Aironet 1300 Point to Point not Communicating

Hi,
I am trying to set up (2) 1300 bridges, but I can not get them to talk to eachother. They currently have no external antennas connected, and are about 50ft apart (for setup/configuration purposes). Is there any where to find a document that shows how to set them up w/o a radius server or leap configurations. I'm really looking to just get them to talk to eachother first and formost. Thanks for any help.

Hi,
I guess that you must be referring to this document:
http://www.cisco.com/en/US/tech/tk722/tk809/tech_configuration_examples_list.html
The main thing is to configure the same SSID, with the same security settings, on both the root and non-root. So you can use the Web interface, no VLAN, one radio.
1. Go to express security, on the Web interface, and create an SSID, with no security. Do the same on both access points.
2. Go to the AP radios, set one AP to root bridge, the second to non root bridge, enable the radios, it should work...

Similar Messages

  • Aironet 1300 Point to Point Bridging

    Hi, I am new to the forums so please accept my apologises if this is really easy question!!
    We have purchsed 2 Aironet 1300's that we are wanting to use to create a bridge, but after hours of trying and net searching we cannot get them to talk to each other. Can anyone please help? Thanks

    Here's the online config guide:
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008058f53e.shtml
    Here's the Point-to-Point Troubleshooting FAQ:
    http://www.cisco.com/en/US/products/hw/wireless/ps2360/products_qanda_item09186a00801d29ff.shtml
    Wireless Point-to-point Troubleshooting Guide:
    http://www.cisco.com/en/US/products/hw/wireless/ps2360/products_tech_note09186a00801d2a0c.shtml
    Sample Config and Command Guide:
    http://www.cisco.com/en/US/products/hw/cable/ps2217/products_configuration_example09186a0080193dac.shtml
    Other possible issues are to make sure you have solid line-of-site ("more than you think you need" because of some properties associated with the "Freznel Zone")
    Check it out and let us know if you are still having problems.
    Good Luck
    Scott

  • CISCO Aironet access point - not able to connect by user.

    Hi,
    I have CISCO Aironet access point C1130 in my network , but not able to connect by users, I can see below logs from access point. please help on this.
    Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:20.544: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:20.544: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:24.832: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:24.832: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:29.741: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:29.741: RADIUS: Fail-over denied to  (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:29.741: RADIUS: No response from (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:29.741: RADIUS/DECODE: No response from radius-server; parse response; FAIL         
    Jun 13 17:50:29.741: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL         
    Jun 13 17:50:29.741: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAILOVER_RETRY         
    Jun 13 17:50:29.742: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response         
    Jun 13 17:50:29.742: Client 5864.6c67.3718 failed: EAP reason 0         
    Jun 13 17:50:29.742: dot11_auth_dot1x_parse_aaa_resp: Failed client 5894.6b37.3518 with aaa_req_status_detail 0         
    Jun 13 17:50:29.742: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for 5894.6b37.3518         
    Jun 13 17:50:29.742: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client 5894.6b37.3518         
    Jun 13 17:50:29.742: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds         
    Jun 13 17:50:29.743: dot11_auth_dot1x_send_client_fail: Authentication failed for 5894.6b37.3518         
    Jun 13 17:50:29.743: %DOT11-7-AUTH_FAILED: Station 5894.6b37.3518 Authentication failed
    Regards,       

    Hi Niham,
    You can try few things to troubleshoot this -
    1. check the reachability of Radius server from your wlc (ping).
    2. verify the IP address of Raduis server configured on wlc.
    3. wlc in the Radius server ?
    4. Shared Secret must be same on wlc and in raduis server.
    Plz do not forget to rate useful post.
    Thanks

  • Image Recovery for Cisco Aironet 1300 Outdoor Access Point

    We purchased two 1300 APs for outside. There is a new release for the image that we wanted to use so, we have the latest security updates. We downloaded, logged onto the access point just fine, but the image never took. After four hours with a direct connection, it was still going and this morning we came in and it just keep rebooting. Our network guy states it looks like a corrupt image. We can barely do anything and since there is no "mode" button like the earlier models, I have not found anything on web sites or forums to help us reload a good image to the access point. I would appreciate any insight someone has and/or where to look for this. I logged on and downloaded about every manual on the 1300 I could find, but have not found a good way to fix this. Not even the upgrade tool will connect since it just keeps rebooting.

    Hi Bruce,
    Because (as you correctly noted) the 1300 does not have a mode button you could try this method;
    Complete the steps in this section in order to reset Cisco IOS Software-based bridges:
    If the privileged command prompt ap# is available in the CLI, the write erase command and the reload command erase the startup configuration and reset the unit.
    If the GUI is available, choose System Software > System Configuration. Press the Reset to Defaults button.
    Aironet 1300 Series Bridges do not have a MODE button to reset the AP to factory defaults. So, if neither the GUI or CLI is available with sufficient privileges, complete these steps to delete the current configuration and return the entire bridge settings to the factory defaults using the CLI.
    Open the CLI with a Telnet session or a connection to the bridge console port.
    Reboot the bridge by removing and reapplying power.
    Allow the bridge to boot until the command prompt appears and the bridge begins to inflate the image.
    Press ESC when you see lines that are similar to these on the CLI:
    Loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_ja.20040314"
    ...#############################################################################Note: In order to access the boot loader, you must press ESC twice. But this action depends on the terminal-emulation software that you use.
    Messages that are similar to these appear:
    Error loading "flash:/c1310-k9kw-7mx.v122_15_ja.200040314-k9w7-mx.v122_15_
    ja.20040314"
    Interrupt within 5 seconds to abort boot process.
    Boot process terminated.
    The system is unable to boot automatically. The BOOT environment variable needs to
    be set to a bootable image.
    C1310 Boot Loader (C1310-BOOT-M), Version 12.2 [BLD-v122_15-ja_throttle.20040314 100]
    bridge:At the bridge: prompt, issue the dir flash: command in order to view a directory of the Flash file system.
    The directory is similar to this directory:
    bridge: dir flash:
    Directory of flash:/
    2 -rwx 0 env_vars
    5 drwx 384 C1310-k9w7-mx.v133_15_JA.20040314
    3 -rwx 1128 config.txt
    4 -rwx 5 private-config
    3693568 bytes available (4047872 bytes used)
    bridge:Delete or rename the files config.txt and env_vars, and reboot the bridge.
    Note: Do not forget the / character before the filenames.
    bridge: delete flash:config.txt
    Are you sure you want to delete flash:/config.txt (y/n)?y
    File "flash:/config.txt" deleted
    bridge: delete flash:/env_vars
    Are you sure you want to delete "flash:/env_vars" (y/n)?y
    File "flash:/env_vars" deletedIssue the boot command in order to reboot the bridge at the bridge: prompt, or simply power cycle the bridge.
    After the bridge reboots, reconfigure the bridge with the web browser interface, the Telnet interface, or Cisco IOS Software commands.
    Note: The bridge is configured with the factory default values that include:
    The IP address, which is set to receive an IP address with DHCP. If you do not have a DHCP server, you can access the bridge using the default IP address of 10.0.0.1 using HTTP/HTTPS or Telnet. Once you gain access to the bridge via Telnet or GUI, you can modify the IP address of the bridge.
    Note: This default IP address of 10.0.0.1 becomes available only for a short period. So, make sure that you assign your own IP address to the bridge within that period of time.
    The default username and password, "Cisco".
    From this doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_password_recovery09186a00800949d0.shtml#ca_1310_ser
    One other thing, be careful with the new IOS that you aren't loading a LWAPP Recovery Image. (it almost sounds like what may have happened)
    Hope this helps!
    Rob

  • Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points

    Hi Guys,
    I would like to go for "Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points 1300". I want the AP to broadcast only 1 SSID. The client find the SSID ->put in his user credential->Raudius athentication->assign him to an specific vlan based on his groupship.
    The problem here is that I don't have a AP controller but only configurable Aironet Access Points 1300. I can connect to the radius server, but I am not sure how to confirgure the AP's port, radio port, vlan and SSID.
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
    I go through some references:
    3.5  RADIUS-Based VLAN Access Control
    As discussed earlier, each SSID is mapped to a default VLAN-ID on the wired side. The IT administrator may wish to impose back end (such as RADIUS)-based VLAN access control using 802.1X or MAC address authentication mechanisms. For example, if the WLAN is set up such that all VLANs use 802.1X and similar encryption mechanisms for WLAN user access, then a user can "hop" from one VLAN to another by simply changing the SSID and successfully authenticating to the access point (using 802.1X). This may not be preferred if the WLAN user is confined to a particular VLAN.
    There are two different ways to implement RADIUS-based VLAN access control features:
    1. RADIUS-based SSID access control: Upon successful 802.1X or MAC address authentication, the RADIUS server passes back the allowed SSID list for the WLAN user to the access point or bridge. If the user used an SSID on the allowed SSID list, then the user is allowed to associate to the WLAN. Otherwise, the user is disassociated from the access point or bridge.
    2. RADIUS-based VLAN assignment: Upon successful 802.1X or MAC address authentication, the RADIUS server assigns the user to a predetermined VLAN-ID on the wired side. The SSID used for WLAN access doesn't matter because the user is always assigned to this predetermined VLAN-ID.
    extract from: Wireless Virtual LAN Deployment Guide
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00801444a1.html
    ==============================================================
    Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller Configuration Example
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
    ==============================================================
    Controller: Wireless Domain Services Configuration
    http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c951f.shtml
    Any help on this issue is appreicated.
    Thanks.

    I'm not sure if the Autonomous APs have the option for AAA Override.  On the WLC, I can go into the BSSID, Security, Advanced, and there's a checkbox that I would check to allow a Radius server to send back the VLAN.
    I did a little research and it looks like the 1300 may give this option but instead is defined as "VLAN Override".  I've found the release notes for 12.3(7)JA5 (not sure what version you're running) that give mention and a link to configuring EAP on page 4: http://www.ciscosystems.ch/en/US/docs/wireless/access_point/1300/release/notes/o37ja5rn.pdf
    Hope this helps

  • When I turn on my computer I get the message APPLESyncNotifer.exe   Entry Point not found.

    Have a 5th generation nano and when I connect to my computer I get a message APPLESyncNotifer.exe  Entry Point Not Found. Not a computer geek so I am stumped. Anyone out there who could help? I have reinstalled ITunes and restarted my computer to not avail.

    Copying & pasting SQLIte3.dll worked out well for your computer?
    Just read your trouble with your iPod nano 5th generation & Windows PC, how about trying the one I found on this community before?
    Click the start button and type in 'msconfig' in search, and, in system structure utitily, click on the tab of 'startup' and check off the box of 'AppleSyncnotifier.exe' and reboost your system.(You have to follow down till the end of the place of the file.) That'll solve your trouble.
    I don't know you connect iPad or iPhone at all, that may change the solution? Hoping this suggestion also work out for you & your PC.

  • Error message when clicking on links from thunderbird: Firefox.exe – Entry Point Not found

    When I click on any link in a Thunderbird email message I get the error message:
    Firefox.exe – Entry Point Not found
    The procedure entry point ?DllBlocklist_Initialize@@YAXXZ could not be located in the dynamic link library T:\PQligP sFuvy (X86)\pJPpSox HneiCFv\GwCMqTQ.Oqt.
    I tried uninstalling Firefox 27 completely and reinstalling it, and the error is still there. When I uninstall V27 and install the older V26 the error disappears. Id there an issue with V27 trying to work with links from Thunderbird?
    I am on a laptop running Windows 8.1 with all current downloads.

    Thanks for the reply - as best as I can tell it seems to be some kind of incompatibility between Thunderbird V24.3.0 and Firefox V27. If I install Firefox V26 then everything works as it should. I haven't tried installing a previous version of Thunderbird to see if that makes a difference.

  • Why is my itunes not installing properly? I installed it and it was fine, then it started to show Errors. iTunes exe - Entry Point not Found. And the Error 7 (Windows error 127).Itsays to reinstall iTunes. I did that and same error. new pc, same on old

    Why is my itunes not installing properly?
    I installed itunes day before yesterday,  I spent hours last night linking all my music photograph and movie files, its a new windows 8 laptop.
    I plugged in my 64GB ipad 3 rebooted it and reloaded all the information I wanted on it, took hours... finally completed this this morning. After this I restarted the laptop to configure my icloud link for the laptop (which I installed last night while I was loading files, I chose to restart later)
    on completion I turned my laptop off for a few hours, when I turned it back on I went to itunes to connect my iphone to do the same and I got this message:
    iTunes exe - Entry Point Not Found
    The procedure entry point
    AVCFPlayerAppliesMediaSelectionCriteriaAutomaticallyKey could not
    be located in dynamiclink library F:\Programmes\iTunes.dll
                                                                                               OK
    then after pressing 'OK' the following message:
    iTunes
    iTunes was not installed correctly. Please reinstall iTunes
    Error 7 (Windows error 127)
    I went back to apple website to reinstall iTunes, first reinstalled it same again, then unsinstalled it and the reinstalled it, same again.
    The same thing happened with my old lap top and I replaced it with this new one at the start of the week.
    Has anyone any idea what is going on and how to rectify this problem, I am now going on 3 weeks without iTunes.
    Regards,
    Damian36

    I started up and plugged in my iPad  and then the following message came up:
           iTunes
    ❗️This iPad cannot be used because the required software is not
        Installed. Run the iTunes installer to remove iTunes, then install
        the 64-bit version of iTunes.
                                                                                             OK
    I then proceeded to the "iTunes64Setup" expanded folder to load "AppleMobileDeviceSupport64"
    Started the install and then received this message:
          Apple Mobile Device Support
    ❗️Service 'AppleMobile Device' (Apple Mobile Device)
        failed to start. Verify that you have sufficient
        Privileges to start system services.
       Abort.               Retry.                Ignore
    I tried all tree options, last being ignore.
    I continued to download the other 2 you suggested with out any drama.
    I did a system restart and then opened iTunes.
    Connected my iPad
    Then message appears:
          iTunes .exe - System Error
    ❌ The program can't start because CoreAdioToolbox.dll is missing from
          Your computer. Try reinstalling the program to fix the problem.
                                                                                           OK
    Press OK and then the next message:
           iTunes
    ❌ iTunes was not installed correctly. Please reinstall iTunes.
          Error 7 (Windows error 126)
                                                                                           OK
    Any suggestions?

  • Crystal Reports 2008-Vista-ERROR-crw32.exe Entry Point Not Found in dll

    Hi Experts,
    I just installed the Crystal Reports 2008 (with SP0) on my Vista (Home) machine.  When I try to start the CR 2008, I am getting the below error message:
    Error Title: crw32.exe - Entry Point Not Found
    Error Message: The procedure entry point ?PrintLegend@CMapXLegend@CSLib300@@QAEXJJJJJ@Z could not be located in the dynamic link library cslibu-3-0.dll
    Here are the things I tried to resolve the above problem:
    1) Uninstall and Reinstall the CR 2008.  -  No change.
    2) I configured the DEP to accept Crystal Reports (Performance - Advanced - DEP allow). 
    None of these seem fix the problem. 
    Can you please help me kick start the Crystal Reports 2008? 
    Thanks,
    Arun

    Please try with this:
    Run a command prompt as administrator. From the start menu, select "All Programs", then "Accessories" and right-click on the "Command Prompt" shortcut and choose "Run As Administrator". From here you can use the following command to disable Data Execution Prevention (DEP) with the following command:
    bcdedit.exe /set nx AlwaysOff
    Keeping your command prompt open, run your setup or other process being stopped by DEP. Then, to turn it back on again, do the same and run the following:
    bcdedit.exe /set nx AlwaysOn
    Regards,
    Shweta

  • When I connect my new ipod nano to my laptop (using windows)I get an error message saying "itunes.exe - entry point not found" I cannot access my itunes , or download a new version. Any ideas what to do or what is causing this?

    I have been given a new ipod nano to replace my much loved but old ipod. When I plug it into my laptop to sync it I get an error message stating "itunes.exe - entry point not found. The procedure entry point AVCFAAssetCreateWithByteStreanAndOptions could not be located in the dynamic link library
    AVFoundationCF.dll" I cannot acces my itunes or download a new versiona as this keeps flashing up. Any ideas? Please help, my life is meaningless without my music!!

    Also I now can`t access any of my itunes library and am concerned that if I remove it from my computer I will lose everything as I have no option of accessing and therefore backing anything up. Any ideas?

  • I see a AppleSyncNotifier.exe - Entry Point Not Found error when my PC starts.

    when booting up my computer, even before I try to bring up itunes, I get the following error message:
    AppleSyncNotifier.exe - Entry Point Not Found
    the procedure entry point ___cfconstantstringclassreference could not be located in the dynamic link library core foundation.dll
    But once I click off the message, everything seems to work fine.
    how can I correct this problem?
    2 IPod 5.1.1
    1 IPad 2 wifi
    Windows Vista 32

    Try here >  http://www.pchelpforum.com/xf/threads/applesyncnotifier-exe-entry-point-not-foun d.124298/

  • TNS Listener: Entry Point Not Found

    First I installed 8.1.6 Personal edition
    on my laptop (NT4 SP5):
    Folder: d:\orant.
    Oracle Home: DEFAULT_HOME
    That went fine. I could connect to the database with SQLPLUS, DBA etc.
    Then I tried to install Portal using:
    Folder: d:\9iAS
    Oracle Home: iSuites
    Spent three days trying to get Portal to install ok. Have finally got through the installation of 9iAS (HTTP Server Only), which the Universal Installer claims to be successfull.
    Started the Apache Server and tried to connect to the portal. I get the following error message:
    Proxy log On failed.
    Please verify that you have specified correct connectivity information i.e.username, password & connect-string in the Database Access Descriptor
    Error-Code:12154
    Error TimeStamp:Tue, 23 Jan 2001 23:20:00 GMT
    Database Log In Failed
    TNS could not resolve service name
    Verify that the TNS name in the connectstring entry of the DAD for this URL is valid.
    I can access the admin page:
    http://<machine>:80/pls/admin_/
    To debug this I tried to connect to the database with SQLPLUS and I got this error message:
    I:\>sqlplus
    SQL*Plus: Release 8.1.7.0.0 - Production on Tue Jan 23 16:08:58 2001
    (c) Copyright 2000 Oracle Corporation. All rights reserved.
    Enter user-name: system
    Enter password:
    ERROR:
    ORA-12560: TNS:protocol adapter error
    Enter user-name:
    Checked my Services and found that the TNS listener was not started. When I try to start the OracleDEFAULT_HOMETNSListener in my Services I get the following error message:
    TNSLSNR.exe - Entry Point Not Found
    The procedure entry point snlpcgtsrvbynm could not be located in the dynamic link library oranl8.dll.
    I have tried swicthing my primary Oracle Home using the Home Selector. Did not help.
    Shouldn't the TNS listener be started, or?
    Any ideas what to check?

    I have found the solution of my problem from Oracle9i Portal's Configuration Guide , the troubleshooting part. The document can be found in the Oralce9i Documentation web site.
    The problem is that I set the incorrect information in my tnsnames.ora file when installing Oracle9i Portal.
    The solution is set the host name, port number and SID in the tnsnames.ora file. This file is located at
    \Oracle_Home\network\admin\
    Here is the example of the content in that file:
    PORTALDB_MyHost =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = MyHost)(PORT = 1521))
    (CONNECT_DATA = (SID = PortalDB)(SERVER = DEDICATED))
    INST1_HTTP =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = TCP)(HOST = MyHost)(PORT = 1521))
    (CONNECT_DATA = (SERVER = SHARED)(SERVICE_NAME = PortalDB)(PRESENTATION = http://admin))
    EXTPROC_CONNECTION_DATA =
    (DESCRIPTION =
    (ADDRESS_LIST =
    (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC0))
    (CONNECT_DATA = (SID = PLSExtProc)(PRESENTATION = RO))
    ---------------------------------------------

  • Satellite P300: BSOD error STOP: c0000139 {entry point not found}

    I've been having this error for a few weeks on my Toshiba P300.
    When I start my notebook there appears a blue screen with an error for a split of a second:
    STOP: c0000139 {entry point not found}
    The procedure entry point ntoskrnl.ExiAcquireFastMutex could not be located in the dynamic link library Hal.dll.
    Then Windows Vista starts normal.
    I don't get this error when i start the computer from hibernate. What does this error mean??
    I also have problems with my integrated webcam. I get the message: 'locked by another application'. I already reinstalled the software I downloaded from the website, but that didn't help. Does the error have something to do with the webcam that doenst work properly??

    I dont know what the problem can be but you should use system restore tool and rollback OS to earlier time before this error message started.
    About webcam issue please visit http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=131308

  • Apple Software Update error- "Entry Point not found"

    I have had Apple Software Update/ iTunes on my PC for over 4 years. Today, randomly, when I went to update iTunes to the new 10.5 version, Software Update did not prompt me to update. That was odd, but I didn't realize anything was amiss yet at this point.
    In iTunes, I went Help > Check for Updates which indicated the new version was downloaded. When promted whether I'd like to update, I hit yes, which even more oddly took me to apple.com to download iTunes all over again. (Normally, updates download from within iTunes and it's an update, not a full hour-long re-download.)
    I didn't want to redownload iTunes (what would happen to all of my previously downloaded apps and music, set playlists?) so I opened Software Update, and got the following error message:
    SoftwareUpdate.exe - Entry Point Not Found
    The procedure entry point ?CreateProductsFromXML@CSUCatalogObject@@QAEXP6AIPAXIIJ@ZOIV?@CStringT@WV?$StrT raitMFC@WV?ChTraitsCRT@W@ATL@@@@@ATL@@@Z could not be located in the dynamic link library SoftwareUpdateFiles.dll
    Strange, right?
    So my questions.
    1.) Does anyone know why Apple Software Update would suddenly get errors? I've used it recently (this past weekend?) and everything was fine.
    2.) Is there a way to fix Software Update, since I'll surely need it in the future.
    3.) In the meantime, should I proceed with re-downloading the full version of iTunes again, and will it mess up anything I currently have in my iTunes library? Would I need to back it up or do anything to help ensure there are no further problems?
    Thanks for your help. To say I'm confused is an understatement!

    Well... after I posted this, some info from other posts came up and I found the answer!
    In case anyone has the same issue that runs across this... this worked for me perfectly.
    Correct Answer by Sposivo  on Aug 19, 2011 5:23 PM
    "Start, Control Panel, Add & Remove Programs, Apple Software Update, Change, Repair"  - this fixed it for me.
    See the answer in context

  • Help! Another "Entry Point Not Found" Error

    Hello,
    I purchased iPhone 4 earlier this week and went to synch it last night. Apple Updates updated and crashed several times, now iTunes won't even start. I already had it set up for my iPod, my iPad, and a prior iPhone, so just plugged my new iPhone in and went to town. iTunes did update all my apps before I used Apple Update. I was trying to get the OS updates for both my iPhone and iPad, but now it doesn't work. I tried downloading iTunes again and running the fix and it didn't work. I am runing Windows 7 64-bit.
    Here is my error message:
    iTunes.exe - Entry Point Not Found
    The procedure entry point
    kCMByteStreamNotification_AvailableLengthChanged could not be
    located in the dynamic link library CoreMedia.dll
    Then a second dialog box pops up that says:
    iTunes
    Itunes was not installed correctly. Please reinstall iTunes.
    Error 7 (Windows error 127)
    Please help!
    Thanks, Sean

    Hi vladdy007,
    Please upgrade your OS to Win XP SP3. This would fix the problem. The minimum spec for running AI CS6 is Win XP SP3.
    Thanks and Regards,
    Nishant Kumar Thakur

Maybe you are looking for