AIR-LAP1131G and AIR-LAP1242G Latest WLAN Controller Compatibility

Would like to ask if below APs are compatible with WLC 5508 with current version of 7.0.240.0:
Cisco AIR-LAP1131G-A-K9
Cisco AIR-LAP1242G-A-K9

Yes they are supported in that version.
You want to check the release notes for AP support.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn7_0_240_0.html#wp784295
HTH,
Steve

Similar Messages

WLAN Controller Compatibility

Hi all,
i want to know if CISCO Wlan Controller can support third party Access Point (SENAO ENgenious EAP3660).
thanks in advance

No, only Cisco AP's are supported.

WLAN Controller can configure as ACTIVE-ACTIVE

Customer is looking for two numbers WLAN Controller (AIR-AP1242AG-E-K9). And they want to configure as ACTIVE-ACTIVE. I would like to know whether it can be configuring as ACTIVE-ACTIVE.
And Is really require WLAN Controller for AIR-AP1242AG-E-K9 access point ? or it can be configure without WLAN controller ?
Please revert me ASAP
Regards,
Manoj

Hi Manoj,
Although WLC Controllers can be configured in an Active-Active type redundancy, you don't need the WLC for small deployments. The AIR-AP1242AG-E-K9 access point can be setup in Autonomous or Stand-alone mode as well :)
Cisco IOS Software Configuration Guide for Cisco Aironet Access Points 12.3(7)JA
http://www.cisco.com/en/US/docs/wireless/access_point/12.3_7_JA/configuration/guide/i1237sc.html
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
http://www.cisco.com/en/US/docs/wireless/access_point/1200/installation/guide/1200-TD-Book-Wrapper.html
Hope this helps!
Rob

AIR-LAP1310G-E-K9 acces point not joining to 5508 wlan controller

Hi,
I have Cisco AIR-LAP1310G-E-K9 access point and 5508 wlan controller with version 7.0.220 and it is joining to the WLAN controller. I have enabled dhcp in the lan controller and i dont have external dns server. How to fix this issue? Can this LAN controller version will support this access point?
My Lan Controller Management IP Address is 10.10.10.5
Please find the below configuration of 1300 access point.
AP001d.4513.dd68#reload
Proceed with reload? [confirm]
%SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.
%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.
flashfs[0]: 4 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 2052608
flashfs[0]: Bytes available: 5688832
flashfs[0]: flashfs fsck took 14 seconds.
Base ethernet MAC Address: 00:1d:45:13:dd:68
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Unable to get our ip address: no "IP_ADDR" variable set
The system has been encountered and error initializing
tftp file system. The system is ignoring the error and
continuing boot. If you interrupt the system boot process,
the following commands will set IP_ADDR, DEFAULT_ROUTER
and NETMASK environment variables, initializing tftp file
system, and finish loading the operating system software:
    set IP_ADDR
    set DEFAULT_ROUTER
    set NETMASK
    tftp_init
    boot
Loading "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx"...############################################################################################################################################################################################
File "flash:/c1310-rcvk9w8-mx/c1310-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.4(10b)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Wed 19-Mar-08 19:09 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x003BE9E0
Initializing flashfs...
flashfs[1]: 4 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 7741440
flashfs[1]: Bytes used: 2052608
flashfs[1]: Bytes available: 5688832
flashfs[1]: flashfs fsck took 2 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1310G-E-K9R   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FHK1133E002
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from reload
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1D:45:13:DD:68
Part Number                          : 73-8960-09
PCA Assembly Number                  : 800-24963-06
PCA Revision Number                  : A0
PCB Serial Number                    : FOC113000V7
Top Assembly Part Number             : 800-28479-05
Top Assembly Serial Number           : FHK1133E002
Top Revision Number                  : B0
Product/Model Number                 : AIR-LAP1310G-E-K9R
The name for the keys will be: ap.cisco.com
% The key modulus size is 1024 bits
% Generating 1024 bit RSA keys, keys will be non-exportable...[OK]
ip ssh version 2
    ^
% Invalid input detected at '^' marker.
transport input ssh
                 ^
% Invalid input detected at '^' marker.
aaa new-model
^
% Invalid input detected at '^' marker.
aaa authentication login default enable local none
^
% Invalid input detected at '^' marker.
o
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:05.442: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.473: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:07.817: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1310 Software (C1310-RCVK9W8-M), Version 12.4(10b)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Wed 19-Mar-08 19:09 by prod_rel_team
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
transport input ssh
                 ^
% Invalid input detected at '^' marker.
*Mar 1 00:00:33.860: %LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER
*Mar 1 00:00:33.860: %LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLLER
*Mar 1 00:00:33.861: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
logging origin-id string AP:001d.4513.dd68
         ^
% Invalid input detected at '^' marker.
logging 255.255.255.255
        ^
% Invalid input detected at '^' marker.
logging trap 3
        ^
% Invalid input detected at '^' marker.
*Mar 1 00:00:37.440: Logging LWAPP message to 255.255.255.255.
AP001d.4513.dd68>
%LWAPP-3-CLIENTEVENTLOG: Forcing AP to obtain IP address using DHCP
%DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.10.46, mask 255.255.255.0, hostname AP001d.4513.dd68
Translating "CISCO-LWAPP-CONTROLLER.CISCO-LWAPP-CONTROLLER.mydomain.com"...domain server (10.10.10.5)
%LWAPP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.CISCO-LWAPP-CONTROLLER.mydomain.com
%LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLLER.CISCO-LWAPP-CONTROLLER.mydomain.com
AP001d.4513.dd68>

Your debug is very telling ..
AP001d.4513.dd68>
%LWAPP-3-CLIENTEVENTLOG: Forcing AP to obtain IP address using DHCP
%DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.10.10.46, mask 255.255.255.0, hostname AP001d.4513.dd68
Translating "CISCO-LWAPP-CONTROLLER.CISCO-LWAPP-CONTROLLER.mydomain.com"...domain server (10.10.10.5)
%LWAPP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.CISCO-LWAPP-CONTROLLER.mydomain.com
%LWAPP-3-CLIENTERRORLOG: DNS Name Lookup: could not resolve CISCO-LWAPP-CONTROLLER.CISCO-LWAPP-CONTROLLER.mydomain.com
AP001d.4513.dd68>
What are you using to tell the AP where the contoller lives ? Since you are consoled into the ap you can use the -> capwap ap controller ip address
This will point the ap to your controller
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
‎"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."

I am continually getting error -69 when syncing iPad Air with latest iOS and iTunes versions. Any suggestions?

I am continually getting error -69 when syncing iPad Air with latest iOS and iTunes versions. Any suggestions?

Try Googling "sync without iTunes".
There are free alternatives and there are not so free alternatives.
Btw, to check if AVG is causing the problem, you should uninstall AVG and not just "turn it off".
Also, can you describe how you go about uninstalling a program? For example, how did you "delete" iTunes?

AIR-LAP1242G-E-K9 do not work with AIR-CT5508-K9 while AIR-LAP1142N-E-K9 do

Hello,
we do have a site where we need to deploy AIR-LAP1142N-E-K9 and AIR-LAP1242G-E-K9 APs. We have two AIR-CT5508-K9 controllers with SW version                  6.0.188.0.
AIR-LAP1142N-E-K9s work okay, as expected, we do not have any problems with them.
However AIR-LAP1242G-E-K9s do not, there is a problem with establishing CAPWAP tunnel with the controller.The AP is seen on the controller for a while, with 0 time up-time, cannot change any settings on the AP via controller, and after a while it disapears from the controller, apears again and this repeats.
The APs and controllers are connected to the LAN campus.
Controllers via two 1G links configured as Etherchannel to WS-C6506-E VSS switch with s72033-ipservicesk9_wan-vz.122-33.SXI1.bin on it.
APs to WS-C3750G-48PS with c3750-ipbasek9-mz.122-50.SE2.bin on it. 3750 is connected to the C6505 via two 1G links configured as Etherchannel.
Below I copied the log I captured on 1242 and the controller. Highlighted ones are the ones which I think might bring a clue.
I performed some troubleshooting steps.
- As we have some other controllers available over WAN, I tested the 1242 AP with 2100, 4400 and also with the same model AIR-CT5508-K9 with SW version                  6.0.188.0 over WAN and this worked always okay.
- I wanted to be sure that I eliminate any kind of out of sequence packet issue, so I brought down all redundancy L2 links so that the L2 path from the AP to the controller was only through one leg links.
- I also brought the second controller down to eliminate potential issue with having two of them up.
- The AP gets its IP from DHCP configured on the C6506 switch, I am always able to ssh to AP, so the IP connectivity does not seem to be an issue.
- I have more 1242s, all behave in the same way. I also connected them to some other 3750 switches we have in the campus, always the same.
- As this seems to be maybe a kind of ssl issue, I tried to play with controller settings, like enabling Accept... options under Security/AP Policy,but this did not help.
- I also tried to reboot the controller, no improvement.
- The APs came from the factory, so in the beginning everything was factory default in them. They were always able to download the image from the controller in the very initial phase. I still do have some of them untouched, so I can perform any troubleshooting steps with the fresh one.
I can reproduce this, can also send debugging logs if needed.
Any idea on what could be wrong is highly appreciated.
Thank you.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
This Discussion has been converted into document:- https://supportforums.cisco.com/docs/DOC-23054
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
AIR-LAP1242G-E-K9 10.0.13.28 log
*Mar 1 00:00:05.922: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.536: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot1 1Radio 0
*Mar 1 00:00:07.672: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 304 messages)
*Mar 1 00:00:09.809: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:09.874: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:42 by prod_rel_team
*Mar 1 00:00:09.874: %SNMP-5-COLDSTART: SNMP agent on host wuen4028 is undergoing a cold start
*Mar 1 00:00:09.964: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:09.967: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:10.191: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:10.191: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:10.430: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.818: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:11.212: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:18.315: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.0.13.28, mask 2 55.255.255.0, hostname wuen4028
*Mar 1 00:00:28.988: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:00:31.456: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:31.495: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:32.457: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:32.457: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
*Mar 1 00:00:38.810: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:00:47.811: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
*Mar 1 00:00:56.812: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-LWAPP-CONTROLLER
*Mar 1 00:01:07.815: %CAPWAP-3-ERRORLOG: Selected MWAR 'wuen4001'(index 0).
*Mar 1 00:01:07.815: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Feb 11 07:52:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.13.5 peer_port: 5246
*Feb 11 07:52:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Feb 11 07:52:25.441: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.0.13.5 peer_port: 5246
*Feb 11 07:52:25.443: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.13.5
*Feb 11 07:52:25.443: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 10.0.13.5
*Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
*Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Feb 11 07:52:25.445: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.0.13.5
*Feb 11 07:52:30.441: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.13.5
*Feb 11 07:52:30.442: %CAPWAP-3-ERRORLOG: Unencrypted non-discovery CAPWAP Control Message from 10.0.13.5
*Feb 11 07:52:30.443: %CAPWAP-3-ERRORLOG: Invalid AC Message Type 4.
*Feb 11 07:52:30.443: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Feb 11 07:52:30.443: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 10.0.13.5
*Feb 11 07:52:47.644: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Feb 11 07:53:23.999: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.0.13.5:5246
*Feb 11 07:53:24.000: %CAPWAP-3-ERRORLOG: Selected MWAR 'wuen4001'(index 0).
*Feb 11 07:53:24.000: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Feb 11 07:52:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.13.5 peer_port: 5246
*Feb 11 07:52:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Feb 11 07:52:24.001: %DTLS-5-PEER_DISCONNECT: Peer 10.0.13.5 has closed connection.
*Feb 11 07:52:24.001: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.0.13.5:5246
*Feb 11 07:52:24.002: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
*Feb 11 07:52:24.123: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is not established.
wuen4028#
AIR-CT5508-K9 10.0.13.5 log
*Feb 11 09:00:54.824: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2171 Failed to c
omplete DTLS handshake with peer 10.0.13.28
                                           *Feb 11 08:59:53.798: %DOT1X-3-MAX_EA
P_RETRIES: 1x_auth_pae.c:2862 Max EAP identity request retries (3) exceeded for
client 00:1f:3b:93:dd:4f
*Feb 11 08:59:51.197: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
ity request retries (3) exceeded for client 00:c0:a8:e1:b1:71
--More-- or (q)uit
*Feb 11 08:59:21.212: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
rector: Could not find valid channel lists for 802.11bg
*Feb 11 08:58:39.766: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2171 Failed to c
omplete DTLS handshake with peer 10.0.13.28
                                           *Feb 11 08:57:06.131: %RRM-3-RRM_LOGM
SG: rrmChanUtils.c:292 RRM LOG: Airewave Director: Could not find valid channel
lists for 802.11bg
*Feb 11 08:56:24.504: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:2171 Failed to c
omplete DTLS handshake with peer 10.0.13.28
                                           *Feb 11 08:55:09.693: %DOT1X-3-MAX_EA
P_RETRIES: 1x_auth_pae.c:2862 Max EAP identity request retries (3) exceeded for
client 00:1f:3b:93:dd:4f
*Feb 11 08:54:51.040: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
rector: Could not find valid channel lists for 802.11bg
*Feb 11 08:53:56.493: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
sions exceeded for client 00:1f:3b:93:dd:4f
*Feb 11 08:53:34.497: %DTL-3-OSARP_DEL_FAILED: dtl_arp.c:1380 Unable to delete a
n ARP entry for 10.0.13.28 from the operating system. ioctl operation failed
*Feb 11 08:52:35.936: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
rector: Could not find valid channel lists for 802.11bg
*Feb 11 08:52:26.492: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
sions exceeded for client 00:1f:3b:93:dd:4f
*Feb 11 08:50:07.680: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
sions exceeded for client 00:1f:3b:93:e6:57
*Feb 11 08:48:37.458: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
ity request retries (3) exceeded for client 00:1f:3b:93:e6:57
*Feb 11 08:47:37.438: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmis
sions exceeded for client 00:1f:3b:93:e6:57
*Feb 11 08:47:34.438: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
ity request retries (3) exceeded for client 00:16:44:1d:0f:53
*Feb 11 08:46:32.422: %DOT1X-3-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:407 Max EAPOL-ke
y M3 retransmissions exceeded for client 00:16:44:1d:0f:53
*Feb 11 08:46:06.790: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
ity request retries (3) exceeded for client 00:1f:3b:95:61:bd
*Feb 11 08:46:06.789: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 Authentication abor
ted for client 00:1f:3b:95:61:bd
*Feb 11 08:46:06.210: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
ity request retries (3) exceeded for client 00:1f:3b:93:e6:57
*Feb 11 08:45:34.304: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2862 Max EAP ident
ity request retries (3) exceeded for client 00:1f:3b:95:61:bd
*Feb 11 08:45:34.303: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 Authentication abor
ted for client 00:1f:3b:95:61:bd
*Feb 11 08:45:01.298: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:292 RRM LOG: Airewave Di
rector: Could not find valid channel lists for 802.11bg
*Feb 11 08:44:38.076: %SIM-3-PORT_UP: sim.c:9547 Physical port 2 is up!.
*Feb 11 08:44:38.037: %SIM-3-PORT_UP: sim.c:9547 Physical port 1 is up!.
--More-- or (q)uit
*Feb 11 08:44:38.009: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'cliWebInitParms.cfg'
*Feb 11 08:44:37.980: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'rrcEngineInitParms.cfg'
*Feb 11 08:44:37.980: %CNFGR-3-INV_COMP_ID: cnfgr.c:2105 Invalid Component Id :
Unrecognized (81) in cfgConfiguratorInit.
*Feb 11 08:44:37.928: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'rfidInitParms.cfg'
*Feb 11 08:44:37.915: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'dhcpParms.cfg'
*Feb 11 08:44:37.903: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'bcastInitParms.cfg'
*Feb 11 08:44:37.834: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'rrmInitParms.cfg'
*Feb 11 08:44:27.331: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'apfInitParms.cfg'
*Feb 11 08:44:27.226: %MM-3-MEMBER_ADD_FAILED: mm_dir.c:903 Could not add Mobili
ty Member. Reason: IP already assigned, Member-Count:1,MAC: 00:00:00:00:00:00, I
P: 0.0.0.0
*Feb 11 08:44:27.023: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'mmInitParms.cfg'
*Feb 11 08:44:27.013: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'aaaapiInitParms.cfg'
*Feb 11 08:44:27.011: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'pemInitParms.cfg'
*Feb 11 08:44:26.898: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'dot1xInitParms.cfg'
*Feb 11 08:44:26.868: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'capwapInitParms.cfg'
*Feb 11 08:44:26.718: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'spamInitParms.cfg'
*Feb 11 08:44:25.650: %SSHPM-3-FREAD_FAILED: sshpmlscscep.c:1395 Error reading f
ile /mnt/application/lscca_pem.crt
*Feb 11 08:44:06.435: %SYSTEM-3-FILE_READ_FAIL: nvstore.c:422 Failed to read con
figuration file 'sshpmInitParms.cfg'

Thanks for such quick response and suggestions.
Yes, I seem not to to be 100% perfect as for the list of troubleshooting steps I took.
I had already tried the two commands you mentioned. I tried again, this time with some other 1242, but these do not help.
Yes, I was already thinking that this could be in theory a licensing issue. The controller is bougth with 25 licenses.
In the beginnign I had one 1142 on it and tried to enable 1242s which did not work. Now I have five 1142s on it, as this worked okay, I guess it could not be a licensing issue.
I think that I can see in the log files that the machines communicate to each other, L2 or L3 paths seem to be working okay. I forgot to mention that I am using option 43 on the DHCP server, so the AP clearly finds its way to the controller. What's more both APs and the controllers are in the same VLAN, so they are in the same broadcast domain.
Below is sho ver from the AP. The AP seems to have Certificate type - manufacture installed, so I guess there should not be a problem with the certificate, especially knowing that the AP works with other controllers over WAN.
My guess these messages seen on AP especially "Invalid event 38 & state 3 combination" might tell us what's wrong.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
*Feb 11 07:52:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Feb 11 07:52:24.001: %DTLS-5-PEER_DISCONNECT: Peer 10.0.13.5 has closed connection.
*Feb 11 07:52:24.001: %DTLS-5-SEND_ALERT: Send WARNING : Close notify Alert to 10.0.13.5:5246
*Feb 11 07:52:24.002: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 3 combination.
*Feb 11 07:52:24.123: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is not established.
Cisco IOS Software, C1240 Software (C1240-K9W8-M), Version 12.4(21a)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 02-Nov-09 18:42 by prod_rel_team
ROM: Bootstrap program is C1240 boot loader
BOOTLDR: C1240 Boot Loader (C1240-BOOT-M) Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
AP9caf.ca00.1c78 uptime is 17 minutes
System returned to ROM by power-on
System image file is "flash:/c1240-k9w8-mx.124-21a.JA2/c1240-k9w8-mx.124-21a.JA2"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1242G-E-K9    (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ135082GH
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 6.0.188.0
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 9C:AF:CA:00:1C:78
Part Number                          : 73-11479-01
PCA Assembly Number                  : 800-30493-01
PCA Revision Number                  : A0
PCB Serial Number                    : FOC13484GYY
Top Assembly Part Number             : 800-29589-03
Top Assembly Serial Number           : FCZ135082GH
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1242G-E-K9
Configuration register is 0xF
AP9caf.ca00.1c78#

WLan controller 2112 and LAP1042n Access Point issue

Hello,
I recently purchased a 2112 Wlan controller an a number of LAP1042n Ap's. The AP's will not associate to the controller and the message I receive in the console of the AP is that the firmware AIR-WLC2100-K9-6-0-199-4.aes does not support this model? Can someone please verify this is the case?
Will firmware AIR-WLC2100-K9-7-0-98-0.aes overcome this issue?
Thanks in advance
David

YEs, 7.0 does suppoert it...
CHECK THE RELEASE NOTES... for further details...
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7.0.html

AIR-LAP1242G

Hi Everbody,
Cisco 8500 controller's (software 7.4.100.0) datasheet clearly states Cisco AIR-LAP1242G series access point can join cisco 8500 controller. I am using Cisco AIR-LAP1242G software version (C1240-K9W8-M, 12.3(7)JA1, RELEASE SOFTWARE (fc1)) and IOS (c1240-k9w8-mx.ap_jmr3_esc.201204191421/c1240-k9w8-mx.ap_). I tried both console and web interface but Ap did not connect the Cisco 8500 controller.
Is anyone have an idea about this problem
Regards

We are normally using AIR-LAP1242G series Ap with Wism controller. AIR-LAP1242G APs connect to Wism Controller using DHCP option 43 and its also capwap compatible.
"3) Do a capwap events enabled while the ap joins - do you see anything ? If so post" I do not understand this one
We are also using AIR-LAP1131AG-E-K9 with Wism controller. When I send AIR-LAP1131AG-E-K9 series Ap to 8500 controller, it connects and works fine. But when I send to AIR-LAP1242G series AP, it do not connect to 8500 controller.

WLAN Controller 5508 - Latest IOS (april/2013)

Dears,
Can somebody confirm please what is the latest IOS version for the Wlan Controller 5508 ?
Actually I am using
Software Version
7.3.102.0
I see the folliwing at Cisco website
Latest Releases
7.2.115.1(ED)7.3.112.0(ED)
7.0.240.0(ED)
7.4.100.0(ED)
Version 7.2.115 seems to be the latest one (release date 19-APR-2013)... then I see 7.3.112.0 w/ release date 30-JAN-2013...
I thought the IOS 7.4.100 would be the latest one but that release date is 17-DEC-2012
Thats very wierd coz my controller uses a 7.3.102.0.....
Can someone help me ?
What IOS is really the latest one ?
What should be the best one for me ?
Software Version
7.3.102.0
Field Recovery Image Version
System Name
XXX-XXXX-XXX
Thanks in advance!!!

Lets make it simple. There are different trains. 7.0 is one, 7.2 is another, 7.3 is another and 7.4 is another. So if your on 7.2.x, the latest for that version is the .x. Each one listed above is different as far as features so you need to look at the latest for train that your on.
Sent from Cisco Technical Support iPhone App

Communication between : AP and WLAN controller

Hi,
The communication between AP and WLAN Controller is ( Data and Control ) UDP.
Source port 1024 and destination port 12222 and 12223. Actually which device listen to which port or both should listen as control and data can be generated from both the devices.
How does the user ( wireless client) traffic is switched - if user traffic is a TCP traffic. It will be sent to WLANC and then WLANC forwards it to respective VLAN or default gateway ( depending upon the destination in the packet ).
Please explain / share the experience.
any link on cisco.com
Thanka in advance
Subodh

"the LWAPP Control and Data messages are encapsulated in UDP packets that are carried over the IP network. The only requirement is established IP connectivity between the access points and the WLC. The LWAPP tunnel uses the access point's IP address and the WLC's AP Manager interface IP address as endpoints. The AP Manager interface is explained in further detail in the
implementation section. On the access point side, both LWAPP Control and Data messages use an ephemeral port that is derived from a hash of the access point MAC address as the UDP port. On the WLC side, LWAPP Data messages always use UDP port 12222. On the WLC side, LWAPP Control messages always use UDP port 12223.
The mechanics and sequencing of Layer 3 LWAPP are similar to Layer 2 LWAPP except that the packets are carried in UDP packets instead of being encapsulated in Ethernet frames."
Taken from "Cisco 440X Series Wireless LAN Controllers Deployment Guide"

WLAN Controller and Location appliance graceful shutdown?

Does anyone know if there is a supported graceful shutdown method/command for the
4400 series WLAN Controller and 2700 Location Appliances?
This weekend our server room will be undergoing maintenance and will experience a total power outage for a 4 hour period. It is our intent to manually bring all equipment down (hopefully in a graceful manner) and then back up once the maintenance is completed. As a result does anyone know if special precaution is needed to shutdown these 2 appliances, or can we simply bring down these devices hard which is the case with most other Cisco equipment?
Thanks in advance

Hi Mark,
Channel 1, 6, and 11 are just about as non-overlapping as 1, 7, and 13. There's an insignificant amount of overlap, so it's just as plausible of a solution, even in Europe. I honestly don't know why you wouldn't use the extra channels to eliminate the minor overlap - every bit helps.
The "channel blanket" or "virtual cell" WLAN design philosophy is rapidly spreading. Cisco maintains that it's a standards violation and I've heard no talk of them purchasing the not-to-be-named company or of them adopting the same design philosophy. I sincerely hope that they do one of the two soon, however, because it's very good design that's difficult for Cisco to compete against.

WLAN Controller at HQ and AP's at Branch offices

I have a WLAN controller at HQ and want to put APs at my branch offices, but connected and managed by my controller at HQ. I know that if the WAN goes down, I will lose wireless, etc.
my question is:
Is there anything I should watch out for with this type of setup? I will have separate vlans' for the wireless and data.. will this matter when it hits the MPLS from the branch back to the HQ WLAN controller? I thought maybe the vlan tagging had to stay consistant between AP and WLAN controller?

Hybrid Remote Edge Access Point (HREAP) is a mode supportede by 1130 and 1240 series AP's. In the upcoming release of version 4.2, HREAP will also have full support for voice roaming as well. With HREAP, wireless users already authenticated will remain connected in the event of a WAN outage. In addition, v4.2 will support local site authentication for HREAP deployments. If you have an ACS server at the remote site, you can even authenticate new users during a WAN outage. I wouldn't recommend anything in the 1000 series AP family. It's already been announced that it's going end of sale. Keep in mind the latency between AP and controller must be less than 100ms.

Wlan controller and branch office AP (vlan config)

Hi,
Our wlan controller is located in HQ office and we have APs in branch office. Is it possible to implement two different SSIDs and they should be in two different vlans? So should we configure the AP trunk?
REAP does not support IEEE 802.1Q VLAN tagging. As such, it does not support multiple VLANs. Traffic from all the service set identifiers (SSID) terminates on the same subnet, but H-REAP supports IEEE 802.1Q VLAN tagging. Traffic from each SSID can be segmented to a unique VLAN.
Thanks

Hello,
As per your query i can suggest you the following solution-
Yes, it possible to implement two different SSIDs and they can be in two different vlans.
For more information please refer to the link-
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00807cc3b8.shtml
Hope this will help you.

WAP4410N Access point and 4404 WLAN Controller.

Hello to all,
I am planning to setup a new WLAN using WAP4410N Wireless N Access Point. Is it possible to manage the AP using 4404 WLAN controller ?
I need to buy arround 42 AP for covering the entire building.
Regards,
Aslam

leolaohoo
Could u please tell me which series can be used with 4404 WLANC ?
Also the AP Should support Bridging or Mesh.

WLAN controller Software Download

Hi There
I purchased a brand new Cisco wlan controller (2500 model) and one access point from a Cisco authorised supplier. Can I register the controller on the
Cisco website to enable access to download software related to this controller? I want to download the latest "AIR-CTVM-K9-8-0-100-0.aes" software
but I am not allowed according to my profile.
So how do I get access to the latest software for my 2500 WLAN controller ?
Regards
Gideon

Can I register the controller on the Cisco website to enable access to download software related to this controller?
Yes and no.
The quick answer is NO. Your authorized Cisco reseller should be able to "attach" the serial number of your WLC to your Service Contract and your Service Contract is attached to your CCO login.
If you go direct to Cisco, it'll take time to get to the bottom of the details plus you need to furnish so many information it's better to get your Cisco reseller to contact them.

AIR-LAP1131G and AIR-LAP1242G Latest WLAN Controller Compatibility

Similar Messages

Maybe you are looking for