Aironet 1140 connection and log questions
Hi Cisco gurus,
Recently we decided to change the name of one of our Aironet 1140 AP's. Everything was great for a few days then, for some reason, nobody was able to connect to it. They would all recieve timeout messages when they would connect. A quick reset solved the problem, but I'm curious if there was an actual reason to why it didn't allow users to connect in case it happens again.
Which brings me to my next question, how do you set the AP clock so that the event logs display the proper date and time? I'm sure I overlooked something, but I can't find out how to set the proper date and time.
Thank you in advance.
conf t
serv time d d s l
serv time l d s l
sntp service
! Set the timezone
clock timezone WORD
clock summer-time WORD recurring
Similar Messages
-
After installing Yosmite, The following message is stopping me accessing my disk utility. 'You can't use this version of the application “Disk Utility” with this version of OS X.' you have “Disk Utility” 12.1.1.
not only that my Mac pro keeps dropping my internet connection and logs on to BT Open.
HelpFor whatever reason you don't have the Yosemite version of Disk Utility which is 13. I suggest you reinstall Yosemite.
Reinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Download and install the 10.10.1 update.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Check that you have the current version of Disk Utility. -
Music streams but no internet connectivity and a question about a poss. fix
Forgive me if this question has been answered already (searched the forums for two hours and found none that were answered). Where I work there are two wireless networks, set up completely separate from one another using Linksys WRT54G routers. I've set up my Express to join one of the networks, (let's call it Network "A"). I chose this one because it's closer, signal is stronger and when I tried Network "B", streamed music would crackle out regularly.
Lately though I find that my internet connectivity disappears on Network "A" while music continues to stream flawlessly (airport signal shows full strength). I reset the Express, restart my computer, nothing seems to fix it outside of leaving for the night and coming back the next day. I switch to the other network, no problems with the internet, but streaming music becomes problematic. So here are my questions:
1. Anyone have advice on how I can fix the internet connectivity problem on Network "A"?
2. Failing that, does anyone know if it's possible to set up my express in such a way where it's only being used for streaming music (without joining or extending a wireless network) and then also connect my computer via wireless to either network for internet access? Wired access is not an option here unfortunately...
Again, sorry if this question has been answered somewhere else.
Message was edited by: Clavin
Message was edited by: Clavin1. Anyone have advice on how I can fix the internet connectivity problem on Network "A"?
When joining an existing network with the AirPort Express Base Station (AX), the AX is acting no different than you laptop connecting to that same wireless network. If there is connectivity problems with this network, both the AX and your laptop should "see" the same problems.
It is very possible that you may have some form of Wi-Fi interference in the immediate area that is preventing your Mac from getting a good clean signal from the Linksys router.
I suggest you perform a simple site survey, using utilities like MacStumbler or iStumbler to determine potential areas of interference, and then, try to either eliminate or significantly reduce them where possible.
2. Failing that, does anyone know if it's possible to set up my express in such a way where it's only being used for streaming music (without joining or extending a wireless network) and then also connect my computer via wireless to either network for internet access? Wired access is not an option here unfortunately...
The only other option would be to configure the AX to be its own wireless network. The disadvantage of this would be that you would have to "switch" wireless networks in order to either stream audio or access the Internet. -
HP C4480 to Mac adaptor/connection and other questions!
I have a macbook, airport router and HP C4480 printer.
2 Questions.
First what is the cord I need to connect the printer to the computer and/or airport?
Second, can I connect the printer wirelessly? If so, HOW?
Thanks,
StefanieHello Stefanie,
You'll most likely need to purchase a USB printer cable. These can be found at most electronic & office supply stores (Best Buy, Staples, Office Depot, etc...) or online: http://www.mptools.com/usbprinter_cables.htm?gclid=CJeHZza3KECFUNb2godrGH3Ig
http://www.amazon.com/Belkin-F3U133-10-Hi-Speed-Cable-Feet/dp/B00004Z5M1
To connect the printer via wireless, check out:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00710847&tmp_task=useCatego ry&lc=en&dlc=en&cc=us&product=3418705
Hope this helps... -
I started a movie download go interrupted and now cannot resume. How do I restart a paid for movie.
Launch iTunes Store app.
Tap on "Purchases" tab. (This assumes you've already logged in to your iTunes account.)
Tap on "Movies" tab at the top, center of the screen.
Optionally tap on "Not on This iPad" tab.
Tap the "Download from iCloud" icon (downward-pointing arrow coming out of cloud icon). -
Cannot get Windows 7 x64 laptop to connect to AIRONET 1140 WAP
I recently changed the configuration of my Aironet 1140 from WEP to WAP2-Enterprise to make it more secure. I am using the WAP as the radius server. After making the change I connected my Blackberry to the wap as well as a Samsung Chromebook. However when I tried to connect my HP laptop it is unable to connect. Watching from the Aironet's console I see that it is processing the association and windows ask me to enter my uid and password. When I do this I get an authentication error. I have tried several times adjusting parameters on windows but it always fails. Here is the configuration of the WAP:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap.acrtek-lab.com
logging rate-limit console 9
aaa new-model
aaa group server radius rad_eap
server 10.53.55.127 auth-port 1812 acct-port 1813
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login default local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
dot11 syslog
dot11 ssid Acrtek-WPA2
authentication open eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa
username XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
username XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
ssid Acrtek-WPA2
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption mode ciphers aes-ccm tkip
ssid Acrtek-WPA2
antenna gain 0
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server local
no authentication eapfast
no authentication mac
nas 10.53.55.127 key 7 xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
user xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
radius-server attribute 32 include-in-access-req format %h
radius-server host 10.53.55.127 auth-port 1812 acct-port 1813 key 7 xxxxxxxxxxxxxxxxxxxxxxxxxxxx
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 0 4
end
Windows Configuration:
Details about network adapter diagnosis:
Network adapter Wireless Network Connection driver information:
Description . . . . . . . . . . : Broadcom 4313GN 802.11b/g/n 1x1 Wi-Fi Adapter
Manufacturer . . . . . . . . . : Broadcom
Provider . . . . . . . . . . . : Broadcom
Version . . . . . . . . . . . : 5.100.82.139
Inf File Name . . . . . . . . . : C:\Windows\INF\oem29.inf
Inf File Date . . . . . . . . . : Tuesday, September 18, 2012 5:42:34 PM
Section Name . . . . . . . . . : BCM43XNG2022_NT61
Hardware ID . . . . . . . . . . : pci\ven_14e4&dev_4727&subsys_1795103c
Instance Status Flags . . . . . : 0x180200a
Device Manager Status Code . . : 0
IfType . . . . . . . . . . . . : 71
Physical Media Type . . . . . . : 9
Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
Information for connection being diagnosed
Interface GUID: 5bab8bfe-12d7-4e0c-a46b-efc490047802
Interface name: Broadcom 4313GN 802.11b/g/n 1x1 Wi-Fi Adapter
Interface type: Native WiFi
Profile: Acrtek-WPA2
SSID: Acrtek-WPA2
SSID length: 11
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Connection incident diagnosed
Auto Configuration ID: 2
Connection ID: 3
Connection status summary
Connection started at: 2012-09-18 14:49:56-586
Profile match: Success
Pre-Association: Success
Association: Success
Security and Authentication: Fail
List of visible access point(s): 43 item(s) total, 43 item(s) displayed
BSSID BSS Type PHY Signal(dB) Chnl/freq SSID
00-1C-10-07-38-76 Infra <unknown> -79 11 linksys
70-56-81-CB-A2-7D Infra <unknown> -55 10 MRB LLC
08-86-3B-95-3B-E1 Infra <unknown> -77 11 belkin.be1
C0-C1-C0-52-FD-5F Infra <unknown> -75 11 AquaDeer-guest
70-73-CB-BB-9D-43 Infra <unknown> -60 1 the ridge by apple
00-17-C5-A5-5A-73 Infra <unknown> -67 2 MsPub
00-22-B0-BA-C7-E6 Infra g -72 1 mercer
E0-91-F5-D6-DF-76 Infra <unknown> -78 1 Chick-Fil-A
04-C5-A4-80-FC-50 Infra <unknown> -38 4 (Unnamed Network)
C8-3A-35-5D-AE-18 Infra <unknown> -82 4 medialink
00-23-69-1B-73-C9 Infra g -78 6 Matt and Heather
94-44-52-68-24-2B Infra <unknown> -73 5 Belkin.442B
68-7F-74-7E-50-74 Infra g -77 6 sjslinksys
00-1D-7E-49-E2-65 Infra g -75 6 Cubs
00-12-17-4B-4E-0D Infra g -41 8 (Unnamed Network)
C0-C1-C0-E4-3F-55 Infra <unknown> -78 6 SG Roi
C0-C1-C0-66-9F-CA Infra <unknown> -75 7 Heliman
66-33-4B-E1-47-27 Infra <unknown> -80 8 Jenny lake's Guest Network
00-1C-DF-A4-59-FB Infra <unknown> -60 10 radiofinger
C0-C1-C0-52-FD-5E Infra <unknown> -76 11 AquaDeer
08-86-3B-61-B0-BC Infra <unknown> -76 11 belkin.0bc
00-23-69-00-52-20 Infra g -70 11 670term
58-6D-8F-24-FC-21 Infra <unknown> -80 11 Bluejay1
04-C5-A4-80-FC-50 Infra <unknown> -36 4 Acrtek-WPA2
70-73-CB-BB-B3-49 Infra <unknown> -73 1 LeWonderment Inc.
E6-51-E4-A6-B1-25 Ad hoc g -78 4 megahoc.v24
00-17-C5-A5-5A-A9 Infra <unknown> -79 5 Vivaces
00-23-69-B4-5D-3E Infra g -81 6 Tanda
D0-66-7B-06-C7-45 Infra <unknown> -81 7 SEC_LinkShare_e70ac7
00-24-7B-5D-65-FA Infra g -80 6 myqwest0953
60-33-4B-E1-47-27 Infra <unknown> -81 8 Jenny Lake
00-25-9C-23-73-A6 Infra g -80 1 milehigh
00-24-01-DC-A4-3F Infra <unknown> -81 3 newwoman
C4-3D-C7-83-CE-74 Infra <unknown> -85 3 Desilets
08-86-3B-25-A7-CE Infra <unknown> -86 11 belkin.7ce
00-18-39-78-8F-92 Infra g -88 11 paul landow
98-FC-11-6E-E7-52 Infra <unknown> -80 11 China
28-CF-DA-B1-5F-03 Infra <unknown> -78 1 DeSanti
00-15-6D-D6-04-47 Infra g -69 1 (Unnamed Network)
00-21-91-10-1A-05 Infra g -81 1 dlink
1C-7E-E5-30-AE-66 Infra <unknown> -79 5 dlink
00-15-FF-26-47-98 Infra <unknown> -85 10 Verizon MIFI4510L 4798 Secure
00-23-69-38-2C-D2 Infra <unknown> -82 1 linksys
Connection History
Information for Auto Configuration ID 3
List of visible networks: 41 item(s) total, 41 item(s) displayed
BSS Type PHY Security Signal(RSSI) Compatible SSID
Infra <unknown> No 22 Yes linksys
Infra <unknown> Yes 82 Yes MRB LLC
Infra <unknown> Yes 26 Yes belkin.be1
Infra <unknown> No 30 Yes AquaDeer-guest
Infra <unknown> Yes 76 Yes the ridge by apple
Infra <unknown> No 62 Yes MsPub
Infra g Yes 36 Yes mercer
Infra <unknown> Yes 24 Yes Chick-Fil-A
Infra <unknown> Yes 94 Yes (Unnamed Network)
Infra <unknown> Yes 16 Yes medialink
Infra g Yes 24 Yes Matt and Heather
Infra <unknown> Yes 34 Yes Belkin.442B
Infra g Yes 26 Yes sjslinksys
Infra g Yes 30 Yes Cubs
Infra g Yes 92 Yes (Unnamed Network)
Infra <unknown> Yes 24 Yes SG Roi
Infra <unknown> Yes 30 Yes Heliman
Infra <unknown> Yes 20 Yes Jenny lake's Guest Network
Infra <unknown> Yes 76 Yes radiofinger
Infra <unknown> Yes 28 Yes AquaDeer
Infra <unknown> Yes 28 Yes belkin.0bc
Infra g Yes 40 Yes 670term
Infra <unknown> Yes 20 Yes Bluejay1
Infra <unknown> Yes 95 Yes Acrtek-WPA2
Infra <unknown> Yes 34 Yes LeWonderment Inc.
Ad hoc g No 24 Yes megahoc.v24
Infra <unknown> No 22 Yes Vivaces
Infra g Yes 18 Yes Tanda
Infra <unknown> Yes 18 Yes SEC_LinkShare_e70ac7
Infra g Yes 20 Yes myqwest0953
Infra <unknown> Yes 18 Yes Jenny Lake
Infra g Yes 20 Yes milehigh
Infra <unknown> Yes 18 Yes newwoman
Infra <unknown> Yes 10 Yes Desilets
Infra <unknown> Yes 8 Yes belkin.7ce
Infra g Yes 4 Yes paul landow
Infra <unknown> Yes 20 Yes China
Infra <unknown> Yes 24 Yes DeSanti
Infra g No 50 Yes (Unnamed Network)
Infra g No 22 Yes dlink
Infra <unknown> Yes 10 Yes Verizon MIFI4510L 4798 Secure
List of preferred networks: 5 item(s)
Profile: Acrtek-WPA2
SSID: Acrtek-WPA2
SSID length: 11
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: Yes
Profile: ZRDD2
SSID: ZRDD2
SSID length: 5
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: No
Reason: 0x00028002
Profile: GMANNET
SSID: GMANNET
SSID length: 7
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: No
Reason: 0x00028002
Profile: Conference Rm
SSID: Conference Rm
SSID length: 13
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: No
Reason: 0x00028002
Profile: rntdnet
SSID: rntdnet
SSID length: 7
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: No
Reason: 0x00028002
Information for Connection ID 4
Connection started at: 2012-09-18 14:50:08-279
Auto Configuration ID: 3
Profile: Acrtek-WPA2
SSID: Acrtek-WPA2
SSID length: 11
Connection mode: Infra
Security: Yes
Pre-Association and Association
Connectivity settings provided by hardware manufacturer (IHV): Yes
Security settings provided by hardware manufacturer (IHV): No
Profile matches network requirements: Success
Pre-association status: Success
Association status: Success
Last AP: 04-c5-a4-80-fc-50
Security and Authentication
Configured security type: WPA2-802.1X
Configured encryption type: CCMP(AES)
802.1X protocol: Yes
Authentication mode: Invalid (5)
Number of 802.1X restarts: 1
Number of 802.1X failures: 0
Key exchange initiated: No
Number of security packets received: 2
Number of security packets sent: 1
Security attempt status: Success
Information for Auto Configuration ID 2
List of visible networks: 40 item(s) total, 40 item(s) displayed
BSS Type PHY Security Signal(RSSI) Compatible SSID
Infra <unknown> No 22 Yes linksys
Infra <unknown> Yes 85 Yes MRB LLC
Infra <unknown> Yes 22 Yes belkin.be1
Infra <unknown> No 32 Yes AquaDeer-guest
Infra <unknown> Yes 64 Yes the ridge by apple
Infra <unknown> No 74 Yes MsPub
Infra g Yes 60 Yes mercer
Infra <unknown> Yes 24 Yes Chick-Fil-A
Infra <unknown> Yes 86 Yes (Unnamed Network)
Infra <unknown> Yes 38 Yes medialink
Infra g Yes 36 Yes Matt and Heather
Infra <unknown> Yes 40 Yes Belkin.442B
Infra g Yes 62 Yes sjslinksys
Infra g Yes 30 Yes Cubs
Infra g Yes 95 Yes (Unnamed Network)
Infra <unknown> Yes 24 Yes SG Roi
Infra <unknown> Yes 28 Yes Heliman
Infra <unknown> Yes 20 Yes Jenny lake's Guest Network
Infra <unknown> Yes 81 Yes radiofinger
Infra <unknown> Yes 10 Yes AquaDeer
Infra <unknown> Yes 32
Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
For complete information about this session see the wireless connectivity information event.
Helper Class: Auto Configuration
Initialize status: Success
Information for connection being diagnosed
Interface GUID: 5bab8bfe-12d7-4e0c-a46b-efc490047802
Interface name: Broadcom 4313GN 802.11b/g/n 1x1 Wi-Fi Adapter
Interface type: Native WiFi
Profile: Acrtek-WPA2
SSID: Acrtek-WPA2
SSID length: 11
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Result of diagnosis: Problem found
Issue referred to: L2Sec Helper Class
Root cause:
Windows could not connect to "Acrtek-WPA2"
You can try to connect again.
Repair option:
Reset your wireless network adapter
This will disable and then enable the network adapter "Wireless Network Connection" on this computer.
Diagnostics Information (L2sec Helper Class)
Details about L2Sec Helper Class diagnosis:
For complete information about this session see the Wireless Diagnostic Informational Event.
Helper Class: Layer2 Security
Initialize Status: Success
Result of diagnosis: Problem found
Issue referred to: EAP Helper Class
Root cause (EAP):
Network authentication failed\nWindows doesn't have the required authentication method to connect to this network.
Detailed root cause:
EAP failed
Workaround for hypothesis: Contact the network administrator for "Acrtek-WPA2"
EAP workaround: Contact your network administrator\nWindows needs to be configured to use the authentication method required for this network.
Information for connection being diagnosed
Interface GUID: {5bab8bfe-12d7-4e0c-a46b-efc490047802}
Interface name: Broadcom 4313GN 802.11b/g/n 1x1 Wi-Fi Adapter
Interface type: Native WiFi
Profile: Acrtek-WPA2
SSID: Acrtek-WPA2
SSID length: 11
Connection mode: Infra
Security enabled: Yes
Connection ID: 3
Security settings provided by hardware manufacturer (IHV): No
Profile matches network requirements: Yes
Pre-Association and association status: Success
Security and Authentication:
Configured security type: Robust Secure Network (RSN / WPA2) with 802.1X
Configured Encryption type: CCMP (AES)
Security connect status: Fail 0x00050005
Number of security packets received: 4
Number of security packets sent: 3
802.1X protocol: Yes
Authentication Identity: User only
IAS Server engaged: Yes
EAP Method supported by IAS Server: Unknown
EAP type: 25
EAP Error: 0x40420016
Number of 802.1X restarts: 1
Number of 802.1X failures: 1
802.1X status: Fail 0x00050005
Key exchange initiated: No
Unicast keys received: No
Multicast keys received: No
Network Diagnostics Log
File Name: A20D3467-8AD4-483E-91F4-9EC5E18AA1F9.Diagnose.0.etl
Other Networking Configuration and Logs
File Name: NetworkConfiguration.cab
Collection information
Computer Name: ACCRETIVE-SW
Windows Version: 6.1
Architecture: amd64
Time: Tuesday, September 18, 2012 2:50:09 PM
Any help would be greatly appreciated.Hello Mr. Wells,
Thank you for your question.
However, the Small Business Support Community is limited to Cisco Small Business Products, and the Aironet products are considered as a Enterprise level devices.
I recommend you to post this question on the on the correct forum, in order to get a better response.
You can move your post using the Actions panel on the right.
Best regards,
Diego Rodriguez
Cisco Small Business Community Engineer -
Configuring Cisco Aironet 1140 for Radius and setting up a Radius server
guys i need some help setting up my Radius to work with cisco aironet 1140, i am new at this however i was tasked with setting up a Radius server and setting our AP with WPA2- enterprise so users can log into our AP using AD credentials.
When i try to setup on the AP a new SSID i do not see the option for WPA2- enterprise?Here are other links with examples:
https://supportforums.cisco.com/thread/331581
http://targetcisco.blogspot.com/2011/03/cisco-autonomous-access-point.html
http://downloads.avaya.com/css/P8/documents/100041614
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Connected clients on Aironet 1140
I've been using Aironet 1140 series access point for a while. Recently it started to drop the wireless clients quite often. we have nearly 20 wireless users and one access point. they are mix of apple macs, windows and mobile phone users. when i went in to see the connected clients all the clients whown on the web page are connected through cable to our LAN. whay is it showing as connected to dot11 radio? am i missing something here? thanks
Can you post a screen shot? You sure the devices on your lan doesn't ahve a wireless card?
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Android 4.1 tablet not connecting to Aironet 1140
Hello community, I am having an issue with my Android Tablet running 4.1 (Jelly Bean). It is able to the SSID, but when I try to connect - it stays connecting and then says saved, and never connects, as it does not pick up an IP address. I updated the firmware on the Aironet 1140 due to my Windows 8 pc's not connecting as well, it solved my Windows 8 problem, just not my Android Tablet problem. My Ipads do work. Just any android device I connect...
Anyone, ran into this issue that can assist?
Thanks in advance.Hello William,
What is the security used on your wireless LAN?
Can you apply this command on your WLC CLI:
show wlan
and post us the output right here?
Reards,
Amjad
Rating useful replies is more useful than saying "Thank you" -
Exchange 2007 account - trouble connecting at times and a question
Hi all, so, I have my Ex change 2007 account setup on my MacBook Pro but I seem to keep having an issue. WHen the account was initially setup, I was connected to my company via the Cisco VPNClient and the connection worked great - mail, iCal & AddressBook all connected and accessed data fine.
Now, I find that if I drop my VPN and then reconnect, Mail will not connect to the server and I get the Yield or tilde icon next to the account. In console, I'm getting these messages:
9/1/09 9:21:49 AM Mail[1349] -[SOAPParser:0x1163a34e0 parser:didStartElement:namespaceURI:qualifiedName:attributes:] Type not found in SOAPDocument for HTML (HTML)
Now, it seems that if I disconnect the VPN, quit Mail and leave it for a while (sorry, nothing scientific here yet) it will reconnect to the server after I have the VPN back up.
One point to make, I can't seem to get the Apple IPSec support to connect to my company's Cisco concentrator, hence the reason I keep using the Cisco sw.
So, that's my one problem - now for the additional questions: Is the Exchange support in SL Exchange Activesync or a different implementation? The reason I ask is that if it's exchange Activesync, there should be no reason I cannot connect to my Exchange front-end server without a vpn connection and sync mail, calendar & addressbook - right?
That doesn't seem to work, however which leads me to think it's not EAS.
Another question - is there any documentation on how to configure the advanced mail account options - External Server Path, for instance?
Thanks in advance...
DaveI had the exact same issue. Found nothing in the console logs other than "can't refresh account". Turns out my problem was wrong e-mail address with the exchange server. I used the exact e-mail address that this particular exchange expected and it added it to the panel on the left.
Our setup is a bit weird cause we have 2 exchange servers, but I let iCal figure out everything itself using the "old" exchange server and then afterwards went and edited the server settings to use the "new" server, and it kept working with these settings.
Just a bit annoying that iCal was so vague about what the problem was... Also didn't help that I upgraded and moved to the "new" server and changed my password all at once, so don't know what cause the problem in the first place. -
I have bought a WD My Book World Edition to use for back-up of my iMac, but when I try and log onto the drive with Apple time Machine (back-up software) or connect in any other way I get the message 'There was a problem connecting to the server "MybookWorld.local" The version of the server you are trying to connect to is not supported. Please contact your system administrator to resolve the problem'
It is a brand new iMac and running Lion OSX
Any ideas on how to solve would be gratefully received?Followed the directions on this page and it worked!
http://forums.macrumors.com/showthread.php?t=1102423
Part One - Turn on SSH (in the admin panel)
[1] Go to to http://mybookworld.local
[2] login: username will be admin, password will be whatever you have setup. If you can't remember it should be in your Mac OS X keychain (Utilities > Keychain Access, search for "mybookworld"). If you have not changed if from the default the password will be admin as well.
[3] Switch to advanced mode.
[4] From the System tab, pick Advanced.
[5] Enable SSH Access, and click submit.
[6] Click on the network tab and then the LAN button
[7] Make a note of the IP address
Small, maybe obvious, but nevertheless important point: For the install to work, your NAS needs to be connected to a router with internet access.
Part Two - Install netatalk2.2
[8] Open Terminal.app (Utilities > Terminal)
[9] Enter the following command (substitute in 127.0.0.1 for the actual IP address you noted down in step 7), then hit return:
Code:
ssh [email protected]
[10] When prompted, enter the ssh password (will be welc0me).
[11] You are now going to download the installer. Enter the following command, then hit return:
Code:
wget http://mybookworld.wikidot.com/local--files/netatalk2-2-on-whitelight/install_netatalk.sh -O install_netatalk.sh
[12] Once completed, you will need to run the installer. Type:
Code:
sh install_netatalk.sh
[13] You will be asked a number of question during install, answer yes to all. When asked about the "DHX2 login process", I opted to install the modified version, so I can confirm it works.
[14] Once the box has restarted, you should be able to connect to your afp shares and continue to use Time Machine. -
Aironet 1140 54Mbps connection speed
We are having some issues with our AP: Aironet 1140 at our head office where people are complaining of slow connection speeds.
I have gone through the configuration on the controller and noticed that all Clients were connecting at 802.11g connection speeds (54Mbps).
I have noticed in the configuration page on the controller Wireless>802.11b/g/n > High Throughput is disabled. (See attached screenshot)
I don’t want to just enable this setting in case it disconnects all the users from all the AP’s not just the ones at head office.
We use 802.1x for authentication and Machine certificates.
All Clients connect using WPA2.
Would this settings increase the connection speed up to 802.11n?
Is there a way to just enable it on 1 AP to trial it before enabling it on all the AP’s?The wireless speed is only 15-20mbps Max. When connected via Lan cable the speed is around 45mbps.
As scott said, you are getting this speed due to the half duplex nature of wireless. If your AP model is 1142, then you can configure radio1 interface (5GHz) for the SSID. You MUST use WPA2/AES or Open Auth in order to get 802.11n speeds which is greater than 54Mbps. I do not think you are using that at the moment & it may be a reason why clients data rates not get 802.11n speeds.
Below shows different AP model max data rates. If your clients having multiple spatical stream (SS) capability they can get higher speeds. Note that 20MHz BW is the max you can get in 2.4GHz band & 40MHz bandwidth you can get from 5GHz with channel bonding. So 5GHz is always better if you looking for higher througput (but obviously client should able to connect in 5GHz)
Adding antoher AP would be a good idea (without bridging) & see wether you could afford 2602 or 3602 which can go upto 450Mbps data rates . Practically if you could you get 50% (which is around 200Mbps) that is really good. Note that this is total AP througput & if you connect multiple clients that will be shared among users.
Also keep in mind when you add multiple users all users aggregate bandwidth is limited to 50Mbps due to your WAN link speed. So that would be the bottleneck within your network.
HTH
Rasika
*** Pls rate all useful responses *** -
I keep getting an error message when trying to log on to FaceTime and iMessage on my iPad mini with wifi...Could not sign in. Please check your network connection and try again. Help!
Using FaceTime http://support.apple.com/kb/ht4319
Troubleshooting FaceTime http://support.apple.com/kb/TS3367
The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
http://tinyurl.com/a7odey8
Troubleshooting FaceTime and iMessage activation
http://support.apple.com/kb/TS4268
Using FaceTime and iMessage behind a firewall
http://support.apple.com/kb/HT4245
iOS: About Messages
http://support.apple.com/kb/HT3529
Set up iMessage
http://www.apple.com/ca/ios/messages/
Troubleshooting Messages
http://support.apple.com/kb/TS2755
Setting Up Multiple iOS Devices for iMessage and Facetime
http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
FaceTime and iMessage not accepting Apple ID password
http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
Unable to use FaceTime and iMessage with my apple ID
https://discussions.apple.com/thread/4649373?tstart=90
For non-Apple devices, check out the TextFree app https://itunes.apple.com/us/app/text-free-textfree-sms-real/id399355755?mt=8
Cheers, Tom -
After the update I am unable to log in to get iMessages. It says "Could not sign in. Please check your network connection and try again". My phone is connected to Wi-fi. What should I do?
Hi andrea110,
Welcome to the Support Communities!
The article below may be able to help you with this issue.
Click on the link to see more details and screenshots.
The settings are the same for iOS 7:
iOS 6 and OS X Mountain Lion: Link your phone number and Apple ID for use with FaceTime and iMessage
http://support.apple.com/kb/HT5538
iOS: Troubleshooting Messages
http://support.apple.com/kb/TS2755?viewlocale=en_US
Cheers,
- Judy -
I have taken on an existing vb.net project done in Visual Studio 2008 with crystal reports version Crystal Report XI.
The reports on their own work very well. Problem is I need to add information to my report which is a 'many-to-one' situation where for each Project Id that I am displaying I need to display several attached documents and the report I am working on is for several Project Id's.
I figured this would be a perfect situation for a SubReport. I created a separate report which calls a stored procedure to get all of the Attached Documents for a specific Project Id. I thought if I were to add this new SubReport to the Original Report and link the Project Id's, easy-peazy, I would be done.
This is not the case. I have vb code that loads the Original Report with a stored procedure and when this code runs with the setup I described above it fails when it is creating the final report with the following error:
Logon failed. Details: crdb_adoplus : Object reference not set to an instance of an object. Error in File C:\~\ProjectDescriptionReport {6BA19F79-2A12-4826-B1F6-456EF799963B}.rpt: Unable to connect: incorrect log on parameters.
I have no specific connections in my vb code for the reports. If I do not add the subreport to the main report, it loads correctly, so I know the error is caused by the subreport.
This is the code that creates the original report (sorry for dumping the code here, i just thought it would be easier to see all the code) :
Public Function LoadReport(ByVal inProjectNum As Integer, ByVal strProjectName As String) As DataTable ', ByVal inFiscalYear As Integer, ByVal inCompany As String) As DataTable
Dim cnn As SqlConnection = Nothing
Dim cmd As Data.SqlClient.SqlCommand
Dim obj As New clsDataClass
Dim dataAdapter As SqlClient.SqlDataAdapter
Try
LoadReport = New DataTable("DescriptionReport")
cmd = New SqlCommand()
cnn = obj.Create_Connection()
With cmd
.CommandType = Data.CommandType.StoredProcedure
.Connection = cnn
.CommandTimeout = "60"
.CommandText = "usp_GetProjectGroupSpecsCR"
.Parameters.AddWithValue("@ProjectNumber", inProjectNum)
.Parameters.AddWithValue("@ProjectName", strProjectName)
End With
dataAdapter = New System.Data.SqlClient.SqlDataAdapter
dataAdapter.SelectCommand = cmd
dataAdapter.Fill(LoadReport)
Dim oRpt As New ReportDocument()
oRpt.Load(Server.MapPath("ProjectDescriptionReport.rpt"))
oRpt.Refresh()
oRpt.SetDataSource(LoadReport)
'oRpt.OpenSubreport("AttachmentsReport").SetDataSource(LAR)
oRpt.SetParameterValue("inProjectNum", inProjectNum)
oRpt.SetParameterValue("strProjectName", strProjectName)
oRpt.ExportToHttpResponse(ExportFormatType.PortableDocFormat, Response, True, "Projects_DescriptionReport") 'inCompany & "ProjectsReport_Description" & inFiscalYear) <-- Line where the error occures.
What I need to know is what is the proper way to add a subreport to a vb.net application?
From the ways I have tried it is clearly not working and I am out of ideas. I am fairly new to Crystal Reports and this way of coding it.
Any help for this would be greatly appreciated, I've been stuck on this for a while and am finally reaching out to the Crystal Report Specialists.
Thank you in advance,
BryanHi Bryan,
You may want to check the Connection properties also. I think the MS Data.SqlClient.SqlCommand is using the MDAC driver, or could be modified.
If you are connecting to SQL Server 2008 or above you should be using the SQL Native 10 or 11 Client.
As Dell suggests have a look at the samples and if you can use a DSN ( 32 bit or 64 bit ODBC Admin )
Also search for "CRlogger", you'll find how to enable CR's database logging component and may help show you what part is failing.
Don
Maybe you are looking for
-
STPPOD Idoc creation status : Error in ALE Service
Experts, I am trying to send GR from MM to SUS in MM-SUS Classic Scenario on ECC 6.0 Server. I have also configured Goods REceipt Notifications Functionality to sending GR from MM to SUS. When i am trying to send GR Idoc is generated (STDPOD) but i a
-
Unable to type the maximum limit in scientific notation in a plot
Hi, I am trying to plot some data that I measured in scientific notation (2E-19, etc) and I have tried everything to manually set the maximum/minimum limits of my plot in either axis without success. I have typed 2E-19 and even the number will all th
-
Hi Everybody, I have to start a process at beginning every month selecting data from the past month. sample start date 1st July, data select from 1st June until 30 June. At the time I start it manually.. is there a possibility to do that automatical
-
Preserving Safari history for use in a new iMac installation
My Mother is ready for a new iMac but has a strong afinity to using the Safari history for browsing sites she's accessed previously. Reading about Safari history has alerted me to the "plist" file that the history is saved in. I need to determine h
-
Indesign trial version Windows vista
Hi There, I use Windows Vista (32 bit system, 4 GB RAM) and wanted to download a trial version of Indesign. Unfortunately, the CC version does obviously not support Windows Vista. CS6 or CS5 would also be ok for the beginning, but for this versions I