Aironet 1010 - AP continues flashing

Guys,
anyone know how to get a AP back online if it continues to flash?
i've tried to reboot the AP - but no luck!!
thanks..

That all depends on the settings
the switchport host command puts the port in access mode only and turns on switchport portfast (hosts should not be negotiating spanningtree anyway!).
most of the time, a cut& paste will work fine, but remember that you will manually have to set your vlan access to match the vlan that the management int on the WLCs reside in.

Similar Messages

  • My 1st Generation time capsule won't connect to the internet thru a new motorola sb6121 - get continuously flashing yellow light. Using a router in between the modem and capsule yields good but slower connection to internet. Any thoughts?

    My 1st Generation time capsule won't connect to the internet thru a new motorola sb6121 - get continuously flashing yellow light. Using a router in between the modem and capsule yields good but slower connection to internet. Any thoughts?

    Thanks for your response
    Let me give the history - I started with an Apple Express being fed thru a D-Link  EBTR 2310 cable Router from an RCA DCM315 Modem (Pure). Comcast service all the way.
    Got the 1st generation TC in 2008 and merely replaced the Airport Express with the TC. Worked ok
    A year or two ago I did try removing the modem and feeding the TC directly from the modem. Resulted in the same condition I have now - Continuous flashing amber on the TC. So I put the router back in the chain.
    Some time later, at the recommendation of a Comcast rep, I replaced the router with (a Belkin F5D 5231) to see if speed and dropout problems would be improved. I thought it helped some at the time but now I am not so sure.
    Last week I decided to see if a new modem would help with download speeds. So I got another pure cable modem (Motorola SB 6121- high on the Comcast recommended list).
    Got up and running easily with Comcast help and with the modem connected directly to a computer.
    Next I put the TC in the link and again could not get past the TC continuing to flash amber. Although I did get connected to the internet with this configuration I lost connection two both of my printers - one connected by USB and the other wirelessly to the TC. Again everything works fine when I put the Belkin router back in the system.
    However with the router in there, the modem shows the downstream connection to be 10/100 ethernet speed. (Modem light changes color for indicating speeds.}
    I have gone thru all of the combinations of powering down/ up, but all stays the same.
    I can live with what I have but something still doesn’t seem right.
    Thanks again

  • Magic Mouse continually flashing light

    We have had our Imac and magic mouse for a fortnight and we are experiencing problems with the Magic mouse!!  It dropped on the floor earlier and the batteries fell out...since putting them back the light on the back is continually flashing and it does not appear to be making any connection to the Mac.  We have tried changing batteries in case, have gone through system preferences etc on the menu and nothing appears to be working.
    Any words of advice would be greatly appreciated.

    You are my hero!!!!
    I have had exactly the same problem with my mouse.  green light underneath the magic mouse double flashing.  No connection to my iMac.
    Took the mouse back to the Apple store and they tested it and swapped for a new one (can't complain about customer service there, very good).
    Still didn't work though when I got back home.
    Just tried what you said, deleted the mouse from the list and re-added it - it works!!
    Thank you.

  • Why does my airport continuously flash amber

    My airport continuously flashes amber and i cant connect to the wifi. how do i fix this?

    There are three Airport resets, soft, hard and factory default.  It would probably be beneficial if you tried each one in sequence.  Actually, you could jump to the factory default reset if you don't mind reconfiguring from scratch.

  • EA6500 - stopped working continuously flashing light

    I have to say that I am greatly disappointed in this wireless router.  This is the second time that this has occurred in less than a year.  The only difference is that the first time (mid May) it corrected by itself.
    Problem:
    The first symptom is that there is a loss of internet connectivity, so we go up and check the router and unplug it.  Initially thinking that there is also a problem with the broadband modem, we poweroff the modem as well. But, recycling the power doesn't resolve the issue.
    We turn everything back on and the router goes through the startup cycle then just goes into a continuous flashing mode. 
    I have attempted to use the reset button to return to reset the configuration, without success.
    I have left it off for long periods of time and then attempted to restart it.
    I have tried turning it on both connected and disconnected from the broadband modem.
    There is now no response from this device. 
    In the past 12 years,  I have owned 2 different dlink wireless routers, and neither failed the entire time that I used them.  The only reason that I swapped them out was for greater functionality and speed improvements. A router that is less than a year old should not go belly up. Cisco should be ashamed to put their name on this device.  I currently manage the global infrastructure for a 1.5 billion Euro company, and we have standardized on Cisco hardware.  This is not even close to the same product quality.
    On an entirely separate soapbox, I object to the fact that the entire configuration and management  is hosted in the internet.  Not very smart, if you loose internet connectivity, you no longer have a LAN.
    Perhaps you can suggest what other alternatives I have besides discarding the device.

    You might need to check if the router was using the correct power adapter. You could also try to reset the router (either the 30-30-30 reset or the 1 minute hardwire) and then power off the router afterwards. In case the router’s power light does continuously blink then, try to follow the steps from this link: http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=a72f05de8a5f4a789db726d535ea68cb_KB__EN_v1.xml&pid... . If in the event that the router’s power light will still be blinking then you might perhaps consider to have the router returned and to have it replaced.

  • WRT54G Router - All lights continuously flashing?

    This morning my WRT54G's lights (link/act, Full/col, 100) were continuously flashing on and off simultaneously and I'd lost all network connectivity.  I've not made any changes (firmware) to the router for about 1 year, and it's been working fine.  I've pulled the plug on the router and when the power's back on, the lights go out but still no connectivity.. after a while all the lights start flashing. I'm just wondering if I need to buy a new one
    Laurent

    Quite right! The old adapter says the output is 5v and I do have another lying around.. my router is up and running   thanks for the tip.
    Laurent

  • E4200 continuous flashing issue: Linksys support, can we get some feedback?

    A few people in the "E-4200 My Review so far - I will answer any questions you have" thread (myself included) are experiencing the continuous flashing of the "Cisco" light on top of the router.  Please see the aforementioned thread for details.
    We've checked the manuals.
    We've talked to tech support.
    We've exchanged routers.
    We've reset the routers dozens of times.
    Nothing seems to work.
    Can we just get some feedback on this?  I'd be glad to provide feedback as to the settings I'm using in order to reproduce this problem, because, well, I can't not reproduce it.
    Even if it can't be fixed right away, I'd just like to know that it's actually being looked at and that it'll probably just be fixed by a future firmware upgrade.  Any feedback would be great!
    Thanks,
    kirkh

    I had the same blinking.  For me it was a neighbors wireless printer that had connected to my network but obviously could not authenticate.  I found it by using the web configuration 'wireless', 'Wireless MAC configuration', and clicking the 'wireless client list'.  From here I could see the offending unit and I blocked it.  Since I did this no more blinking light.  After three days of no blinking, I tested it by allowing the printer access again.  Within minutes, the blinking started.  Againg I configured to block the printer and blinking stopped.
    majorbullet

  • IPod continuously flashes "Do not Disconnect" even when set to automatic.

    iPod continuously flashes "Do not Disconnect" even though iTunes says "Update is Complete" and even when set to automatic update. It mounts both in iTunes and on the Desktop.
    Any suggestions on how to fix this?
    I have alredy tried rebooting both the iPod and computer.
    Thanks.

    Patrick,
    Welcome to the discussions.
    Sounds like you've got Disk Use enabled. Try unchecking the Box "Enable Disk Use" under iTunes>Preferences>iPod Tab.
    JC

  • HP 5610v- Paper out light continually flashing

    My printer has the paper out light continually flashing with plenty of paper still in the tray. If anyone knows a fix please post it or send me an email. My address is [email protected]
    Thanks
    klbilly

    what is the exact error message on the display of the pritner? what happens when you press OK or the Cancel button?
    Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
    Click on the BLUE KUDOS button on the left to say "Thanks"
    I am an ex-HP Employee.

  • Ipod touch is continuously flashing from apple logo to lock screen

    I have a apple ipod touch and it is continuously flashing from the apple logo to the unlock screen.  I can not get it to unlock cause it goes bak and forth. I am in the process of downloading all the updates to itunes so I am hoping that it will somehow fix my issue, but Im doubtful. Has anyone else experienced this and got any advice?  Ive tried restarting it and that doesnt work. I cant turn it off because I cant get the power off slide to come up. Any help would be great.

    - Try:
    iOS: Not responding or does not turn on
    - If not successful and you can't turn the iPod fully off, let the battery fully drain. After charging for at least an hour try the article again.
    - If still problem that indicates a hardware problem and an appointment at the genius Bar of an Apple store is in order.

  • On startup of IE 10 or 11 cursor continually flashes with accompanying circle icon and takes over all machine resources

    Since the last week in November, evertime I start up IE, I get a flashing cursor with rotating blue circle.  If I let it continue for a while - the whole machine becomes un-reponsive.  I tried going back to IE 10 from IE 11 and that did not solve
    the problem.  Any thoughts?

    Hi,
    Does the flashing cursor issue occur in other browser(if you have one)?
    When this issue occurs again, I suggest you run task manager immediately, and view if there is a process takes a high CPU, Memory, etc.
    Sometimes, an anti-virus can cause this issue, I kindly suggest you stop any anti-viruses for a test.
    Or try using process monitor, check if there are some abnormal processes.(close any other programs to reduce the workload)
    http://technet.microsoft.com/en-in/sysinternals/bb896645.aspx
    Regards,
    Yolanda
    Yolanda
    TechNet Community Support

  • Continuous flash playing, regardless of the navigation

    Hi all,
    I'd like to know is it possible to use a swf inside php-/html-pages so that flash is opened and played continuously (not opened again) when user navigates to different pages. So the flash in it should not be reloaded and should just keep on running.
    Is this possible? If not, could you give me suggestion how this could be solved? I don't want to / can not make the whole page with flash, it should only hold a flash animation in one part of it.
    Thanks in advance.

    "Is this possible? If not, could you give me suggestion how this could be solved?"
    Haha..nice going....:)
    Let's just say, is this possible with some technique like fe Ajax?

  • The Time Capsule light continues flashing yellow.

    The machine seems to be working fine with the wifi and backup systems.  I reset the wifi and the light stopped flashing and was green for a couple of hours, but then started again.  Tried a second time with the same outcome.  Any ideas?

    If you have not already done so, you will need to download and install the full featured version of AirPort Utility 5.6 for Mac OS X Lion
    Then open Macintosh HD > Applications > Utilities > AirPort Utility 5.6
    Click Manual Setup
    Click directly on the word Status (2nd line) and a window will open to explain why the Time Capsule is complaining....along with suggestions to remedy the issue. It might be something as simple as a message that an update is available for the Time Capsule.
    Suggest that you keep both AirPort Utility 5.6 and 6.0 on your Mac.  (You cannot delete AirPort Utility 6.0)

  • Can`t make it start, continuously flashing led

    Hi, I have a Power Mac g5 2.0ghz with 4 memory slots. Sudenly I can`t make it start. I get continuosly flashing led without hearing the start bep.
    I try:
    1) changing the ram
    2) changing video card
    3) reset PRAM
    4) reset SMC
    5) cleaning the Ram with rubber
    6) using a hairdryer in the motherboard
    7) disconnecting the CD Player and Hard Drive
    Some times (1 in 20) I can get the machine to start, but when I turn it off it does the same and I get the flashing led.
    Power light status
    What it means
    On and solid
    Computer is on and running
    2 flashes, pause
    No memory (RAM) is installed
    3 flashes, pause
    Incompatible memory (RAM) is installed
    4 flashes, pause
    No good DIMM banks detected
    5 or 6 flashes, pause
    Contact Apple or an Apple Authorized Service Provider
    I should contact a service?????
    Thanks

    I should contact a service?????
    Hello, sadly Apple no longer works on G5s, nor has any parts, you might find an independant AASP that might in your area.
    If you're sure the RAM is good, try the Hair Dryer trick...
    http://discussions.apple.com/message.jspa?messageID=13240047#13240047
    https://discussions.apple.com/message/15223603#15223603
    https://discussions.apple.com/message/15499912#15499912
    https://discussions.apple.com/message/15613068#15613068
    https://discussions.apple.com/thread/3270112
    https://discussions.apple.com/message/16053892#16053892
    No power light at all...
    https://discussions.apple.com/thread/3692775?tstart=0
    It can show on any G5, and even many other computers & electronic devices of the period.
    http://www.macintouch.com/reliability/pmg5.html
    http://lowendmac.com/ppc/power-macintosh-g5.html
    And see this last one in particular...
    https://discussions.apple.com/message/16781690#16781690
    Heat gun better...
    https://discussions.apple.com/thread/3916312?tstart=0

  • Ipod 80GB classic continually flashing apple logo after sync!?!?!?!

    flashing ipod

    Hi Paul,
    Welcome to Apple Support Communities.
    Take a look at the article linked below, it provides the possible resolutions for the issue that you described.
    iPod only shows an Apple logo and doesn't start up
    I hope this helps.
    -Jason

Maybe you are looking for

  • Square Root and Powers Assignement

    Hey guys Ive just started my first year at university, still feeling like ive been thrown in at the deepend. I have a series of assignments to complete for my programming course, and part of one of them is to work out this following: d = (square root

  • Vendor performance analysis report

    Hi all, requirement to create an ALV report for vendor performance analysis...  wat r d tables n feilds which are to be used fr this... any help is appreciated..

  • Many files to one file Processing in XI without using BPM

    Hi XI Experts, Greetings!! I have one requirement in which I have to send three files from ERP system to some Third Party system via XI without using BPM. I seached many threads..but not got the solutions. Please help me. many thanks.

  • Validating  duplicate entries in form level

    Hi I want to validate records whether its duplicate here i am inserting to a table and want to check whether its existing in another table and if not i need to enter the data.I return the following code but its returning error.I already removed the d

  • Commit after 2000 records in update statement but am not using loop

    Hi My oracle version is oracle 9i I need to commit after every 2000 records.Currently am using the below statement without using the loop.how to do this? do i need to use rownum? BEGIN UPDATE (SELECT A.SKU,M.TO_SKU,A.TO_STORE FROM RT_TEMP_IN_CARTON A