
    Your Mac needs:
    OS X v10.6.8 or OS X Lion already installed
    2 GB or more of memory
    8 GB or more of available space

  • AIR-LAP1242G-E-K9 do not work with AIR-CT5508-K9 while AIR-LAP1142N-E-K9 do

    Hello,
    we do have a site where we need to deploy AIR-LAP1142N-E-K9 and AIR-LAP1242G-E-K9 APs. We have two AIR-CT5508-K9 controllers with SW version                  6.0.188.0.
    AIR-LAP1142N-E-K9s work okay, as expected, we do not have any problems with them.
    However AIR-LAP1242G-E-K9s do not, there is a problem with establishing CAPWAP tunnel with the controller.The AP is seen on the controller for a while, with 0 time up-time, cannot change any settings on the AP via controller, and after a while it disapears from the controller, apears again and this repeats.
    The APs and controllers are connected to the LAN campus.
    Controllers via two 1G links configured as Etherchannel to WS-C6506-E VSS switch with s72033-ipservicesk9_wan-vz.122-33.SXI1.bin on it.
    APs to WS-C3750G-48PS with c3750-ipbasek9-mz.122-50.SE2.bin on it. 3750 is connected to the C6505 via two 1G links configured as Etherchannel.
    Below I copied the log I captured on 1242 and the controller. Highlighted ones are the ones which I think might bring a clue.
    I performed some troubleshooting steps.
    - As we have some other controllers available over WAN, I  tested the 1242 AP  with 2100, 4400 and also with the same model AIR-CT5508-K9 with SW version                  6.0.188.0 over WAN and this worked always okay.
    - I wanted to be sure that I eliminate any kind of out of sequence packet issue, so I brought down all redundancy L2 links so that the L2 path from the AP to the controller was only through one leg links.
    - I also brought the second controller down to eliminate potential issue with having two of them up.
    - The AP gets its IP from DHCP configured on the C6506 switch, I am always able to ssh to AP, so the IP connectivity does not seem to be an issue.
    - I have more 1242s, all behave in the same way. I also connected them to some other 3750 switches we have in the campus, always the same.
    - As this seems to be maybe a kind of ssl issue, I tried to play with controller settings, like enabling Accept... options  under Security/AP Policy,but this did not help.
    - I also tried to reboot the controller, no improvement.
    - The APs came from the factory, so in the beginning everything was factory default in them. They were always able to download the image from the controller in the very initial phase. I still do have some of them untouched, so I can perform any troubleshooting steps with the fresh one.
    I can reproduce this, can also send debugging logs if needed.
    Any idea on what could be wrong is highly appreciated.
    Thank you.
    +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    This Discussion has been converted into document:- https://supportforums.cisco.com/docs/DOC-23054
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    AIR-LAP1242G-E-K9 10.0.13.28 log
    *Mar  1 00:00:05.922: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.536: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot1 1Radio 0
    *Mar  1 00:00:07.672: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 304 messages)
    *Mar  1 00:00:09.809: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
    *Mar  1 00:00:09.874: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2009 by Cisco Systems, Inc.
    Compiled Mon 02-Nov-09 18:42 by prod_rel_team
    *Mar  1 00:00:09.874: %SNMP-5-COLDSTART: SNMP agent on host wuen4028 is undergoing a cold start
    *Mar  1 00:00:09.964: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Mar  1 00:00:09.967: bsnInitRcbSlot: slot 1 has NO radio
    *Mar  1 00:00:10.191: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:10.191: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:10.430: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:10.818: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    *Mar  1 00:00:11.212: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:18.315: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.0.13.28, mask 2 55.255.255.0, hostname wuen4028
    *Mar  1 00:00:28.988: Logging LWAPP message to 255.255.255.255.
    *Mar  1 00:00:31.456: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:00:31.495: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:32.457: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:32.457: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
    *Mar  1 00:00:38.810: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:00:47.811: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
    *Mar  1 00:00:56.812: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
    *Mar  1 00:01:07.815: %CAPWAP-3-ERRORLOG: Selected MWAR 'wuen4001'(index 0).
    *Mar  1 00:01:07.815: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Feb 11 07:52:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.13.5 peer_port: 5246
    *Feb 11 07:52:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 11 07:52:25.441: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.0.13.5 peer_port:  5246
    *Feb 11 07:52:25.443: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.13.5
    *Feb 11 07:52:25.443: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 10.0.13.5
    *Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
    *Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.0.13.5
    *Feb 11 07:52:30.441: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.13.5
    *Feb 11 07:52:30.442: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 10.0.13.5
    *Feb 11 07:52:30.443: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
    *Feb 11 07:52:30.443: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Feb 11 07:52:30.443: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.0.13.5
    *Feb 11 07:52:47.644: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Feb 11 07:53:23.999: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.0.13.5:5246
    *Feb 11 07:53:24.000: %CAPWAP-3-ERRORLOG: Selected MWAR 'wuen4001'(index 0).
    *Feb 11 07:53:24.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Feb 11 07:52:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.13.5 peer_port: 5246
    *Feb 11 07:52:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 11 07:52:24.001: %DTLS-5-PEER_DISCONNECT: Peer 10.0.13.5 has closed connection.
    *Feb 11 07:52:24.001: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.0.13.5:5246
    *Feb 11 07:52:24.002: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
    *Feb 11 07:52:24.123: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is not established.
    wuen4028#
    AIR-CT5508-K9 10.0.13.5 log
    *Feb 11 09:00:54.824: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2171 Failed to c
    omplete DTLS handshake with peer 10.0.13.28
                                               *Feb 11 08:59:53.798: %DOT1X-3-MAX_EA
    P_RETRIES: 1x_auth_pae.c:2862 Max EAP identity request retries (3) exceeded for
    client 00:1f:3b:93:dd:4f
    *Feb 11 08:59:51.197: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
    ity request retries (3) exceeded for client 00:c0:a8:e1:b1:71
    --More-- or (q)uit
    *Feb 11 08:59:21.212: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
    rector: Could not find valid channel lists for 802.11bg
    *Feb 11 08:58:39.766: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2171 Failed to c
    omplete DTLS handshake with peer 10.0.13.28
                                               *Feb 11 08:57:06.131: %RRM-3-RRM_LOGM
    SG: rrmChanUtils.c:292 RRM LOG: Airewave Director: Could not find valid channel
    lists for 802.11bg
    *Feb 11 08:56:24.504: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2171 Failed to c
    omplete DTLS handshake with peer 10.0.13.28
                                               *Feb 11 08:55:09.693: %DOT1X-3-MAX_EA
    P_RETRIES: 1x_auth_pae.c:2862 Max EAP identity request retries (3) exceeded for
    client 00:1f:3b:93:dd:4f
    *Feb 11 08:54:51.040: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
    rector: Could not find valid channel lists for 802.11bg
    *Feb 11 08:53:56.493: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
    sions exceeded for client 00:1f:3b:93:dd:4f
    *Feb 11 08:53:34.497: %DTL-3-OSARP_DEL_FAILED: dtl_arp.c:1380 Unable to delete a
    n ARP entry for 10.0.13.28 from the operating system. ioctl operation failed
    *Feb 11 08:52:35.936: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
    rector: Could not find valid channel lists for 802.11bg
    *Feb 11 08:52:26.492: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
    sions exceeded for client 00:1f:3b:93:dd:4f
    *Feb 11 08:50:07.680: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
    sions exceeded for client 00:1f:3b:93:e6:57
    *Feb 11 08:48:37.458: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
    ity request retries (3) exceeded for client 00:1f:3b:93:e6:57
    *Feb 11 08:47:37.438: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
    sions exceeded for client 00:1f:3b:93:e6:57
    *Feb 11 08:47:34.438: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
    ity request retries (3) exceeded for client 00:16:44:1d:0f:53
    *Feb 11 08:46:32.422: %DOT1X-3-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:407 Max EAPOL-ke
    y M3 retransmissions exceeded for client 00:16:44:1d:0f:53
    *Feb 11 08:46:06.790: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
    ity request retries (3) exceeded for client 00:1f:3b:95:61:bd
    *Feb 11 08:46:06.789: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 Authentication abor
    ted for client 00:1f:3b:95:61:bd
    *Feb 11 08:46:06.210: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
    ity request retries (3) exceeded for client 00:1f:3b:93:e6:57
    *Feb 11 08:45:34.304: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
    ity request retries (3) exceeded for client 00:1f:3b:95:61:bd
    *Feb 11 08:45:34.303: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 Authentication abor
    ted for client 00:1f:3b:95:61:bd
    *Feb 11 08:45:01.298: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
    rector: Could not find valid channel lists for 802.11bg
    *Feb 11 08:44:38.076: %SIM-3-PORT_UP: sim.c:9547 Physical port 2 is up!.
    *Feb 11 08:44:38.037: %SIM-3-PORT_UP: sim.c:9547 Physical port 1 is up!.
    --More-- or (q)uit
    *Feb 11 08:44:38.009: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'cliWebInitParms.cfg'
    *Feb 11 08:44:37.980: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'rrcEngineInitParms.cfg'
    *Feb 11 08:44:37.980: %CNFGR-3-INV_COMP_ID: cnfgr.c:2105 Invalid Component Id :
    Unrecognized (81) in cfgConfiguratorInit.
    *Feb 11 08:44:37.928: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'rfidInitParms.cfg'
    *Feb 11 08:44:37.915: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'dhcpParms.cfg'
    *Feb 11 08:44:37.903: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'bcastInitParms.cfg'
    *Feb 11 08:44:37.834: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'rrmInitParms.cfg'
    *Feb 11 08:44:27.331: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'apfInitParms.cfg'                                            
    *Feb 11 08:44:27.226: %MM-3-MEMBER_ADD_FAILED: mm_dir.c:903 Could not add Mobili
    ty Member. Reason: IP already assigned, Member-Count:1,MAC: 00:00:00:00:00:00, I
    P: 0.0.0.0
    *Feb 11 08:44:27.023: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'mmInitParms.cfg'
    *Feb 11 08:44:27.013: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'aaaapiInitParms.cfg'
    *Feb 11 08:44:27.011: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'pemInitParms.cfg'
    *Feb 11 08:44:26.898: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'dot1xInitParms.cfg'
    *Feb 11 08:44:26.868: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'capwapInitParms.cfg'
    *Feb 11 08:44:26.718: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'spamInitParms.cfg'
    *Feb 11 08:44:25.650: %SSHPM-3-FREAD_FAILED: sshpmlscscep.c:1395 Error reading f
    ile /mnt/application/lscca_pem.crt
    *Feb 11 08:44:06.435: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
    figuration file 'sshpmInitParms.cfg'  

    Thanks for such quick response and suggestions.
    Yes, I seem not to to be 100% perfect as for the list of troubleshooting steps I took.
    I had already tried the two commands you mentioned. I tried again, this time with some other 1242, but these do not help.
    Yes, I was already thinking that this could be in theory a licensing issue. The controller is bougth with 25 licenses.
    In the beginnign I had one 1142 on it and tried to enable 1242s which did not work. Now I have five 1142s on it, as this worked okay, I guess it could not be a licensing issue.
    I think that I can see in the log files that the machines communicate to each other, L2 or L3 paths seem to be working okay. I forgot to mention that I am using option 43 on the DHCP server, so the AP clearly finds its way to the controller. What's more both APs and the controllers are in the same VLAN, so they are in the same broadcast domain.
    Below is sho ver from the AP. The AP seems to have Certificate type - manufacture installed, so I guess there should not be a problem with the certificate, especially knowing that the AP works with other controllers over WAN.
    My guess these messages seen on AP especially "Invalid event 38 & state 3 combination" might tell us what's wrong.
    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    *Feb 11 07:52:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
    *Feb 11 07:52:24.001: %DTLS-5-PEER_DISCONNECT: Peer 10.0.13.5 has closed connection.
    *Feb 11 07:52:24.001: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.0.13.5:5246
    *Feb 11 07:52:24.002: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
    *Feb 11 07:52:24.123: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is not established.
    Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2009 by Cisco Systems, Inc.
    Compiled Mon 02-Nov-09 18:42 by prod_rel_team
    ROM: Bootstrap program is C1240 boot loader
    BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
    AP9caf.ca00.1c78 uptime is 17 minutes
    System returned to ROM by power-on
    System image file is "flash:/c1240-k9w8-mx.124-21a.JA2/c1240-k9w8-mx.124-21a.JA2"
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-LAP1242G-E-K9    (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
    Processor board ID FCZ135082GH
    PowerPCElvis CPU at 262Mhz, revision number 0x0950
    Last reset from power-on
    LWAPP image version 6.0.188.0
    1 FastEthernet interface
    1 802.11 Radio(s)
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 9C:AF:CA:00:1C:78
    Part Number                          : 73-11479-01
    PCA Assembly Number                  : 800-30493-01
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC13484GYY
    Top Assembly Part Number             : 800-29589-03
    Top Assembly Serial Number           : FCZ135082GH
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-LAP1242G-E-K9
    Configuration register is 0xF
    AP9caf.ca00.1c78#

  • Webcam not working for Macbook Air 2013 after upgrading to OSX Mavericks? Yahoo/ Google/Skype cam chats not working. Facetime works though. Any updates of Mavericks released to fix this?

    Webcam not working for Macbook Air 2013 after upgrading to OSX Mavericks? Yahoo/ Google/Skype cam chats not working. Facetime works though. Any updates of Mavericks released to fix this?

    I have a MacBook Pro Retina display: 15.4-inch late 2015 with OS X Mavericks install, only on second week. 
    Insight works on FaceTime, Skype, but yahoo program does not show insight cam in dropped down.
    Now when I got my new MacBook Pro, I down loaded all new Skype (worked tested), FaceTime (Worked Tested), Yahoo (not worked)
    Fix:
    With the new Maverick you have to use there messager program Version 8.0 (4218). Once I add my yahoo account video works again.
    It also supported AOL, AIM, Google Talk, Jabber.
    Guess I miss it frist time... hope this helps...

  • Vulnerabilities from WLC - AIR-CT5508-K9

    Hello, Guys
    The follow vulnerabilities were found in my WLC - AIR-CT5508-K9:
    Somebody knows these errors.
    Port: 22/tcp     Running vulnerable SSH service: OpenSSH 4.0.
    Port: 22/tcp     Running vulnerable SSH service. Vulnerable OS: Linux 2.6.15 - 2.6.27.
    Port: 443/tcp     SSLv2 is supported
    Port: 443/tcp     ip(xx.xx.xx.xx):443 negotiated the SSL_RSA_WITH_DES_CBC_SHA.
    Port: 443/tcp     Running vulnerable HTTPS service.
    Port: 443/tcp     TLS/SSL certificate is self-signed.
    Can you help me?
    Thanks,
    Rodrigo

    The first 2, there's nothing to do about it.
    For support of SSLv2 and weak cipher encryption, there are commands for that.
    config network secureweb cipher-option sslv2 {enable | disable}
    The last one just requires you to install a signed certificate on the WLC management.

  • After yesomite upgrade my iPhoto wont upgrade and open

    after yesomite upgrade my iPhoto wont upgrade and open

    Try the following:
    1 - delete the iPhoto preference file, com.apple.iPhoto.plist, that resides in your
         User/Home/Library/ Preferences folder.
    2 - delete the contents the following folder: User/Library/Containers/com.apple.iPhoto
    3 - reboot, launch iPhoto and try again.
    NOTE: For Mavericks and Yosemite,  go to your Home folder and use the View ➙ Show View Options menu to bring the this window:
    where you can check the Show Library Folder checkbox.

  • Apple remote desktop wont upgrade or install

    apple remote desktop wont upgrade or install on yosemite
    Apple store woint let me purchase it either

    Hello and thanks for the reply.
    I tried the original install and the next installer v3.2, then tried to license and update.
    no go on either. The app freezes up on the serial number screen.
    Also when I run the updated from the link I get an error stating I already have a newer version.
    Frank

  • My ipod touch 3g wont upgrade from 4.2.1 to 4.3.3

    while restoring from itunes it wont upgrade from 4.2.1 to 4.3.3 i even upgraded itunes no luck whats wrong i dont understand, please help.

    What happens when you try?
    Error message?
    What does it say?
    Is your ipod the 8GB model?  If so, then it is second gen.

  • AVI plays on iMAC with native SL install, but not  on Air with SL upgrade

    I have an iMAC that I bought with Snow Leopard installed from the outset and a MacBook Air, which was upgraded from Leopard to SL. Both machines have Perian, VLC, and Flip4Mac installed. Neither computers have Quicktime 7 installed. All software is up-to-date. I have multiple .avi videos that were created with a Microsoft Video 1 codec. These videos play without problem in Quicktime 10 on the iMAC, but cannot be viewed on the upgraded MacBook Air in QT. I already tried reupgrading the OS on the MacBook. Any suggestions?

    One of the genius at Apple was able to solve the problem. The SL upgrade did not erase some of the old Leopard settings in the library. After the quicktime directory of both the user library and the main library were deleted, the video files played normally.

  • Can i upgrade the ram to 4MB on my first generation mac air, can i upgrade the ram to 4MB on my first generation mac air

    can i upgrade the ram to 4MB on my first generation mac air, can i upgrade the ram to 4MB on my first generation mac air

    No. Max supported is 2 GBs.

  • My ipad 2 wont upgrade from 5.1.1 to ios7. I keep getting the message software is up to date which it is clearly not

    My ipad 2 wont upgrade from 5.1.1 to ios7. I keep getting the message software is up to date which it is clearly not.
    I have followed the how to upgrade info but cannot proceed past software update.
    I had no problems with my iphone 4

    Your iPad doesn't have a camera!!.... Didn't you say your iPad was an iPad 2 ??
    If your iPad is an iPad 2 then it will have a camera (front and back) and will be able to update to iOS 7.
    The first iPad's last update was before iOS 6, and you said yours was saying 5.1.1 was up to date, then it is probably and iPad first gen not an iPad 2.
    So to answer your question.... You can't update to iOS 7 because your iPad is a first gen not an iPad 2.
    I hope this helped!!!! :D

  • When i click check for upgrade it wont upgrade since 1.1.5??how can i fix this ?

    when i click upgrade my ipod touch wont upgrade...its a 1.1.5 and i want to upgrade it...how can i fix this ?

    Purchasing iOS 3.1 Software Update for iPod touch (1st generation)

  • Apps wont upgrade keep getting old email address

    apps wont upgrade old email keeps appearing signed out then back in didnt work

    Content acquired via iTunes is permanently tied to the Apple ID it was acquired with.  Enter the correct credentials to update the apps in question.

  • Is the IOS5 upgrade for iphone 3G because mine says it is up to date and wont upgrade to IOS 5

    is the IOS5 upgrade for iphone 3G because mine says it is up to date and wont upgrade to IOS 5

    This is all true.
    The iphone 3G can only be updated to 4.2.1.  It will not support any version higher than that.

Maybe you are looking for