Aironet 1250, and CAll Manager

Hii Experts,,
Dis any one can help me to fine package for aironet 1250 to use it with CiscoWorks LMS 2.5 the device appear as unknown device and I cannot veiw it in Cisco veiw, and if there is a package for call manager 4.2.
Thanks for you supports.

CCM is not supported by the LMS.
Here is the URL for the supported device table for LMS
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.1/device_support/table/lms31sdt.html#Voice

Similar Messages

Aironet 1250 and AIR-ANT2430V-R

Hello,
I've just installed a Aironet 1250 and AIR-ANT2430V-R antenna.
I could do with some pointers on configuring the 2.4Ghz radio interface.
Role: Access Point
Goal: Blanket office coverage
Channel width: 20Mhz or 40+ ?
External Antenna Configuration: Enable
Gain: ??db
Currently I'm seeing speeds between 1Mbps and 144Mbps, with sporadic coverage.
I was expecting Â£900+ equipment to be better than the Â£10 D-link POE WAP currently installed! =]
Thank you in advance
K

Do you have the rp-tnc connectors fastened tightly?
How are you measuring the bitrate?
Also, have you tried using a tool such as iperf to measure actual throughput and not bitrate?
If you are running 802.11n rates on the 2.4 spectrum and plan to deploy more APs on the network, you will want to stay away from channel bonding.
We do not run 802.11n on the 2.4 side, only the 5Ghz side.

Which Ports do MCU and Call Manager use for Video?

Hi, Does anyone know which ports the MCU and call Manager Use when using the 3511 MCU box with Call Manager 4.1.3. I am looking to open the appropriate ports on the firewall.
Regards
Dominic

Dominic,
If your MCU ports are Callmanger controlled, they will use Skinny (SCCP) to communicate on TCP port 2000. Please see the following link.
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a00801a62b9.shtml
Hope this helps. If so, please rate the post.
Brandon

Cisco Unified Contact Center Express 8.5 and Call Manager 8.5 on single ESXi

Does Cisco support 2 virtual machines (on ESXi), one for Cisco Unified Contact Center Express 8.5 and one for Call Manager 8.5?
I have blade ucs b200.
Thanks a lot, Svetomir

Yes it is supported. Check this out http://docwiki.cisco.com/wiki/Unified_Communications_Virtualization_Sizing_Guidelines#Sizing_Examples
GP.
Pls rate helpful posts by clicking on stars below the post !!

NetMeeting and Call Manager

i know that Cisco IP-softphone inetgrates NetMeeting, but the Question: can we use NetMeeting as a Softphone with the Call Manager?

any tips on how to configure this? or any link or website
I need to provide NetMeeting and/or other H323 client that supports NAT for some of my customer.
So I want to setup h323 client instead of Cisco IP SoftPhone which is huge and does not support NAT
Faisal

NICE and Call Manager integration

Did anyone successfully integrate cisco call manager 4.3 with NICE recording system. What were the steps taken for integration.
Regards.

On CM, nothing.
On the switch, span voice gateway port to voice recorder server port .
Voice recorder configured as per vendor documentaion.

Purged logs on Unity and Call Manager

Some time I see diferent hard disk are full or closer to be full. When I check confirm so a lot of logs file are create, my undecitions, What is/are the logs file that I must be delete en my servers ( Unity and Pub/Susb )
I like to implement a script to auto purge, I don't know.

I can not speak to Unity but CCM will purge logfiles & not fill the drive if configured properly. YOu need to go to the CCM Serviceability page and adjust the number of retained logfiles for eack service so the drive does not fill. By default each service will keep 250 files 10000 lines long.
There are a couple of things that consume disk space on the CCM. You shoud also check the SQL DB transaction logs to make sure they are not growing. Also ensure that you are purging the CDR & ART DBs
Mike

Cisco Call Manager 8.5 and Lync 2013

Dear all,
Our customer wants to integrate their Lync 2013 to the Cisco Call Manager 8.5.
Out of some not so recent information i thought that if u want to use the enterprise voice of lync you'll have to make a sip trunk between Cisco Call Manager & Lync 2013.
I think that this still counts, i've also heard that there have been a moderate amount of changes between cucm 8.5 and cucm 8.6 on matters of sip.
I'm unable to find them though, also what does CUCI - Lync do?
Kr,
Yannick Vranckx

Hi Yannick,
There can be three types of integrations between Lync and Cisco Systems
1) Direct SIP Trunk between Lync Server and Call Manager - In this, we can setup shared line between Cisco extensions and Lync extensions, and Sip trunk between the servers. Any Cisco phone / Lync client can call each other vice-versa. Initial setup needs planning, but later it does not need much configurations in client side. The following document explains the configurations needed.
http://www.cisco.com/en/US/docs/voice_ip_comm/cucilync/9/CUCI_BK_C0B36AC1_00_cisco-uc-integration-for-microsoft.pdf
2) CUCILYNC, which is like Cisco Jabber client but connects with Lync and Call Manager: Lync Client <----> CUCILYNC <-----> CUCM
In this option, a plug-in is installed in each client side. Although initial configurations is easier, each user needs to install the client and operate it. The below document explains the configuration and setup.
http://www.cisco.com/en/US/docs/voice_ip_comm/cucilync/9/CUCI_BK_C0545A41_00_cisco-uc-integration-for-microsoft.html
3) RCC (Remote Call Plugin) which just provides basic call control feature but for that you need Cisco Unified Presence Server: Lync Client <----> CUPS <-----> CUCM
HTH
Manish

Cisco call manager and ip phone software.

Hi everybody.
Does Cisco call manager also include software required for ip phone? Or software for ip phone needs to be installed on tftp server and it does not come with cisco call manager.?
thanks and have a great weekend.

Hi Sarah,
by ip phone software, do you mean Cisco IP Phone Agent software?
if yes, then you need to have Customer Response Solution (CRS) and Call Manager together to setup ip phone software (services).
check this link for further info:
http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_configuration_example09186a00801c5765.shtml
plz Rate if it helped.
Soroush.

Cisco Call manager 7.2 through ASA firewall

Hi,
We have a part of our building that we have sold to another company. We still have to provide them with some resources until they can install their own network. We have a 6500 switch there and we are going to implement a ASA in between and lock down most communication. One of the resources required are Cisco IP phones.
Does anyone know which ports etc are required to be opened to allow communication between these phones and Call manager and other IP phones on the site?
Any help would be appreciated

Hi Andrew
The attached document may assist:
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/port/7_0/CCM_7.0PortList.pdf
A lot depends on topology etc, and the handset registration protocol you are using (SIP vs SCCP).
Hope this helps.
Barry Hesk
Intrinsic Network Solutions

Unable to Connect to Cicso Aironet 1250

My office just bought the Cisco Aironet 1250 and I am task to set it up. Right now, I am unable to connect to AP even when it is configured as Open Authentication without encryption. Tried using both laptops and our products to no avail. The same laptops and products are able to connect to other wireless routers So far, only my Linksys Wireless-G USB network Adapter is able to detect it.
We are very puzzled by this because we are able to setup and connect to it initially. But when we try to reconfigure it to another setting, everything starts to fail. We have tried doing factory default.
The AP is connect only to a Windows 2003 Server running DHCP and IAS. Appreciate if someone can help me on this. Thanks

Hi All,
Here are screen capture of my configuration
http://img.photobucket.com/albums/v146/tiger3687/Cisco%20AP%201250/ExpressSetup.jpg
http://img.photobucket.com/albums/v146/tiger3687/Cisco%20AP%201250/Security-EncryptionManager.jpg
http://img.photobucket.com/albums/v146/tiger3687/Cisco%20AP%201250/Security-EncryptionManager.jpg
http://img.photobucket.com/albums/v146/tiger3687/Cisco%20AP%201250/Security-SSIDManager02.jpg
http://img.photobucket.com/albums/v146/tiger3687/Cisco%20AP%201250/Security-SSIDManager03.jpg
http://img.photobucket.com/albums/v146/tiger3687/Cisco%20AP%201250/Security-SSIDManager03.jpg
http://img.photobucket.com/albums/v146/tiger3687/Cisco%20AP%201250/Security-SSIDManager03.jpg
http://img.photobucket.com/albums/v146/tiger3687/Cisco%20AP%201250/Security-ServerManager.jpg

Cisco Prime Infrastructure 1.2 and Aironet 1250 + VSS issues

Hi,
I am new to the NCS implementations and configurations. I have one very specific case with Cisco Prime Infrastructure 1.2 and autonomnous APs and several issues with Cisco VSS on 6500 switches.
So here is the version from Prime:
NCS/admin# show version
Cisco Application Deployment Engine OS Release: 2.0
ADE-OS Build Version: 2.0.1.038
ADE-OS System Architecture: x86_64
Copyright (c) 2005-2010 by Cisco Systems, Inc.
All rights reserved.
Hostname: NCS
Version information of installed applications
Cisco Prime Network Control System
Version : 1.2.1.012
IOS version on our APs (which are autonomnous) is:
AP-N-1>show ver
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(25d)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 11-Aug-11 03:23 by prod_rel_team
Well the issue what we have now is that access point has been added but its not recognized by the NCS prime. I have tried all three versions of SNMP but I get the same result. The SNMP configuration is valid since I use the same for my switching infrastructure. When I enter "debug snmp packets" and "terminal monitor" I can see the SNMP communication between Prime and Aironet 1250 which is standalone.
When I switch to Lifecycle theme and go to Operate > Device Monitor Center I see all devices I have added. The Aironet 1250 is reachable but under collection status I get Managed with Warnings. When I hover over with my mouse I get "None available".
I have successfully added my switching infrastructure in total, which is operating perfectly for Catalyst 2960/3650/3750/4500 series but for 6500 under VSS I have some warnings. The device is recognized by the system which is excellent and all is operational. I get the following errors under Collection Status:
feature_sensor
SNMP request timed out
feature_powerSupplyFanStatus-6k
SNMP request timed out
IdentityCapability
The device is unreachable.
feature_flashdevice
SNMP request timed out
sam_ipsla_feature
The device is unreachable.
What can be done to resolve these issues ? I have attached a screenshot of this particular issue. The affected access point is 172.16.165.241.
Predrag Petrovic

Hi rajeeshp,
Currently I am not allowed to upgrade it because of internal procedures involved in upgrading a specific piece of software (obtaining permissions from various departments). Is it free to upgrade from 1.2 to 1.3 or there is a specific charge for that.
Predrag Petrovic

4 Aironet 1250's and a controller?

Hi guys,
I'm about to order a four Aironet 1250's and a 2106 Wireless LAN Controller. From what I've read, I'll need the controller to manage the APs if I want them all to offer the same broadcast domain and subnet, and offer roaming to the users. Often times what I read and understand turns out to have little to do with reality, so my question is, am I correct about this?
Thanks in advance!
Joe

http://www.cisco.com/en/US/docs/wireless/controller/4.2/configuration/guide/c42ovrv.html#wp1133151
These hardware features are not supported on 2000 and 2100 series controllers:
•Power over Ethernet (PoE) [2000 series controllers only]
Note Ports 7 and 8 on 2100 series controllers are PoE ports.
•Service port (separate out-of-band management 10/100-Mbps Ethernet interface)
These software features are not supported on 2000 and 2100 series controllers:
•VPN termination (such as IPSec and L2TP)
•Termination of guest controller tunnels (origination of guest controller tunnels is supported)
•External web authentication web server list
•Layer 2 LWAPP
•Spanning tree
•Port mirroring
•Cranite
•Fortress
•AppleTalk
•QoS per-user bandwidth contracts
•IPv6 pass-through
•Link aggregation (LAG)

Toll fraud traffic pumping on a Call manager express and unity express with an 800 toll free number.

I have a customer with a call manager express and a unity express. They have an 800 toll free number that rings in to an auto attendant on the CUE. The problem is something called toll fraud traffic pumping. The caller, always from a different number, reaches the auto attendant by dialing the 800 number. They then somehow manage to keep the line connected for up to 12 hours by somehow staying in the auto attendant. I opened a TAC case and was informed that it is not in Cisco's hands to create a way to disconnect a call that is connected to the CUE. I need a way to have a call that stays in the auto attendant or voicemail after 3 to 5 minutes. I can't see a way to do it in the auto attendant script. Can someone help with a method that will disconnect the caller if they stay in the CUE for a period of time?

Thank you for the response Jaime.
That is what TAC told me. I am not familiar with TCL scripting and I have been looking at some guides on it. Any advice on a source to go to for assistance with that, possibly someone to help?

Is it possible to take the CDR data from a v4.2 Call Manager and copy it to a separate server where it would be made available for reporting?

Is it possible to take the CDR data from a v4.2 Call Manager and copy it to a separate server where it would be made available for reporting? We are not interested in migrating the CDR data to v6 because of the concerns it introduces to the upgrade process. Is it possible to get the raw data and somehow serve it from a different machine? (knowing it would be 'old' data that stops as of a certain date). If so, what would be the complexity involved in doing so?
It seems like the CDR data lives within MSSQL and the reporting interface is within the web server portion of the Call Manager... that's as far as we've dug so far.

Hi
It is absolutely possible to get the data - anyone you have in your org with basic SQL skills can move the data off to a standalone SQL server. This could be done most simply by backing up and restoring the DB using SQL Enterprise Manager.
Moving the CAR/ART reporting tool would be more difficult... if you do actually use that for reporting (most people find it doesn't do what they need and don't use it for anything but basic troubleshooting, and get a third party package) then the best option may be to keep your publisher (possibly assigning it a new IP) and leave it running for as long as you need reporting.
You would then need a new server to run your upgraded V6 CCM; you may find you need this anyway.
Regards
Aaron
Please rate helpful posts...

Aironet 1250, and CAll Manager

Similar Messages

Maybe you are looking for