Aironets 1602 - clients with ~1700 ms responses ( random devices )

Hello
I am straggling with quite complex case, here is short description ( ask for more whats needed ).
- i had 9 AP of Aironet 1130AG in one location (two building) - running correctly for at least 4 years (except some individual incidents). Those AP was placed with Channels set based on surveys.
- ~4 months ago i replaced them by Aironet 1602 - applying same configuration and same channels.
- there were no problems identified until late December when i received frist claim. Clients connected to one of those AP has very poor network performance.
Here is what i have:
- ping to clients connected to this AP takes ~1700 ms or more ( some packed failed )
- no more that ~25 clients connected at that time ( based on experience in my topology i am running good with more than 40 clients and ~5ms respones on regular daily traffic basis )
 during reboot of such AP, clients roam to other AP wich in turn have sometimes 60 clients - and there all are running fine
- ping from Lan to AP interface is  1ms (constant) and i don't have any problem with clients in same vlan/switch connected by lan
- on LAN Switch port to which AP is connected to - there is no heavy or abnormal traffic coming from those clients ( sometimes even less that usual where usual is ~6 Mb, peaks ~10Mb
- based on inSSIDer its channel had no noise coming from other APs or foreign networks, anyway setting it with "Least Congested Fraquency" doesn't change the situation.
- there were no changes applied in lan/wifi infr. that i can start to check the issue.
- lately i applied 15.3(3)JAB firmware but seems is not resolving the problem
- in logs nothing to start with ( at least for me )
And maybe the most important:
- it start to occur with other APs as well and now from time to time it happens almost on all of those 9 devices ( different time frames and areas )
- when probelm occur i am able to "resolve" it only by changing channel to "other" one. it resolves for some time (1 or 2 days) until appear again and i can still resolve it by channing to other channel ( for example the same channel on which day ago was causing the slowness )
- i have 5 of such 1602 APs in other country ( same model and firmware ) and have no issue for last ~1,5 year ( those 5 differs by no VLANs and second SSID configured)
I am sorry for long post - trying to share the most i can.
I am not expecting resolution just help how to, where to start looking for the root problem ?
Thank you in advance
Regards

- 802.11n was one of the reasons why i moved to 1602
- i wrote "lately i applied 15.3(3)JAB firmware but seems is not resolving the problem" - but after checks could be "false alarm" as not related issue, I will keep it as is for next days awaiting feedback.
If not resolved i will follow your advice by "disabling the 802.11n"
Regarding "wireless NICs firmware" - what exactly do you mean?  is it separate upgrade not included in 15.3(3)JAB firmware upgrade?
Thank You

Similar Messages

  • How i install oracle client with ODBC using response file method

    Hi,
    I have managed to create a response file using OUI. Currently, I do not know what are the methods which i can install a group of computers using this response file. Any advise
    Thanks in advance.
    Best regards,
    Tony

    Presumably, any method that allows you to remotely run code on the group of computers would allow you to do a silent install of the Oracle client and ODBC driver. I know Microsoft and various third parties sell such tools, but I'm not enough of a Windows admin to know anything about the relative benefits of the products in this category.
    Justin

  • Connect WAP4410 to Aironet 1602 in Client mode doesn't work

    Hello,
    I wish to associate my WAP4410 Aironet 1602 to a wifi bridge.
    I will explain my progress.
    I configured an SSID on the Aironet (not in guest-mode) with WPA-PSK.
    My iphone and my Android able to connect to the Aironet, so we can assume that the link works.
    I configured my Android ICS Wifi + 3G with similar parameters.
    The WAP4410 can connect to the Android, but does not connect to the Aironet.
    The configuration on the WAP4410 is AP "Wireless Client / Repeater" mode with the SSID of the Aironet.
    And security in WPA-TKIP + Personnal.
    Do you have any idea?
    Thanks for your help.

    As Cody wrote, SP2 introduced changes in the way App-V handles permissions inside the package (which effectively hits the client's physical locations), also changes in how environments with folder redirection are supported change in SP2.
    HF4 for SP2 made some modifications, too.
    Are you using Folder Redirection for Appdata? Are you publishing the package in both scenarios (SP1, SP2) with the same scopes (user vs. global)?
    Falko
    Twitter
    @kirk_tn   |   Blog
    kirxblog   |   Web
    kirx.org   |   Fireside
    appvbook.com
    Hi
    We're not redirecting AppData and we only ever publish packages globally to the servers. I'm going to test the package using the HF4 client with the 'write to VFS' option selected and all files outside of the PVAD as per Cody's suggestion.
    I've done some more investigation and the two servers are both in the same OU, from what I can gather the only difference between the two is that one is SP1 and one is SP2.
    Thanks

  • Office 2013, click icon nothing happens, no errors, no eventlog, MANY clients with this issue

    We're an IT solutions provider for companies of all sizes as well, as residential users, and we've been plagued by a new Microsoft-caused issue that's seriously affecting our client's perception of us since it seems like 'you didn't fix it the first
    time' or 'you sold us the computer', so it's our responsibility to fix for free.
    We've experienced this with 17 people so far, ranging from residential clients with systems that have come from big box stores and from systems we've sold with Microsoft Office 2013 and basically the entire suite stops working.
    If you click an icon, you may see an hour glass for a few seconds and nothing happens (but usually nothing happens at all, as though you didn't click it).
    Diagnostic steps:
    No errors in eventlog, neither under system or application.
    No third party add-ins, sometimes it's a stock install on a new / fresh system.
    Starting Microsoft Office applications in safe mode, like winword /safe, has no effect.
    A quick repair or an online repair will not resolve the issue, it will say it's done but issue still exists.
    Microsoft Office 2013 cannot be uninstalled, we always receive the same error code: 0-4
    Some systems do not have third party antivirus, some are simply using Microsoft Security Essentials.
    This affects all Microsoft Office applications, including Outlook.
    Makes no difference if you use another user account or run-as admin.
    All Microsoft Office 2013 updates have been installed.
    The installation source is undetermined but recent issues stemmed from a physical media (.ISO) install from Microsoft's latest source.
    You cannot start the software by clicking on documents created with Office applications.
    The only way to remove Microsoft Office 2013 is with the removal tool "O15CTRRemove.diagcab".
    The problem returns after a random period of days and no client can relay the actual cause of the issue, it seems random in nature. After the issue is experienced, we go through the same steps including the necessity to utilize the removal tool.  
    This seems to be a new issue that's come out of the blue within the past few weeks, at least on our end. When 17 random people call out of the blue with the same problem, it suggests it's Windows Update related.
    I'm really hoping someone has some insight into this Microsoft glitch and knows of a secret hotfix or special trick to prevent it. I attempted to call Microsoft and it would be more enjoyable to punch a concrete wall since you're dealing with useless people
    in a foreign country who can't really comprehend the seriousness or technicality of the issue, and don't really care, and aren't skilled enough to provide
    insight.
    Does anyone know about this problem?

    Thank you for the reply.
    I understand the flash you are receiving while launching Excel or Word is very fast. However just wanted to check if it is possible to get a screenshot of it.
    Also, are you able to work fine on Excel or Word even after receiving the flash.
    It seems the Office installation might have not been done properly.
    There is a possibility, everytime you Uninstall any application, there are still some patches left behind which could cause an issue while Installing the same application again or even after Installation is successful, it sometimes gives
    issue while launching the application.
    If you want to give a try, you may try to Uninstall the product using Offscrub by clicking on the below link & then can have a fresh installation again.
    http://support.microsoft.com/kb/2739501
    Please let me know the status update once done
    Abhijeet, the box flash happens too fast for me to capture a screenshot of it but I believe it's similar to the smaller box activation process (enter your email).
    Word and Excel work fine whenever this is observed.
    I'm skeptical that this is a "not done properly" kind of scenario, especially when it applies to so many people and many have brand new computers. How can you take a Microsoft Office disc and install it improperly on a new PC? Or how can a person
    go through Microsoft's https://officesetup.getmicrosoftkey.com/ setup, use the software for months and suddenly it stops working? If this is a 'not done properly' scenario, then this is a failing of Microsoft's
    installation source. I can't reiterate this enough, the software works fine for people since installation date and then randomly stops working at a much later date (but many of them failed last month and this is a newer issue).
    I'm starting to get frustrated again as I'd already stated we've used your linked removal tool in my first post and the problem has returned for another user by which I'd used it and reinstalled the product. The client who's PC we have now, one we'd sold
    them, needs to be returned to them and while Microsoft Office is currently working, I was told that if this happens again, they're "going to throw the f#(*@ computer in the river". No joke.
    If we're at the point where we've moved past evaluating logs, registry keys, or file versions or anything along the lines of a developer determining how this Microsoft bug occurs, then I'll return the system back to the client and hope for the best.
    Three strikes and I'm out with this one but perhaps the delayed startup is the final solution... I just wish I knew for sure as we've had a bad year taking a beating for Microsoft's products and their support is the worst in the industry.
    It's further frustrating that since I'd touched base with Microsoft via phone calls, the only person who's been able to provide any insight into the issue is me.

  • AMT 3.2.10 Clients with SCCM 2012 on Windows 2012

    Hey
    I have a couple of HP dc7800 computers with Intel's AMT/vPro that I'd like to provision with SCCM 2012. The installed firmware version is 3.2.10 which is a supported version according to the documentation [1]. Provisioning of newer clients (5.2.x upwards)
    is successful, so I can rule out all the usual suspects like the provisioning certificate from GoDaddy, our internal CA, DHCP options, etc. Provisioning with SCCM 2007 of both 3.2.x and 5.x AMT devices is also still successful. 
    The amtopmgr.log repeatedly shows the following entries:
    Provision target is indicated with SMS resource id. (MachineId = 16777325 WS45.mydomain.ch)
    Found valid basic machine property for machine id = 16777325.
    Warning: Currently we don't support mutual auth. Change to TLS server auth mode.
    The provision mode for device WS45.mydomain.ch is 1.
    The IP addresses of the host WS45.mydomain.ch are x.x.x.x.
    Root hash of provisioning certificate is 2796BAE63F1801E277261BA0D77770028F20EEE4.
    Attempting to establish connection with target device using SOAP.
    Create provisionHelper with (Hash: 74B7792EDBD64EBB01E2E3A0B27FAFA04C2D3BCB)
    Set credential on provisionHelper...
    Try to use provisioning account to connect target machine WS45.mydomain.ch...
    Error 0x80090304 returned by InitializeSecurityContext during follow up TLS handshaking with server.
    **** Error 0x37f2b370 returned by ApplyControlToken
    Fail to connect and get core version of machine WS45.mydomain.ch using provisioning account #0.
    Try to use default factory account to connect target machine WS45.mydomain.ch...
    Error 0x80090304 returned by InitializeSecurityContext during follow up TLS handshaking with server.
    **** Error 0x37f2b370 returned by ApplyControlToken
    Fail to connect and get core version of machine WS45.mydomain.ch using default factory account.
    Try to use provisioned account (random generated password) to connect target machine WS45.mydomain.ch...
    Error 0x80090304 returned by InitializeSecurityContext during follow up TLS handshaking with server.
    **** Error 0x37f2b370 returned by ApplyControlToken
    Fail to connect and get core version of machine WS45.mydomain.ch using provisioned account (random generated password).
    Error: Device internal error. This may be caused by: 1. blabla...
    Error: Can NOT establish connection with target device. (MachineId = 16777325)
    After some investigation with Wireshark, I've found out that SCCM tries connect with TLSv1 to the AMT device. The response from the device is immediately an SSL alert (internal error). Using OpenSSL, I could connect to the device if I explicitly told it
    to use SSLv3. This leads me to believe that the 3.2.x firmware cannot handle TLSv1 correctly and SCCM never tries to connect with SSLv3 after a failure.
    So the question is: How can I get SCCM 2012 to provision these devices?
    Regards,
    Ingo
    [1]
    http://technet.microsoft.com/en-us/library/c1e93ef9-761f-4f60-8372-df9bf5009be0#BKMK_SupConfigOOB

    Since no one has answer this post, I recommend opening  a support case with CSS as they can work with you to solve this problem.
    Garth Jones | My blogs: Enhansoft and
    Old Blog site | Twitter:
    @GarthMJ

  • Exchange 2010 all mail clients with internal cached and internal non-cached mode users having connection status issues, login prompt -- external is fine either way

    Hello,
    I'm seeing an issue that started this past Monday with no recent change to our environment. 
    External Outlook Anywhere users and Mobile users, OWA users are unaffected.
    Internal Users are affected when using Outlook of any version, 2010 or 2013.
    -Internal Users normally log into their workstation with their ad credentials, domain joined machines. Outlook opens without credentials prompting ideally.
    1 . Using Cached Mode:
    a. Login Prompts, slowness - Since Monday, users are getting prompted to login. The prompt goes away after logging in at startup. It is also causing high CPU
    on the workstations.
    b. Free/Busy, Out of Office doesn't work. I can, however complete auto-setup for a new user, so autodiscover is not completely down for internal users.
    c. Checking Connection Status shows connecting status on highlighted entry below without ever establishing connection (just goes away).
    The outlook icon in the system tray says "Outlook is requesting data from the server":
    2. Using Non-cached mode 
    a. No Login Prompt at startup, business as usual
    b. Free/Busy, Out of Office works fine. Autodiscover is fine.
    c. Checking Connection Status shows normal except, it has "casarray URL, then status is referral" it seams to flicker this constantly then go away intermittently.
    d. Main issue in non-cached mode is, sometimes a user will log into windows, open outlook and it will not open and says "server is unavailable. Retry, work offline, or cancel" I can try re-opening, same message.
    Only after logging out of windows, logging back in, I can get back into outlook. This is not every time, or consistent with specific users, but random. 
    3. Lync Pop up  for credentials often, though entering the password.
    URLs are correct. Autodiscover, EWS, etc. 
    Already tried bypassing our loadmaster load balancer with host files on clients. same issue regardless of casarray node. 
    Not sure what is going on.
    Josh

    You have a hybrid configuration with Office 365, right?  You didn't provide this valuable piece of information.
    In Exchange Online PowerShell run this command:
    Get-OrganizationConfig | FL PublicFoldersEnabled
    If the value is "Remote" then users with Exchange Online mailboxes are looking to on-premises public folders.  Be sure that you have legacy pubic folder interoperability properly configured.
    http://technet.microsoft.com/en-us/library/dn249373(v=exchg.150).aspx
    Ed Crowley MVP "There are seldom good technological solutions to behavioral problems."

  • Web Service Client - SOAP/jms: Specific response queue (not default queue)?

    Hi @ll
    I try to define a specific jms response queue for a web service client that communicates SOAP/jms, running on a WLS 9.2. The web service itself runs also on a WLS 9.2 where also the request and response queues are located. By default the client receives the responses from a temporary response queue. Is there a way to define a specific response queue e.g. setting the JMSReplyTo property in the request on the client side?
    /cheers&greetz
    Dani

    WLS do not have a light SOAP client with callbacks yet. It is
    not a planed feature for 7.0, but we will considering this for
    post 7.0.
    regards,
    -manoj
    "markhu" <[email protected]> wrote in message
    news:[email protected]..
    Hi, guys:
    I have a system : client written in Java/Swing, HTTPS authentication,
    and then subscribes to a WLS 61. SP2 based JMS Topic and also has the
    ability to send message to a Queue, since I can not bring down the size of
    the client side WLS JMS dependency lib, I am thinking about using SOAP /
    web service as the communication tier between my client and server, so the
    question is: since the client need get the price updates in a real time
    mode, I need build a server side based PUSH for all the new price updates
    which come into the JMS Topic, and broadcast as SOAP messages to client,is
    this mean that I have to build the Call - Back for the Java Swing Client,so
    it can automatically get the new price updates as it's getting from JMS
    Topic now ? Any Idea on how to build server side PUSH based SOAP message
    center as web service ?? Thanks a lot.
    regards,
    mark
    FYI:
    I need the same PUSH service for my .NET based client as well.

  • Problem in accessing the url on client with win7 64 bit

    Hello experts,
    we recently install fusion 11.1.2.1.0 and database 11g.
    scenario:
    database server:(192.168.1.100)
    plateform: window server 2008, 64 bit
    product: oracle database 11g.
    application server:(192.168.1.101)
    plateform: window server 2008 64 bit
    product: oracle fusion 11g(forms and report)
    i sucessfully install and configure the forms configuration. my application is running on same application server.
    url to access the application:
    http://aserver:9001/forms/frmservlet?config=erp
    url is accessing on the application server as well as client having 32 bit xp operating
    system after insatlling the java.
    but if same url is accessing on database server and clients with window7 64 bit, not accessing after installing the java as well.
    please help
    thanks
    yash

    Hi Amit
    We also have this issue with weblogic webservices. Did you get any resolution for this issue.
    When the service is executed for lesser number of hits, all the responses are processed properly. But as load (Number of hits for the same service) increases, few responses are failed to be parsed in the web service client. We could confirm that the producer responds with proper content type (text/xml)
    Any help or pointers will be greatly appreciated.
    Thanks,
    Finny

  • VVX handset initiated call will not connect to Lync client with simultaneous ring enabled

    Has anyone encountered a similar issue? And any advice on how to fix it please? (note - a case has been logged with Polycom, but weeks are passing by and they have not provided any useful response so far; hence reaching out in
    the community for help) .... thanks in anticipation.
    Here's the scenario:
    A Lync 2010 user in the office (I'll call her Lisa) has setup her Sim Ring to an external number (her mobile number).
    Another Lync 2010 user in the office (Mike) calls Lisa's extension from his VVX410.
    Lisa answers the incoming call using her Lync client with a USB headset.
    The call appears to connect according to Mike and his VVX screen starts the call timer.
    Lisa's Lync client just says "Connecting Call ..."  but never actually connects.
    The line is silent for both Mike and Lisa.  There is no audio in either direction.
    Further testing reveals the following:
    The same problem occurs if Lisa uses a VVX handset to answer and also happens if she uses a CX600 handset to answer.  Hence the problem seems to relate specifically to the fact that Lisa has setup Sim Ring to an external number; rather than relating
    to the answering device type.
    If Lisa changes her Sim Ring so that it calls another internal extension, then the problem does not exist, i.e. calls connect fine.  Hence it seems to be specific to sim ring to an external number.
    The environment is Lync Server 2010 CU6, Lync client 2010 on Win 7 (although the same problem exists when tested with a Lync 2013 on Win 8.1 client); and with AudioCodes Mediant 2000 and 1000 gateways.  

    Please specify another external number for Simultaneously Ring.
    You phone may not have permission to dial an external phone number.
    Please check if you can call the external phone number directly.
    Lisa Zheng
    TechNet Community Support

  • How Client Browser Understand Server response

    Hi Experts,
    Iam new to java advance Technology. I hava a simple doubt, that "How Client Browser Understand Server response".
    suppose if u open multiple Browsers and u typing same URL in all browser window(www.rediffmail.com). The server will generate response for requested resources. I dont no how the response will received by client browser without any conflit.
    I need to know, whether the browser attach any ID to requested URL (or) any other machanism which helps the identification.
    plz reply with example
    Thank u

    Hi praks_it,
    "How Client Browser Understand Server response".
    I dont no how the response will received by client browser without any conflit.
    I need to know, whether the browser attach any ID to requested URL (or) any other machanism which helps the identification.
    The answers to all the above of ur questions is the HTTP (Hyper Text Transfer Protocol).
    It is a mechanism developed and documented by the W3C (World Wide Web Consortium) which specifies all needs for internet and browsers.
    Check out the following links and u'll gain more on the subject :
    1) http://www.google.co.in/search?hl=en&lr=&oi=defmore&q=define:HTTP
    2) http://www.w3.org/Protocols/rfc2616/rfc2616.html (recommended).
    Hope this helps.
    Cheers !!
    Sherbir

  • Deployment for 250 Clients with a poor communicationlink

    Hello guys :
    We're currently working with Forte 3.0.J.1.
    We have two questions :
    1.- We have a big application and when we deploy it the client
    partition is quite large.
    The size of the standard partition image repositories (*.btd,
    *.btx) is 7436 Kb.
    We then need to distribute the client files over a LAN (5% of the
    users) and over a
    WAN (96% of the users). Most of the users have a poor communication
    link ( 9600 bps !!!! ).
    We have two schemes for the distribution :
    a).- Configuration of the client machine ( forte control panel with
    flag :
    cfg:em:2:2:2. In this case, the client partition must be
    manually copied.
    This takes 50 minutes to copy via ftp. This flag requires
    the file being executed
    using ftexec -fi parameter.
    b).- Normal Forte mechanism, the client partition is being
    copied automatically once
    forte detects a difference with the current file. This
    takes 56 minutes via
    the Forte environment.
    Is there somebody having the same scenario ( low speed
    communications links ), if so
    can you share your experience with us?. Apart from that, we are
    having quite good
    response time inside the application.
    2.- What is the minimal configuration in memory (RAM) for a Central
    Server Node ( only Forte
    environment ). The machine is an Alpha 4100 with 1GB of RAM running
    Alpha Unix 4.0.D, the database is
    Sybase Adaptive Server 11.9.3 with 250 to 300 concurrent fort&eacute;
    users.
    Regards
    JAEB.
    Do You Yahoo!?
    Free instant messaging and more at http://messenger.yahoo.com
    To unsubscribe, email '[email protected]' with
    'unsubscribe forte-users' as the body of the message.
    Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>

    Hi,
    We've similar situation here but a little bit better. What we did was:
    1. We gzipped all the client btrees under appdist after deployment but
    before download.
    2. We wrote our own "Launcher" which would do one extra step - unzip
    the client btree before launching the client with normal launchservice.
    One drawback of this approach is that you will need
    1. hard-coding on unzipping the btree ( like hard-code for behaviour
    under Windows, Mac or UNIX )
    2. carefully designed application name. Note that Forte save the files
    in only 8 characters. Any name longer than that will be truncated with
    sequence number for the 8th character.
    One more thing that we've observed over WAN. When the traffic is really
    high and when we have a deployment, the nodemgr will crash claiming that it
    is out of memory. However, when we check the trace, the memory allocated by
    -fm is far more than enough. Thus, I suspected that when the download is
    slow, the nodemgr is flood with threads trying to download the applet to the
    client. And it is the thread manager that got boomed when there is really a
    lot of users. So beware.
    Regards,
    Peter Sham.
    -----Original Message-----
    From: Jorge Espinoza [SMTP:[email protected]]
    Sent: Wednesday, May 12, 1999 1:18 PM
    To: [email protected]
    Subject: Deployment for 250 Clients with a poor communication
    link
    Hello guys :
    We're currently working with Forte 3.0.J.1.
    We have two questions :
    1.- We have a big application and when we deploy it the client
    partition is quite large.
    The size of the standard partition image repositories (*.btd,
    *.btx) is 7436 Kb.
    We then need to distribute the client files over a LAN (5% of
    the
    users) and over a
    WAN (96% of the users). Most of the users have a poor
    communication
    link ( 9600 bps !!!! ).
    We have two schemes for the distribution :
    a).- Configuration of the client machine ( forte control
    panel with
    flag :
    cfg:em:2:2:2. In this case, the client partition must
    be
    manually copied.
    This takes 50 minutes to copy via ftp. This flag
    requires
    the file being executed
    using ftexec -fi parameter.
    b).- Normal Forte mechanism, the client partition is being
    copied automatically once
    forte detects a difference with the current file. This
    takes 56 minutes via
    the Forte environment.
    Is there somebody having the same scenario ( low speed
    communications links ), if so
    can you share your experience with us?. Apart from that, we are
    having quite good
    response time inside the application.
    2.- What is the minimal configuration in memory (RAM) for a Central
    Server Node ( only Forte
    environment ). The machine is an Alpha 4100 with 1GB of RAM
    running
    Alpha Unix 4.0.D, the database is
    Sybase Adaptive Server 11.9.3 with 250 to 300 concurrent fort&eacute;
    users.
    Regards
    JAEB.
    Do You Yahoo!?
    Free instant messaging and more at http://messenger.yahoo.com
    To unsubscribe, email '[email protected]' with
    'unsubscribe forte-users' as the body of the message.
    Searchable thread archive
    <URL:http://pinehurst.sageit.com/listarchive/>
    To unsubscribe, email '[email protected]' with
    'unsubscribe forte-users' as the body of the message.
    Searchable thread archive <URL:http://pinehurst.sageit.com/listarchive/>

  • ASA , Cisco VPN client with RADIUS authentication

    Hi,
    I have configured ASA for Cisco VPN client with RADIUS authentication using Windows 2003 IAS.
    All seems to be working I get connected and authenticated. However even I use user name and password from Active Directory when connecting with Cisco VPN client I still have to provide these credentials once again when accessing domain resources.
    Should it work like this? Would it be possible to configure ASA/IAS/VPN client in such a way so I enter user name/password just once when connecting and getting access to domain resources straight away?
    Thank you.
    Kind regards,
    Alex

    Hi Alex,
    It is working as it should.
    You can enable the vpn client to start vpn before logon. That way you login to vpn and then logon to the domain. However, you are still entering credentials twice ( vpn and domain) but you have access to domain resources and profiles.
    thanks
    John

  • Copy client with open items FI, stocks MM and balance from one client to

    Hi Gurus,
    I have a question , I want to copy client with next information:
    1.- All Cuztomazing
    2.- All master data
    3.- Only open items FI-AR , FI-AP,
    4.- Stocks MM available for production.
    5.- Documents sales valids
    6.- Complete Balance (fixed , available and current asset, etc.)
    From one client to other client.
    ¿How can I do it?
    I know that cuztomazing and master data it's possible, I need to find from 3 to 6 point if it's possible for copy tables or some trx complete this information.
    This work it's because my company code changue NIF and  information TAX , and I need to have a cut over for carry forward only the describe information.
    Thank's a lot
    Regards
    Julio

    Hi Julio,
    How did you solve this? I need to perform exactly these steps.
    I am very interested in 3, 4 and 6.
    Thanks in advance.

  • Error while creating the HTTP client with destination GB_DPSRetrieve

    Hi All,
    It is an interface R/3 -->XI --> HTTP ( proxy to HTTP ).
    Please find the error log below and throw some light why the HTTP adapter is getting error -
      <?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
    - <!--  Call Adapter
      -->
    - <SOAP:Envelope xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" xmlns:SAP="http://sap.com/xi/XI/Message/30">
    - <SOAP:Header>
    - <SAP:Main xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" xmlns:wsu="http://www.docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-utility-1.0.xsd" versionMajor="003" versionMinor="000" SOAP:mustUnderstand="1" wsu:Id="wsuid-main-92ABE13F5C59AB7FE10000000A1551F7">
      <SAP:MessageClass>SystemError</SAP:MessageClass>
      <SAP:ProcessingMode>synchronous</SAP:ProcessingMode>
      <SAP:MessageId>DC98499F-7E42-74F1-A41F-0017A4107EE6</SAP:MessageId>
      <SAP:RefToMessageId>DC98499C-A1EA-BEF1-B4DD-00110A63BF06</SAP:RefToMessageId>
      <SAP:TimeSent>2007-11-21T15:51:30Z</SAP:TimeSent>
    - <SAP:Sender>
      <SAP:Party agency="http://sap.com/xi/XI" scheme="XIParty">GovernmentGateway</SAP:Party>
      <SAP:Service>GGMailbox</SAP:Service>
      <SAP:Interface namespace="http://sap.com/xi/E-FILING_GB/2005">DPSretrieve</SAP:Interface>
      </SAP:Sender>
    - <SAP:Receiver>
      <SAP:Party agency="" scheme="" />
      <SAP:Service>SAP_DEV_ERP2005</SAP:Service>
      <SAP:Interface namespace="http://sap.com/xi/HR">HR_GB_EFI_DPSretrieve</SAP:Interface>
      </SAP:Receiver>
      <SAP:Interface namespace="http://sap.com/xi/E-FILING_GB/2005">DPSretrieve</SAP:Interface>
      </SAP:Main>
    - <SAP:ReliableMessaging xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1">
      <SAP:QualityOfService>BestEffort</SAP:QualityOfService>
      </SAP:ReliableMessaging>
    - <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1">
      <SAP:Category>XIAdapter</SAP:Category>
      <SAP:Code area="PLAINHTTP_ADAPTER">ATTRIBUTE_CLIENT_DEST</SAP:Code>
      <SAP:P1>GB_DPSRetrieve</SAP:P1>
      <SAP:P2 />
      <SAP:P3 />
      <SAP:P4 />
      <SAP:AdditionalText />
      <SAP:ApplicationFaultMessage namespace="" />
      <SAP:Stack>Error while creating the HTTP client with destination GB_DPSRetrieve</SAP:Stack>
      <SAP:Retry>N</SAP:Retry>
      </SAP:Error>
    - <SAP:HopList xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1">
    - <SAP:Hop timeStamp="2007-11-21T15:51:30Z" wasRead="false">
      <SAP:Engine type="BS">SAP_DEV_ERP2005</SAP:Engine>
      <SAP:Adapter namespace="http://sap.com/xi/XI/System">XI</SAP:Adapter>
      <SAP:MessageId>DC98499C-A1EA-BEF1-B4DD-00110A63BF06</SAP:MessageId>
      <SAP:Info>3.0</SAP:Info>
      </SAP:Hop>
    - <SAP:Hop timeStamp="2007-11-21T15:51:30Z" wasRead="false">
      <SAP:Engine type="IS">is.00.lbsth-tb1ci</SAP:Engine>
      <SAP:Adapter namespace="http://sap.com/xi/XI/System">XI</SAP:Adapter>
      <SAP:MessageId>DC98499C-A1EA-BEF1-B4DD-00110A63BF06</SAP:MessageId>
      <SAP:Info>3.0</SAP:Info>
      </SAP:Hop>
    - <SAP:Hop timeStamp="2007-11-21T15:51:30Z" wasRead="false">
      <SAP:Engine type="IS" />
      <SAP:Adapter namespace="http://sap.com/xi/XI/System">HTTP</SAP:Adapter>
      <SAP:MessageId>DC98499C-A1EA-BEF1-B4DD-00110A63BF06</SAP:MessageId>
      <SAP:Info />
      </SAP:Hop>
      </SAP:HopList>
    - <SAP:RunTime xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/">
      <SAP:Date>20071121</SAP:Date>
      <SAP:Time>155130</SAP:Time>
      <SAP:Host>lbsth-tb1ci</SAP:Host>
      <SAP:SystemId>XIS</SAP:SystemId>
      <SAP:SystemNr>00</SAP:SystemNr>
      <SAP:OS>Windows NT</SAP:OS>
      <SAP:DB>ORACLE</SAP:DB>
      <SAP:Language />
      <SAP:ProcStatus>023</SAP:ProcStatus>
      <SAP:AdapterStatus>000</SAP:AdapterStatus>
      <SAP:User>PISUPER</SAP:User>
      <SAP:TraceLevel>1</SAP:TraceLevel>
      <SAP:LogSeqNbr>000</SAP:LogSeqNbr>
      <SAP:RetryLogSeqNbr>000</SAP:RetryLogSeqNbr>
      <SAP:PipelineIdInternal>SAP_CENTRAL</SAP:PipelineIdInternal>
      <SAP:PipelineIdExternal>CENTRAL</SAP:PipelineIdExternal>
      <SAP:PipelineElementId>60C3C53B4BB7B62DE10000000A1148F5</SAP:PipelineElementId>
      <SAP:PipelineService>PLSRV_CALL_ADAPTER</SAP:PipelineService>
      <SAP:QIdInternal />
      <SAP:CommitActor>X</SAP:CommitActor>
      <SAP:SplitNumber>0</SAP:SplitNumber>
      <SAP:NumberOfRetries>0</SAP:NumberOfRetries>
      <SAP:NumberOfManualRetries>0</SAP:NumberOfManualRetries>
      <SAP:TypeOfEngine client="200">CENTRAL</SAP:TypeOfEngine>
      <SAP:PlsrvExceptionCode />
      <SAP:EOReferenceRuntime type="TID" />
      <SAP:EOReferenceInbound type="TID" />
      <SAP:EOReferenceOutbound type="TID" />
      <SAP:MessageSizePayload>0</SAP:MessageSizePayload>
      <SAP:MessageSizeTotal>2918</SAP:MessageSizeTotal>
      <SAP:PayloadSizeRequest>0</SAP:PayloadSizeRequest>
      <SAP:PayloadSizeRequestMap>0</SAP:PayloadSizeRequestMap>
      <SAP:PayloadSizeResponse>0</SAP:PayloadSizeResponse>
      <SAP:PayloadSizeResponseMap>0</SAP:PayloadSizeResponseMap>
      <SAP:Reorganization>INI</SAP:Reorganization>
      <SAP:AdapterInbound>PLAINHTTP</SAP:AdapterInbound>
      <SAP:AdapterOutbound>IENGINE</SAP:AdapterOutbound>
      <SAP:InterfaceAction>INIT</SAP:InterfaceAction>
      <SAP:RandomNumber>15</SAP:RandomNumber>
      <SAP:AckStatus>000</SAP:AckStatus>
      <SAP:SkipReceiverDetermination />
      <SAP:Receiver_Agreement_GUID>24422A5646443F8E9D975D57A3EE8162</SAP:Receiver_Agreement_GUID>
      </SAP:RunTime>
    - <SAP:PerformanceHeader xmlns:SAP="http://sap.com/xi/XI/Message/30">
    - <SAP:RunTimeItem>
      <SAP:Name type="ADAPTER_IN">INTEGRATION_ENGINE_HTTP_ENTRY</SAP:Name>
      <SAP:Timestamp type="begin" host="lbsth-tb1ci">20071121155130.5</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="ADAPTER_IN">INTEGRATION_ENGINE_HTTP_ENTRY</SAP:Name>
      <SAP:Timestamp type="end" host="lbsth-tb1ci">20071121155130.515</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="CORE">INTEGRATION_ENGINE</SAP:Name>
      <SAP:Timestamp type="begin" host="lbsth-tb1ci">20071121155130.515</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="CORE">INTEGRATION_ENGINE</SAP:Name>
      <SAP:Timestamp type="end" host="lbsth-tb1ci">20071121155130.515</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="PLSRV">PLSRV_RECEIVER_DETERMINATION</SAP:Name>
      <SAP:Timestamp type="begin" host="lbsth-tb1ci">20071121155130.515</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="PLSRV">PLSRV_RECEIVER_DETERMINATION</SAP:Name>
      <SAP:Timestamp type="end" host="lbsth-tb1ci">20071121155130.515</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="PLSRV">PLSRV_INTERFACE_DETERMINATION</SAP:Name>
      <SAP:Timestamp type="begin" host="lbsth-tb1ci">20071121155130.515</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="PLSRV">PLSRV_INTERFACE_DETERMINATION</SAP:Name>
      <SAP:Timestamp type="end" host="lbsth-tb1ci">20071121155130.515</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="PLSRV">PLSRV_RECEIVER_MESSAGE_SPLIT</SAP:Name>
      <SAP:Timestamp type="begin" host="lbsth-tb1ci">20071121155130.515</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="PLSRV">PLSRV_RECEIVER_MESSAGE_SPLIT</SAP:Name>
      <SAP:Timestamp type="end" host="lbsth-tb1ci">20071121155130.515</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="PLSRV">PLSRV_MAPPING_REQUEST</SAP:Name>
      <SAP:Timestamp type="begin" host="lbsth-tb1ci">20071121155130.515</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="PLSRV">PLSRV_MAPPING_REQUEST</SAP:Name>
      <SAP:Timestamp type="end" host="lbsth-tb1ci">20071121155130.531</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="PLSRV">PLSRV_OUTBOUND_BINDING</SAP:Name>
      <SAP:Timestamp type="begin" host="lbsth-tb1ci">20071121155130.531</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="PLSRV">PLSRV_OUTBOUND_BINDING</SAP:Name>
      <SAP:Timestamp type="end" host="lbsth-tb1ci">20071121155130.531</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="PLSRV">PLSRV_CALL_ADAPTER</SAP:Name>
      <SAP:Timestamp type="begin" host="lbsth-tb1ci">20071121155130.531</SAP:Timestamp>
      </SAP:RunTimeItem>
    - <SAP:RunTimeItem>
      <SAP:Name type="CORE">INTEGRATION_ENGINE</SAP:Name>
      <SAP:Timestamp type="end" host="lbsth-tb1ci">20071121155130.656</SAP:Timestamp>
      </SAP:RunTimeItem>
      </SAP:PerformanceHeader>
    - <SAP:Diagnostic xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1">
      <SAP:TraceLevel>Information</SAP:TraceLevel>
      <SAP:Logging>Off</SAP:Logging>
      </SAP:Diagnostic>
    - <SAP:Trace xmlns:SAP="http://sap.com/xi/XI/Message/30">
      <Trace level="1" type="T">SystemError message generated. Guid: DC98499F7E4274F1A41F0017A4107EE6</Trace>
      <Trace level="1" type="T">Error during execution of message : DC98499CA1EABEF1B4DD00110A63BF06</Trace>
      <Trace level="1" type="T">ApplicationMessage was (=RefToMsgId): DC98499CA1EABEF1B4DD00110A63BF06</Trace>
      <Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_TO_PERSIST" />
    - <!--  ************************************
      -->
      </SAP:Trace>
      </SOAP:Header>
    - <SOAP:Body>
      <SAP:Manifest xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:xlink="http://www.w3.org/1999/xlink" xmlns:wsu="http://www.docs.oasis-open.org/wss/2004/01/oasis-200401-wss-wssecurity-utility-1.0.xsd" wsu:Id="wsuid-manifest-5CABE13F5C59AB7FE10000000A1551F7" />
      </SOAP:Body>
      </SOAP:Envelope>
    Regards,
    Kishore

    Hi,
    In the HTTP Receiver what is the Addressing Type used ? (URL Address or HTTP Destination).
    If its URL Addressing Type, check if right Authentication Type is used with valid values and for HTTP Addressing Type check this HTTP Client Create Error, it could be helpful.
    Also check if the Target system can be reached from the XI server to validate the configuration parameters.
    Regards,
    S.Santhosh Kumar

  • How to develope a XML-RPC client with PL/SQL

    Anyone know how to develop a XML-RPC client with PL/SQL?
    I've oracle 8i.
    Have you some example of code?
    Thanks
    Paolo

    So, you actually want to create the physical directory using JAVA?
    Then see:
    http://www.oracle-base.com/articles/8i/shell-commands-from-plsql.php

Maybe you are looking for