Aironet 1130 Configuration

We have a Cisco Aironet 1130AG Access Point in our Community Centre.
It was originally installed by the County Council, with no security password set.
We were unable to access the AP as the technician who installed it had changed the password from the default, but hadn't recorded it (and has now left).
We therefore did a Factory Reset, which has enabled us to configure the AP. However, there are a few problems:
1) If the AP is re-booted, it loses all the settings;
2) We can't save the Current Startup Configuration;
3) We don't seem to be able to change the default password.
Regards
Adrian Cobley

The fact that you can't save the configuration or that it gets deleted after a reboot, points to an issue with the nvram, it might be a hardware failure.
However as George said, paste the configuration to take a look, also issue a show ver and let us know which version are you using.

Similar Messages

  • Cisco aironet 1130 and Intermec CV30

    Hi to all,
    I've a little problem with three Cisco 1130 AP. Anticipately i tell you that i'm not a guru of cisco wireless, but my implementation is very simple. I need a roaming for the 3 AP. I only have Ap, so i configure one as Master Ap and the others like repeater with cisco aironet extension configured. All 3 on the same channel and only the Master one broadcast SSID. Wep security implemented. My Cv30 terminals randomly loose the signal also if they're near an AP. They use windows mobile but i think is only a wrong config problem. I need help. Thank you very much.
    Alex

    The device is using the LWAPP image.. please upgade the same to autonomous image and convert the same..
    Please use the below doc that i hv written and this will helpu!!
    https://supportforums.cisco.com/docs/DOC-14960
    Please dont forget to rate the usefull posts!!
    Regards
    Surendra

  • Cisco Aironet 1130

    I need to configure SNMP on our company Aironet 1130.   I am told there is a tool we can use that will allow us do the configuration from a PC vs connecting directly to the device.. If that is true, where can I download it?

    I would like to enable SNMP on the device so that our SolarWinds Orion NPM server can monitor the device
    Ok.  NOOOOOOOOOOOW I understand you. 
    You need to enable one of two types of SNMP communities:  Read Only or Read-Write.
    For example, if your SNMP community is TV for Read-only and RADIO for Read-Write then it's this:
    snmp-server community TV ro
    snmp-server community RADIO rw

  • Dual SSID (with dual VLAN) on Cisco AiroNet 1130

    Cisco Community,
    I need some major help in figuring out how to change our wireless setup. Currently, we have 2 Cisco AiroNet 1130 WAP's in the office that go directly into the 2 POE ports on our Cisco ASA 5500. These WAP's have 1 SSID and are using WEP for security. After demonstrating the flaws of WEP to my boss, he has agreed that we should use something more secure and I've suggested WPA. We want visitors to our office to be able to hop on our wireless but on a separate guest SSID with WEP.
    I'd like the internal SSID to route to the ASA and take the default route to the internet (it will be our new fiber connection once it's installed in a couple weeks). The default route is whichever connection is working since our ASA 5500 will fail over when it detects an outage.
    I'd like the guest SSID to route to the ASA and then go over our existing cable connection. This connection will be our backup once the fiber connection is installed. Since we won't be using it very often, but will be paying for it, I advised that we send all guest wireless traffic over this connection since 50/5 is plenty for guests.
    I have no idea how to create a VLAN and implement it but I can generally figure things out with a little help. The current SSID (which will be the internal SSID) has no VLAN. We do currently have a few VLANS on our network, one for voice (.42) and one for data (.100) and the default (.0). What device to I create the VLAN on (Cisco 5500?) and how to I setup the WAP? I need very basic instructions to start and I'm also trying to do this without causing downtime if possible.
    I've attached a diagram of what it should look like. Red indicates our internal network and Blue indicates the guest network. I can send screenshots as well.
    Hope everyone is enjoying their holidays.
    Thanks,
    Cody

    Cody,
    Here is a good doc to follow... it explains multiple ssid's and vlans
    https://supportforums.cisco.com/docs/DOC-14496
    Sent from Cisco Technical Support iPad App

  • Aironet 1130 ag not booting

    I have an aironet 1130 ag that won't boot,
    the following is displayed in the console.
    Xmodem file system is available.
    flashfs[0]: 10 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 15998976
    flashfs[0]: Bytes used: 2670592
    flashfs[0]: Bytes available: 13328384
    flashfs[0]: flashfs fsck took 26 seconds.
    Base ethernet MAC Address: 00:1c:58:06:a1:1a
    Initializing ethernet port 0...
    Reset ethernet port 0...
    it freezes at the above point
    I tried holding down the mode button to transfer a new image via tftp but that failed (the link b/w the ap and the computer never came up)
    It seems the the ap can't bring the ethernet interface up.  Is this a hardware problem or is there something else i should try?

    I would think about an RMA at this point.
    Nicolas

  • Aironet 1130 AG series Browser configuration Service Tab display issue

    Has anyone ran into an issue accesing the service tab to display the service summary page? I ran into this issue while configuring the wap through the browser when suddenly the service tab will not display the services summary page.
    System Software Version: 12.4(10b)JA

    Here are 2 responses from Cisco:
    1.Hi Carlo,
    I came to know that the fix for the bug CSCsl22021 should be available from the Cisco website, this month, ie, in March. However, as indicated earlier, the fix is in the testing phase, as of now.
    Thanks for your time and support,
    We do value your business.
    Rajan Parmar
    Cisco TAC Engineer - Wireless
    Cisco Systems Inc.
    [email protected]
    1-212-329-2092 Ext-2060
    Monday to Friday 08:00 AM to 5:00 PM (EST)
    2.Hi Carlo,
    Thank you for the update.
    I researched on the issue and got the following details:
    Our case is being hit by a bug. For the details, please visit http://tools.cisco.com/Support/BugToolKit and enter the bug id as CSCsl22021.
    As of now, its the test code that is available as the fix, and it requires additional testing on it. If you wish, we can send you the test code, however, we cannot provide guarantee for it work without any flaws in the production environment. Otherwise, you may downgrade the existing IOS by downloading code from http://tinyurl.com/yqc4sx. You may downgrade to 12.3.8-JEA3(LD).
    Please feel free to contact me for any clarification.
    Thanks for your time and support,
    We do value your business.
    Rajan Parmar
    Cisco TAC Engineer - Wireless
    Cisco Systems Inc.
    [email protected]
    1-212-329-2092 Ext-2060
    Monday to Friday 08:00 AM to 5:00 PM (EST)
    Carlo..

  • Aironet 350 configuration to Aironet 1300

    Is it possible to download an ini configuration from an Aironet 350 bridge, convert it and upload it to an Aironet 1300 bridge?

    Nevermind...I found it http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/s12213JA.html#wp55027

  • Aironet 1250 Configuration Help

    Hello to all,
    I'm an  vmware\linux system administrator with very low skills in networking, I just bought 3 Cisco Aironet 1250 2.4ghz + 5ghz for my testing network and I need help to configure them.
    Scenario:
    1 - I have 3 Cisco Aironet 1250
    2 - I want to create 2 wifi networks, SSID guest (vlan 11) and SSID production (vlan 1) in 2.4ghz + 5ghz
    2a- I want to configure security WPA2-PSK without RADIUS Server.
    3 - Aironet 1250 # 1 is connected to ethernet vlan1 (production)
    4 - Aironet 1250 # 2 is connected to ethernet vlan11 (guest)
    5 - Aironet 1250 # 3 is connected to ethernet vlan1 (production)
    These are the first configuration commands found:
    configureno ip domain-lookupline vty 0 4no exec-timeoutenableconfigure terminalinterface dot11radio 0encryption vlan 1 mode ciphers aes-ccmssid Productionvlan 1authentication openauthentication key-management wpa version 2wpa-psk ascii password1guest-modeend        interface dot11radio 1encryption vlan 11 mode ciphers aes-ccmssid Guestvlan 11authentication openauthentication key-management wpa version 2wpa-psk ascii password2guest-modeend
    When I try to set the repeater configuration webinterface tells me configuration errors.
    Any help is welcome, sorry for my newbie!
    Thanks a lot!

    Since each AP is connected via Ethernet, you don't need to set any as a repeater. Here are some links that show you what you need to have multiple SSID's and multiple vlans.
    http://www.cisco.com/en/US/docs/wireless/access_point/12.2_11_JA/configuration/guide/s11ssid.html
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a0080665ceb.shtml
    Tech Guides
    http://www.cisco.com/en/US/products/hw/wireless/ps4570/prod_configuration_examples_list.html
    Sent from Cisco Technical Support iPhone App

  • Difference between aironet 1130 and 1230

    can you please tell me what are the differences between this 2 Aironet?
    regards

    Here is the data sheets,
    1230
    http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps6108/product_data_sheet0900aecd801b9068.html
    1130
    http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps6087/product_data_sheet0900aecd801b9058.html
    Regards,
    ~JG
    Do rate helpful posts

  • Manage new Aironet 1130 with web browser

    Hello,
    I bought a wi-fi Aironet 1130AG, I plug it in my network, it gets an IP address with my DHCP server but I can not manage it with my internet browser, "Internet Explorer can not display this page ". Wifi terminal responds to ping.
    Thank you for your help.
    Anthony

    When you recieve brand new AP you should be able to console into it.
    Just to evaluate what you really have we need to have console output :
    May be the IOS image is corrupted for example.
    If after checking the console and making sure that nothing wrong , i would say re-image the AP using console session.
    check the following link for more information on how to download ios image to the AP:
    http://www.cisco.com/en/US/partner/docs/wireless/access_point/12.4_10b_JA/configuration/guide/scg12410b-chap20-firmware.html#wp1035644
    Please Don't forget to rate correct answers

  • Copying Aironet IOS configuration

    I set up one AP-1041 that runs standalone IOS. No controller. I have three more that I want to copy the setup configuration over to. I have the right document, but need someone to help tell me which commands will get my set configuration from AP one FTP'd to my computer and how to copy that configuration back to another AP of the same model. This way I will only need to tweak a couple settings on the additional AP's instead of starting from scratch.
    Thanks in advance,
    Kirk
    What I'm referencing starts in about section 20-10
    http://www.cisco.com/en/US/docs/wireless/access_point/12.4_10b_JA/configuration/guide/scg12410b.pdf

    Hi Kirk,
    To copy the configuration from AP to PC you could run below command. My preference would be to use tftp rather than tftp.
    copy system:running-config tftp://x.x.x.x/ap.txt or copy running-config tftp://x.x.x.x/ap.txt
    (where x.x.x.x is the ip address of tftp server and ap.txt is configuration file name)
    Top copy from PC to AP you could use below command.
    copy tftp://x.x.x.x/AP.txt startup-config (where x.x.x.x is the ip address of tftp server and ap.txt is configuration file name)
    Ensure that you are able to ping the tftp ip address from the AP before trying the copy procedure.
    Hope that helps.
    Regards
    Najaf
    Please rate when applicable or helpful !!!

  • Aironet 1130 AG Ping Drops.

    Hello Friends,
    We have 5 Access point in our network. recently we discovered ping drops in all access point. the pings dropping randomly. sometime one request time out or three times.
    All APs are connected with POE edge switch.For test,  we attached with other Core switch with power adapter but again same problem. We created different VLan & tried but same result.Even we upgraded OS to 12.4(25d)JA2
    We tested same AP with other company network & there its working without any drops.
    We are facing this issue since one month & there is no changes in network configuration.
    Please advice on this problem.
    Thank You..

    We tested same AP with other company network & there its working without any drops.
    So when you say this, to me it's no change in the AP configuration, but your just connecting it to another network and it's working fine. So that being said, looks like a meteors configuration issue not an issue.  
    -Scott

  • Aironet 1130 AG Series

    I am in the process of setting up a free wireless network for visitors and tenants to use in their free time. I have run into a problem with a tenant wanting to keep their employees off the network by issuing a password. I would like to avoid this if at all possible by simply blocking their work computers Mac Addresses from accessing the network. Can this be done via the control pages as I know nothing about CLI? If so where do I start?
    Much thanks for any help I can get on this.

    Configuring Filters
    http://www.cisco.com/en/US/docs/wireless/access_point/12.4_10b_JA/configuration/guide/scg12410b-chap16-filters.html
    Please don't forget to rate my post.  Thanks.

  • CT2504 and Aironet 1142N configurations

    Hi All,
    I have bought 2504 LAN Controller and my old 1142 wants to configure to accept that Controller instead of old controller. These APs and controllers in far away site and before I go there I want to figure out how can I do followings. Your help much more appreciated, Because Lack of my knowledge and experience in wireless.
    1.   How can I configure old 1142(Previously connected with another LAN Controller) to accept New 2504 Controller instead of old controller ?
    2.  What are the concerns do I need to consider?
    3.  Is there any configuration example which can be understand easier to a beginner?  or any guide to guide me without much hassel?
    Thanking you in advance
    Chamara

    A unified access point or a LAP would only keep the management address of all the wlc it has discovered previously by joining them, or though mobility configuration on them (mobility members on them).
    As far as configuration is concerned, each time an lap joins a new or for that matter the same wlc it has previously joined,
    it pulls the configuration/revision to it as an event/state as defined for CAPWAP state machine.
    Here is the CAPWAP state machine for your reference,
                                |          /-------------------------\|
                                |         p|                         ||
                                |    q+----------+ r +------------+  ||
                                |     |   Run    |-->|   Reset    |-\||
                                |     +----------+   +------------+ |||
                               n|  o      ^           ^     ^      s|||
                    +------------+--------/           |     |       |||
                    | Data Check |             /-------/    |       |||
                    +------------+<-------\   |             |       |||
                                          |   |             |       |||
                           /------------------+--------\    |       |||
                          f|             m|  h|    j   v   k|       |||
                   +--------+     +-----------+     +--------------+|||
                   |  Join  |---->| Configure |     |  Image Data  ||||
                   +--------+  n  +-----------+     +--------------+|||
                    ^   |g                 i|                    l| |||
                    |   |                   \-------------------\ | |||
                    |   \--------------------------------------\| | |||
                    \------------------------\                 || | |||
             /--------------<----------------+---------------\ || | |||
             | /------------<----------------+-------------\ | || | |||
             | |  4                          |d           t| | vv v vvv
             | |   +----------------+   +--------------+   +-----------+
             | |   |   DTLS Setup   |   | DTLS Connect |-->|  DTLS TD  |
           /-|-|---+----------------+   +--------------+ e +-----------+
           | | |    |$  ^  ^   |5  ^6         ^              ^  |w
           v v v    |   |  |   |   \-------\  |              |  |
           | | |    |   |  |   \---------\ |  |  /-----------/  |
           | | |    |   |  \--\          | |  |  |              |
           | | |    |   |     |          | |  |  |              |
           | | |    v  3|  1  |%     #   v |  |a |b             v
           | | \->+------+-->+------+   +-----------+    +--------+
           | |    | Idle |   | Disc |   | Authorize |    |  Dead  |
           | |    +------+<--+------+   +-----------+    +--------+
           | |     ^   0^  2      |!
           | |     |    |         |   +-------+
          *| |u    |    \---------+---| Start |
           | |     |@             |   +-------+
           | \->+---------+<------/
           \--->| Sulking |
                +---------+&
    Regards
    Sahil

  • Aironet 1130 AG

    I am configuring the Access Point and after going through the Express Setup and Express Security pages, and after turning the radios on, the Services page no longer displays HTTP, or any other services. It does however display the following...
    " \n'; for (i=0; i "
    and that is all.
    Any ideas what has happened? I am configuring two of these and each one does this same thing, so I do not believe it to be a hardware error.

    The Bootloader version is 12.3(8)JEA.... It seems that when I go to Security-->Admin Access and change the Authentication to "Local User List Only" and then remove the Global Password, the Services page disappears. Unless someone has something better, I think that I will keep a Global Password, but change it. That seems to have worked....

Maybe you are looking for