Airport Express, Airport Admin 4.2 and Windows Vista

If you, like me, have bought a Airport Express and cant get Airport Admin upgraded to 5.2 (which supports vista), you can still make it work.
Start by resetting the Airport express to factory defaults, by pressing and holding in the lill button on the back.
1. if you to get the airport express with a secured wireless network, temporarily connect the airport express to your router with a ethernet cable.
2. log onto your routers administration interface, and look for the DHCP section, which should tell you which ip's have been delegated. Figure out which one is your airport express.
3. When running the Airport Admin Util, in the base station chooser, select "choose other" from the Base station menu. And put in the ip of the airport express and use the factory default password "public"
4. now your connected, change the password, configure the device and unplug the ethernet cable.
5. done

Welcome to the discussions!
Firmware 6.3.x on the AirPort Express was only used in the b/g units. As you have discovered, you won't be able to upgrade or update this device to 7.3.x because it will not accept the firmware.

Similar Messages

How can i run AirPort Express for both a Mac and Windows 2000 SP2?

I have my AirPort Express set up for my iMac and it runs fine. We have a house guest who has a laptop running Windows 2000 SP2. Can I set up Airport so that both computers can access internet wirelessly?

Just did a quick check of the Unofficial Averatec Support Forum. Several posters there upgraded the driver for the wireless card to support WPA on the 5110.
They used drivers from other computer manufacturers and indicated that Averatec has not provided updated drivers.
They were running XP SP2.
Many Averatec models have weak wifi cards. Mine included. Sorry I am unable to be of more help.
Good luck
susan
iBook G4 Mac OS X (10.3.4)

Cannot configure and connect to Airport Express Base Station Model A1264 with Windows 7 (x64)

I am not able to connect Airport Express Base Station Model A1264 with Windows 7 (x64). I did a factory reset, uninstalled and reinstalled the AirPort Utility for Windows v. 5.6.1.
My objective is to extend a non-Apple WiFi network with Airport Express Base Station Model A1264 and use it for direct ethernet and/ or wireless connection. Any guidance as to how I can get set up here?

This is very common, we run a mix of mac and various pc brand desktops and laptops, what I have found is that using the windows wireless client rather than manufacturers on some laptops helps, getting the latest wireless drivers from the manufacturer has helped, make sure all your windows updates XP and Vista are current.
If all the above is covered try the different WEP WPA WPA2 variants or even without for test purposes. I have most success with WPA2.
Finally I am assuming your running the latest firmware on the express unit, whilst this hasn't attributed to better connectivity for us I did it regardless.
Message was edited by: Fence Rider

HELP: Airport Express Base Station over PPPoE and Static IP

Hi there,
I recently purchased a Airport Express Base Station after doing some preliminary research as to wether it would work with my Windows XP Machine.
After finally acquiring it today, I have been trying to set it up with ZERO luck so far.
I open the neat package and plug in the wires as mentioned in the manual and get the AE on. I install the AE software from the CD, my computer recognises the wireless network, all going well.
I setup the airport express using the setup assistant for windows and then open the Airport admin utility. Now here is where I come across the first stumbling block.
My ISP provides each end user with LAN connectivity(primitive), what they do is install a router in every apartment complex and then provide internet through LAN connectivity to every apartment. In doing this they assign each users network adapter a static IP alongwith a lock-in for the MAC address for the specific adapter.
So if you have to change network adapters you have to call them, they release the lock temporarily and you can connect using another adapter without issue.
Another thing they also provide is a Username/password for every apartment user to be able to access the internet once connected. I am not a expert but I am guessing that is what they call PPPoE.
Now I have been trying to setup my Airport Express using the admin utlity but I discovered that it is not possible to specify a Static IP and use PPPoE both together.
How do i get this to work now? .. In addition I have a HP 1010 USB laserjet which I would like to share using my AE, I am guessing I can just create a TCPIP Port for this with the IP of the AE and it should work.
Please help, really require to get this working ASAP with 3 windows machines (2 laptops and 1 desktop)
Many thanks

The Airport Admin utility internet TAB reads as follows
Connect Using Ethernet
Configure TCP/IP using Ethernet
Configure Manually
IP Address: 192.168.3.170
Subnet Mask: 255.255.255.0
Router Address: 192.168.1.1
DNS Servers: blank
blank
Domain Name: Blank
WAN Ethernet port: Automatic
The Network Tab reads as follows
Distribute IP Addresses [CHECKED]
Share a Single IP Address (using DHCP & NAT) [CHECKED]
Use 10.0.1.1/24 addressing [used option]
No other options checked on this tab.
The IPCONFIG reveals the following
===========================================================
C:\Documents and Settings\TAPAN>ipconfig
Windows IP Configuration
Ethernet adapter Wireless Network Connection:
Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 10.0.1.3
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 10.0.1.1
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 192.168.3.170
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
==========================================================
Ethernet shows up here because I am using the internet on my computer directly right now.
But the AE is connected and printer and Airtunes is working fine. It still flashes Amber though.
Any other details you require to further analyse the problem? .. I have tried various combinations of basic IP settings. Resets to the AE, restarts to the Computer already. But I am willing to follow any additional instructions you might have for me and provide you any other information you might require.
Many thanks, You should realise that your continuing support is very encouraging and means a lot to me.

Newbie: Airport Express, DSL internet, G4 iBook, and me

Hello everyone!
I have just purchased an Airport Express (with AirTunes), to connect to the internet wirelessly. I have the latest generation g4 iBook (before they switched to the new MacBook models), and so it came installed with an Airport card, software, etc.
I connect to the internet with a DSL modem, and normally I would connect to the modem with an ethernet cable.
I am having trouble setting up the Airport Express so it can connect to my ISP, and I'm not finding the right place to enter my ISP login information (username and password).
Can anyone help with this? I've tried the Airport Setup assistant, but it didn't work!
Many thanks to everyone!

rdisanto, Welcome to the discussion area!
Does your ISP use PPPoE for the connection? If so, configure the AirPort Express (AX) to use PPPoE and you will be able to enter that information.
You will find this on the "Connect using:" drop down menu on the Internet tab in the AirPort Admin Utility.

Airport Express Can't Connect on a Windows XP Machine! PLEASE Help!

I recently purchased an Apple Airport Express. In my household we have four computers, 3 Mac's and 1 PC. I set it all up, and of course, the PC can't connect to the Airport Express.
So you probably ask yourself why I haven't gone to iFelix's site yet. I have, many, many times tried to do what he says. Doesn't work at all, no matter which way I put it.
I got the equivalent key and everything and it still doesn't work on the PC. Honestly, I have no idea what to do and I'm getting extremely frustrated. PLEASE help me! I don't even know where to get started anymore.

For what it is worth, I just spent the last two days trying to get a brand new Airport Extreme (N/gig) and Airport Express working at home with many Windows XP and WDS problems. I also couldn't get my PSP to connect via WPA.
I have a Cisco 1200 AP working with b/WEP, but bought the Apple products to move to G/N/WPA and bridge from my office (DSL location) to wired devices in my living room. AirTunes was an anticipated plus. I started out with WEP "transitional" as my Extreme security setting.
At first my work laptop (XP with Funk Odyssey WiFi client SW), an old PocketPC and Wii were the only things that would connect to the Extreme base station. My PSP would work, but only via WEP. Our two other wireless XP devices would see the new network but would seem to fail at encryption. I also could not get the Express to connect with the Extreme for WDS.
Switching from WEP "transitional" to WPA/WPA2 Personal did the trick. The two other Windows XP devices worked all of a sudden via WPA, and the WDS/bridging to the Express kicked in. The bad news is the PocketPC only supports WEP, but all the other devices (including two XP devices) worked without a problem. (Hmmm... I think my Nintendo DS also only supports WEP...)

Hey, I have a AirPort Express Base Station ( 2nd Generation ), and I wanted to ask that if I join my network at home with the Express Station, will it still run the 2.5 GHz and the 5.0 GHz?

Okay, well I have just bought a AirPort Express Base Station ( 2nd Generation ) and I'm new to it, but I wanted to ask that if it join's a network you have setup at home, will it still run with the 2.4 GHz and the 5.0 GHz.

The AirPort Express will "extend" both the 2.4 GHz and 5 GHz networks and provide more wireless signal coverage when it is connected to another Apple AirPort router and configured correctly.
The AirPort Express cannot provide more wireless coverage though, if you are trying to connect it to another 3rd party wireless router using wireless only.
It should be possible to set up the Express to provide more signal coverage if you connect it back to the main router using a wired Ethernet connection or using Ethernet powerline adapters.

HT4587 I downloaded Airport Express Utility 5.6 to get my Airport Express to work with the latest Mac OSX 10.7.4, but when I install and run it, it still says my Airport Express is out-of-date and needs the 5.6 utility.

I downloaded and installed Airport Express Utility 5.6 to get my old Airport Express to work with the latest Mac OSX 10.7.4, but when I install and run it, it still says my Airport Express is out-of-date and needs the 5.6 utility. What's up?

It is likely that you downloaded AirPort Utility 5.6.1. If you checked the requirements, this only runs on Leopard or Snow Leopard Macs.
You have Lion, so you need AirPort Utility 5.6 for Mac OS X Lion

I just bought an airport express. i set it up and was able to be detected by my macbook, but i still cant connect wirelessly. the same goes when i tried my iphone. please help!

i just bought an airport express. i set it up and was able to be detected by my macbook, but i still cant connect wirelessly. the same goes when i tried my iphone. please help!

Is the status light green?
Your Airport device may be in Bridge Mode.
Airport Utility 6:
Open Airport Utility, select the Airport Express and click Edit. Navigate to the Network tab and change Router Mode to DHCP and NAT. Then click Update on the bottom right.
Airport Utility 5:
Open Airport Utility and click Manual Setup. Navigate to the Internet icon and change Connection Sharing to Share a Public IP Address. Then click Update on the bottom right.

Clicking sound originating from Airport Express firmware 7.5.2 and later

Hello,
I have submitted a bug report through Apple Developer Connection (I am a registered developer). By posting this here I want to get support for our case: Make Apple fix the Airport Express firmware.
Summary:
The Airport Express device has a bug which appeared first in version 7.5.2. It produces a "clicking" sound when using AirPlay to transport music from an iPhone or a Mac, when certain frequencies are being played. This is not depending on the attached amplifier or headphones, digital or analog output, network settings (network created by Airport Express or not), Mac or iPhone used, audio cable or power supply involved or due to bad quality of the sound file played. The problems are not there when audio is played directly from a Mac or an iPhone through headphones or optical out. We and my colleagues (developers and audophiles) have ruled out all the other options. The problem boils down to a change in the Airports firmware starting with 7.5.2. In 7.4.2 the clicking sound is not there.
Steps to Reproduce:
Play the following song via AirPlay on an Airport Express device having firmware 7.5.2 or higher. The Airport Express being used in our tests is the model produced from March 2008 – June 2012. Attach high fidelity headphones (like Bowers & Wilkins P5, which we used) to Airport Express. Alternatively use a very good amplifier/loundspeaker setup. We also reproduced the bug for example on an Onkyo A-9070 amplifier with both optical and analog connection - there is no difference there. The loudspeakers we used are passive Dynaudio X12.
Play track no. 6 from the "Songs without words" album: http://itunes.apple.com/de/album/lieder-ohne-worte-op.-67-no.-2/id209380163?i=20 9381206
Listen to this solo piano piece carefully for at least 40 seconds. You will notice a clicking sound with high frequencies. This clicking is *not* there in firmwares 7.4.2 and earlier.
Expected Results:
Perfect audio quality as in firmware 7.4.2 and earlier.
Actual Results:
Reproducible clicking sounds in high frequencies.
Regression:
This problem appeared first in Airport Express firmware 7.5.2 and has not been fixed yet. It can also be observed in the current version of Apple TV (as of September 16th).
Notes:
This issue, while not being recognized by the casual listener, makes AirPlay unusable for critical listening - at least when using any firmware after 7.4.2. I would love to use the current firmware (which produces a much more stable connection), but I (and other audiophile AIrplay users) would love to see this issue fixed first.
Here is a thread that concludes - as we did - that Airport firmware 7.5.2 and later is the source of the problem. It is not the hardware, neither Apple's, nor the connected devices:
https://discussions.apple.com/message/17296916#17296916
Hope this helps!
Best,
Gabriel

I'm having the exact same problem. As a classical music lover, this is driving me nuts. It's especially noticable in soft passages in the music, when the volume is turned up high. When the dynamics increase, the little pops/clicks appear (they sound a bit like static noise, as someone stated earlier in this thread). It happens at irregular intervals. When you play pop music, the clicks will disappear (drown) in the music. But for true audiophiles who listen mainly to jazz and classical music this is a severe problem.
I have checked everything and it's definitely an airplay issue. My apple lossless files are 100% okay and play without any problem, except when streamed via airplay. Also, it makes no difference whether you use the analogue or the optical ouptut from the airport express.
I've created a sine frequency sweep myself in Adobe Audition, from 20 Hz up to 20000 Hz with a duration of 25 seconds and a level of -6 dB.
When played through airplay, the clicks always start to appear after 4 seconds in the sweep, only to disappear at 23 seconds.
The clicks manifest themselves at different volume levels. To my ears, they make the same sound as when you change the volume in iTunes when streaming music through airplay. Only when you set the volume in iTunes extremely low, the clicks will disappear.
Apple engineers should use a frequency sweep to recreate the problem, as this is very revealing.
PS: file format isn't an issue here. I've converted the Apple Lossless file to MP3, and it makes no difference at all.

Hi, I`d like to connect my Ipad wirelessly to a stereo to listen to my music from the iTunes library on streaming, but also to movies online, games, Goear-) and so on. I guess I can do that using an Airport express connected to the stereo and via airplay

Hi, I`d like to connect my Ipad wirelessly to a stereo to listen to my music from the iTunes library on streaming, but also to movies online, games, Goear…) and so on. I guess I can do that using an Airport express connected to the stereo and via airplay to my Ipad. My question is, can I listen to all the audio that come out from the ipad (movies online, games, Goear…) or only to the music from iTunes library? I`d appreciate any help. Alex.

My question is, can I listen to all the audio that come out from the ipad (movies online, games, Goear…) or only to the music from iTunes library?
On the iPad you can stream videos, photos, or music from the Video, Photos, Music, and YouTube apps to an Apple TV OR just stream music to an AirPort Express Base Station.

I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn't support this base station. Go to AirPort Service and Support for more information."

I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information." Any thoughts?

This sounds as if you have an older AirPort Express that is no longer supported by the newer Mavericks operating system.
To check and see if that might be the case, locate the model number on the side of the AirPort Express. It will start with an "A" followed by four numbers. Hard to see in the faint print.....so you may need reading glasses or a magnifying class to see the model number clearly.
Model numbers A1084 and A1088 of the AirPort Express are no longer supported by AirPort Utility in Mavericks.
You will need to use a Mac running Leopard, Snow Leopard, or a PC to be able to administer the older AirPort Express.

HT1218 My airport express is 10 years old and I get the message that this version of airport utility (6.2) doesn't support my base station? What to do?

My airport express is 10 years old and I get the message that this version of airport utility (6.2) doesn't support my base station? What to do?

What to do?
Two Options:
1) Buy a new AirPort Express, which will be supported.
2) Try a workaround....not supported by Apple.....to install AirPort Utility 5.6 on the Mac using the Mountain Lion operating system and use the 5.6 application to administer the old AirPort Express. See this thread for more details:
https://discussions.apple.com/message/21397085#21397085

Had a Airport Express connected to my stereo and it was working. I brought an Airport Extreme and suddenly it took over and Airport Express stopped working and disappeared from Airport Utility. What I am supposed to do? ar2ro

I have an Airport Express connected to my stereo and it was working without any problem.
Recently I bought an Airport Extreme to use it as my Base Unit connecting it to my DSL.
I followed the instructions of the Airport Utility, and it started working.
Suddenly, problems started happen the Airport express that was connected to the stereo , stopped working and it disappeared from the Airport Utility area , as it did not exist in the network. I tried to reset it but it did not appear in the Airport Utility page.
Apparently I have other problems with the private network that it created because I cannot use it because of problems with the password that was created. I can only use the network that I created for my guest...
I dont know if my problem is a configuration problem or there is problem with the equipment.
I read that other users where having the same problem with the Airport express , using non apple equipment as their base unit , but I thought that using the Airport Extreme was going to be compatible and no problems would happen.
What should I do?

Common Problem. Common solution.
Connect your Express via ethernet cable to the Mac while other network connections on the Mac are switched OFF.
After the Express shows up, change the settings of the Express to join the existing network. Take the appr. settings.
Unplug and reconnect your Mac to the network.
Check if the Express shows up in Airport Utility
Alternative solution:
Hardreset the Express to factory settings
(while on power push the Pin next to the audio plug with a paperclip. Plug out the Express still holding down the little button then replug the Express to power and release button)
After that, the Express will show up in the Airport Utility.
Make all needed settings.
I would prefer the first solution, its easier just to plug a cat5 cable.

MacBook Pro that my Airport Express WiFi profile was created crashed. Can i reset the Airport Express either to an iPad or Windows 7 computer?

MacBook Pro that my Airport Express WiFi profile was created crashed. Can i reset the Airport Express either to an iPad or Windows 7 computer?

Get the Airport Utility for the your iPad from the App store. You will need to know the password for the Airport Express (not the WiFi password) to access the AE. The iPad utility will, I think, do all of the actions to control your AE.
You can reset the AE back to factory default but with the iPad app you should not ned to.

Airport Express, Airport Admin 4.2 and Windows Vista

Similar Messages

Maybe you are looking for