Air Port Express not showing up on Airport Utility scan

I recently reset my password on my Airport extreme base station. After I did this my Airport express, which I use to extend the signal, doesn't work. I probably need to reset it's password, too. But now it doesn't show up on the Airport utility when it scans for devices. I've reset the express. I've unplugged it for a while. What else can I do?

Temporarily, connect an ethernet cable from your computer to the AirPort Express (AX) to see if that helps AirPort Utility "see" the AX.
In order for the AX to extend the signal from the Airport Extreme (AEBS), the following must occur:
Wireless Mode set to Extend a Wireless Network
Wireless Network Name must exactly match the name of the network created by the AEBS
Wireless Security must exactly match the wireless security setting on the AEBS
Wireless Password must exactly match the wireless password setting on the AEBS

Similar Messages

Second AirPort Express not showing up in AirPort Utility

I got a second AirPort Express (APE) to extend my wireless in a different direction from the first but I have not been able to get the new one to show up in the AirPort Utility.
Here are some of the things that I have tried based on my research so far:
-Unplugged APE and waited 30 seconds then plugged it back in
-Pressed reset button untill light blinked, this caused the light to stay solid amber for several seconds then it started slowly blinking again
-Plugged in to Time Capsule with cable, this allowed me to configure the second APE but once I disconnected the cable it still would not connect wirelessly
-Disconected the first APE and "forgot" it in the AirPort Utility, still not able to set up 2nd APE
Did I get a bad unit?

Answering my own post ...
I first directly connected the AX to the iMac using the ethernet cable, and was able to configure the AX (not sure that I actually had to do this, as my issue was probably due to poor signal strength - as described later). I then moved the AX back to the living room, and was able to connect again, but soon it was dropped. Determined that the signal was weak. I played with positioning the AX to optimize signal, and now am able to get OK signal (only about 1/3 strength, based on number of bars in "fan" shaped icon in menu bar). Was able to stream iTunes to stereo as well, which is great. Also determined that the 2WIRE system that Airport was trying to set up WAS my neighbor (and not my gateway/router). If you don't see "Apple XXXXX" base station and network listed when you are in Airport Admin Utility or Internet Connect (which I didn't, but since I was using 2WIRE gateway/router, assumed that it was my AX when the 2WIRE appeared in the Airport network connection option), then the AX is not properly set up (weak signal or other problem).
So, with the AX in the living room (front of the house), and the iMac in the sun room (back of the house), I am able to get OK, but not great signal from AX. So far, seems to be sufficient to connect to internet and stream iTunes. I may see if I can reposition the AX on the other side of the living room wall, but that will then require running a long cable to connect to the stereo.
Bottom line: 50ft. range of AX may be reduced when used in old (1920's era) houses (thick, plaster walls). Actual distance between AX and iMac is probably 30-40 feet, though they are separated by at least 3-4 walls. If repositioning to other side of wall doesn't do the trick, I may need to step up to Extreme.
I hope this helps others that might have similar problems.

Older airport express not showing up in airport utility - want to extend network

I just bought a new Airport Extreme so that I could use my older Airport Express to extend my wireless network. The Extreme is working fine. Set up was easy. Airport Utility isn't finding my express - no matter what I do - and I'm at a total loss. Please help me find it and then extend my network. Thanks!

If you decide to keep the new AirPort Extreme, you will need a newer "n" version of the AirPort Express if you want to try to extend the network using wireless only.
A "refurbished" Model A1264 would work, but it will only extend one band from your dual band AirPort Extreme.
A "new" Express, Model A1394 would be recommended since it will extend both bands.
You do have the option to use the old AirPort Express, but that would involve using a permanent wired Ethernet connection between the AirPort Extreme and AirPort Express.
Unfortunately, it is not possible to predict wireless performance in advance when the signal must pass through numerous walls and or a ceiling. For that reason, it would be a good idea to understand the store's return policy in advance if you want to try a new or refurbished Express.

Airport Express not showing up on airport utility

I've connected Aiport Express for the forst time via an internet cable to my wireless router, and Have got the flashing amber light.
Have I missed something, does anyone know/
Thanks
Chris

Temporarily, connect an ethernet cable from your computer to the AirPort Express (AX) to see if that helps AirPort Utility "see" the AX.
In order for the AX to extend the signal from the Airport Extreme (AEBS), the following must occur:
Wireless Mode set to Extend a Wireless Network
Wireless Network Name must exactly match the name of the network created by the AEBS
Wireless Security must exactly match the wireless security setting on the AEBS
Wireless Password must exactly match the wireless password setting on the AEBS

How to setup a guest network when the dialogue boxes do not show up in AirPort Utility 6.1

How do I setup a guest network when the dialogue boxes do not show up in AirPort Utility 6.1?
I see screenshots where there are boxes to 'enable' guest network but these simply do not apear on the Wireless tab in AirPort Utility

I now have a guest account, thanks to you!
I did the factory reset and was able to set up the guest account.
There were 3 problems, all of which I was able to solve.
The first problem was connect to Ethernet, which I selected by WAN port, as shown in the first screen shot. This page used to read just Ethernet and the Bridge Mode.
The second problem was whether to share a range of addresses or share a public IP address. I selected share a public IP address as shown in the first screen shot. I had tried the range of IP addresses in my earlier attempts, the ones that failed. Hopefully this will have no effect.
I have forgotten what the third problem was - only excuse is a few too many flavored drinks. I didn't have any problems solving it though.
What is really weird is I can log on to Guest and use on my iPad (first generation), my wife's iPod Touch (third generation), and my wife's 2011 MacBook Pro. I can't log onto Guest on my 2008 iMac, even after a restart. I get the image below.
Since I don't lug my iMac around a lot and it is connected by Ethernet, while my little make it right brain says figure this out, I am not going to worry about it.
Thank you again for your time and patience in helping me solve this.
Eric Root

HAAALP!!! AIRPORT EXTREME NOT SHOWING UP ON AIRPORT UTILITY

I have two airport extremes one to make network and one to expand it. the one i have to make the network is working fine and is a FINE peice of machinery. but the second one i have to extend my network will not show up on airport utility. and no i am not a stupid and didnt plug in the wires right everything is in perfectly and i use to be able to configure it then one day it just stops so i reset and configure it with airport utility. but after it restarts the airport and updates it. it will not show up on airport utility. PLZ help i have tried everything reset it a millions time and some times it will show up then i will change the settings again!! and it will not show up again!!!!! plzz plzz HELP

they are already in the same room and i am doing it on the same computer and it feels like it has gone into a land it can not come back from. also i just realized that it stays amber constantly like its in its startup process. and after a while the light just goes OFF. so idk and i have hard reset it and isnt it supposed to flash lights (cause it doesnt) when i hard reset it. well idk its weird its like it take forever to startup or something cause all of the sudden it will show up on airport utility but after i configure it again it restarts and can not be found again. ;{

Air port express not found by my mac

Hallo all, I want to extend my wlan, therefore I want to install an additional air port. I have already a time capuse with air port. Now my question:
Do I neet to connect the new air port with a wire? I thougt the connection is wireless? Unitl now the new air port is not found by my mac within the utility air port program. Why? Please help! Thank you, Kailash

To help facilitate setting up your extended network, I would recommend the following:
Perforrm a "factory default" reset on the AirPort Express base station.
Temporarily connect the Express to the Time Capsule using an Ethernet cable between them.
Once you have configured the extended network, you can now disconnect the Express from the TC and place it at the desired location.

Airport express not showing up in airport utilities

Hi everyone,
First off, I am very new to the mac OS so please excuse obvious misstakes.
I received my macbook pro last monday combined with an aiport base station and an express. I planned to use the express for the airtunes at home and use it as a router with printer attached at work. My home situation works great. I have a harddisk attached to my extreme base station and can stream that content via my macbook pro to the express (which does drop connection quite frequently).
However, when at work cannot seem to get any connection to express. I have tried every single configuration. PLugged in with ethernet, without, with printer, without. I have tried resetting, unplugging. I made a new profile at home before i left which is setup to make the express a wireless router. An option I had not found the previous time I could not connect to it. But alas, this makes no difference.
If I could just make ANY connection to it i would be able to figure it out but i cant. Not even after a reset when the express is 10 cm from the laptop.
PLease Help me,
thanks in advance

Your new iMac should not have any issues connecting to the 1st generation AirPort Express Base Station (AX).
When having difficulties accessing the AirPort thru the AirPort Utility, try the following, in order checking accessibility with the utility after each step:
Check the local connection. If you are trying to access the AirPort wirelessly, make sure that you are connected to its wireless network before running the AirPort Utility to administer it. If you are still unable to access it with the utility, temporarily connect your computer directly using an Ethernet cable to one of the base station's LAN ports.
Power cycle the base station. Remove the power adapter's plug from the power outlet, and then, wait 15 seconds before plugging it back in.
Perform a "factory default" reset on the base station.

USB Hard Drive not showing up in AirPort Utility

I have been using this AirPort Extreme for over two years now and it's been working fine. I finally decided to buy a self-powered USB hard drive so I can share it over the network. However, after I unpacked the hard drive, connected it to my Mac and reformatted it to HFS+ Journaled and GUID. I plugged the hard drive into my AirPort Extreme's USB port and waited. I looked in my AirPort Utility and saw nothing in the disk list.
I spent hours searching online and discovered that I am not alone in this problem, although solutions are rare. I did try one solution where I hooked up the USB hard drive to a powered USB hub and the hub into AirPort Extreme. It actually worked once and after I rebooted everything, even though the hard drive still showed up in the disk list, no computers can connect to it. Although if I connect the hard drive directly to a Mac, it would still work perfectly.
Having a USB hub is not a long term solution not that it's working anymore anyway. I would appreciate any suggestions you may have, thanks!

Weilishu wrote:
Thanks for the response. However, I'm not sure what you mean.
So far my experience is far from "Just connect the external hard drive to the USB port on the back of your AirPort Extreme and — voilà".
did you read the support article Daddy linked ? it clearly says
JGG

AE does not show up in Airport Utility

Hello,
As a disclaimer, I know next to nothing about wireless networks. Here is what I have: 2 G5 towers and MBP. Tower is NOT wireless. Cable comes in and goes to modem > modem to Airport Base Station > to D-Link Router. All computers have a direct connection to the D-Link providing 10/100/1000 connection. I also have an Airport Express that is connected to our stereo system to stream iTunes... at some point, and I am not sure when, the AE quit working. I can connect from the laptop upstairs to the Base Station downstairs... but when I open the Airport Admin utility, the Express simply doesn't show up? I have a blinking amber light on the Express. I did a hard reset on all units (AB, AE, and router); but nothing. At one point, this configuration worked just fine. My wife went to use it today and that is when we found out that it doesn't work anymore. What am I doing wrong??
Mike

If you are using AirPort Utility 6.x, or AirPort Utility for iOS devices, printers do not "show up" in the application at all.
This has no bearing on whether or not the printer will function as long as you have installed the printer using Print and Fax on your Mac.
If you are trying to print from an iOS device, you will not be able to accomplish this unless you add additional software to the iOS device.

Express not showing up in admin utility

I have an ibook g3 with an original airport card installed. I am trying to set up a wireless network at my home with an airport express, but it is not showing up in the admin utility and setup assistant. What do I need to do?

Yes, the same thing has happened to me. My internet connection was working fine, but I couldn't see my Airport Express in the Admin Utility nor could I see my remote AirTunes speakers in iTunes. After a restart, everything came back to normal. So if anyone else is facing something similar, try that before panicking.
iMac G5, iBook G3 Mac OS X (10.4.5)

Airport Extreme still not showing up in Airport Utility

So after my own router wasn't working, a family member passed their Airport Extreme down to me and cited Apple's extremely easy set-up. Plug in the power, plug in the ethernet cable, then we should be good to go.
The green light is on (not flashing) but when I create a new network, the IP shows up but it says that it cannot connect with the internet. Then I tried to see if it would be found using Airport Utility. It's been 15 minutes and it's still not found. Internet in the house is working just fine (using roommate's connection now) but I'd like to get this set up ASAP.
What are the problems here and how can they be solved?
If it helps any, I'm using last year's Macbook Pro model and the Airport Extreme gen 5.

If AirPort Utility looks like the following, click the button at the upper left - the one labeled "Other Wi-Fi Devices". Determine if it appears in a dropdown menu:

USB printer not showing up in airport utility

Hey guys,
I am trying to set up my father-in-law's new Time Machine with an HP Deskjet 5850 printer. It is a simple USB connection, however I cannot get it to work, even though I had the printer working on my AEBS in my apartment a few days ago (I gave him the printer, as I got a new one). I have tried everything, yet even with the USB connection the printer won't show up in the airport utility "printer" pane. Any suggestions?

I troubleshooted the printer all night...finally came to a somewhat-acceptable solution by wiring the printer via the ethernet ports on the back of the computer. If possible, those with trouble could try that method. It worked for me. Still unhappy with the functionality of the USB considering how well the AEBS worked. The AEBS also showed the printer in the airport utility window before I set it up in Print and Fax. I have no idea why Time Capsule is different, it is essentially AEBS+HDD.

HT3728 Time Capsule LED is solid Amber, will not show up in Airport Utility after any resets. Ideas?

Went to update my TC after adding my AppleID to the "Back to Mac" menu and in the Airport Utility screen a meesage popped up saying "An error ocurred while reading the configuration" and the TC disappeared from the Airport Utility screen. Now there is just a solid amber light. Unplugging the unit for over a minute and then plugging it back in has the same result. A soft reset does nothing, a hard reset does nothing, and a factory reset gets the amber light blinking but when I release the reset it goes back to solid amber. None of these resets gets the TC to show up in the Airport Utility.
I appreciate any help. Thanks.
Model: A1409 Time Capsule 2TB

The solid amber light is an indication that the TC cannot get out of startup mode, likely due to a power supply component failure.
Solid amber is not power supply.. it is a dead hard disk.. the TC cannot finish its boot if the hard drive is not working.
Jeepaxle
If the TC is in warranty or you have applecare on any computer Apple should replace it..
Otherwise it is the poor WD green drive they now use..
Open the TC and replace it.
Sometimes a low level format will revive them.. but I never trust a drive again that died.. Look for a 2TB hitachi or Toshiba.. (same thing). Far better than WD green.
http://www.ifixit.com/Device/Apple_Time_Capsule

Airport Express Not Showing up in Admin Utility

Have an Intel iMac, and tried to set up AX yesterday. Using SBC DSL internet connection (2-wire system). Plugged phone line into 2-wire router, ethernet cable between router and AX, powered both up. Router shows 3 green lights, indicating that everything is "good." Likewise, AX shows up with a green light. On the iMac, I never got the generic "Airport Express Network" or anything, but did have 2WIRE381 recognized (presumably as my AX network). I am able to connect to the 2WIRE381, and show a strong signal. However, I cannot connect to the internet, nor can I configure AX via the the Admin Utility (nothing shows up). I've tried both soft and hard resets, powering off the router, restarting the iMac, ... nothing seems to work. AX also not visible in iTunes (since no internet connection).
Any thoughts? One thought that I had ... is it possible that I am picking up a neighbor's signal, and that is why I can't configure it? My AX is about 30-40 feet away (single level house, 1200 sqft.) with probably 3-4 walls between AX and iMac.
Any ideas/suggestions greatly appreciated.

Answering my own post ...
I first directly connected the AX to the iMac using the ethernet cable, and was able to configure the AX (not sure that I actually had to do this, as my issue was probably due to poor signal strength - as described later). I then moved the AX back to the living room, and was able to connect again, but soon it was dropped. Determined that the signal was weak. I played with positioning the AX to optimize signal, and now am able to get OK signal (only about 1/3 strength, based on number of bars in "fan" shaped icon in menu bar). Was able to stream iTunes to stereo as well, which is great. Also determined that the 2WIRE system that Airport was trying to set up WAS my neighbor (and not my gateway/router). If you don't see "Apple XXXXX" base station and network listed when you are in Airport Admin Utility or Internet Connect (which I didn't, but since I was using 2WIRE gateway/router, assumed that it was my AX when the 2WIRE appeared in the Airport network connection option), then the AX is not properly set up (weak signal or other problem).
So, with the AX in the living room (front of the house), and the iMac in the sun room (back of the house), I am able to get OK, but not great signal from AX. So far, seems to be sufficient to connect to internet and stream iTunes. I may see if I can reposition the AX on the other side of the living room wall, but that will then require running a long cable to connect to the stereo.
Bottom line: 50ft. range of AX may be reduced when used in old (1920's era) houses (thick, plaster walls). Actual distance between AX and iMac is probably 30-40 feet, though they are separated by at least 3-4 walls. If repositioning to other side of wall doesn't do the trick, I may need to step up to Extreme.
I hope this helps others that might have similar problems.

Air Port Express not showing up on Airport Utility scan

Similar Messages

Maybe you are looking for