Aironet 1300 cannot access by iphone

I use the aironet 1300. In windows perform it can detected the sid and applied the ip but when i use apple iphone it just detected the sid but cannot apply ip. so how can i do.

Hello,
i'm a french user of behance, on i've got the same problem as Sarah; i can connect on my account on internet but with my iphone it
doesn't work. I delete then reinstall the app and restart the phone, but it is the same. I recieve popup from beahnce on the phone as if i'm connected, but i cannot
access on the app....
Thank you very much for your answer

Similar Messages

I have broken my screen and cannot access my iphone. I have an icloud account which I have used to back up my phone previously but nothing is showing on the website. How can I backup my data?

I have broken my screen and cannot access my iphone. I have an icloud account which I have used to back up my phone previously but nothing is showing on the website in contacts etc. As I can enter my pin I cannot connect it to a laptop. Is there anyway of backinh up my data, pictures etc?

No there isn't. If you check iCloud, you are not showing any backups at all? Did you have the phone set to sync contacts in iCloud, or were you just backing up to iCloud? If you were just backing up, then you should be able to access the backup, but if you were not syncing, then you probably cannot see the contacts in iCloud. You would have to wait until you restore from the backup to see them. You will probably have to go onto the iCloud website to erase and remove the device from Find My iPhone if you want to clear it off.

Cannot access my iphone

I logged into iCloud then to the Find My iPhone app. As I am planning to sell my iPhone, I thought it should be deleted from iCloud so I went ahead and deleted it. Now I cannot access my iPhone cause it is reported stolen. Please advise! Thanks.

You may be right. Basically the sim got locked as I reported it stolen. I will get a new sim and see how it goes. Thanks for the effort luuklp & KiltedTim.

HT3204 i cannot access my iphone what i need to do?

i cannot access my iphone,wt i need to do?

See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
But... if the Device has been Modified... this will Not necessarily work.
Note:
You have not stated which iPhone you have and which iOS it is running.

Cannot access 2g iPhone

I recently bought an iPhone 2g off ebay planning to use it as an ipod/camera.
I read that I could use a de-activated sim card to turn the phone on. I bought one and installed it. The no sim card message go's away, but I am still stuck at the emergency call screen and cannot access my iPhone.
Do I have any options?
Thanks, Scott

http://support.apple.com/kb/HT3406

Cannot access my Iphone 3gs after upgrading to 5.01

Hi,
I bought an unlocked Iphone 16BG 3Gs from eBay. I used it for a week
TillI connected my Iphone to ITunes and they notify me I needed to upgrade my
Software and I accept.
That was the mistake I made as it upgraded to 5.01 and I cannot access
myphone. When I put on my phone I am getting the activation screen. I try completing the activation but with no success. When I connect my phone to USB and start Itunes I am getting error message
"There is no Sim card installed in the Iphone your are attempting to
activate"
I tired the following with no success.
Itried downgrading from 5.01 to 4.33 by downloading firmware from google. Holding shift button and clicking restore onITunes, selecting the firmware but I am getting error message" Iphone“Iphone” could not be restored. An unknown error occurred (3194)
I also tried using RedSn0w program and Tiny Umbrella and no luck at all.
Please help.
Thanksyou,
Charles.

Is the SIM that is installed from the carrier the device is locked to?
Was the device hacked or jailbroken? Possibly to unlock the device?

Image Recovery for Cisco Aironet 1300 Outdoor Access Point

We purchased two 1300 APs for outside. There is a new release for the image that we wanted to use so, we have the latest security updates. We downloaded, logged onto the access point just fine, but the image never took. After four hours with a direct connection, it was still going and this morning we came in and it just keep rebooting. Our network guy states it looks like a corrupt image. We can barely do anything and since there is no "mode" button like the earlier models, I have not found anything on web sites or forums to help us reload a good image to the access point. I would appreciate any insight someone has and/or where to look for this. I logged on and downloaded about every manual on the 1300 I could find, but have not found a good way to fix this. Not even the upgrade tool will connect since it just keeps rebooting.

Hi Bruce,
Because (as you correctly noted) the 1300 does not have a mode button you could try this method;
Complete the steps in this section in order to reset Cisco IOS Software-based bridges:
If the privileged command prompt ap# is available in the CLI, the write erase command and the reload command erase the startup configuration and reset the unit.
If the GUI is available, choose System Software > System Configuration. Press the Reset to Defaults button.
Aironet 1300 Series Bridges do not have a MODE button to reset the AP to factory defaults. So, if neither the GUI or CLI is available with sufficient privileges, complete these steps to delete the current configuration and return the entire bridge settings to the factory defaults using the CLI.
Open the CLI with a Telnet session or a connection to the bridge console port.
Reboot the bridge by removing and reapplying power.
Allow the bridge to boot until the command prompt appears and the bridge begins to inflate the image.
Press ESC when you see lines that are similar to these on the CLI:
Loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_ja.20040314"
...#############################################################################Note: In order to access the boot loader, you must press ESC twice. But this action depends on the terminal-emulation software that you use.
Messages that are similar to these appear:
Error loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_
ja.20040314"
Interrupt within 5 seconds to abort boot process.
Boot process terminated.
The system is unable to boot automatically. The BOOT environment variable needs to
be set to a bootable image.
C1310 Boot Loader (C1310-BOOT-M), Version 12.2 [BLD-v122_15-ja_throttle.20040314 100]
bridge:At the bridge: prompt, issue the dir flash: command in order to view a directory of the Flash file system.
The directory is similar to this directory:
bridge: dir flash:
Directory of flash:/
2 -rwx 0 env_vars
5 drwx 384 C1310-k9w7-mx.v133_15_JA.20040314
3 -rwx 1128 config.txt
4 -rwx 5 private-config
3693568 bytes available (4047872 bytes used)
bridge:Delete or rename the files config.txt and env_vars, and reboot the bridge.
Note: Do not forget the / character before the filenames.
bridge: delete flash:config.txt
Are you sure you want to delete flash:/config.txt (y/n)?y
File "flash:/config.txt" deleted
bridge: delete flash:/env_vars
Are you sure you want to delete "flash:/env_vars" (y/n)?y
File "flash:/env_vars" deletedIssue the boot command in order to reboot the bridge at the bridge: prompt, or simply power cycle the bridge.
After the bridge reboots, reconfigure the bridge with the web browser interface, the Telnet interface, or Cisco IOS Software commands.
Note: The bridge is configured with the factory default values that include:
The IP address, which is set to receive an IP address with DHCP. If you do not have a DHCP server, you can access the bridge using the default IP address of 10.0.0.1 using HTTP/HTTPS or Telnet. Once you gain access to the bridge via Telnet or GUI, you can modify the IP address of the bridge.
Note: This default IP address of 10.0.0.1 becomes available only for a short period. So, make sure that you assign your own IP address to the bridge within that period of time.
The default username and password, "Cisco".
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_password_recovery09186a00800949d0.shtml#ca_1310_ser
One other thing, be careful with the new IOS that you aren't loading a LWAPP Recovery Image. (it almost sounds like what may have happened)
Hope this helps!
Rob

HT1688 forgot passcode cannot access my iphone

forgot passcode cannot access my iphone

Locked Out, Forgot Lock or Restrictions Passcode, or Need to Restore Your Device: Several Alternative Solutions
A
1. iOS- Forgotten passcode or device disabled after entering wrong passcode
2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
3. Restoring iPod touch after forgotten passcode
4. What to Do If You've Forgotten Your iPhone's Passcode
5. iOS- Understanding passcodes
6. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
7. iOS - Unable to update or restore
Forgotten Restrictions Passcode Help
iPad,iPod,iPod Touch Recovery Mode
You will need to restore your device as New to remove a Restrictions passcode. Go through the normal process to restore your device, but when you see the options to restore as New or from a backup, be sure to choose New.
You can restore from a backup if you have one from BEFORE you set the restrictions passcode.
Also, see iTunes- Restoring iOS software.

Cannot access to iPhone behance apps

i'm a french user of behance, on i've got a problem on the iphone app; i can connect on my account on internet but with my iphone it
doesn't work. I delete then reinstall the app and restart the phone, but it is the same. It is as i'm still connected because I recieve popup from beahnce on the phone, but i cannot
access on the app to my account....
When i try to log and enter connection, it reload the page "connect or subscribe" again and again and again...
Thank you very much for your answer

So that we can provide the best support, can you send us a ticket here? We'll get back to you within a few hours with one-on-one help: Behance Support & Forum : Submit a request for assistance

Cannot access Apple ID, and therefore cannot access reset iPhone

Okay, so I went to update my iPhone 4S to the latest software update (7.02 from 7.0 I believe). The new update downloaded, installed and as my computer went to restore my backup it asked to plug in my iPhone to my computer (which it already was). I left it for a long while and nothing happened so i disconnected it and reconnected - upon which it did a factory reset - which i was fine with because I have a back-up.
However, upon reset iTunes tells me that my phone is linked my apple ID account and displays the email address to which it is linked. I try every possible password to no avail. I then go to reset my password but Apple never send an email through to the email address in question,despite a number of attempts. I then decide to create a new Apple ID - and entered the email address for which iTunes said my phone was linked to...and it says that the address isn't in use...
I am completely stuck for what to do as i cannot currently access my iPhone.

This feature has been introduced to make stolen phones useless to those that have stolen them.
However it can also arise when the user has changed their Apple ID details with Apple and not made the same changes to their iCloud account/Find My Phone on their device before upgrading to iOS 7, or if you restore from a previous back up made before you changed your details.
The only solution is to change your Apple ID back to its previous state with Apple at My Apple ID, verify the changes, enter the password as requested on your device and then turn off "find my phone".
You should then change your Apple ID back to its current state, verify it once again, delete the iCloud account from your device and then log back in using your current Apple ID. Finally, turn "find my phone" back on once again.
This article provides more information about Activation Lock.

Cisco Aironet 1131G cannot access BVI

I have configure our Cisco Aironet 1131G with Multiple SSID with VLAN's
The Guest VLAN is working well and no problem,
The issue i have is that I cannot connect to the BVI on the Wireless AP, i have setup to VLAN's
2 = LAN & NATIVE VLAN
999 = GUEST VLAN
this is my config
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname NAFTA_AP_003
logging rate-limit console 9
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa group server radius rad_eap2
server 10.1.122.50 auth-port 1645 acct-port 1646
aaa authentication login default local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authentication login eap_methods2 group rad_eap2
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
dot11 mbssid
dot11 syslog
dot11 vlan-name GUEST vlan 999
dot11 vlan-name LAN vlan 2
dot11 ssid Nufarm_EXT
   vlan GUEST
   authentication open
   authentication key-management wpa
   mbssid guest-mode
   wpa-psk ascii 7 053B0918245E6308015546
dot11 ssid Nufarm_INT
   vlan 2
   authentication open eap eap_methods2
   authentication network-eap eap_methods2 mac-address mac_methods
   authentication key-management wpa
username nemesis privilege 15 secret 5 $1$SjHa$TGIGBh.IhLNgflxBreKYf.
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan GUEST mode ciphers aes-ccm tkip
encryption vlan 2 mode ciphers tkip
ssid Nufarm_EXT
ssid Nufarm_INT
channel 2422
station-role root
interface Dot11Radio0.2
encapsulation dot1Q 2 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.999
encapsulation dot1Q 999
no ip unreachables
no ip proxy-arp
no ip route-cache
no cdp enable
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
bridge-group 255 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.2
encapsulation dot1Q 2 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.999
encapsulation dot1Q 999
no ip unreachables
no ip route-cache
no cdp enable
bridge-group 255
no bridge-group 255 source-learning
bridge-group 255 spanning-disabled
interface BVI1
ip address 10.1.2.242 255.255.255.0
no ip route-cache
ip default-gateway 10.1.2.254
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server attribute 32 include-in-access-req format %h
radius-server host 10.1.122.50 auth-port 1645 acct-port 1646 key 7 03516213160B73435E0C2D16110504
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 0 4
end

Ah, yeah that would do it, makes the swich want the VLAN to be tagged. Nice catch on that!
HTH,
Steve
Please remember to rate helpful posts or to mark the question as answered so that it can be found later.

HT1386 can hear phone ringing, screen is blank, cannot access the iphone

help! my phone is ringing but screen is blank- cant access phone... any ideas?

Do a
Reset: Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Note: You will not lose any data

HT1766 My iPhone 5 "froze" and the only item that is displayed is an iTunes logo (musical notes) and a white USB cord with arrow pointing towards the logo. I cannot access the iPhone through my computer or get it to do anything else. Dave

While attempting to set up my new iPhone for iTunes the first time, an error message displayed on my computer saying that I needed to restore it to my factory settings and the only function that the iPhone displays is the message listed above.

that's the exact same thing that happened to my iPhone 5. (see my thread) Well that occured after I downloaded the iOS 6.2. The very same image appeared to my phone. What I did was (well the situation left me no option) restored it to factory settings. However, your iTunes must dowload (i think) new version of software for your phone. It took me 3 hrs!. But I also have to warn you. It may still ask you to restore again, and again, and again, after each restoration.
What I did was, disconnect the cable from your phone and computer, then press the power and home button together, hold it down lke that till the apple logo appears. The phone successfully worked but Siri & the voice command keep messing with my calls, playing music by itself, returning to home by itself.

HT5624 How can I turn off iMessage if I cannot access my iPhone?

I ported my number to another carrier and switched to a different phone, but I didn't turn off iMessage before doing so. Now I can nolonger receive text messages from iPhone users. How can I remedy this?

Go to -> https://supportprofile.apple.com/MySupportProfile.do
log in with your AppleID and unregister your iPhone.

Cannot access my iphone it says should turn of the find my iphone

please help...

Okay, if you cannot remember your passcode, see this support document for help. http://support.apple.com/kb/ht1212

Aironet 1300 cannot access by iphone

Similar Messages

Maybe you are looking for