Aironet 1530 AP with Wireless Controller
The Aironet1530 AP datasheet suggests that it can be deployed as part of a lightweight controller based arrangement, but it does not appear as a supported AP on any of the controller s/w release notes that I've sio far looked at, could anyone advise?
Regards, Dave Gabb
v7.5 is suppose to have support for the newer AP models. You would have to wait for the documentation to come out which will have more info.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"
Similar Messages
-
Help with wireless controller and VLANs
Hi I'm trying to setup a wireless controller in preparation for a large site go live later this year. I'm struggling to get the controller and the WLAN using the correct VLAN. I want the controller on VLAN 100 and the clients on the WLAN on VLAN 200.
My thought is that I would need a config similar to:
Switchport for wireless controller management port set to trunk VLAN 100 and 200 with no native VLAN set.
The management interface on the controller set to VLAN 100.
A dynamic interface created on VLAN 200.
When setup like this I can get to the controller on its management address but only from VLAN100 not from another VLAN on site or from other sites over the WAN.
I have setup a WLAN which is set to use the dynamic interface on VLAN 200.
I have set the AP to use HREAP and set the native VLAN as 200 and added the dynamic interface into the VLAN mappings
When I connecting a client to the WLAN I get an address on VLAN 100.
The switchport for the AP is set to native VLAN 100 and trunk 200 – this setup works for standalone APs at other sites.
What am I missing?
Also any idea why the management interface address is not routing? The netmask and gateway are set correctly.
Thanks
PaulJust to add to Steve's post... You only need to create a dynamic interface for vlan 200 if you have ap's also in local mode. If your ap's are in H-REAP/FlexConnect mode, you don't need a dynamic interface for vlan 200.
In you H-REAP/FlexConnect ap, you would set the wlan to vlan mapping there and the switchport configuration would be a trunk allowing vlan 100 (im assuming your native vlan for your ap) and vlan 200. You should see something like the following:
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Cisco Aironet 3502i and Virtual Wireless Controller- Question
Hello everyone,
As soon, I purchased two Cisco 3502i and Cisco 1142 however, two issue are that I don't have controller and smartnet. As my purpose, it using for Home Use but house with 2,500 Sq ft with two floor and new 24x24ft garage with two floor. I put two Cisco 3502i for garage and one cisco 1142 in house on second floor. Separated for multi media, gaming, streaming high resolution video, parts, and downloads programmings online. It will run with Cisco Catalyst Express 500 with 24 ports (4 POE) and two gigabit ports. In house, it have Dell Poweredge 2850, Cisco Catalyst Express 500 with 24 ports POE and 2 ports gigabit.
I thought to make my own developing with my first time using Wireless Controller. I wanted to try out with Virtual WLC on Dell Poweredge 2850 running ESXi 4.1.
Specs for Dell Poweredge 2850:
- 2x Intel Xeon Dual Core 3.8 GHz
- 4GB RAM (Will upgrade to 12GB soon)
- 2x 146GB and 2x 36GB SCSI
- 2x 1 Gbps built in and 4x 1 Gbps PCI-X
Developing with Untangle and pfSense to make it support with LADP and VLAN to both Cisco Express 500 using 4 gbps PCI-X. I have read the requipment list to use Virtual WLC but it seem met the requipment for my 2850. If someone offer me to get Virtual WLC and IOS from their, I accept to "borrow" it. I do go college which is Rochester Institute of Technology at New York and my major is Applied Computer Technology. I live here at Hampton Road, Virginia. Just in case if you might know about RIT. I just start to learning myself with Cisco books.
I have a question:
- Is there possible to get trial or full version of Virtual WLC?
- Is there possible to get Lightweight or Autonomous IOS for Cisco 1142 and 3502i?
- Does it supported Dell PowerEdge 2850?
- Does 3502i support Autonomous? (Not actually but I have researched around online about that it will work with 1262's IOS)
Thanks
GageAnswers in-line...
I have a question:
- Is there possible to get trial or full version of Virtual WLC?
No. You will need a SmartNet contract (or a freshly purchased device) to obtain software from cisco. Nobody will provide this to you.
- Is there possible to get Lightweight or Autonomous IOS for Cisco 1142 and 3502i?
No. You will need a SmartNet contract (or a freshly purchased device) to obtain software from cisco.
Nobody will provide this to you.
- Does it supported Dell PowerEdge 2850?
Cisco doesn't go in to great detail regarding the actual Hardware requirements of the vWLC (as far as ESX Host requirements). Primarily, making sure you are running ESX 4.x/5.x is necessary. The vWLC provisions 2Gb of RAM and 8GB of thick provisioned storage, so if your host can accomodate I don't see any reason it wouldn't work.
- Does 3502i support Autonomous? (Not actually but I have researched around online about that it will work with 1262's IOS)
Yes, with the latest versions of IOS 15.2(2)JB, full functionality in autonomous can be achieved on the 1550, 3500, and 3600 series APs
http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/15.2_2_JB.html#wp355587 -
Fujitzu/Siemens v8210 laptops bluescreen with Wireless Controller 4.2.61.0
I have noticed a problem with Wireless LAN Controller version 4.2.61.0. This version causes a blue screen with Fujitzu Siemens v8210 laptops with driver atheros ar5006eg driver version 4.1.2.111 sia installed.
Other make and model of laptops work fine with the controller such as Dell and IBM etc.
The atheros manufacturers website has a later driver than the fujitsu website which clears the fault, once you install the new driver on the laptop.
Has anyone else had this problem and would you reccomend to downgrade the Wireless LAN controller to a previous firmware release, as the bug toolkit and caveats for the controller release did not highlight this problem?Hi Carl,
Your LAPs joins the wrong WLC even when you've configured the primary/secondary controllers name OR IP address and you are using v4.2.61.0. Is this correct?
If so, then it's a well-known bug of the v4.x. Unfortunately, the workaround is CLI. It's unfortunate because you have to type the command on the WLC and specify the LAP.
The command is: config ap controller primary
This bug has been fixed on the 5.X and 6.X firmware.
Hope this helps. -
Error in GUI of Cisco 3850 Switch with Wireless Controller.
Hi,
I have Configured 3850 switch wireless controller. But while accessing the controller through GUI, I faced following errors while configuring it through GUI.
Because its complecated to configure it through CLI.
Attached are the snaps of error faced.
and if I didnt get this error, and able to configure, I can save it because of this error.
Please help me on this issue, so that I can easily configure the controller.
Brgds,
Ninad ThakareHi Sandeep,
Here is the configuration which I have did.
ip http server
ip http secure-server
wsma agent exec
profile httplistener
profile httpslistener
wsma agent config
profile httplistener
profile httpslistener
wsma agent filesys
profile httplistener
profile httpslistener
wsma agent notify
profile httplistener
profile httpslistener
wsma profile listener httplistener
transport http
wsma profile listener httpslistener
transport https
wireless mobility controller
wireless management interface Vlan4 ( Voice VLAN )
wlan FG-WiFi 1 FG-WiFi
client vlan 4
ip dhcp server 10.106.72.1
no security wpa akm dot1x
security wpa akm psk set-key ascii 0 testing1234
no security wpa wpa2
no security wpa wpa2 ciphers aes
no wmm
no shutdown
wlan GLOBALACCESSII 2 GLOBALACCESSII
client vlan 4
ip dhcp server 10.106.72.1
no security wpa akm dot1x
security wpa akm psk set-key ascii 0 testing1234
no security wpa wpa2
no security wpa wpa2 ciphers aes
no wmm
no shutdown
ap group default-group
ap group 3850WLC
wlan FG-WiFi
vlan 4
wlan GLOBALACCESSII
vlan 4
end
Brgds,
Ninad Thakare -
Hi!
I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...
I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).
Log from AP:
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x00000184
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialize
PCIEx: initialization done
flashfs[0]: 6 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 2369024
flashfs[0]: Bytes available: 30016000
flashfs[0]: flashfs fsck took 21 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 44:2b:03:dc:09:25
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################
File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x4000
executing...
enet halted
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32126976
flashfs[1]: Bytes used: 2369024
flashfs[1]: Bytes available: 29757952
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1041N-E-K9 (PowerPC405ex) processor (revision B0) with 98294K/32
768K bytes of memory.
Processor board ID FCZ1611W414
PowerPC405ex CPU at 333Mhz, revision number 0x147E
Last reset from reload
LWAPP image version 7.0.94.21
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:2B:03:DC:09:25
Part Number : 73-14034-04
PCA Assembly Number : 800-34273-05
PCA Revision Number : A0
PCB Serial Number : FOC16075VZ3
Top Assembly Part Number : 800-34284-03
Top Assembly Serial Number : FCZ1611W414
Top Revision Number : A0
Product/Model Number : AIR-LAP1041N-E-K9
% Please define a domain-name first.
Press RETURN to get started!
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:09.574: *** CRASH_LOG = YES
Base Ethernet MAC address: 44:2B:03:DC:09:25
*Mar 1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
(contains, 1024 messages)
*Mar 1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:11.892: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
*Mar 1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
logging facility kern
^
% Invalid input detected at '^' marker.
*Mar 1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS
IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)
*Mar 1 00:09:08.282: -Verify the required power-injector is installed on this
port: AIR-CT5508-K9(Gig 0/0/2).
*Mar 1 00:09:08.282: -If a power-injector is installed, issue the command:"pow
er inline negotiation injector installed"
*Mar 1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using
static IP. Forcing AP to use DHCP.
*Mar 1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
Not in Bound state.
*Mar 1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP
. Renewing DHCP IP.
logs from wireless controller:
(Cisco Controller) >show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Gu
est
ap-manager 2 untagged 209.165.200.231 Dynamic Yes No
management 1 untagged 209.165.200.230 Static Yes No
service-port N/A N/A 192.168.1.157 Static No No
virtual N/A N/A 1.1.1.1 Static No No
(Cisco Controller) >
i conect with service-port ok and the management port works, i think.
AP442b.03dc.0925>ping 209.165.200.230
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
AP442b.03dc.0925>
Help, please!
i write in spanish:
Hola:
Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, GraciasHi!
I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.
I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.
Before the logs, I see this message from AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Hola:
He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.
Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.
Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Un saludo
Antonio R.
(Cisco Controller) >show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco Wireless Controller"
PID: AIR-CT5508-K9, VID: V02, SN: FCW1608L05X
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 17 mins 45 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Network Information
RF-Network Name............................. hosp
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 0
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Location
Site Name........................................ default-group
Site Description.................................
WLAN ID Interface Network Admission Control
1 management Disabled
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority GroupName
Press Enter to continue or to abort
AP Config
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Airewave Director Configuration
Press Enter to continue or to abort
802.11a Configuration
802.11a Network.................................. Disabled
11nSupport....................................... Enabled
802.11a Low Band........................... Enabled
802.11a Mid Band........................... Enabled
802.11a High Band.......................... Enabled
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC:
Voice AC - Admission control (ACM)............ Disabled
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Video AC:
Video AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Press Enter to continue or to abort
802.11a Advanced Configuration
Press Enter to continue or to abort
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
802.11a AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
--More or (q)uit current module or to abort
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
DCA Sensitivity Level.......................... STARTUP (5 dB)
DCA 802.11n Channel Width...................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
Allowed Channel List......................... 36,40,44,48,52,56,60,64
Unused Channel List.......................... 100,104,108,112,116,120,124,
128,132,136,140
DCA Outdoor AP option.......................... Disabled
Radio RF Grouping
802.11a Group Mode............................. AUTO
--More or (q)uit current module or to abort
802.11a Group Update Interval.................. 600 seconds
802.11a Group Leader........................... c4:64:13:8f:93:40
802.11a Group Member......................... c4:64:13:8f:93:40
802.11a Last Run............................... 75 seconds ago
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
--More or (q)uit current module or to abort
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Disabled
Priority 5............................... Disabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
--More or (q)uit current module or to abort
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Enabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice load-based CAC mode..................... Disabled
Voice tspec inactivity timeout................ Disabled
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ 50
Video reserved roaming bandwidth.............. 0
802.11b Advanced Configuration
Press Enter to continue or to abort
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
DCA Sensitivity Level: ...................... STARTUP (5 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11b Auto-RF Allowed Channel List........... 1,6,11
Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
Radio RF Grouping
802.11b Group Mode............................. AUTO
802.11b Group Update Interval.................. 600 seconds
802.11b Group Leader........................... c4:64:13:8f:93:40
802.11b Group Member......................... c4:64:13:8f:93:40
802.11b Last Run............................... 213 seconds ago
Mobility Configuration
Symmetric Mobility Tunneling (current) .......... Enabled
Symmetric Mobility Tunneling (after reboot) ..... Enabled
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... hosp
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x97e2
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name Multicast
IP Status
c4:64:13:8f:93:40 209.165.200.230 hosp 0.0.0.0
Up
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 0
Probe request rate-limiting interval............. 500 msec
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
dot11-padding.................................... Disabled
Authentication Response Timeout (seconds)........ 10
Rogue Entry Timeout (seconds).................... 1200
AP Heart Beat Timeout (seconds).................. 30
AP Discovery Timeout (seconds)................... 10
AP Local mode Fast Heartbeat (seconds)........... disable
AP Hreap mode Fast Heartbeat (seconds)........... disable
AP Primary Discovery Timeout (seconds)........... 120
AP Primed Join Timeout (seconds)................. 0
Packet Forwarding watchdog timer (seconds)....... 240 (enable)
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility.................................... Oui:00:14:7e : Vendor:pango S
tate:Disabled
Interface Configuration
Interface Name................................... management
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 209.165.200.230
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 209.165.200.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 192.168.1.1
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 209.165.200.230
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
Interface Name................................... service-port
MAC Address...................................... c4:64:13:8f:93:41
IP Address....................................... 192.168.1.157
IP Netmask....................................... 255.255.255.0
DHCP Option 82................................... Disabled
DHCP Protocol.................................... Disabled
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... virtual
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 1.1.1.1
DHCP Option 82................................... Disabled
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... HOSP3C
Network Name (SSID).............................. HOSP3C
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
WLAN ACL......................................... unconfigured
DHCP Server...................................... 209.165.200.230
DHCP Address Assignment Required................. Enabled
Quality of Service............................... Platinum (voice)
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11b and 802.11g only
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT(802.11r)............................. Disabled
FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout......................... 20
FT Over-The-Air mode............................. Enabled
FT Over-The-Ds mode.............................. Enabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Learn IP Address....................... Enabled
Infrastructure MFP protection................. Enabled
Client MFP.................................... Optional
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Band Select...................................... Enabled
Load Balancing................................... Enabled
Mobility Anchor List
WLAN ID IP Address Status
Press Enter to continue or to abort
Press Enter to continue or to abort
ACL Configuration
Press Enter to continue or to abort
CPU ACL Configuration
CPU Acl Name................................ NOT CONFIGURED
Wireless Traffic............................ Disabled
Wired Traffic............................... Disabled
RADIUS Configuration
Vendor Id Backward Compatibility................. Disabled
Call Station Id Case............................. lower
Call Station Id Type............................. IP Address
Aggressive Failover.............................. Enabled
Keywrap.......................................... Disabled
Fallback Test:
Test Mode.................................... Off
Probe User Name.............................. cisco-probe
Interval (in seconds)........................ 300
MAC Delimiter for Authentication Messages........ hyphen
MAC Delimiter for Accounting Messages............ hyphen
Authentication Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
Accounting Servers
Idx Type Server Address Port State Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
--More or (q)uit current module or to abort
TACACS Configuration
Authentication Servers
Idx Server Address Port State Tout
Authorization Servers
Idx Server Address Port State Tout
Accounting Servers
Idx Server Address Port State Tout
LDAP Configuration
Press Enter to continue or to abort
Local EAP Configuration
User credentials database search order:
Primary ..................................... Local DB
Timer:
Active timeout .............................. 300
Configured EAP profiles:
EAP Method configuration:
EAP-FAST:
Server key ................................
TTL for the PAC ........................... 10
Anonymous provision allowed ............... Yes
Authority ID .............................. 436973636f00000000000000000000
00
Authority Information ..................... Cisco A-ID
Press Enter to continue or to abort
HREAP Group Summary
HREAP Group Summary: Count: 0
Group Name # Aps
Press Enter to continue or to abort
HREAP Group Detail
Press Enter to continue or to abort
Route Info
Number of Routes................................. 0
Destination Network Netmask Gateway
Press Enter to continue or to abort
Qos Queue Length Info
Platinum queue length............................ 100
Gold queue length................................ 75
Silver queue length.............................. 50
Bronze queue length.............................. 25
Press Enter to continue or to abort
Mac Filter Info
Press Enter to continue or to abort
Authorization List
Authorize MIC APs against AAA ................... disabled
Authorize LSC APs against Auth-List ............. disabled
Allow APs with MIC - Manufactured Installed C.... disabled
Allow APs with SSC - Self-Signed Certificate..... disabled
Allow APs with LSC - Locally Significant Cert.... disabled
Load Balancing Info
Aggressive Load Balancing........................ Disabled
Aggressive Load Balancing Window................. 5 clients
Aggressive Load Balancing Denial Count........... 3
Statistics
Total Denied Count............................... 0 clients
Total Denial Sent................................ 0 messages
Exceeded Denial Max Limit Count.................. 0 times
None 5G Candidate Count.......................... 0 times
None 2.4G Candidate Count........................ 0 times
Press Enter to continue or to abort
Dhcp Scope Info
Scope: PUNTOSAP
Enabled.......................................... Yes
Lease Time....................................... 86400 (1 day )
Pool Start....................................... 209.165.200.201
Pool End......................................... 209.165.200.229
Network.......................................... 209.165.200.0
Netmask.......................................... 255.255.255.0
Default Routers.................................. 0.0.0.0 0.0.0.0 0.0.0.0
DNS Domain.......................................
DNS.............................................. 0.0.0.0 0.0.0.0 0.0.0.0
Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0
Press Enter to continue or to abort
Exclusion List ConfigurationUnable to retrieve exclusion-list entry
Press Enter to continue or to abort
CDP Configuration
Press Enter to continue or to abort
Country Channels Configuration
Configured Country............................. ES - Spain
KEY: * = Channel is legal in this country and may be configured manually.
A = Channel is the Auto-RF default in this country.
. = Channel is not legal in this country.
C = Channel has been configured for use by Auto-RF.
x = Channel is available to be configured for use by Auto-RF.
(-,-) = (indoor, outdoor) regulatory doamin allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11bg :
Channels : 1 1 1 1 1
: 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): A * * * * A * * * * A * * .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
802.11a : 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Channels : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
: 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E ,-E ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .
Press Enter to continue or to abort
WPS Configuration Summary
Auto-Immune
Auto-Immune.................................... Disabled
Client Exclusion Policy
Excessive 802.11-association failures.......... Enabled
Excessive 802.11-authentication failures....... Enabled
Excessive 802.1x-authentication................ Enabled
IP-theft....................................... Enabled
Excessive Web authentication failure........... Enabled
Signature Policy
Signature Processing........................... Enabled
Press Enter to continue or to abort
Custom Web Configuration
Radius Authentication Method..................... PAP
Cisco Logo....................................... Enabled
CustomLogo....................................... None
Custom Title..................................... None
Custom Message................................... None
Custom Redirect URL.............................. None
Web Authentication Type.......................... Internal Default
External Web Authentication URL.................. None
Configuration Per Profile:
Rogue AP Configuration
Rogue Location Discovery Protocol................ Disabled
Rogue on wire Auto-Contain....................... Disabled
Rogue using our SSID Auto-Contain................ Disabled
Valid client on rogue AP Auto-Contain............ Disabled
Rogue AP timeout................................. 1200
MAC Address Classification # APs # Clients Last Heard
Adhoc Rogue Configuration
Detect and report Ad-Hoc Networks................ Enabled
Auto-Contain Ad-Hoc Networks..................... Disabled
Client MAC Address Adhoc BSSID State # APs Last Heard
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
--More-- or (q)uit
MAC Address State # APs Last Heard
Ignore List Configuration
MAC Address
Rogue Rule Configuration
Priority Rule Name State Type Match Hit Count
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 41 mins 2 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +39 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
(Cisco Controller) >
The AP log
AP442b.03dc.0925>
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER
'(index 0).
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller
logging facility kern
^
% Invalid input detected at '^' marker.
logging facility kern
^
% Invalid input detected at '^' marker.
*Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23
0
*Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
*Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209
.165.200.230:5246
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established -
WAP321 & Aironet 2602e & 2504 Wireless Controller?
Hello,
I am new to Cisco networking. I am currently in an environment with no Wireless Controller and the wifi uses two Cisco WAP321's. The company wants to expand the wireless and has bought a Cisco 2504 Wireless Controller and a Cisco Aironet 2602e Controller-based WAP. My question is once we start using the controller can it control the formerly controller-less WAP321's or will that have to be replaced with another Cisco Aironet 2602e? Thank you.My question is once we start using the controller can it control the formerly controller-less WAP321's
WLC 2504 will not support AP321s. Talk to your authorized Cisco reseller and see if they will accept if you trade-in the AP321 for the AP 2602.
Make sure your AP 2602 have the correct regulatory domain. If you are un-sure DO NOT open the boxes.
For more information, go here:
http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps5861/product_data_sheet0900aecd80537b6a_ps10981_Products_Data_Sheet.html
Another thing, for AP 2600, your 2504 should have the minimum firmware of 7.2.110.X. IF you don't have it, then talk to the authorized Cisco reseller who sold you the controller and kindly ask them (nicely) if they could download the correct firmware for you. -
Managing remote C800 with the wireless controller
We have a number of regional offices throughout the country with a C800 as the Internet facing router and it is also our wireless.
We have a Cisco wireless controller in the Data Center an we need to manage\monitor all the C800, but the problem is that those remote sites
are not VPN'd nor part of our WAN network.
Which setup do you
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
recommend:
1) 1) WLC to monitor the C800 using its public IP address
1) 2) Create a VPN tunnel from each of the remote sites to our data center and only allow wireless to go through for mgmt purposes
anany other options?
TFirst question is which 800 do you have ? there's like 20 different versions out there.
If you talk about WLC, I would suppose you have something like the 880 ?
I'm afraid the WLC will need the internal AP ip address. So you would need to do so reverse nat to direct public ip address tarffic on capwap ports to the internal AP.
This or the VPN tunnel.
Nicolas
===
Don't forget to rate answers that you find useful -
Wireless controller 5500 and aironet 1142
We have a wireless controller 5500 at a hub site. The remote sites are running the aironet 1142 wap in controller mode. We configure dhcp option 43 at the remote isr's and the 1142 remote site waps's join the controller's as they should. The 1142's are getting the subnets from the hub site. Because of this, they are not subject to the web content filtering at the remote site, but rather the filtering at the hub site. We would rather they be subjet to the content filtering at the remote site. Is there a way to have the remote 1142 wap's connecting through, and drawing the subnet from the remote isr, so that they will be subject to the local content filtering.
Convert the WAPs to H-REAP (aka FlexConnect).
-
I am trying to get an AP to associate with a wireless Controller but keep getting this error message (%CAPWAP-3-ERRORLOG:Could not resovle CISCO-CAPWAP-CONTRPLLER)
I can ping through to the WLC and the AP.Thanks a lot Loe for the Feedback. The issue was not my configuration but rather the type of Wireless LAN controller I have, the WLC does not support my AP's. I have a Cisco 520 series WLC and got to know they only work with the 500 series AP's. my AP's are 1130 series meaning i have to get another controller or change the APs.
thanks once again.. -
If i connect cisco AP - CAP2702i to another switch, and use trunk port between Cisco3850 and the other switch , can the AP able to register with Cisco3850 with wireless LAN controller ? or the AP has to directly connect to Cisco3850 in order to register?
The AP and 3850 wireless management are in same Vlan( vlan202). The AP is new unit and did not join MC before.
What i did on 3850 :
input command - wireless management interface vlan 202
- ap cdp
- wireless mobility controller
Is there any config i miss out on 3850 and any config need to be set on AP ?
From Ap console output show me "could not discover WLC using dhcp ip". Is it due to AP dont have IP address? If AP register with WLC through layer 2 , i believe there is no related with IP.Correct me if i'm wrong.
Due to the 3850 is not a POE, the AP unable directly connect to 3850 . I guess have to use power adapter to power on the AP. -
Cisco 5508 Wireless Controller with Splash Page Disclaimer
How do one configure a splash disclaimer page on a Cisco Wireless Controller 5508 with no authentication?
JimmyThere are many options to you in this scenario, but if you're looking to simply provide a splash page via the WLC without interacting with any other web servers, you can configure Local Web Authentication (LWA) as seen in this configuration example.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/69340-web-auth-config.html?referring_site=RE&pos=1&page=http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/71881-ext-web-auth-wlc.html
If you are not wanting the authentication, you can choose the "passthrough" method which will not require any credentials, only accepting an AUP or whatever you want. -
Airnet 1130AG with no wireless controller?
Hi All,
We have recently moved into an office that has these wireless routers scattered around all running back to the comms room.
Is there any way of connecting these to our switch without a wireless controller? all we want to do is set them up with a wireless key and allow company access is this something that can be done easily?
Hope to hear from you all soon!Hello Shaun,
As per your query i can suggest you the following solution-
Yes. You can configure each AP as autonomous.
Configure the bridge group in the wireless interface with the bridge group dot11radio interface command.
This is an example.
AP# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
AP(config)# interface Dot11Radio0.1
Ap(config-subif)# encapsulation dot1q 1 native
Ap(config-subif)# bridge group 1
ap(config-subif)# exit
2.Configure the bridge group with the same bridge group number ("1" in this example) in the Fast Ethernet interface so that VLAN 1 traffic is passed across the wireless interface to this wired side and vice versa.
Ap(config)# interface fastEthernet0.1
Ap(config-subif)# encapsulation dot1q 1 native
Ap(config-subif)# bridge group 1
Ap(config-subif)# exit
For more information please refer to the link-
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml
Hope this will help you. -
How do I configure the 2504 Wireless controller with AP?
I recently purchase the 2504 wireless controller and the 1602i AP. I was able to do the basic setup of the controller and can now access the web interface, but the AP is not being detected and I am unable to add it.
First of all: 1602 AP need minimum software version on WLC: 7.4.100.0
paste this info:
sh sysinfo from WLC
sh version from AP.
Did you create a DHCP pool for APs to get IP ?
Try to to be keep AP and WLC on same subnet.
regards -
Wireless Controller 2504 with CAP1702i
I have installed and configure Cisco 2504 wireless controller. Also attached a AP(AIR-CAP1702i) in PoE port. But it's not showing in controller and also not showing SSID.
Please suggest.Searching WLANs
You can search for specific WLANs in the list of up to 512 WLANs on the WLANs page. This feature is especially useful if your WLANs span multiple pages, preventing you from viewing them all at once.
To search for WLANs using the controller GUI, follow these steps"
Step 1 On the WLANs page, click Change Filter. The Search WLANs dialog box appears (see Figure 7-4).
Figure 7-4 Search WLANs Dialog Box
Step 2 Perform one of the following:
•To search for WLANs based on profile name, select the Profile Name check box and enter the desired profile name in the edit box.
•To search for WLANs based on SSID, select the SSID check box and enter the desired SSID in the edit box.
•To search for WLANs based on their status, select the Status check box and choose Enabled or Disabled from the drop-down list.
Step 3 Click Find. Only the WLANs that match your search criteria appear on the WLANs page, and the Current Filter field at the top of the page specifies the search criteria used to generate the list (for example, None, Profile Name:user1, SSID:test1, Status:disabled).
Note To clear any configured search criteria and display the entire list of WLANs, click Clear Filter.
Maybe you are looking for
-
Since updating to itunes 11, Home Sharing is not working
Since updating to itunes 11, Home Sharing is not working. I am running Windows 7, 64-bit. All mobile devices are up to date with ios, including 2 apple tvs (2 & 3), iphone 4s and 3gs, ipad1 & ipad2. I've rebooted twice, turned home sharing off, then
-
IPod has erased its data, no longer appears in iTunes/deskto
I have switched using my iPod from the Windows system I began with to an iBook G4, but did not reset my factory settings because much of the music on the pod does not exist on my old computer. I recently was adding files to my iPod on the Mac in iTun
-
Finally Core2 Duos! ive been waiting since august to buy a new MBP. But i noticed that the 15" C2D MPBs dont have the 7200rpm HD option that the Core duos have, any reason why? is there anyway i can request one when i purchase? I would much rather ha
-
Problem in viewing equations with acrobat 8.1.2
When there is an equation in the pdf I see a box in front of it. Other paople (who use adobe reader) don't experience the same problem for the same file. Does anybody have an idea about how i can fix that? It's really irritating. Snapshot of what i s
-
Hi, I want to set the color of JTree's linestyle which areranch lines. what should i set to get the desired result. i set the linestyle by tree.putClientProperty("JTree.lineStyle", "Angled"); How can i set the linecolor? Thnaks, Sato