Aironet 1310 bridge does not reestablish connection

We have an aironet 1310 bridge installed (root/non root) where the non root drops sometimes the signal when the morning sun is in direct line with the link. This blackout problem is known. What bothers me is the fact that the bridge does not automatically reestablish the association...
Once it has been lost we have to restart the Air 1310, then it re-associates. Is there a workaround or an automatism?
Thank you for your suggestions.
Bert

This should be automatic. I had a client have this problem once, and we found that the problem was actually with the 1310 being configured in diversity mode. The 1310 would disconnect in tough weather conditions and try to connect to the little metal stub that comes on the bridge. The signal was too weak to establish a good connection, but for some reason it would not switch back.
So check to see if you have diversity mode enable, and disable it if it is. If that's not the problem, I'm not sure what it could be. Have you tried upgrading the IOS?

Similar Messages

  • Aironet 1310 Bridges keep losing connection

    There was a similar thread about this last year and I tried what was listed in there to no avail.  I have 2 Aironet 1310 bridges, one as a route bridge and the second as a non-route with clients.  These worked great for nearly a year, we had no problems keeping the connection up.  They were not connected for the last few months but nothing was changed on the configuration, when I put them back up they reconnected just fine and worked for about an hour, not they randomly disconnect with the same message in the log entries below.  Is there something wrong with them now?  The are using the same antennas as before and are in the same exact locations.
    logs from root bridge
    Nov 29 13:52:53.311: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the client
    Nov 29 13:52:53.311: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer valid
    Nov 29 13:52:53.568: %DOT11-6-ASSOC: Interface Dot11Radio0, Station Test XXX.XXXX.XXXX Reassociated KEY_MGMT[WPAv2 PSK]
    Nov 29 13:55:16.260: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the client
    Nov 29 13:55:16.260: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station XXXX.XXXX.XXXX Reason: Previous authentication no longer valid
    Nov 29 13:55:16.550: %DOT11-4-MAXRETRIES: Packet to client XXXX.XXXX.XXXX reached max retries, removing the client
    Nov 29 13:55:16.550: Client XXXX.XXXX.XXXX failed: reached maximum retries
    logs from non-root
    Nov 29 2010 13:52:55: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Received deauthenticate (2) not valid
    Nov 29 2010 13:52:55: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to down

    I am not at the remote location any more, but the route bridge had a signal of -78 dB and a SNR of -22 dB.  The non-route has -77dB for signal and a SNR of -22 dB.  The location has line of sight, over water with nothing in the way. 
    Since I last posted I changed the fragmentation and RTS thresholds back to default from 4000 and it has been up for 24 hours now.  I am hoping that it has made the difference.

  • Configuration of a Point to MultiPoint link with Cisco Aironet 1310 bridges

    Hi All,
    The previous problem of which I started another conversation here:
    http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddba023
    somehow dissapeared. It could have been a problem of interferences.
    I have another issue with other (multipoint) wireless WAN link, which I hope has a solution.
    On the central node, we have an Cisco Aironet 1310 bridge configured as root-bridge. It has a panel of four vertical polarity 17 dBi panel 90? antennas, with more than enough gain (there is a 250 mWatts 802.11 b/g amplifier, before the 4-way splitter) and excellent line of sight to three remote bridges.
    The three (03) remote bridges are also Aironet 1310 models, confidured as non-root-bridges.
    The problem we have is that it seems that when the three remote links operate concurrently the amount of lost packets is huge. When I shutdown the radio interfaces of two bridges, the remaining bridge makes an excellent link with the central node.
    It seems that some hours are more critical than others, also the links operate much worse when there is some (small) network traffic in them.
    I have read the 1310 manuals, and I can't find a sample configuration for point to multi-point links.
    Does someone knows what radio interface configuration should I need to use to establish better quality communication?
    I mean, perhaps the 1 x root - 3 x no root configuration is not recommendable for the multipoint link configuration.
    Any hints will be welcome.
    Best Regards,
    Igor Sotelo.

    Hi All,
    Thank you for the information. I configured the distance on the root bridges, but the links showed instability.
    I'm using a bi-directional amplifier. It has two pieces. According to the manuals, one is installed indoors, the other outdoors. I'm not sure if the indoors piece has the transmition module or it's only the injector.
    We could establish connection at 7 km (around 4 milles) distance from the central point, using 24 dBi antennas on the other side.
    However, we have issues with a near located point that is only 1.2 Km (around 0.8 milles) away and has a 13 dBi integrated patch antenna. The signal strenght value we get there is in the -62 to -68 dBm range, and is noticiably (5-10 dBm) lower than the strenght we get at other points of the link. And I have trouble establishing a high quality link with that point, using OFDM modulation. I tend to think that if I remove the amplifier I'm not going to reach that point at all. The EIRP on the central iste is 34 dBm / 2.5 watts, without amplifier it would be 26 dBm / 0.4 watts.
    On the opposite sites the EIRP is 33 dBm / 2 watts using CCK or 28 dBm / 0.63 watts using OFDM.
    When one looks at the central site from that point, an Motorola Canopy with passive reflector (EIRP 48 dBm or around 64 watts) can be seen. It doesn't have the same direction, but the opposite site must be large distance and could interfere with my wireless network. Attached is an amplified photo of the view. It's safe to assume that the Canopy operates in the 2.4 GHz frequency range.
    Once I connect the point at 1.2 Km, the multipoint link loses its quality, and soon the lost packets get too frequent.
    The CCK seems to be much more interfered than OFDM, I guess because of that canopies.
    Another thing I'm wondering about is if the Aironet 1310 can continuosly switch CCK-OFDM over the same point - multipoint link, without losing packets.
    What other parameters should I tweak? Is there a way to avoid interferences fromt the canopy?
    I would like to apply 100 mWatts local power using the radio with OFDM, but it seems that's not possible.
    Best Regards,
    Igor Sotelo.

  • JDBC-ODBC Bridge does not support Unicode UTF-16

    Hi
    I'm using Jdeveloper 10.0.3 IDE in order to develop an application for data transformation between MS Access 2003 (source) and Oracle 10g (destination). Clients use Windows XP.
    JDBC-ODBC Bridge still does not support Unicode UTF-16 which is the Charest used by MS Access 2000/2003.
    Note that when I changed locale in regional setting, destination Connection to Ora10g failed to open a connection, it works only with English locale, so I can't change my locale information.
    How can I read Unicode from source DB?
    Any help would be appreciated. I look forward to see your response.
    Thanks,

    i also heared that JDBC-ODBC Bridge still does not support Unicode UTF-16,
    but i guess this is not in my case.That's the key in fact. JDBC-ODBC Bridge does not support UTF-16, which is the charset used by MS Access 2000/2003.
    or do i need to use a third party driver for jdbc odbc bridge?Free library at http://jackcess.sourceforge.net/
    Commerical JDBC driver at http://www.hxtt.com/access.html
    Yonghong Zhao
    System Analyst
    www.hxtt.com

  • When I place a dvd in and click the Br download images Bridge does not come up.

    When I place a dvd in and click the Br download images Bridge does not come up.

    When in DFU mode and connected to the computer iTunes does not say anything but iTunes will see the iPod and you can restore the iPod via iTunes. When in recovery mode and you connect, iTunes will say it found an iPod in recovery mode.

  • Bridge Does Not Automatically Bring Up Photoshop When the Photo is Double-Clicked

    I have just purchased CS4 with Bridge for my new MacIntosh.  In Bridge for the PC, when I double click a photo it automatically brings up Photoshop.  On the Mac version, it gives me an error message saying that part of the application is not loaded.  I completely uninstalled the program, and reloaded the application and still get the same message.  So in Bridge on the Mac, to get around this, I right click the picture and go to "Open With" and there are two entries:  "Open with CS4 (default)" and "Open with CS4."  This works if I pick either option.  My Windows version only has "Open with CS4 (default)" as the option.
    I called Adobe support (in India?) with no solution.
    I really like the double click option rather that using the pop-out menu choice.  What is wrong with the Mac install, and how can I fix this issue?

    Thank you for your help.  I updated the software and it "healed" itself.
    Best regards,
    Gregory T. Stramat
    [email protected]
    801-978-4735 (Office - Preferred)
    801-652-0775 (Mobile)
    Omke Oudeman <[email protected]>
    01/22/2010 12:52 AM
    Please respond to
    [email protected]
    To
    Gregory Stramat <[email protected]>
    cc
    Subject
    Bridge Does Not Automatically Bring Up Photoshop When
    the Photo is Double-Clicked
    This might mean that you have either 2 installs of CS4 (one on an other
    disk?) or you did not use the the default application folder on root level
    but have it installed in the user account application folder. Could you
    check this?
    and go to "Open With" and there are two entries:

  • Iphone 4 does not stay connected to my network

    Since upgrading to 6.1, my iPhone 4 does not stay connected to my network.  I have to input my password each time I leave my house.  My other devices stay connected, so the issue is with the upgrade.  Has anyone found a way to keep their IPhone connected to their network?  Thanks.

    I don't have another phone to try. I took out the sim to check for deffects but it looked fine. Cleaned the sim card with alcohol and cleaned the aim compartment. Phone didn't loose Internet connection all day yesterday, but this morning went to check emails and wouldn't update until I turned airplane mode on then off again.

  • Iphone does not stay connected to wi-fi.

    When using apps or when in sleep mode my iphone does not stay connected to my wi-fi. All other items within the house have no issues with staying connected to my wi-fi.

    By design, when entering sleep mode, the iPhone will disconnect from WiFi to conserve battery. If you want the WiFi connection to remain persistent, plug your phone into a power source.

  • Adobe Lightroom, Photoshop and Bridge does not recognize the raw files from my Canon Mark III 5D Camera.

    Adobe Lightroom, Photoshop and Bridge does not recognize the raw files from my new Canon Mark III 5D Camera.  How can I get my files open to view and edit?  I am using LR3, Photoshop CS3 and Bridge CS3.  Do I need to upgrade these programs or is there another way to get these programs to recognize my files?
    When I try opening the raw images in Lightroom, the thumbnails say "Preview unavailable for this file"  ... when I click "import" an error message pops up that says "The files are from a camera which is not recognized by the raw format support in Lightroom."
    When I try opening the raw images in Photoshop, an error message pops up saying "could not complete your request because photoshop does not recognize this type of file."
    When I try opening the raw images in Bridge, it just shows an icon with the file name and CR2.
    Please help!!!

    Unless I missed an announcement, today, LR6 isn't available, yet, right?  Only Adobe employees and beta testers would know what LR6 does differently at this point and they're all sworn to secrecy.
    LR5 is available as a standalone version.
    PS-CS6 is available as a serial-number-licensed version.
    PS-CC + LR5 are also available as a Photography Plan subscription for $10/month with a minimum OS versions of OSX 10.7 (and probably 10.8, soon) and Windows 7.
    Bridge is part of PS, not a separate program.
    LR5 standalone and LR+PS-CC plan are both available on this page:  http://www.adobe.com/products/catalog/software.html
    PS-CS6 can be found on this page:  Creative Suite 6 which can be found by searching www.adobe.com for Photoshop CS6 and clicking the Buy link in the on-the-fly search results.
    As with any new Adobe software, it might be wise to run it in trial mode for a few days/weeks to see if it works well with your computer, before purchasing and finding out you might need a new computer, first.

  • IPad (3rd generation) does not automatically connect to wi-fi.

    iPad (3rd generation) does not automatically connect to wi-fi.  It is fully updated to 5.1.1 but you have to manually connect after turning off and back on.  I also have an iPad 2 with the same OS but it automatically connects.  The wi-fi has no security. 

    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Adobe Bridge does not accept the NEF files from my new Nikon D800. I use the latest version, there a

    Adobe Bridge does not accept the NEF files from my new Nikon D800. I use the latest version, there are no updates

    Hi,
    CS6
    Van: R_Kelly [email protected]
    Verzonden: maandag 16 september 2013 18:42
    Aan: Hans van Sloten
    Onderwerp: Adobe Bridge does not accept the NEF files from my new Nikon D800. I use the latest version, there a
    Re: Adobe Bridge does not accept the NEF files from my new Nikon D800. I use the latest version, there a
    created by R_Kelly <http://forums.adobe.com/people/R_Kelly>  in Photoshop for Beginners - View the full discussion <http://forums.adobe.com/message/5686078#5686078

  • I am running a TRIAL VERSION of Adobe Photoshop CS6 Extended and Bridge does not open.  Help?

    I am running a TRIAL VERSION of Adobe Photoshop CS6 Extended on MAC and Bridge does not open.  It did open when I first downloaded it - but now a black question mark is over the BR icon and it does not open up.  Any ideas from anyone? 

    Hi Steve -
    I just thought it was interesting and helpful to me to learn that the icon for Bridge does not appear anywhere.  Not in Application Folder.  Not in the Finders Directory Files.  I see your point - if I could locate that icon - I'd be set by dragging it onto my DOCK and launching it from there. 
    So - I'm assuming I need to uninstall CS6.   Please list all the steps for me to uninstall so that I don't miss any CS6 files. 
    When I search in FINDER for CS6 uninstall- I see two icons -  red adobe "UNINSTALL ADOBE PHOTOSHOP CS6" (both files are identical)  Under KIND they both say Alias - with two different dates they were last opened (in November - few minutes apart).  Is that what I use to uninstall completely all the files related to PS CS6 Extended as well as Bridge? 
    Do I need to DEACTIVATE ANYTHING ANYWHERE? 
    DOES ANYTHING NEED TO GO INTO TRASH. 
    I just want to make sure 'everything' related to CS6 Extended is off my computer and out of all the files.  In the event i want to re-install - naturally I don't want to run into any conflicting 'issues'.
    Do you think if I reinstall I will run into this same problem again (BR not launching)?  Is there anything I can do to prevent it?  I note on the forums - going a few years back - that there have been a lot of issues related to this same problem - even in other versions of the Creative Suite.  Is Adobe doing anything to rectify this problem for us Photoshop CS Suite lovers or is all their focus just going into CC? 
    Thank you so much for trying to help me resolve this issue.  It is very frustrating to have an Adobe product that is not completely functional.  Especially when the Creative Suites are so expensive.  I appreciate all the time you've put into this issue. 
    Carole

  • Mini Bridge does not open in InDesign after installing 8.0.2 upgrade

    This question was previously posted in the InDesign forum (http://forums.adobe.com/message/5833991#5833991), but it was suggested that I should cross post it here.
    I installed InDesign CS6 upgrade 8.0.2.  Now I cannot open Mini Bridge.
    If Bridge is not already open,
         - selecting File | Browse in Bridge...  or clicking on the Bridge button: Bridge opens - good!
         - control-click on the Bridge button: I get a Reset Settings error dialog - NOT good!  I cancelled this and Bridge opened fullscreen okay.
         - alt-click on the Bridge button: Two Bridge applications opened fullscreen! - NOT good!
         - shift-click on the Bridge button: Bridge opens, but Mini Bridge does not! - NOT good!
    If Bridge is already open,
         - selecting File | Browse in Bridge... or clicking on the Bridge button: the ruler bars dim and nothing else happens! - NOT good!
         - control-click on the Bridge button: Bridge opens maximized! - good!
         - alt-click on the Bridge button: the already opened Bridge, plus a new Bridge, both open! - is this normal?
         - shift-click on the Bridge button: the ruler bars dim and Mini Bridge does not open! - NOT good!
    I have tried resetting the preferences in Bridge and rebooted after doing so.
    My main concern is that I cannot get Mini Bridge to open at all.  I can ignore the other problems mentioned above, if I can just get Mini Bridge to open.
    This problem does not exist in Photoshop CS6.
    I have restored my C: drive from backup twice and tried the upgrade a total of three times.  The results are the same each time.
    Does anyone have any idea what is causing my problem and how I might correct it?  I am running 64-bit Windows 7 Professional SP1, 3.40 GHz Intel Core i7-3770 CPU, 32.0 GB installed memory.

    Sorry to hear that, forgot to mention the resetting of preferences in InDesign.
    Have you also tried that (ctrlAltShift while starting ID)?
    I'm afraid I have not really more ideas and I am a Mac user and don't know anything relevant about Windows.
    And ultimate you have of course the option to reinstall CS6 after an official uninstall in combination with the Adobe Clean Tool. But before doing so read all instructions and have a proper back up of all relevant customized settings, workspaces etc.
    http://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html

  • Bridge CS6 bug: closing Bridge does NOT end process

    Bridge does NOT started at boot. 
    Windows 7 -64 (all current updates). 
    Photoshop CS6 13.0 extended
    Bridge 5.0.0 399x64
    After closing Bridge by clicking on the Close X or file/exit, the process 'bridge.exe' does not terminate and therefore thereafter trying to restart bridge fails. 
    Have to open up Task Manager, kill the bridge.exe process, in order to restart bridge.
    The bug is so variable that just when it appears repeatable, something changes.
    Any idea of what to look for?

    This is NOT TRUE.  "FYI:  In Windows, to exit a program/application, clicking the Close button in the upper-right corner of the program window is the same as using the File menu, and click Exit."
    If you click the red X you close the window and force close of the program.  Any changes you made to program will not be saved if you have the option "start Bridge at login" checked.   If you click File>Exit the program will go through the procedure to normally close down, and any changes you made will be saved. 
    I tried to follow your steps but was confused on steps 3,4,5,8,10.
    I used 1,2,3,7,9,11.  Bridge was closed.  Perhaps with all your "browse to bridge you are opening multiple copies?
    Hey, how about trying and commenting on my problem with the Find function in CS6?  http://forums.adobe.com/thread/1007726?tstart=0

  • Acrobat does not allow connection to

    Need help with this error message please.  Using Win7, saved a Word 2010 table of contents with multiple links to pdf files across internal servers as a PDF.  Also created the word doc w/multiple pdf links as a PDF file using acrobat9 standard and have same problems.   when a user with Adobe Reader 8+ clicks on a pdf link in the PDF table of contents file, they get an error message Acrobat does not allow connection to:   and they cannot open the linked file.  However, I am able to open the files using the same links with both reader and acrobat.   
    This worked previously until we upgraded to these versions of software... the error message shows a number of % signs and multiple ////.  However, i can open the fiile but others cannot.
    anyone have any ideas or is this a fix that i need to download?  

    not sure where my previous reply went; however, there are numerous machines at varuious sites that will be accessing this server/folder.  I am not sure if it is a trusted sites issue as the file lists numerous PDF links and some of them open to the respective pdf file and others recieve the mssage.  All the files reside on the same server within the same main folder and within subfolders.  never had the problem before.  the users can open some of the linked files and others the connection msg appears.  I however, am able to open the same links they get the error on.  I am totally baffled by this and have been troubleshooting for weeks now.  I just had acrobat X installed to see if that would help but still problem.  I also saved the word doc (2010) as pdf (which lists the links to the other pdfs) but users still have same problem.  there are approx 75 links within this doc and I truly hope we don't have to relink everything..

Maybe you are looking for