Air-lap-1131-ag-e-k9 convert to autonomous not working
Hi,
i have a air-lap01131-ag-e-k9 that was originally in lightweight mode and configured with a controller, but i am in the process of wanting to convert to autonomous mode, i am having issues with connectivity to the AP from my laptop.
i have followed numerous guides on this forum, i have successfully
downloaded correct firmware
renamed the firmware to .default
placed this in root of tftp server folder
connected laptop via console to view output
connected laptop via Ethernet to Ethernet port of AP
changed static ip on laptop to 10.0.0.2 set subnet mask to 255.255.255.0, default gateway to 10.0.0.1
held reset button on AP when applying power and waiting for radio light to flash red
AP gets a IP address then of 10.0.0.1
But even though both laptop and AP are in the same subnet, i am unable to ping the AP from my laptop and it doesn't start the tftp process
I have disabled firewall etc, and tried with both crossover and straight through cable, it seems there is something missing at this last stage, i even tried on a second laptop but that would not ping either, am i missing something.
i acquired the AP for training purposes to help with studies and so far i have learnt a lot of troubleshooting but i would really love to get past this, any help would be really appreciated.
Kind regards
Sam
Xmodem file system is available.
flashfs[0]: 29 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 7215616
flashfs[0]: Bytes available: 8783360
flashfs[0]: flashfs fsck took 31 seconds.
Base ethernet MAC Address: 00:1e:f7:ed:b5:46
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
button pressed for 20 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1130-k9w7-tar.default
examining image...
%Error opening (no such file or directory)Loading "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"...#########################################################################################################################################################################
File "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
Image text-base: 0x00003000, data-base: 0x0035E440
Initializing flashfs...
flashfs[1]: 29 files, 9 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 7215616
flashfs[1]: Bytes available: 8783360
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-LAP1131AG-E-K9 (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ1222Q27A
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1E:F7:ED:B5:46
Part Number : 73-8962-12
PCA Assembly Number : 800-24818-11
PCA Revision Number : B0
PCB Serial Number : FOC122106TU
Top Assembly Part Number : 800-29144-02
Top Assembly Serial Number : FCZ1222Q27A
Top Revision Number : A0
Product/Model Number : AIR-LAP1131AG-E-K9
Press RETURN to get started!
*Mar 1 00:00:06.280: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 00:00:06.289: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
*Mar 1 00:00:07.238: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:08.238: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:09.642: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:00:25.297: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:36.237: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
Similar Messages
-
I am trying to connect my MacBook Pro to my TV with a mini display port to HDMI converter. Its not working. Any suggestions?
Depends on your model TV. Read your TV user manual. The newer models have "how to hookup" instructions for computer & games.
You can also do a forum search as well as a Google search. -
In-built camera in Macbook Air with OS X version 10.9.1 is not working
In-built camera in Macbook Air with OS X version 10.9.1 is not working. Can anyone help?
Hope info from this article is helpful.
http://support.apple.com/kb/HT2090
Reset SMC. http://support.apple.com/kb/HT3964
Choose the method for:
"Resetting SMC on portables with a battery you should not remove on your own".
If this does not help, contact Apple.
Best. -
MacBook Air osx 10.7.5 ... volume not working on some internet videos or songs, on items used before (3wks ago) it has always worked
Is there a volume icon at the bottom of the video window when you move the mouse pointer over to bottom
of the window? -
I have downloaded PDF Converter and its not working properly
the pdf I am attempting to convert to edit is not working. I have converted it to all that is available and the lines are off in someplaces and some data is in the wrong place when I try to Move it I can't or it makes it worse. what can I do?
As Pat said, which PDF Convertor are you reffereing to here? Which adobe application are you using for the same? What's the operating system that you are using?
-
Air 2.7 and MacOs Lion: iPhone packager does not work
hi. After upgrading from Snow Leopard to Lion the iPhone packager does not work. It throws an error concerning the Application Version Number. Is this a Know bug? Is there a work- around? Thanks. Michael.
Yeah sorry, the start of my descriptor looks like this:
<?xml version="1.0" encoding="utf-8" standalone="yes"?>
<application xmlns="http://ns.adobe.com/air/application/2.7">
<id></id>
<versionNumber></versionNumber>
<filename>d</filename>
<description/>
<name></name>
When I go to compile the app the compiler inserts that line into my descriptor at the very bottom (just before the application tag closes). It's weird, I tried setting the <application xmlns="http://ns.adobe.com/air/application/2.7"> back to 2.6 and it works and seems to compile in 2.7 (as I noticed the timer bug).
Anyway, I only tried 2.7 because I heard the GPU fullscreen bug had been fixed, but given that the timer issue still remains I'll go back to 2.6 for the time being.
Thanks -
Cisco AIR-LAP 1131 reboot in loop
Hi Everyone
I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
Exception (1100)! Data TLB Miss
SRR0 = 0x005A9048 SRR1 = 0x00029230 SRR2 = 0x0028007C SRR3 = 0x00021230
ESR = 0x00000000 DEAR = 0x025BFB94 TSR = 0x84000000 DBSR = 0x00000000
CPU Register Context:
Vector = 0x00001100 PC = 0x005A9048 MSR = 0x00029230 CR = 0x53000035
LR = 0x0048A8A0 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00CD9790 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000C3
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00CDB580 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x0184C8AA R17 = 0x0184C71B R18 = 0x00CDB760 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Stack trace:
PC = 0x005A9048, SP = 0x00CD9790
Frame 00: SP = 0x00CD97D0 PC = 0x0048A6A8
Frame 01: SP = 0x00CDB728 PC = 0x004361FC
Frame 02: SP = 0x00CDB740 PC = 0x0042E078
Frame 03: SP = 0x00CDB758 PC = 0x0044880C
Frame 04: SP = 0x00CDB798 PC = 0x0042A280
Frame 05: SP = 0x00CDB7C0 PC = 0x0042AA68
Frame 06: SP = 0x00000000 PC = 0x0018A990
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
St-John-AP1 uptime is 1 minute,
cisco AIR-LAP1131G-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
And this is all it does, and keep loading the image. I already know the recovery procedure to reset it, but i wanted to know how i can put these AP in HREAP without having these issues. In the setup we need, we cannot have those AP be in local mode.
Thanks for any help and consideration .
RegardsHi Scott
Thanks for replying
here is the full output between loops :
Press RETURN to get started!
*Mar 1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.281: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
*Mar 1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
*Mar 1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
Translating "CISCO-LWAPP-CONTROLLER.aimfire.net"...domain server (10.1.10.100) [OK]
*Mar 1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Mar 1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Mar 1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed sta
15:52:12 UTC Fri Mar 1 2013: Unexpected exception to CPUvector 1100, PC = 0x5A9048 , LR = 0x48A8A0
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
CPU Register Context:
MSR = 0x00029230 CR = 0x53000035 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00D1EC18 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000CA
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00D20A08 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x01851A6A R17 = 0x018518DB R18 = 0x00D20BE8 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Writing crashinfo to flash:/crashinfo_20130301-155213
=== Flushing messages (15:52:20 UTC Fri Mar 1 2013) ===
Buffered messages:
*Mar 1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.281: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
*Mar 1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
*Mar 1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
*Mar 1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Mar 1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Mar 1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed state to UP
*Mar 1 15:52:11.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
Queued messages:
*Mar 1 15:52:23.534: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Mar 1 15:52:11.414: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Nested exception_rom_monitor call (2 times)
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
Exception (1100)! Data TLB Miss
SRR0 = 0x005A9048 SRR1 = 0x00029230 SRR2 = 0x0028007C SRR3 = 0x00021230
ESR = 0x00000000 DEAR = 0x025BFB94 TSR = 0x84000000 DBSR = 0x00000000
CPU Register Context:
Vector = 0x00001100 PC = 0x005A9048 MSR = 0x00029230 CR = 0x53000035
LR = 0x0048A8A0 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00D1EC18 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000CA
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00D20A08 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x01851A6A R17 = 0x018518DB R18 = 0x00D20BE8 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Stack trace:
PC = 0x005A9048, SP = 0x00D1EC18
Frame 00: SP = 0x00D1EC58 PC = 0x0048A6A8
Frame 01: SP = 0x00D20BB0 PC = 0x004361FC
Frame 02: SP = 0x00D20BC8 PC = 0x0042E078
Frame 03: SP = 0x00D20BE0 PC = 0x0044880C
Frame 04: SP = 0x00D20C20 PC = 0x0042A280
Frame 05: SP = 0x00D20C48 PC = 0x0042AA68
Frame 06: SP = 0x00000000 PC = 0x0018A990
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
St-John-AP1 uptime is 1 minute, 7 seconds
cisco AIR-LAP1131G-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
flashfs[0]: 40 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 15129600
flashfs[0]: Bytes available: 869376
flashfs[0]: flashfs fsck took 41 seconds.
Base ethernet MAC Address: d8:67:d9:ba:9f:2e
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2"...###############################################
File "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
Image text-base: 0x00003000, data-base: 0x005AEE20
Initializing flashfs...
flashfs[1]: 40 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 15129600
flashfs[1]: Bytes available: 869376
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Radio 1 A506 7100 E8000000 A0000000 80000000 3
Radio 0 0 0 0 0 0 2
cisco AIR-LAP1131G-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from unknown reload cause - reason ptr 0xF, PC 0x5A9048, address 0x0
LWAPP image version 4.1.192.35
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: D8:67:D9:BA:9F:2E
Part Number : 73-13304-02
PCA Assembly Number : 800-36409-01
PCA Revision Number : B0
PCB Serial Number : FOC16304BZJ
Top Assembly Part Number : 800-29582-03
Top Assembly Serial Number : FTX1632N00D
Top Revision Number : A0
Product/Model Number : AIR-LAP1131G-A-K9
Press RETURN to get started!
Also , the switchport is a trunk port, i can definitely try it an access port . -
Adobe Bridge CS4 - "convert to DNG" not working?
Hi
I am downloading a bunch of raw .CR2 files taken with a Canon 5D mark iii, and trying to convert them to DNG using Bridge, so that I can open them up in Camera Raw (which won't read the original CR2 files as you need CS5.5 or later). I have selected the "convert to DNG" option but the conversion doesn't seem to work, it's just copying the CR2 files over, Any idea why?
thanksI have selected the "convert to DNG" option but the conversion doesn't seem to work, it's just copying the CR2 files over, Any idea why?
It seems you are using Photodownloader that comes with the CS version you are using currently. This Photodownloader is linked to the Raw converter of the version it is part of. So if it does not show the CR2 files as images it also won't convert to DNG
For this you need to download the latest and Free Adobe DNG converter.
Check this page, there is also an option to download the converter for either Mac or Windows -
Does anyone know how to get the Adobe Photoshop Lightroom 3 to update so you can use it? I can't process raw files with my new Canon SD Mark 3.
It looks like they stopped doing updates.
Next I tried the DNG converter but it was useless. It could not find any of my photos.
SOS - I needed to complete a job with this last night and their site won't help and they finally respond by saying we will get back to you in a few days.That camera requires at least Lightroom 4.1. There is no update for Lightroom 3 that will support the files from that camera. I'm guessing that you're having the typical problem that new users at the DNG converter encounter. The converter prompts for the *FOLDER*. If you open that folder then the DNG converter will tell you there are no files to convert. Just choose the folder. I know, it's really stupid prompt and method. But it is what it is.
-
I've got a Macbook Air Mid 2013 with Yosemite 10.10.1 and can't get the 2 devices to stay paired via Bluetooth.
The 2 devices try to pair and after 2-3 sec's they disconnect.
Both are on the same wireless network and handoff is toggled on.
Does anyone have any ideas on how to get this handoff working?Have you worked through the knowledge base tips in:Get help using Continuity with iOS 8 and OS X Yosemite - Apple Support
-
Edit Edit Colors Convert to Grayscale Not working
In Ai CS6 when I select all and try to convert to GS nothing seems to happen. I still have a RGB/preview and if I go back to the edit colors menu, convert to cmyk is still grayed out, suggesting that the art is still 4c. Thanks for your help!
Jonjaal,
Illy refuses to convert RGB to CMYK and CMYK to RGB, therefore the opposite is greyed out.
So you are in RGB mode.
Is there any RGB vector artwork that is non grayscale?
If there is, it may be time for the list.
The following is a general list of things you may try when the issue is not in a specific file, and when it is not caused by issues with opening a file from external media. You may have tried/done some of them already; 1) and 2) are the easy ones for temporary strangenesses, and 3) and 4) are specifically aimed at possibly corrupt preferences); 5) is a list in itself, and 6) is the last resort.
If possible/applicable, you should save current artwork first, of course.
1) Close down Illy and open again;
2) Restart the computer (you may do that up to at least 5 times);
3) Close down Illy and press Ctrl+Alt+Shift/Cmd+Option+Shift during startup (easy but irreversible);
4) Move the folder (follow the link with that name) with Illy closed (more tedious but also more thorough and reversible), for CS3 - CC you may find the folder here:
https://helpx.adobe.com/illustrator/kb/preference-file-location-illustrator.html
5) Look through and try out the relevant among the Other options (follow the link with that name, Item 7) is a list of usual suspects among other applications that may disturb and confuse Illy, Item 15) applies to CC, CS6, and maybe CS5);
Even more seriously, you may:
6) Uninstall (ticking the box to delete the preferences), run the Cleaner Tool (if you have CS3/CS4/CS5/CS6/CC), and reinstall.
http://www.adobe.com/support/contact/cscleanertool.html -
Convert to word not working - answers to form questions missing
Hi there
I have a form that was filled by a client that is now in pdf format. I am trying to convert it into a word file.
All of the questions and the blank boxes for the answers are coming across, but the answers to the questions within the boxes are missing.
Help would be appreciated please.
RebeccaWell, they are right pretty much. PDF forms are not for conversion into Word. The export tools are about getting the data out NOT the look of the form.
Generally, converting forms of any kind (filled or not) from PDF to Word is a non-starter. The layout will change too much OR it will be utterly uneditable in Word, rendering all practical reasons for converting to Word useless.
Conversion to Word from PDF is a way to get back the text and hint of the layout ready for re-creation. -
Is anyone else having the same problem with iTunes 12 not being able to convert mp3's to AAC without cutting all the songs down to the same time length as the 1st song?
Doesn't seem a widespread issue. One post from 2013 and one more recent one but iTunes for Windows. I presume you want to know more than simply if others have observed this behavior in the past 10+ years of iTunes. Your answer seems to be, "Yes, but not enough that anybody has a solution for it".
If you want to know why I suggest you start doing a general web search or a structured research project on your own if it is doing this with all mp3 files, only those of a certain bitrate or source, etc. Make sure you also document your computer configuration, all software. Then start deleting things and see if they are in conflict. Document all steps carefully and send reports to the software engineers for the components involved.
Me, I would just use a third party converter such as Max or XLD and get on with it. -
Convert to Keyframes not working????
Hello
I have a layer and in that layer I have two pieces of media (a PNG and some text). There is a throw command attached to the whole layer with a "Ramp to final value" set. I want the movement to "ease out" but when I select everything in the layer and then say convert to keyframe ie cmd-K nothing happens, I get the "this could take some time" warning, but there are no Keyframe????
What am I doing wrong? Any ideas. First time I'm using convert to keyframes, so don't know if I'm doing the right thing.
Thanks in advance.2 things - since the behavior is attached to the layer, you need to select the layer to do convert to keyframes - if you select the objects inside the layer nothing will happen since no behaviors are applied to them directly.
Second, the Throw behavior needs to have "Affect Objects" turned off, otherwise it is applying the animation to the objects inside the layer while still applied to the layer itself.
Basically, convert to keyframes needs to work on something that has behaviors on it directly, and also is affected directly by those behaviors. -
IPad air safari not working in iOS 8.1
I have an iPhone 5, 5S and ipad air all on version 8.1. Safari is not working on any of them. It tries to load, the blank safari screen comes up, then it crashes and goes back to home screen. I have to use google chrome to access the internet. I tried restoring my one phone to factory, installed the backup, reset the safari data, reset network settings and still no help. Can anyone tell me how the **** to delete safari and re-install it? I don't know what else to do about this issue.
Here's one URL copied & paste properly, hope this helps!
Thank you for looking into this issue...
http://www.geocaching.com/error/error.aspx?aspxerrorpath=/seek/cache_details.asp x
Maybe you are looking for
-
CREATE OR REPLACE procedure pt_load_withouttran1(tabname in varchar2 , tabname2 in varchar2, condition in varchar2) is --tabname varchar2(100) := 'atlanta_operator'; -- tabname2 varchar2(100) := 'pt_atlanta_operator'; sql_text varchar2(2000) := 'decl
-
Join 2 tables which are not related with any primary-foriegn key constraint
Hello, How to join 2 tables which are not related with any primary key foreign key constraint. Ex.Consider Table A has 5 columns->A_ID,A_Name,A_Address,A_City,A_Pin(Total 10 rows) Table B has 5 columns->B_ID,B_Name,B_Adress,B_City,B_City(Total 30 row
-
Dynamic selective deletion of last working day in cube
Hi experts I have studied this document: http://scn.sap.com/community/data-warehousing/netweaver-bw/blog/2013/08/06/selective-deletion-in-process-chain We need to delete each month at the 6th working day all records of the last working day of the pre
-
Error when texting on iPhone 4 "this message has attachments which were lost" (there are no attachments) friend has blackberry - help!!
-
4gb nano. cannot fit more than 3.8gb to it
HELP. I cannot sync more than about 3.5gb to my 4gb ipod nano, there is a warning screen that comes up when I try to add more... what can i do?