Airobet 1142n erased flash and set baud rate to 115200, cant send any commands

Hi,
I was trying to reset the WAP to default settings and after trying a bunch of things, I decided to erase everything in flash and send over the com port. I tried sending at 9600 but the file never made it. So I used the ap: set BAUD 115200 command and changed to the same on Teraterm, now all I get is gibberish when entering any key. I get this far:
Base Ethernet MAC address: c4:7d:4f:xx:xx:xx
Waiting for PHY auto negotiation to complete TIMEOUT !
done
Ethernet speed is 10 Mb - HALF duplex
The system has encountered an error initializing
the Ethernet port.
The system is ignoring the error and continuing to boot.
If you abort the system boot process, the following
commands will re-initialize Ethernet, TFTP, and finish
loading the operating system software:
    ether_init
    tftp_init
    boot
The system is unable to boot automatically because there
are no bootable files.
C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Wed 14-Oct-09 18:59 by prod_rel_team
ap:
then when I try to type something I get :
ap: üüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüü
*** line too large ***
Unknown cmd: üüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüü
ap: üüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüü
*** line too large ***
Unknown cmd: üüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüü
Am I screwed?
Thanks.

The system is unable to boot automatically because thereare no bootable files.
Hi,
I think u deleted the IOS from AP. Now u need the new IOS.
Please download the new IOS and put in flash:
Regards
Dont forget to rate helpful posts.

Similar Messages

Airobet 1142n erased flash and set baud rate to 115200, can't send any commands

Hi,
I erased the entire contents of flash and let the WAP boot to AP. I set the baud rate to 115200 now all I get is gibberish. Once it reads from eeprom this shows up:
Waiting for PHY auto negotiation to complete TIMEOUT !
done
Ethernet speed is 10 Mb - HALF duplex
The system has encountered an error initializing
the Ethernet port.
The system is ignoring the error and continuing to boot.
If you abort the system boot process, the following
commands will re-initialize Ethernet, TFTP, and finish
loading the operating system software:
    ether_init
    tftp_init
    boot
The system is unable to boot automatically because there
are no bootable files.
C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Compiled Wed 14-Oct-09 18:59 by prod_rel_team
ap: üüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüü
*** line too large ***
Unknown cmd: üüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüü
ap: üüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüü
*** line too large ***
Unknown cmd: üüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüüü
It can read from the WAP but doesnt allow me to send commands,
Any ideas?
Thanks

Hi Tyresse,
Please use this:
https://supportforums.cisco.com/message/1255262#1255262
Or
Using the MODE button
You can use the MODE button on 1100 and 1200 series access points to reload the access point image file from an active Trivial File Transfer Protocol (TFTP) server on your network or on a PC connected to the access point Ethernet port.
This process resets all configuration settings to factory defaults, including passwords, WEP keys, the access point IP address, and SSIDs.
Follow these steps to reload the access point image file:
Step 1 The PC you intend to use must be configured with a static IP address in the range of 10.0.0.2 to 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1100-k9w7-tar.122-13.JA.tar for an 1100 series access point or c1200-k9w7-tar.122-13.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated. For additional information, refer to the "Obtaining the Access Point Image File" and "Obtaining TFTP Server Software" sections.
Step 3 Rename the access point image file in the TFTP server folder to c1100-k9w7-tar.default for an 1100 series access point or c1200-k9w7-tar.default for a 1200 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power (the power jack for external power or the Ethernet cable for in-line power) from the access point.
Step 6 Press and hold the MODE button while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds), and release the MODE button.
Step 8 Wait until the access point reboots as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, you must reconfigure the access point by using the Web-browser interface or the CLI.
Regards
Dont forget to rate helpful posts.

I clicked erase content and setting before 12 hours but it is not processing till ie not completed till what can i do

i clicked erase content and setting before 12 hours but it is not processing till ie not completed till what can i do

On a 4S the erase should take under 10 seconds. As it has taken longer there must have been data corruption on the phone. Reboot it by holding HOME and SLEEP until an Apple logo appears. If it has not be cleared of all data connect it to iTunes and Restore it. Then erase again.

I done erase data and setting now what i need to do to run my i phon, i done erase data and setting now what i need to do to run my i phon

i done erase data and setting . now what i need to do to start my i phon

i done erase data and setting now what i need to do to start my i phon

After erase data and setting, iphone 3g wont turn on

after erase data and setting, iphone 3g wont turn on. pls help

1. Have you tried plugging it into your computer?
2. Do you have the most updated version of iTunes?
3. Did you try a 'hard' restore. Press home and sleep button at the same time until the Apple logo comes up.

While erasing contact and setting my phone stop working showing round waiting circle and its not geting switched off also

while erasing contact and setting my phone stop working showing round waiting circle and its not geting switched off also

Try a Reset...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430
If no joy...
Connect to iTunes on the computer you usually Sync with and “ Restore “...
http://support.apple.com/kb/HT1414
If necessary Place the Device into Recovery mode...
http://support.apple.com/kb/HT1808
Note on Recovery Mode.
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
Once you have Recovered your Device...
Re-Sync your Content or Restore from the most recent Backup...
Restore from Backup
http://support.apple.com/kb/ht1766

Does labview 5.0 support serial communication at a baud rate of 115200?

When I try to initialise my serial port at 115200 baud rate I get error 32, device paramter error. I'm running labview 5.0. Can anyone help me with this?

I use Serial Port Init.vi to set the baud rate to 115200 with no problem in LabView 5.0 under Windows 95.
I get error 38 when I try a non-supported baud rate.
Do you get the error when you run Serial Port Init.vi directly or just when you call it from your VI? On the diagram where you call Serial Port Init.vi, try placing a probe on the wire going to the baud rate input of Serial Port Init to see what value it's trying to set. You will have a problem going to 115200 if the control on your VI is represented as I16 or U8 or if the data range max doesn't go to 115200.

The main part of the safari page is grey and won't respond/can't type in any commands. I can move back through the previous pages, and even open new ones via the URL, but can't get onto the main part of the page and I can't get onto the 9 page option. !?

The main part of the safari page is grey and won't respond/can't type in any commands. I can move back through the previous pages, and even open new ones via the URL, but can't get onto the main part of the page and I can't get onto the 9 page option. !?
Help, please.

Try clearing Safari's cache : Settings > Safari > Clear Cache (and Clear History)
If that doesn't work then try closing Safari completely and then re-open it : from the home screen (i.e. not with Safari 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Safari app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
A third option is a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

Why has my 3G stopped working on my iphone? It is enabled, and I never had problems with it before, but for about 2 months now it has refused to work and as a result I can't send any attachments such as photos or videos via text.

Why has my 3G stopped working on my iphone? It is enabled, and I never had problems with it before, but for about 2 months now it has refused to work and as a result I can't send any attachments such as photos or videos via text.

Cellular data is a feature from your phone carrier. Have you contacted them to resolve your issue.

Issue setting baud rate for IMAQ using Camera Link

I have a PCIe-1433 camera link board, with a Basler camera. I found that I can set the gain and exposure times directly in the camera using the serial link and serial commands. This works very well. I'm doing this programmatically using the CLAllSerial.DLL.
The serial commands take too long to send in my application due to the default baud rate of 9600, so I was able to send a command to the Basler camera to up its baud rate, then change the baud rate of the camera link serial com port to match it. The result is that I can talk very quickly to the camera. Sweet so far.
However, with both the Basler camera and the camera link com port set to the higher baud rate, I can no longer acquire images using the IMAQ imgXXX commands. I get a timeout from the serial commands that IMAQ must be using to control the camera for image acquisition. Essentially the IMAQ driver doesn't know about the baud rate change. I cannot see how I can tell the IMAQ driver what baud rate to use either. NI MAX also becomes unusable in this situation.
How can I, through the IMAQ driver, increase the baud rate of the serial commands to the camera over the camera link?
Cheers,
Wayne
Solved!
Go to Solution.

David,
I'll try to help if I can. Keep in mind that I'm using a stub into the DLL using Delphi as my development platform. That should not matter.
The DLL I'm tapped into is the IMAQ.DLL for the camera calls to get/set exposure time, gain, etc. The best reference I found for this is the NI-IMAQ help files that get installed with the normal NI install. There are important string constants that you need, to talk to the interface. I can't recall how I found these, but below are mine, in Delphi:
{ These are Basler camera attribute names we care about. }
BaslerCameraGainControlAttributeString = 'Gain'; { string result }
BaslerCameraGainValueAttributeString = 'Gain Value'; { numeric result }
BaslerCameraBitDepthAttributeString = 'Bit Depth'; { string result }
BaslerCameraExposureControlAttributeString = 'Exposure Control'; { string result }
BaslerCameraExposureModeAttributeString = 'Exposure Mode'; { string result }
BaslerCameraExposureTimeAttributeString = 'Exposure Time'; { numeric result }
BaslerCameraMaximumHeightAttributeString = 'Maximum Height'; { numeric result }
BaslerCameraPowerOverCameraLinkAttributeString = 'Power Over CameraLink'; { string result }
{ These are Basler camera attribute values we care about. }
BaslerCameraManualGainAttributeValue = 'Manual';
BaslerCamera12BitDepthAttributeValue = '12-bits';
BaslerCameraMaximumHeightAttributeValue = 2048;
BaslerCameraExposureControlFreeRunAttributeValue = 'Free Run';
BaslerCameraExposureControlTriggeredAttributeValue = 'Triggered';
BaslerCameraExposureModeAttributeValue = 'Manual';
BaslerCameraExposureTimeAttributeValue = 5;
BaslerCameraPowerOverCameraLinkAttributeValue = 'On';
BaslerCameraGainValueAttributeValueMinimum = 33;
BaslerCameraGainValueAttributeValueMaximum = 512;
MaxAttributeStringLength = 100;
The following code snippets, get and set gain and exposure times (I called it shutter speed), in Delphi:
function TNiVision.GetGain : double;
var
TheGain : double;
begin
if GetCameraAttributeNumeric( BaslerCameraGainValueAttributeString, TheGain ) then
Result := TheGain
else
Result := BaslerCameraGainValueAttributeValueMinimum;
end;
procedure TNiVision.SetGain( TheGain : double );
begin
SetCameraAttributeNumeric( BaslerCameraGainValueAttributeString, TheGain );
end;
function TNiVision.GetShutterSpeed : double;
var
TheSpeed : double;
begin
if GetCameraAttributeNumeric( BaslerCameraExposureTimeAttributeString, TheSpeed ) then
Result := TheSpeed
else
Result := 1;
end;
procedure TNiVision.SetShutterSpeed( TheSpeed : double );
begin
SetCameraAttributeNumeric( BaslerCameraExposureTimeAttributeString, TheSpeed );
end;
These then call into the DLL functions imgGetCameraAttributeNumeric and imgSetCameraAttributeNumeric. There is a formatting interface between the above and the actual DLL functions I didn't show that just reforms the Delphi strings attribute names into C null terminated char arrays.
I hope this helps. I've now moved on to using Pylon with GigE cameras, which is a much cleaner interface, but very different code.
Cheers,
Wayne

Termios.h and 921600 baud rate support

Hi,
I've been porting my application from Linux to Mac OS X when I got stuck with serial port support, the lack of 921600 baud rate in particular. There are no definitions of speeds higher than 230400 in the termios.h file. Defining it manually using the constants from Linux doesn't help either.. as it's simply not implemented. Is there any way I can get this?
Thanks in advance,
Piotr

Starting with Tiger, the IOSSIOSPEED ioctl can be used to set arbitrary baud rates other than those specified by POSIX. The driver for the underlying serial hardware ultimately determines which baud rates can be used. This ioctl sets both the input and output speed. The speed will not be reflected in the termios structure.
<pre>
speed_t speed = 14400; // Set 14400 baud
if ( ioctl( fileDescriptor, IOSSIOSPEED, &speed ) == -1 )
printf( "Error %d calling ioctl( ..., IOSSIOSPEED, ... )\n", errno );
</pre>

Excel won't open and error message There was a problem sending the command to the programe

Hi there
I'd be grateful for your help.
I've just bought a new laptop and installed Office 2013. I used Excel 2013, did what I needed to do and saved it. This was 5 days ago.
Today, I've tried opening the file from my desktop and get the error message 'There was a problem sending the command to the program'.
And when I try to open Excel to do the DDE fix, which seems to be the best suggestion, I can't open Excel at all. I've tried to get into it from the Apps screen.
Any help would be gratefully appreciated.
Thanks

Don't seem like this can be fixed so I went back to version 6.0.2 which works good.
I have Chrome now as my default browser and will not use fire fox until they fix it!
Chrome works great!

I have bought an ipad 3, i cant set up my hotmail account, it verifies but i cant send any emails, it does the same on my friends ipad 3, cant find any fixes online hope someone can help

as stated in the title, i cant get my hotmail account to work on any ipad, its the same email address i have used for logging into the app store so i know the email is fine, any help would be great

iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
iPad Mail
http://www.apple.com/support/ipad/mail/
Since you are new to the iPad ....
You can download a complete iPad User Guide here: http://manuals.info.apple.com/en/ipad_user_guide.pdf
Also, Good Instructions http://www.tcgeeks.com/how-to-use-ipad-2/
Apple - iPad - Guided Tours
http://www.apple.com/ipad/videos/
Watch the videos see all the amazing iPad apps in action. Learn how to use FaceTime, Mail, Safari, Videos, Maps, iBooks, App Store, and more.
How to - Articles & User Guides & Tutorials
http://www.iphone-mac.com/index.php/Index/howto/id/4/type/select
iPad How-Tos http://ipod.about.com/lr/ipad_how-tos/903396/1/
You can download this guide to your iPad.
iPad User Guide for iOS 5
http://itunes.apple.com/us/book/ipad-user-guide-for-ios-5/id470308101?mt=11
 Cheers, Tom

HT1349 i have downloaded itunes on my new laptop , and opened my account but i cant find any of my music stored anywhere , what do i do?

cant access any of my music downloads after accessing my account on a new laptop?where do i find it?

Hi
This forum is for XServes and Servers so your question is not really appropriate. You'd stand more chance of a response if you posted in the correct forum:
https://discussions.apple.com/community/itunes
The main page for all the forums is here:
https://discussions.apple.com/index.jspa
Consult this carefully before deciding which forum is most appropriate for your question.
Have you tried connecting to the Store using the Apple ID you created when purchasing your music? This is not necessarily the same account you use when logging on and using your laptop.
HTH?
Tony

Shortcuts and links fail to work and the message "There was a problem sending the command to the program." appears.

Not long after I upgraded to FF4, my shortcuts and links stopped behaving normally. When I (double) clicked on either I got the message "There was a problem sending the command to the program." This problem doesn't seem to occur with IE9. I am running Windows 7.

In my case, i have solved this by double clicking on the downloaded file directly from the download window

Airobet 1142n erased flash and set baud rate to 115200, cant send any commands

Similar Messages

Maybe you are looking for