Airport Express and Firewall
I have the most recent firmware on my Airport Express and have recently installed McAfee Security Center. When the Firewall is on, I can't access my remote speakers. When it is off I can. I have:
Added the IP address of the Airport Express as a trusted IP.
Added complete access for iTunes, Bonjour, and Airport Base Station Agent
Added access to UDP port 5353 for Airport discovery
Added ROAP access for ports 5000, 6000, and 6001 (just for good measure)
Added access to ports 42000-42999 for Radio Streaming
Added access to ports 554 and 7070 for RTSP
The problem remains. Firewall off - it works. Firewall on - it doesn't work.
Any thoughts?
Before one of the last updates, I could access external HD via Airport USB. Now I cannot. Before updates, I could not access the 2 printers via AP USB; now I can. I makes no difference when I turn off firwall. All 3 devices go into USB hub. My computer does not recognize that there is an ext HD. Any suggestions??
Similar Messages
-
Airport Express and Flashing Yellow - Please Help!
I just purchased an Airport Express and cannot get anything the status indicator to flash anything other than a yellow. I am working on a Win 7 64 bit platform and my router is Netgear N600 (model WNDR3700). The only changes I made to the router is via its utility to enter the Airport ID MAC address into the Netgears "Wireless Acces List". I deperately need input on what I might be doing wrong or need to do to my router's setup. Below are what I have tried and status info:
What I have tried:
1) Entered the AIrport's MAC address into my Netgear Router's "Wireless Access List", as well as the Ether ID (out of desperation).
2) Installed on my PC the latest version of the Airport Utility (5.5.3).
3) Plugged the Airport directly in port 4 of my Netgeat Router.
4) Changed ethernet cables.
5) Reset the Airport.
6) Rebooted the Netgear and my PC.
7) Plugged the ethernet cable from the modem directly into the Airport.
Info:
1) When the Airport is first turned on (ethernet is already plugged in), the status light turns solid greem, then goes to solid yellow for a bit, and then immediately goes to flashing yellow (approx 2 seconds between flashes) and stays that way.
2) then If I run my Advanced IP Scanner if shows the Airport, an IP of 192.168.1.20, the Airport's ethernet MAC address. The status shows "Ok".
3) If I unplug the Airport and click rescan on the IP Scanner the device remains present but the status is changed to "Dead".
Despite what I tried I get only get the yellow flashing light? Do I have a bad Airport Express or is this a failure on my part to properly set up the Netgear? Thanks in advance for any help offered.The AirPort Express flashing yellow means it it not receiving a valid IP address. This is issued by your router.
I recommend disabling your Netgear's "Wireless Access List" until you get it resolved.
One thing that you did not mention is using AirPort Utility. You need to configure the Express using AirPort Utility for Windows. If you don't have that click here: http://support.apple.com/kb/DL1391
Read about designing AirPort Networks here: http://manuals.info.apple.com/en/designing_airport_networks_10.5-windows.pdf
A new Express creates an unprotected wireless network named "Apple Network xxxxx". You need to disconnect from your existing network and connect to that network in order for AirPort Utility to communicate with the Express. Most likely you will have to temporarily disable any and all anti-virus / firewall / security software running on your Windows to do this. If you don't see that network you will not get anywhere.
When you are finished configuring the Express in AirPort Utility, including addressing any unresolved conflicts it may report, click the button to restart it. AirPort Utility will say "the Express is now restarting" but the temporary network that it created for you to configure it will cease to exist, so just close the window. Reconnect to your usual wireless network which will now welcome the Express as a member.
After it restarts the Express should show a happy green light.
When you are finished re-enable all your Windows firewalls and AV software. -
I have installed airport express on my Window 7 and had problem to find the airport express.
I solved the problem by turning off my AVG firewall and the airport tool found the airport express and it went steady green.
I then turned on the AVG firewall again and it continues ok.
But when I turn off and restarted my laptop I have to follow the same procedure.
The AVG firewall is set to All Allowed for the airport express.
Is there anybody out there that can give assistance to solve this problem?Hi,
I solved the problem myself by updating the Wi-fi driver.
Now it works perfect. -
Airport Express and Apple TV not seen by new computer
I have two airport expresses (both A1084 wireless g) and an Apple TV (a couple years old). I have the latest version of iTunes and the latest version of Airport Utility. My new computer is a PC running Windows 8. Everything worked fine until last week when my old computer failed (it was a PC running Vista). I got the new machine up and running and for a little while the computer could see the airport expresses but never did see the apple tv. Then it stopped and that was that. I shut everything down, restarted everything, uninstalled and reinstalled Airport Utility, uninstalled Airport Utility again and reinstalled an older version, that didn't work, upgraded to the new version of Aiport Utility and that still didn't work. My wireless network is fine, my iPad can connect, the new computer can access the internet fine. My old windows xp computer that is on its last legs can see the two airport expresses and the apple tv. But this new computer which is the one that is supposed to take care of all this for me can't. Any suggestions because I'm at my wits end.
i'm assuming that the Airport Utility app for your ipad sees them? I wonder if Win8 has a firewall active that is blocking the ports.
-
Need help with Airport Express and so on.
Ok so my main problem before getting into what I need help with here is that our MacBooks and now my iPhone 6 plus isn't staying online. Keep getting booted off and then I either have to select the network again or it will eventually go back on. If anyone has a solution or so please feel free to answer that as well. I'm running on Roadrunner with a Netgear 600 wireless router and a motorola modem. Both of which I'll leave the link to below for a better look.
My Main Question: So I'm looking at a new wireless router mainly and possibly a new modem. I know Apple products are trustworthy but how good is the Airport Express and other Airport products. Also what is the Maximum speed and Maximum data speed for the cheapest express station and if anyone knows the speeds of the other devices it would be greatly appreciated.DSL Router to Netgear 5-port Switch and I used the switch to connect to Airport Extreme, TV, Blue-Ray DVD player and DirecTV Receiver.
The AirPort Extreme base station (AEBS) is a router so it will do what you need.
You need to reconfigure your setup. Connect the WAN port of the AEBS to the DSL router. Then connect the Netgear switch to one of the LAN ports on the AEBS. The AEBS will properly share the connection. -
I have an airport express and want to know how to set up two different wireless networks. One with 5GHZ and one with 2.4GHZ so different devices can connect to either. I have an iphone 4 that will not connect to 5ghz.
thank you!Your AirPort Express is already providing two separate 2.4 GHz and 5 GHz bands, but each band is using the same wireless network name.
This is the default setup for the AirPort Express, which is recommended for most users. The theory here is that devices will automatically connect to the best quality signal based on their capabilities and distance in relation to the AirPort Express.
It is possible to assign a different name to the 5 GHz band, and then "point" devices at that network to connect. Some users swear by this option.....(I am not one of them).... but you might want to give it a try to see how it works for you.
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Express
Click Edit in the smaller window that appears
Click the Wireless tab at the top of the next window
Click Wireless Options near the bottom of the next window
Enter a check mark next to 5 GHz Name.....which will automatically add "5 GHz" to the network name....so you can identify it
Click Save, then click Update and wait a full minute for the Express to restart
Now you will need to "point" your 5 GHz capable devices at the 5 GHz network name. 2.4 GHz devices will connect to your "other" network name. -
I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work? And one more thing about the setup, the linksys router shich acts as a base is in a different room as the airport express which i wanted to use for airplay. So I'm hoping to hook up the Airport express via wireless signal. If i can set it up, can someone pls help me out by posting detailed instructions. Thanks so much!
The first message that AirPort Utility will display during the auto setup will be that the Express will be confgured to "extend" the network. When AirPort Utility analyzes the network further, and sees that the Express cannot "extend" the 3rd party network, the next message will indicate that the Express is being configured to "join" the wireless network.
Once the Express is configured, if you later go into AirPort Utility to check the settings under the Wireless tab, you will see that the Wireless Mode is indeed "Join a wireless network". -
Airport Express and BT Homehub - how can I get it to work?
Hello, can someone help??
I have an Airport Express and a MacBook. My only use for my Airport Express is purely to play ITunes music through my stereo via my MacBook wirelessly. Therefore I only require my Airport Express to join my current network.
I recently changed my phone and broadband network provider from Talk Talk back to BT. My Airport Express worked fine when I was with Talk Talk, I was using a Belkin wireless router for my network connection which worked without any problems. When I got my Airport Express, it was easy to set up - it joined my Talk Talk network without a hitch.
When my connection transferred to BT last week, I tried to connect up my Airport Express to my new BT Homehub. However when I went into Airport Utility my AX wasn't there. So, I read the guide on the Apple Support site and reset it to factory settings. This then seemed to make it 'appear' in Airport Utility, so I went through the process of setting it up as I did when I first bought it. When I got through to the final stage when it is 'Updated successfully and is now re-starting', the AX icon seems to disappear from the left hand side of the box and eventually I get an error message stating 'Airport Utility was unable to find your Apple wireless device after reinstating: The settings for this apple device have been successfully updated but there was a problem re-joining the wireless network or finding the apple wireless device. You may need to select your network from the airport menu and try again' (Incidentally, this last piece of advice doesn't work)... So, I am not sure what to do. I have tried changing the format of the WEP code I need to enter by adding " in front of the code as well as $ as is the suggestion on the Apple Support site...
Is my AX faulty? Is my BT Homehub (The 'next generation of router' as BT call it) preventing my AX from joining my network?? If anyone can help I would appreciate it, I am not very clued up on these things.... :o)
ThanksI have now managed to get AX working on my BT home hub. I took my second non-working unit back to Apple in Solihull and got them to test it in store. They agreed it wasn't working. They then tested another unit in store and that did work so I brought that home. It would be worth you doing the same as I got a 10% discount off my next purchase of anything at Apple for my troubles.
I set my homehub security to None (from WEP - in homehub manager/advanced/wireless/security), plugged in my AX to homehub using an ethernet cable, then ran Airport utility and after a couple of runs it finally picked it up. I was able to set the configurations I wanted and 24 hours later it is still working. I set my homehub security settings back to WEP as soon as the AX was configured.
I also installed airport utility on my son's windows laptop and that is now able to print wirelessly as well. So, finally a result.
I would suggest you take your unit back to where you bought it from and get them to test it. If they offer you another one ask for a Mac genius
to test it in store for you first. Also ask them to run through the installation procedure with you. Don't forget to ask for something for your troubles:)
Hope that helps, -
A Time Capsule, Airport Express and AT&T 2Wire walk into a bar...
Alas, I'm sure this question has been asked before, but my reserach keeps turning up separate answers. So I thought I'd turn to this forum for some advice. Ultimately I'm seeks suggestions on various ways to configure my network to allow easy backups, connection two rooms, and wirelessly print from anywhere.
I have a:
Time Capsule (dual band) - used for Time Machine backups
Airport Express (older)
and new 2Wire 3800HGV-B wireless modem/router from AT&T (for U-verse internet/TV)
My room configuration is:
Living room with TV, internet connected DVD player, and new AT&T 2Wire Wireless U-verse modem
Home office with 2 desktop comptuers (no wireless cards) and a USB printer.
Two roaming laptops which move around the rest of the house
The livingroom and the office can't be connected with a physical wire.
What I was hoping to do was setup my office with the Time Capsule in the office as a wired hub, and then use it as a wirelessly bridge to the 2Wire network. But as I understand it, a Time Capsule can't be used as a bridge to a non-Apple product. Please correct me if I'm wrong.
Alternately I could always get wireless cards for the desktop computers, but this leaves the printer.
I've read suggesitons of people who have used their TC as the primary router, disabling wireless on their AT&T 2Wire, and hooking the two together with ethernet. Others who just join the TC to the 2Wireness network. But really what I'm seeking is a way to join the two rooms.
Any thoughts? Am I asking the right questions or providing the right information?
Much thanks,
dana.So I figured I'd go with an initial suggestion and attached my TC via ethernet to the 2Wire modem/router in my living room, and make the TC my primary wireless router.
Good plan
since both will be in the same room, I assume I need to disable wireless on the 2Wire
Correct
What kind of configuration do I need to do on the TC, or do I just following the wizard and select 'Extend existing network'?
You can follow the guided setup or I can give you a step by step manual setup. In either case, you will configure the TC to "Create a wireless network".
("Extend" is only used if the TC connects using wireless only....you will be using Ethernet from one of the LAN <-> ports on the 2-Wire to the WAN port (world icon) on the TC.
The guided setup will normally sense that the TC is connected to another router and suggest that the TC be configured in Bridge Mode, which is the correct setting. Otherwise, select the Bridge Mode option when it is presented.
Note....If you have a newer dual band TC, the Guest Network option cannot be enabled when the TC is configured in Bridge Mode. So, if you want a "Guest" network, maybe the 2-Wire could provide that service.
Should I attach this (via ethernet) to the TC or the 2Wire?
Pick a LAN <-> port on either one, your choice, whichever is easier
What should the AT&T DVR be connected to?
I'm not familiar with an AT&T DVR, but if it connects via Ethernet, you can connect to a LAN <-> port on either the 2-Wire or the TC
For printing, my plan is to attach the printer through USB to the Airport Express and then connect that wirelessly to the TC network (though my first attempt at this failed to connect).
Suggest that you get the TC up and working smoothly. Then tackle the Express. -
My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network? Network is administered through an iMac running OS X Yosemite 10.10.2. Ideally, would like for the second Airport Extreme hard drive to appear on the list of devices in the Finder window.
Ok.. gottcha
The problem is network wise.. Yosemite is about equal to tin cans and string.. pathetic.
Here is my usual set of instructions to get anything working on Yosemite.
The best way to fix problems is a full factory reset of all the AE in the network.
Factory reset universal
Power off the AE.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the AE to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg AEgen5 and AEwifi for basestation and wireless respectively.
Even better if the issue is more wireless use AE24ghz and AE5ghz with fixed channels as this also seems to help stop the nonsense.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the AE always takes the same IP address.. this is not a problem for AE which is router.. it is a problem for AE which is bridged.. you will need to set static IP in the main router by dhcp reservations or use static IP in the AE which is tricky.
4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric..
5. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
6. Now mount the disk of the second AE in finder... manually.
Use Go, Connect to Server and type in the AE ip address.
SMB://10.0.1.2
Where you will replace that address with the actual address. The network resource should be discovered and then it will request the password.. type that in and make sure you tick to save it in your keychain.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
Do as much as you want of the above... not all of it is necessary.. only if you want it reliable.. or as reliable as Yosemite in its current incarnation can manage.
The most important thing is point 6.. mount the disk using direct IP address and not names.. dns in Yosemite is fatally flawed.
See http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/ -
My airport expresses are not showing up in my internet options. I was trying to change channels between the airport utility and the airport expresses and they didn't reset properly. I then hit "forget" on the options...now they are no longer visible. It's a nightmare. How do I get them back?
There are three Airport resets, soft, hard and factory default. It would probably be beneficial if you tried each one in sequence. Actually, you could jump to the factory default reset if you don't mind reconfiguring from scratch.
-
Itunes freezes when streaming music to airport express and to loewe air speaker at the same time?
Hi,
(first post )
I was recently offered a Loewe Airspeaker. I already had an Airport Express connected to a hi-fi system.
The Airport Express + hi-fi is in the living-room and the Loewe Airspeaker is in our bedroom.
Both are connected to my network via wifi.
I was trying to stream music from my iMac to both the Airport Express and the Loewe Airspeaker.
When doing this, I am able to get the same tune on both devices, but iTunes systematically freezes
=>music continues to be streamed but interface on the iMac gets the endless multicolor wheel !
Has anyone seen anything similar before, for ex. is there a similar issue when streaming music to 2 different Airport Express?
Any idea on where this is coming from?
Any idea on how to prevent this?
Thx in advance
Rodolphe
A few precisions on the configuration:
the iTunes library and corresponding music are located on a Mac Mini configured as a media server.
The iMac connects to the mac mini via wifi (shared folder). Home network is organized via an Airport Extreme.
Both computers run Mac OS 10.7.2 Lion and are up to date.Well, repying to my own post... Might have found the solution: I tried to do the same with a Macbook Pro 2010 using the very same setup. And it worked perfectly! No freeze, no nothing.
One explanation I see:
my iMac is dating back to May 2007, a Core 2 Duo 2,16Ghz with 2 Go of RAM.
So the computer's characteristics (or the Wifi component or the combination of all of this) might be not robust enough to allow streaming to those 2 devices...
Anyone's got anything to add? -
Is Printer HP Laserjet 1018 compatible with Airport Express and windows
I am using HP Laserjet 1018 which is connected directly to the PC.
As it is a USB printer but not a wifi one, can I connect it to Airport Express and will it be recognised ?
Thank you for your answers.Hello TigerParis75,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
AirPort Utility 6.x: Use a USB printer on your Wi-Fi network
http://support.apple.com/kb/PH5114
Just make sure you have all the updated version of the drivers.
Best of luck,
Mario -
The Airport Express is not finding my wireless network. I do not have any of the devices listed below. I have a Belkin wireless router. Can I still use Airport Express ( without plugging an ethernet cable into it) ? Any ideas for how to make it find my network ? It is sitting next to the wireless router-so is in range.
If you already have a wireless network in your home and want to extend its range, AirPort Express can help. Just place it in range of your primary base station — an AirPort Extreme, Time Capsule, or another AirPort Express — and near the area where you want your wireless connection. Launch the easy-to-use AirPort Utility app on your iOS device or Mac, and you’re mere minutes away from long-range Wi-Fi enjoyment.Hi - you can do what you want to do with AirPlay from your iPhone - but unfortunately it is not as easy as the people in the Apple store told you - your first problem is that you have a non Apple router - you cannot extend a non Apple router wirelessly with the Express - you can only join the network and connect an ethernet device to it - you can however connect via ethernet and have it create a wireless network of its' own - you can set this up from your iPhone or the XP - but this is a complicated setup and would involve many different discussion areas of this forum - therefore I would suggest that you use your 90 days of support and consult directly with Apple to do this - go to this link - http://www.apple.com/support/contact/
-
I have bought a new airport express and using it with my macbook (iTunes 10.2.2). I have joined an existing wireless network for internet in my home and with that i am trying to play the music via itunes but there is audio dropouts every 60 secs or so. I am using a set of speakers from kenwood connected to the airport express. The operating system on my macbook is mac os X 10.5.8. i am sure it is not a problem of streaming music online because i have even tried playing music which are stored in my macbook.
Is there any problem with the setting in itunes or quicktime ? Kindly reply...... I am waiting for your valuable suggestion.
Thank you a lot in advance.I am shocked to have found this same AX audio dropout problem starting TODAY, every few seconds the audio just drops for a couple seconds and then resumes: Latest software versions of everything. No iPad, iPhone or Touch. Internet hardwired to D-Link DES1105 (1000baseT Switch) hardwired to new 80211N AX, AX optical to stereo, AX Wi-Fi internet to basic 1st-gen MacBook operating at 80211G, and an older 'G' AX extender at the far end of the house, away from all this. The MacBook streaming iTunes is usually 12 feet from AX. I've used this setup for years of trouble-free AirTunes / Airplay until today. Today I also found 2 very reliable fixes and 1 way to force a dropout, but first, I read some posts and tried ALL following settings one-at-a-time and restored them ALL because NONE of them helped: Turned off IPV6. Streamed to multiple speakers 'Computer' and 'AX' (restored to just AX). Turned off 'Ask to Join new (WiFi) Networks'. Turned off Bluetooth (can't live without Magic Trackpad, so glad that wasn't it). Here's my discoveries: Lo and behold, each time I click the Airport icon in the Menu (you know it shows you've got 4 bars from AX) when the status switches to 'Looking for Networks' for a second it CAUSES the AX audio to drop out for a couple seconds (it never did that before today.) iTunes still playing, streaming, AX laser still lit, but the 'PCM' light on stereo and the sound GOES OUT EVERY time I click the Airport icon in the menubar, just like the regular, annoying dropouts. So, to reduce traffic I quit Safari (3 tabs, no streaming, just Gmail, Google, and Netflix browsing). Lo and behold, the dropouts stopped altogether. No other Web apps going (not iTunes Store, Genius, Ping, nothing), so I launched Chrome to the same 3 tabs and the dropouts HAVE NOT RETURNED. That's right, not only did simply QUITTING SAFARI cure it, and Chrome doesn't contribute to it, but I can demonstrate it just by forcing my Airport to re-scan. Works for me, written using Chrome. The other reliable fix is to hardwire MacBook to the Switch. This is obviously not ideal, but Airplay audio doesn't drop out over Ethernet. Also, in all my tests, it made no difference whether iTunes did the streaming, or Airfoil did.
Maybe you are looking for
-
Why can't I install the 10.5.8 Leopard Combo Update??
I've had the Leopoard 10.5.8 combo update on my computer for a while now, but I haven't been able to install it successfully after at least 5 attempts. Usually, when I restart my computer to install it, the installation remains stuck in "configuring
-
How to download Adobe document service and how to register in Server
From where i can download the ADS (Adobe document service) for the NW CE version .? or for NW 2004s version what is the procedure for refiestering that service in the server? can any body have the idea about where to download and how to regis REgar
-
Unable use AirPlay with ipad2 and airport express. How to make it work.
-
How do I get battery charge % to display on iPhone 3G?
How do I get battery charge % to display on iPhone 3G?
-
Rounding decimals using FM REUSE_ALV_HIERSEQ_LIST_DISPLAY
Hi all. I am having no luck get values to round in FM REUSE_ALV_HIERSEQ_LIST_DISPLAY. I have managed to get them to round in REUSE_ALV_GRID_DISPLAY by setting DECIMALS_OUT to a value of 0. Any help would be very much appreciated. Anthony