Airport Express 802.11n will not hard reset or firmware.

Greetings. I received notice that there was a firmware update for my Airport Express. Tried to install and the update process just hangs and eventually times out. Am trying to view settings on the Airport Express but the wait symbol just spins. Attempted to do both a hard reset and factory default reset and neither of those are working either. Did the failed firmware update process pooch the Express?

Hi there, I experienced the same problem. Here was my solution, it takes a lot of pressing on that reset button. I have a Time Capsule, too, so if you don't maybe this isn't as helpful as you'd prefer....but here goes. I pressed the reset button, briefly mind you, while it was plugged in. This caused the LED to start blinking rapidly yellow. Then I connected an ethernet cable to the EXPRESS and unplugged, then plugged back in. I could suddenly "see" the Airport Express again in the admin utility. Then I logged on to it, and chose to Restore Default Settings. Restarted again. Then and only then, I reapplied the firmware update 7.3.2, which appeared to work fine. Then after that, I was able to re-add it as "Extend My Wireless Network" into the Airport Extreme's wifi net. I hope that this helps. Remember, pressing the reset button is the key. The Hard Reset method did not work after the incomplete firmware update that was the precursor to all the problems that you and I were having. Good luck!

Similar Messages

Airport Express 802.11n does not support 5 ghz range

I have a Airport Extreme and a Airport Express both are 802.11n. I have the Airport Extreme setup to 802.11n (5ghz only). The Airport Express 802.11n will not work in the 5ghz range no matter what I do.
If I change the Extreme to 802.11n (2.4 ghz only), and set the Express to 802.11n 2.4ghz, it works fine.
Both systems have been upgraded to the 5.3.1 firmware.
Apple claims the Express works in the 5ghz range. The unit I have does not..so what is the deal?
Steve

I finally got this to work at 5ghz.
BUT,
The Airport Utility that supports the Express is less then great. There is no manual option to set the Express at 5ghz as a client. I assume that Apple will fix this soon.
I also had the problem described in several places in this Discussion group, that the Express becomes un-available after changing the config. I finally just restored it to the default, unplugged it and let it sit overnight. Then I reprogrammed it, saved it, verified it works, then let it sit all day with out unplugging it. I then unplugged it and moved it to the location I wanted it at so I could stream music, and it worked fine at 802.11n/5ghz.

Airport Express 802.11n Wi-Fi alternating green amber light

Apparent power surge causes AirPort Express 802.11n to not work correctly. Has alternating Green, Green, Amber light. How do I restore notmal functions?

As a last resort, try a Factory Default Reset to see if that might help.
Power off the Express for a minute
Hold in the reset button first, and keep holding it for another 10 seconds while you simultaneously plug the power back into the Express
Release the reset button after the hold period and allow a full minute for the Express to restart
At this point, you want to see a slow, blinking amber light, which is an indicatation that the Express has been reset and can now be reconfigured.
If after a few tries with the Factory Default Reset the Express still displays an alternating amber and green light, the Express has been damaged and will need to be replaced.

I'm trying to extend the range of an Airport Extreme 802.11g by adding an Airport Express 802.11n. I set the Express up to join the existing network, but it does not make any difference in the range of the network. What's wrong?

I'm trying to extend the range of an Airport Extreme 802.11g by adding an Airport Express 802.11n. I set the Express up to join the existing network, but it does not make any difference in the range of the network. What's wrong?

Let me see if I can help you with the basic WDS configuration steps:
Note: To help facilitate the setup, temporarily connect the AXn directly to the AEBS LAN port using an Ethernet cable. Once the setup is complete, you can move the AXn to the desired location. For all configuration steps you will be using the AirPort Utility. Before starting, be sure to jot down the AppleIDs for both base stations.
802.11g AirPort Extreme Base Station (AEBS) Configuration
AirPort Utility > Select the AEBS > Manual Setup > Wireless tab
Wireless Mode: Participate in a WDS network
Manual Setup > WDS tab
WDS Mode: WDS main
Allow wireless clients (checked)
WDS Remotes: <enter the AppleID for the AXn here>
Click on Update and allow the base station to restart.
802.11n AirPort Express Base Station (AXn) Configuration
AirPort Utility > Select the AXn > Manual Setup > Wireless tab
Wireless Mode: Participate in a WDS network (Note: You may have to hold down the Option (Mac) or Control (PC) key to see this option in the list.)
Manual Setup > WDS tab
WDS Mode: WDS remote
Allow wireless clients (checked)
WDS Main: <enter the AppleID for the AEBS here>
Click on Update and allow the base station to restart.

Airport Express 802.11n not seen in utility scan

I have an Airport Express 802.11n and the Airport utility scan isn't seeing it. I've reset it back to factory and still not being seen. Help please

After a factory default reset, the AirPort Express is broadcasting a wireless network with a name like Apple Network xxxxxx.
If you are tying to configure the Express using wireless, you need to make sure that your Mac is logged on to this network first, before you open AirPort Utility.
It's also possible to connect an Ethernet cable from your Mac to the AirPort Express and then open AirPort Utility. Once the Express has been configured an updated, you can remove the Ethernet cable.

Resetting Airport Express 802.11n Wi-fi

Hi. I'm having problems with my new AirPort Express 802.11n.
I am attempting a factory reset, but am reading conflicting instructions. Please confirm the correct (sequence) of steps: (a) hold down reset button (b) plug into power while holding down the button (c) wait until light flashes. This is where I get confused: in the manual, it says wait until it's flashing amber and on the Apple website: http://support.apple.com/kb/HT1450?viewlocale=en_US it says wait until it flashes green 4 times. Which is the correct way? And, do I have the DSL model connected to the Airport Express while I'm resetting, or just the Airport Express by itself?
And, any tips on getting the Airport Utility to recognize the AirPort Express so that it can be configured?
Any type of advice / help would be appreciated.

This is where I get confused: in the manual, it says wait until it's flashing amber and on the Apple website: http://support.apple.com/kb/HT1450?viewlocale=en_US it says wait until it flashes green 4 times. Which is the correct way?
The support link is correct. You should see four green flashes.
And, do I have the DSL model connected to the Airport Express while I'm resetting, or just the Airport Express by itself?
Although it is not required, I would disconnect the DSL modem when performing a reset.
And, any tips on getting the Airport Utility to recognize the AirPort Express so that it can be configured?
If you attempting to access it wirelessly with the AirPort Utility, be sure that you first connect to the AXn's wireless network. If that still doesn't work, try (temporarily) connecting you computer directly, using an Ethernet cable, to the Ethernet port on the AXn ... and then, try accessing it with the AirPort Utility.

I recently switched from LinkSys to Airport Express 802.11n. I love it, but I can't get the Wii to talk to it so I can stream NetFlix. I've found MANY discussions on this, but it's still not clear to me. Anybody have a step by step so I can fix it?

I recently switched from LinkSys to Airport Express 802.11n. I love it...but now I my Wii can't see it so I can stream NetFlix. I have found MANY discussions on line about this...but it's still not clear to me. Anybody have a step by step way to fix this? Thanks! Jim Matherly

Well, the Airport Express is also compatible with 802.11a, 802.11b, and 802.11g. If your Wii is unable to connect to the wireless network, I recommended changing the wireless security of your network.
Open Airport Utility, select your Airport Express and click Edit. Navigate to the Wireless tab and change your security from WPA2 Personal to WPA/WPA2 Personal. Then click Update on the bottom right.

Unable to Connect Using New AirPort Express 802.11n

My mom purchased an AirPort Express 802.11n wireless router (AX) and I, as the designated "technology guru", was tasked with setting it up. Unfortunately, I am having problems out of the box.
When I connect it to the wall, it is found by AirPort Utility, but when I try to set it up, it is unable to connect to the wireless network. ("An error occurred joining the selected wireless network." "An error occurred, close the configuration window and try again.") This is annoying because I have an older AX and it was true to the "it just works" Apple mantra. It is also annoying because the error message has a comma splice.
Feeling pretty proud of my "technology guru" title, I come here to see what I could be doing wrong. I try connecting the computer directly to the router via ethernet cable. With this, I am able to setup my wireless network. I am still not able to connect to it. Additionally, once the AX has been configured, the AirPort Utility can't find it.
I tried updating firmware to 7.5.2. I've tried downgrading to 7.3.2. I've tried hard resets, soft resets. Every tip I could find I have tried. Please help. My self-confidence is wearing out.
Is it time for a call to Apple or a visit to the Apple Store?

Are you trying to configure the Express to "join" the wireless network?
If yes, the message you are receiving is likely an indication that you do not have the correct security settings selected for the Express. Unless the security settings between the wireless router and Express match up exactly, the Express will display the error that "an error occurred, etc".
The easiest way to confirm if you have this problem is temporarily set the main wireless router to "no security" and try to connect the Express that way. If you can connect, then you know that it is a security issue.
Please tell us the exact setting for security that the wireless router there is using and we'll try to give you some more ideas.
The Express will connect. It's just a matter of finding the right settings.
Message was edited by: Bob Timmons

After setting up my brand new Airport Express 802.11n and accidentally using it to connect my iMac to the network...my iMac no longer connects through Ethernet? Any ideas...I have tried everything without success!!

I have been using Apple technology for about 10 years starting with 1st generation iPods and our house now includes a 5 year old iMac, all versions of iPods and touches, Apple TVs (both generations) and most recently an iPad 2. I have always told family and friends that Apple technology just works. Unfortunately that stopped today. I bought a new Airport Express 802.11n to use for AirTunes around my new pool. I set it up from my iMac and accidentally used it to connect my iMac to the network for a short time. Now I can no longer connect the iMac to the network using a hard wired Ethernet cable. I have tried resetting everything possible, from hubs to routers to the Mac itself and it just will not connect to the network through Ethernet any longer. I am now a very frustrated Apple user especially when the support site says I can't use the fast path support because my product was manufactured 5 years ago...I just bought it at BestBuy yesterday. All other computers and itechnology in the house are connecting via wifi and Ethernet without any issue except from my new iMac boat anchor. Anybody who can help me??? Thanks

John, thanks for the email so quickly.
I too hope I haven't tried "everything" either but I am reasonably technical. I had done what you suggested to do before but I did both again.
Ethernet is yellow in the left side bar. In the right pane it's status says Connected but then below it says "Ethernet has a self-assigned IP address and will not be able to connect to the Internet."
I have tried the assist me menu and Network Status has Ethernet Green, Network settings Yellow, ISP Green, and Internet and Server Red and Failed for both. I have turned things off and on, checked cables, deleted all locations and tried restting them up but to no avail. I even disconnected everything and connected the mac directly into the cable modem itself and the thing still will not connect.
Thoughts???

BDP-N460 Blue Ray - Wanting to implement Airport Express (802.11n) as Wi-Fi

Hi All,
My intention is to use my Airport Express (802.11n) as a Wi-Fi bridge for the BDP-N460 (Streaming Video). I am clearly missing a step. I have read many posts and followed what seemed like specific directions, to no avail. If anyone can help by shedding some light on this process, I would greatly appreciate it.
All the Best,
NgM

I may have to wait to do the tests in the same room as the Linksys. What would the tests include? Setting up the Express directly to the (cable) modem?
This was a suggestion to test signal strength. If you want to try to configure it now, here is how you would do so:
It is critically important that you know the exact type of security that the Linksys router is using. Otherwise, you will not be able to match up the settings and the Express will not connect to the Linksys wireless. It would be great if the Linksys was using no security, but I doubt that this is the case.
Hold in the reset button on the AirPort Express until you see the amber light begin to blink more quickly. Hold another second or two when you see this, then release the reset button.
Temporarily, connect an ethernet cable from your computer to the AirPort Express.
Open AirPort Utility and click Manual Setup
Click the Base Station tab (under the row of icons) to assign a name to your Express, a device password (write this down) and adjust Time Zone settings
Click the Wireless tab (under the row of icons)
Wireless Mode = Join a wireless network
Wireless Network Name = If the Express "sees" a strong enough signal from the Linksys, you will see the name of the Linksys wireless network. Click to select. If you do not see the name of the Linksys wireless network displayed as a choice, I'm afraid that the wireless signal is too weak and this will not work.
Place a check mark next to Allow ethernet clients. This activates the ethernet port
Wireless Security = Exact setting as the Linksys. This is always the most difficult part of trying to get an Express to join a wireless network. It won't pick the right setting by itself. You have to tell is exactly what to do.
Wireless Password = Password for the Linksys network if security is being used
Confirm Password
Click the Update button at the lower right of the window. Don't panic when the AirPort Express "disappears" from AirPort Utility, this is normal. As soon as you see the message that the settings have been stored to the Express, close AirPort Utility and disconnect the ethernet cable. The Express will restart and if your settings are correct, you will have a green light in 20-25 seconds.
If you don't get a green light, something is wrong with the configuration settings, probably the security setting. You'll have to start all over again with the reset of the Express and try again.
Now, test the connection by first plugging your computer in to the Express, (turn off wireless on the computer) and see if you can get an internet connection. If you can, it should be simply a matter of plug and play with the Sony, following the instructions in the manual. Almost all Audio/Video devices will connect to the internet automatically when they have an ethernet connection. No special configuration is normally required.
The success of your connection will depend on the quality of the wireless signal that is available to the AirPort Express.
Good luck, post back on your results.

Speed issue with TC and Airport Express 802.11n in WDS mode...

Here is my problem.
I replaced my older base station / Express duo with
a new Time Capsule (1TB) and a new Airport Express (802.11n).
I set up the network with the TC as base station running a WDS network (WDS main) and the Express is the WDS remote.
When I check the wireless clients from the TC, I find my iMac running at 130Mbits and the Extreme at 54Mbits.
No other wireless clients are connected to the network (I kept my slower network as a parallel one for my "older" Macs).
The only other connected device is my Dish network DVR that is connected via an Ethernet cable directly to the Express.
So my question is why does the Express not communicate at >54 speed rate with the TC?
And, why does my iMac connect with 130 and not with 300Mbits?
Any thoughts?

Instead of using WDS, you should take advantage of the "Allow this network to be extended" option that is available for the 802.11n AirPorts including the TC. WDS only operates in the 802.11g radio mode.
Here's the basic setup:
o If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
o Open AirPort Utility and select the base station that will connect to the Internet.
o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
o Click AirPort in the toolbar, and then click Wireless.
o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
o Enter the base station network and base station password is necessary.
o Click Update to update the base station with new network settings.
(ref: Page 46 of "Designing AirPort Networks Using AirPort Utility).

HT1998 what is the latest update for Airport Express 802.11n with the Mac OSX10.6.8

what is the latest update for Airport Express 802.11n with Mac OSX 10.6.8?

You can find out as follows:
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click the AirPort Express
Click Manual Setup
Click directly on the word Version (3rd line)
If there are any updates, you will be notified.
If there are not any updates, you have already have the latest firmware.

About My New Apple Airport Express 802.11n Wi-Fi Router

Yesterday on Saturday after i finshed work I Went out & Bought a New Apple Airport Express 802.11n Wi-Fi Router for My Apple iMac Computer & for My Apple iPhone 5 & Apple TV & I Set it up & everything & everything worked out well so i had a question about it, that Green Solid New Light on Apple Airport Express is it suppose to always stay on even if my Apple iMac Computer is Sleeping like other Wi-Fi Routers??? cause i'm wondering cause it looks Very Nice & White & Shiny & New & i don't really want it to Fail on me cause i do like it & it does not take up a lot of space witch is a good thing so just had to ask???
how many years will My Apple Airport Express Wi-Fi Router will last for since it's as Big an an Apple TV, just was wondering if this thing is really strong & stuff to like hold out for years time maybe???
will My Apple Airport Express Wi-Fi Router Software ever get Outdated like my other Wi-Fi Router??? & they stopped making that Belkin Wireless n Router that i had & they stopped Updating it's Software & then The Software became not usable at all so I Had to go out & buy an Apple Airport Express 802.11n Wi-Fi Router.

Hi Byron,
on the first question: take a look at your manual; I have a different router, and on it the light stays on all the time, but I don't know if the Airport works the same way. On mine, it simply means that it is on and ready in case you need it. You should worry when there is no light, LOL.
Second question: with electronics, can't tell at all how long they will be good for. They are made to be compatible with a certain range of devices and software - and will be updated for a while when those devices and softwares are updated. After a while, too many new routers are available with too many new features that are compatible with new devices and softwares, so it's not worth updating the old ones. It's a question of money - they don't want to give you free updates forever, they want you to buy a new piece of equipment.
Third: yes, it will at some point. Everything technology/electronics related is outdated - some very quickly: you buy a new one and the next week you see an ad for a "new, improved" one. Same principle: they want you to buy again.

WRT160NL and AirPort Express 802.11n Connection

I have a Linksys WRT160NL that is currently connected to 2 Apple AirPort Express 802.11n via WiFi.
The connections are Cable Model via ethernet to WRT160NL
WRT160NL ethernet to PCs running XP and Vista
WRT160NL WiFi to laptops at 802.11g
WRT160NL ethernet to DirecTV HD Box
WRT160NL WiFi to Airport Express to ethernet connection of DirecTV HD Boxes (2 connections) (802.11g)
This current setup works. The hard wired components work as expected and the wifi to the AirPort Expresses work as well. The only issue I have is that the AirPort Expresses are only connecting to the the WRT160NL via WiFi at 802.11g speeds. I want to be able to conenct the AirPort Expresses at 802.11n speeds as I am having some streamin issues for High Def video. I verfied in the DHCP Client Table of the router that the AirPort Exresses are connected via "Wireless-G" to the routers. The AirPort Expresses are running the lastest firmware from Apple and I am running Firmware Version: 1.00.01 B17 on the router.
Any help/ideas on how I can connect the Apple Airport Express to the WRT160NL at 802.11n speeds? Are these 2 devices just not compatible with each other?

Thanks for the reply Scrooge. I have verified that the Apple Airport Express is 802.11n complaint:
http://store.apple.com/us/product/MB321LL/A/AirPort-Express-AirTunes?fnode=MTY1NDA0Mg&mco=MTA4NTc4MTE
I have also checked to make sure tha the router is set to Mixed mode:
Mode:     Mixed
Network Name (SSID):     xxxxxxxxx
Channel Width:    Standard - 20MHz Channel
Wide Channel:    N/A
Standard Channel:    2
Security:    WPA2 Personal
SSID Broadcast:    Enabled
The airport expresses are still connected at 802.11g according to the DHCP Client Table from the router. Is there any way to force the Airport Expresses to connect at 802.11n?
TIA

AirPort Utility doesn't support my version of AirPort Express 802.11n

I have OS X Yoesmite installed and now my AirPort Utility doesn't support the version of AirPort Express 802.11n . Any advice?

AirPort Utility 6.3.4 in Yosemite does support both versions of the 802.11n AirPort Express.
What is the model number of your AirPort Express? If you are not sure, look on the side or bottom of the Express. The model number starts with an "A" followed by four numbers.
Hard to see the model number.....you may need a magnifying glass and good lighting.

Airport Express 802.11n will not hard reset or firmware.

Similar Messages

Maybe you are looking for