AirDrop with LAN connection

Hi,
My MacBook Pro lost suddenly its wifi card (dead), and I lost with it the AirDrop option in Context menu/Share (right-click mouse). Is there anyway to bring it back (AirDrop in Share menu)? Given that AirDrop is still possible by drag-and-drop in Finder.
Thanks for your help,
And sorry for my english .

it just does not load the pages
after about ten minutes (really!) of loading with the blue bar not moving safari says nothing!
firefox in the status bar says: transferring data from .....[link to the Microsoft website i'm trying to connect to] and then nothing!
mac messenger says: sing in to Microsoft messenger failed because the service is not available or you may not be connected to the internet (retry - cancel)
and adium says something similar to messenger
itunes does not say anything, i just have the bar with "connecting to the itunes store" and then nothing
is there some kind of hateful firewall in macbook pros that excludes microsoft?!?! eheh
no, just joking, the problem i have is real, what can i do?
hope i gave you enough informations Rodney

Similar Messages

Trouble with LAN connection and DHCP

I would greatly appreciate any input on this issue.
Some reason when I installed Arch from the 2009.08 release it would always fail when I try to use dhcpcd eth0 or dhclient eth0.
It would say:
... Looking for carrier
... timed out.
I thought that it might be the cable or the router but I have tried multiple cables and routers in different locations, and it works fine when I run in Windows.
Nothing I have tried has worked, I have been searching for forums for a similar issue. I have had to use a wireless connection for everything internet based.
Last edited by phoenix89 (2009-09-14 02:41:55)

I meant it works fine in Windows...
but the output for the lspci -v is:
lspci -v
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 671MX
Subsystem: ASUSTeK Computer Inc. Device 1af7
Flags: bus master, medium devsel, latency 64
Kernel modules: sis-agp
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fa000000-fdefffff
Prefetchable memory behind bridge: 00000000d0000000-00000000dfffffff
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] (rev 01)
Flags: bus master, medium devsel, latency 0
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev 01) (prog-if 80 [Master])
Subsystem: ASUSTeK Computer Inc. Device 1af7
Flags: bus master, medium devsel, latency 128
I/O ports at 01f0 [size=8]
I/O ports at 03f4 [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=1]
I/O ports at fff0 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_sis
Kernel modules: ata_generic, pata_acpi, pata_sis, ide-pci-generic, sis5513
00:03.0 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device 1af7
Flags: bus master, medium devsel, latency 64, IRQ 20
Memory at f9fff000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:03.1 USB Controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device 1af7
Flags: bus master, medium devsel, latency 64, IRQ 21
Memory at f9ffe000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:03.3 USB Controller: Silicon Integrated Systems [SiS] USB 2.0 Controller (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device 1af7
Flags: bus master, medium devsel, latency 64, IRQ 22
Memory at f9ffd000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:04.0 Ethernet controller: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter (rev 02)
Subsystem: ASUSTeK Computer Inc. Device 1815
Flags: bus master, medium devsel, latency 0, IRQ 19
Memory at f9ffcc00 (32-bit, non-prefetchable) [size=128]
I/O ports at cc00 [size=128]
Capabilities: <access denied>
Kernel driver in use: sis190
Kernel modules: sis190
00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA Controller / IDE mode (rev 03) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. Device 1af7
Flags: bus master, medium devsel, latency 64, IRQ 17
I/O ports at c800 [size=8]
I/O ports at c400 [size=4]
I/O ports at c000 [size=8]
I/O ports at bc00 [size=4]
I/O ports at b800 [size=16]
I/O ports at b400 [size=128]
Capabilities: <access denied>
Kernel driver in use: sata_sis
Kernel modules: ata_generic, pata_acpi, sata_sis, ide-pci-generic
00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Memory behind bridge: fdf00000-fdffffff
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=06, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fe000000-febfffff
Prefetchable memory behind bridge: 00000000f6000000-00000000f8ffffff
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:0f.0 Audio device: Silicon Integrated Systems [SiS] Azalia Audio Controller
Subsystem: ASUSTeK Computer Inc. Device 1203
Flags: bus master, medium devsel, latency 0, IRQ 18
Memory at f9ff4000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
01:00.0 VGA compatible controller: nVidia Corporation G96M [GeForce GT 120M] (rev a1) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device 1a42
Flags: bus master, fast devsel, latency 0, IRQ 10
Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
Memory at d0000000 (64-bit, prefetchable) [size=256M]
Memory at fa000000 (64-bit, non-prefetchable) [size=32M]
I/O ports at dc00 [size=128]
Expansion ROM at fde80000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel modules: nvidiafb
02:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01)
Subsystem: Device 1a3b:1067
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at fdff0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
Kernel modules: ath9k

Does air play work over lan connection on apple tv

I have an Apple TV and want to use the LAN conenction to coneect to my subnet wihch is the same one that the Air connects Wifi to and as long as I have them both connected to the same WiFi Airplay works. When I plug in the LAN it stops. I was hoping Apple TV2 with LAN connection and then WiFi from the Ipad and be able to use AirPlay. Hoping...

Your MacBook Air needs to be running OS X Mountain Lion (10.8)
Only mid 2011 Mac computers support AirPlay Mirroring > About AirPlay Mirroring in OS X Mountain Lion

Lost LAN connection

I set up Total Broadband 2 weeks ago with LAN connection to my PC and it worked first time. Other laptops/netbooks in the house connected wirelessly without any problem. On Thursday evening I picked up my emails before closing down and on Friday morning I had no connection and haven't had it since then - yet the laptop and netbooks still work perfectly well both wirelessly and by connecting the LAN cable - so it's not a faulty cable. For some reason my Realtek PCIe is not being seen and yet according to Windows the device is working properly. I can't use the desktop tools because I can't get on line so am posting this on a laptop. Can anybody help please?

Hi I would suggest either a faulty network card or try reinstalling the cards drivers and try again
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Lan connectivity Issue on autonomous AP with throttles

          Hello,
I encounter a strange problem on several AP 1242 in version 12.4(25d)JA1 of a customer :
He has 10 autonomous AP covering a factory and is using them for laptop connectivity and TOIP with mainly 7921 Cisco Wifi Phones.
The phones are configured to use only 802.11a.
The APs loose LAN connectivity randomly and therefore the clients don't work anymore.
The AP are connected on a 2960 and a 3560 wich are in turn connected on a 3750 wich route the trafic.
After checking spanning-tree no loops are present.
When I check the counters on the AP involved I see the "trhottles" and "ignored" counters incrementing on the fa0 link of the AP impacted wich mean I think it can't handle the incoming traffic. This incoming traffic seems not to be too big however. I can see drops on the switch interface connecting the AP.
There is a lot of roaming on the AP due to people walking in the factory with their wifi phones.
Here is a view of the fa0 counters :
AP1242-LOGIST#sh int fa0
FastEthernet0 is up, line protocol is up
Hardware is PowerPCElvis Ethernet, address is 001d.a1ce.26e2 (bia 001d.a1ce.26e2)
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Full-duplex, 100Mb/s, MII
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/160/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 81000 bits/sec, 53 packets/sec
5 minute output rate 29000 bits/sec, 26 packets/sec
     7447113 packets input, 674891974 bytes
     Received 286839 broadcasts, 0 runts, 0 giants, 549631 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 549631 ignored
     0 watchdog
     0 input packets with dribble condition detected
     4422100 packets output, 609868806 bytes, 0 underruns
     0 output errors, 0 collisions, 4 interface resets
     1 unknown protocol drops
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out
Here is a small part of logs concerning roaming, i don't see errors or log indicating that something is wrong nor in the switches log :
Jun 6 12:57:27.007: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001E4A3EE15D 001e.4a3e.e15d Associated KEY_MGMT[WPAv2 PSK]
Jun 6 12:57:42.499: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 12:58:02.620: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 12:58:03.653: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 12:59:15.564: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 12:59:15.564: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 12:59:41.905: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 442b.0355.ab28 Reason: Previous authentication no longer valid
Jun 6 12:59:54.728: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP442B0355AB28 442b.0355.ab28 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:01:12.541: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:02:35.841: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001e.4a3e.d875 Reason: Previous authentication no longer valid
Jun 6 13:02:36.489: %DOT11-6-ASSOC: Interface Dot11Radio0, Station   ec85.2f7c.c837 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:03:29.256: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:03:29.256: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:04:32.754: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001E4A3ED875 001e.4a3e.d875 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:06:47.858: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001e.4a3e.e15d Reason: Previous authentication no longer valid
Jun 6 13:07:18.107: %DOT11-6-ROAMED: Station 001f.6c7a.5101 Roamed to 001d.a2bb.15b0
Jun 6 13:07:18.107: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001f.6c7a.5101 Reason: Sending station has left the BSS
Jun 6 13:07:38.109: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:07:42.031: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:07:42.031: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:07:46.489: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001F6C7A5101 001f.6c7a.5101 Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:27.712: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:44.502: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:08:44.572: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:56.778: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:08:56.779: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:09:17.874: %DOT11-6-ROAMED: Station 001f.6c7a.5101 Roamed to 003a.9a92.8d70
Jun 6 13:09:17.874: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001f.6c7a.5101 Reason: Sending station has left the BSS
The AP are configured as follow :
Current configuration : 5184 bytes
! No configuration change since last restart
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP1242-LOGIST
logging rate-limit console 9
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
clock timezone gmt+1 1
clock summer-time gmt recurring last Sun Mar 2:00 last Sun Oct 3:00
dot11 syslog
dot11 vlan-name Data vlan 11
dot11 vlan-name Voix vlan 14
dot11 vlan-name Webguest vlan 5
dot11 ssid WLAN_data
   vlan 11
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii 7 10600C0E261B173C252203797479633F371A29
dot11 ssid WLAN_voice
   vlan 14
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii 7 080F49592A1500203B2D25567A7A7622263C0C
dot11 ssid Webguest
   vlan 5
   authentication open
   mbssid guest-mode
dot11 wpa handshake timeout 1000
dot11 arp-cache
dot11 priority-map avvid
dot11 phone
power inline negotiation prestandard source
class-map match-all _class_voice0
match ip dscp ef
class-map match-all _class_voice1
match ip dscp cs3
policy-map voice
class _class_voice0
set cos 6
class _class_voice1
set cos 3
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 11 mode ciphers aes-ccm
encryption vlan 14 mode ciphers aes-ccm
ssid WLAN_data
ssid WLAN_voice
ssid Webguest
mbssid
power client 17
channel 2472
station-role root
dot11 qos class voice local
    admission-control
    admit-traffic narrowband max-channel 75 roam-channel 6
dot11 qos class voice cell
    admission-control
no cdp enable
infrastructure-client
interface Dot11Radio0.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
bridge-group 5 subscriber-loop-control
bridge-group 5 block-unknown-source
no bridge-group 5 source-learning
no bridge-group 5 unicast-flooding
bridge-group 5 spanning-disabled
interface Dot11Radio0.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio0.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
bridge-group 14 subscriber-loop-control
bridge-group 14 block-unknown-source
no bridge-group 14 source-learning
no bridge-group 14 unicast-flooding
bridge-group 14 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 11 mode ciphers aes-ccm
encryption vlan 14 mode ciphers aes-ccm
ssid WLAN_data
ssid WLAN_voice
ssid Webguest
no dfs band block
mbssid
channel dfs
station-role root
interface Dot11Radio1.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
bridge-group 5 subscriber-loop-control
bridge-group 5 block-unknown-source
no bridge-group 5 source-learning
no bridge-group 5 unicast-flooding
bridge-group 5 spanning-disabled
interface Dot11Radio1.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio1.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
bridge-group 14 subscriber-loop-control
bridge-group 14 block-unknown-source
no bridge-group 14 source-learning
no bridge-group 14 unicast-flooding
bridge-group 14 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
speed 100
full-duplex
no cdp enable
hold-queue 160 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
no cdp enable
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
no bridge-group 5 source-learning
bridge-group 5 spanning-disabled
interface FastEthernet0.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
no bridge-group 11 source-learning
bridge-group 11 spanning-disabled
interface FastEthernet0.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
no bridge-group 14 source-learning
bridge-group 14 spanning-disabled
service-policy input voice
service-policy output voice
interface BVI1
ip address 10.17.10.5 255.255.255.0
no ip route-cache
ip default-gateway 10.17.10.254
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging trap warnings
logging 10.15.51.115
no cdp run
bridge 1 route ip
line con 0
line vty 0 4
sntp server 10.15.1.50
sntp broadcast client
end
Does someone ever experienced a similar problem ?
When I shut radio interfaces they're is no more problems on the LAN. Can this be an overlapping coverage issue ?
Can someone please give me advices on how to troubleshoot this issue ?
Thank you in advance as I'm a bit stuck.
Best Regards,

     Hi Scott,
Thanks for your reply.
Do you think this can be the origin of the issue my customer encounters or is it only to be standard ? As this change will have to be made on all clients, if there is a chance it solves the problem I will do it ASAP, if not I will delay it in a less busy period :-)
Can the constant roaming associations and dissasociations overload the AP and make it stop responding on the LAN or is it only a throuhput problem ?
Thanks in advance for your answer.
Best Regards,

Is it possible to control (screen share) my Mac Book on my PC over a LAN connection with fullscreen 1920x1080 resolution AND sound?

I've fiddled with Team Viewer and was able to control my Mac on my PC, but it wasn't over my LAN connection (it was slow), and it was a small windowed view without the Mac's sound. I want to cotrol my Mac, with my PC over LAN and on a 1920x1080 resolution with the Mac's sound on my PC.
(Sry for a almost report of this (https://discussions.apple.com/thread/4031259) but I forgot to ask about the sound).

well there is a program called logmein found at logmein.com. it fixes your resolution problem, but the speed is still not the best due to a lag still. As long as internet connections are decent, the lag should be minimal

Can some please help me with the Wireless LAN Connection Configuration?

I want to configure WLC in my Testing Lab , need help with the step by step configuration of WLC.

Please go through the below link for the Basic Wireless LAN Connection Configuration Example.
The below link has end – end configuration steps with the images.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/68005-wlan-connect.html
Have i answered for your query.

Can my iPhone does Wifi Sync with PC (LAN connected through wifi router)?

I have connect my PC to a wifi-router,
and I also connect my iPhone with this wifi network
but i can't find my iPhone as device in iTune (as we normally see it when we use notebook
Question: Is this normal? or something go wrong with my connection?
Kindly advise.
Thank you very much

Thank you very much Diesel vdub,
I have followed your kind advice; syny my iPhone with new PC via physical cal ble connection. However, it still not show in device list when I unplug cable. Formerly, I can sync through wifi from my notebook but now I can't since I have changed to use PC (which connect to the same wifi router).
Please advise if somewhere I did something wrong or where should i do more
Thank you very much

HP Slate 21 Kit Kat OTA Update Fix for Audio Quality and LAN Connectivity

Recent Over The Air (OTA) update for Slate 21 Update
Link to thread discussion here, fix listed below -
ISSUE:
A previously applied HP Slate 21 Kit Kat Update (Android 4.4.2) over the air (OTA) update may have caused issues with audio quality or wireless LAN connectivity.
Audio Quality: Bass response will be poor. Audio will play but bass frequencies will be lacking.
WiFi Issue: 5 GHz band not functioning properly
Status:
A new update (17r25.1-011-11-WW) has been released over the air (OTA) to end users
Resolution:
Apply update 17r25.1-011-11-WW
If the user was previously on 17r25.1-010-10-WW then a Factory Reset should be performed to complete the resolution.
I work for HP, supporting the HP Experts who volunteer their time and technical knowledge to help others.

Pebbles65,
Thank you for visiting our English HP Support Forum. We are only able to reply to posts written in English. To insure a quick response it would be advisable to post your question in English. The following links are here to assist you if you prefer to post in the following Language Forum.
English: http://h30434.www3.hp.com
Spanish: http://h30467.www3.hp.com
French: http://h30478.www3.hp.com
Portuguese: http://h30487.www3.hp.com
German: http://h30492.www3.hp.com
Korean: http://h30491.www3.hp.com/t5/community/communitypage
Simplified Chinese: http://h30471.www3.hp.com/t5/community/communitypage
Cheers,
KarolB
I work for HP

Disable WLAN when LAN connected - how do I do?

Hi,
We are in the process of migrating from HP notebooks to Lenovo. We used to set a BIOS setting called "LAN/WLAN Switch" in the HP notebooks, which makes the WLAN to disable when the LAN cable is plugged in or the pc is docked
Where do I find a similar setting in Lenovo notebooks?
We need it because LAN and WLAN is on separate subnets, and Windows XP has trouble working with both nets at the same time. Users compalins about loss of network connectivity if both nets are enabled at the same time.
There may be a way to configure LAN/WLAN-switching in the Lenovo software, but we prefer to use the build in WLAN functionality in Windows, not using Access Connection or similar third party WLAN software. Our experience shows that uses often have difficulties finding out how to use third party WLAN software when traveling and need to connect to other WLAN's. The build in Windows WLAN software has the advantage that it is always the same, no matter which brand or model of pc they are using.
Regards,
Peter
www.skov.dk

Check out Wireless AutoSwitch at http://www.wirelessautoswitch.com it does what you are asking.
What is Wireless AutoSwitch?
Wireless AutoSwitch runs as a service and will automatically disable your wireless card when you connect to a LAN (hard wire) connection, and re-enable the wireless card when there is no LAN connection. This ensures that you are always using the fastest connection for network traffic. In the office this helps reduce redundant network connections, while still helping your employees seamlessly transfer from wired to wireless network connections.
For offices that are wireless security conscious this application makes sure the laptop's wireless card is off when the user is wired into your network, preventing bridged connections and preventing someone from the outside hacking your network through a laptop's wireless card.

T60p & Windows 7 Pro and Bluethoot problem with Access Connections.

Hi,
I reinstalled Windows 7 Pro (64bit) at my T60p laptop.
I use Access Connections (v. 5.97) manage my wi-fi, lan connections.
(installed with all features lan, wi-fi, modem etc.)
So here is problem.
When I start Access Connection. Bluethoot goes ON ...
Trying disable Bluetooth via Access connectios (Power Off), but it's still going "ON" and stays "ON"...
Any good solution to keep bluethoot off without disable it at bios?
Earlier version of Access Connections keeps bluetooth OFF...
/P

If you are not using the Bluetooth and you want to disable it, the easiest way is to disable the device in the Device Manager.
Go into the Device Manager by searching for Device Manager in the start menu, Open the Device Manager and select hardware, choose the Bluetooth device, right click, and finally choose 'disable'. If you want to use the Bluetooth device in the future you will have to return to the Device manager, right click and 'enable' the device.
I hope this information has been helpful, please let me know if you have any further questions.
Thank you for being a part of the Lenovo Family,
Catie
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Donate KUDOS and Click "Accepted Solution"

I cant make a boot diskette with lan driver

hello
i am trying to make a boot diskette with lan driver for the 865 chipset and for the pt880 m/b
but i cant find the onboard lan driver for dos anywhere
i want the computer to connect to another and take a ghost image from it
i need the lan driver for dos
please help

This one works perfectly with my onboard Intel Gigabit LAN. I use it all the time to make back-up images across my network.

Ask the Expert : Initial Set Up and LAN Connectivity for Cisco UCS Servers

Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about related to the initial setup of UCS C & B Series which include LAN connectivity from the UCS perspective with Cisco subject matter expert Kenny Perez.
In particularly, Kenny will cover topics such as: ESXi/Windows installations, RAID configurations (best practices for good performance and configuration), VLAN/Jumbo Frames configuration for B series and C series servers, Pools/Policies/Upgrades/Templates/Troubleshooting Tips for blade and rack servers, Fabric Interconnects configuration, general compatibility of Hardware/Software/drivers amongst other topics
Kenny Perez is a technical leader in Cisco Technical Assistance Center, where he works in Server Virtualization support team. His main job consists of supporting customers to implement and manage Cisco UCS B series and C series. He has background in computing, networking, and Vmware ESXi and has 3+ years of experience support UCS servers and is VCP certified.
Remember to use the rating system to let Kenny know if he has given you an adequate response.
This event lasts through October 10th, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

Hi,
Actually we have UCS 6248 fabric interconnect - first twelve ports are enabled and same in Cisco UCS Manager.
But when more port will be active by expansion module then UCSM can manage that too or need any other licence for UCSM too?

802.1x on a wired Lan Connection

Dear Community,
i have the job to connect a Windows CE 6.0 device to a Network (wired) with 802.1x. The switch to wich i connect the device is operating as authenticator and the Wince device is the supplicant. A Radius Server with AD is also present .
All the informations and samples that i can find are relating to wireless LAN connections (WZCSVC). A description of the EAPOL API is also absent (or i was not able to find it).
I'm afraid that Wince 6.0 is not prepared for using 802.1x over a wired connection like Win XP can, but i'm not sure about that. I can not find a definite statement whether it is possibe or not.
Does anybody know if it is possible and/or how i can solve this problem.
Regards Achim

Community,
anybody has answer to this problem? I have to do the same thing...
Achim,
did you solve this problem?Thank you
in advance for any help you
can provide.
Regards Bruno

Hang of RMI call when LAN connection removed

I have a client server application with comms using RMI across a TCP/IP LAN. We are in test at the moment and one of the tests is to ensure that when the LAN connection is removed, the client application handles it correctly.
We have discovered that if we pull the LAN whilst an RMI call is in progress, the call never returns, even if we subsequently plug the LAN back in. Why should this be? I would have expected a RemoteException as soon as I pull the LAN out. How come the thread gets deadlocked?
Note that we are running JRE 1.2 on the client (they are soon to be updated but it's 1400 remote, unattended sites so it's an expensive process to update to a recent JRE).
Thanks
Mat

Thanks ejp - couple of dollars coming your way. Be a couple more if you (or anyone else) can help further.
Firstly, how would I set this property in the code?
Secondly, would it be set in the client or the factory (yes we do have one)? If it's in the factory, will that help me from the client side (that's where I need it to work). I looked up the responseTimeout property and it looks like this is more for the server to close incoming connections. The problem I have is on the client side - I need the client (i.e. that is making the RMI call via an exported remote object) to be able to kill off a call that has going too long (for instance because it can't detect the closed TCP connection).
Maybe I've misunderstood the documentation I've found but that's how I read it.
Thanks again!
Mat

AirDrop with LAN connection

Similar Messages

Maybe you are looking for