Airport Express and Popcorn Hour (or other wired only ethernet device)

I have a popcorn hour media tank that has a wired only ethernet port. Can I connect this to an Airport Express base station, have the Airport Express connect to my existing wireless network, and have the popcorn hour or other wired only ethernet device get out to the internet?
Once again for simplicity DSL>Wireless router>Airport Express>popcorn hour. The setup guide says that I can connect a modem to the Airport express, but it does not say anything about the Airport Express acting as a wired hub. Thanks.

I recently purchased the Airport Express and plugged the SAME ethernet cable into it. Now my Laptop is no longer able to connect to the desktops or printers. The wirelss network works fine. I can get on the internet, just not connect to the other devices.
Why??
Effectively, you created a second network (subnet) when you introduced the AirPort Express Base Station (AX) in the mix. When computers are on separate subnets they have trouble "seeing" each other.
To resolve this, you just need to reconfigure the AX as a bridge.
To set up the AirPort Express Base Station (AX) as a bridge, using the AirPort Admin Utility, connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, make these settings:
Network tab
- Distribute IP addresses (unchecked)
- Apply the new setting.

Similar Messages

Can I use a 2nd Airport Express to bring internet to a wired-only desktop?

Hi.
I have an Airport Express that's working flawlessly as a wireless router via a cable modem. Problem is, I have a second computer ( a desktop PC) that's too far away from the cable modem to hook it up via the ethernet. Is it possible to use a second Airport Express to extend the wireless network and thereby connect to my desktop with the ethernet cord? I guess this would be kind of using the AE backwards. If this is possible, could you please tell me how I might do it?
Thanks so much!

Here are the basic steps in setting up a WDS:
(Note: To facilitate the WDS set up, place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete. Also, jot down the AirPort IDs (not the Ethernet ID) for each of the base stations to be used in the WDS. The AirPort ID and is printed on the label on the bottom/side of the base station.
I suggest that you also perform a "factory default" reset on each of your AXs to get them to their original "out-of-the-box" configuration.
Finally, for this WDS, AX#1 (the AX connected to the Internet modem) will be the main base station, and AX#2 will be the remote base station.)
Main Base Station Setup - AX#1
o On your MacBook Pro (MBP) click the AirPort status menu in the menu bar and choose the wireless network created by AX#1.
o Open AirPort Utility (located in the /Applications/Utilities folder).
o Select AX#1, and then, choose Manual Setup from the Base Station menu.
o Click Wireless in the toolbar, and then, choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
o Click WDS, and then, choose “WDS main” from the WDS Mode pop-up menu.
o Select the “Allow wireless clients” checkbox.
o Click the Add "+" button, and then, enter the AirPort ID of AX#2.
o Click Update to send the new settings to the base stations in the WDS.
Remote Base Station Setup - AX#2
o On the MBP click the AirPort status menu in the menu bar, and then, choose the wireless network created by AX#2.
o Open AirPort Utility if not already running.
o Select AX#2, and then, choose Manual Setup from the Base Station menu.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and then, choose the same channel as the main base station from the Channel pop-up menu.
o Click WDS, and then, choose “WDS remote” from the pop-up menu.
o Enter the AirPort ID of AX#1.
o Click Update to transfer the settings to the base station.
(ref: Pages 42-46 of "Designing AirPort Networks.)

WDS setup with Airport Express and other(non-Apple) wireless router

Hi,
I am trying to configure a wireless network with one airport express and one Planex Wireless access point. Can anyone please point me to the settings to be made for such a scenario? I can use either of them as the main WDS device, and have a (wired)router provided by the ISP in the network.(so total 3 devices : airport, planex a/p , ISP router)
Thanks.

I'm having the same problem, both with a Linksys WRVS4400Nv2, and a WRT54G. I've not put much effort into the WRT, but the WRVS was such a pain that I don't think I can get it to work at all.
The WRT doesn't have a section on WDS, but I've read that it's supported anyways, and nothing needs to be enabled on it. Is there a good step-by-step available here or elsewhere that uses close to the same router and Airport Express units, on the latest Airport setup software?
Basically, I'm trying to set this up for a guy in an ~8000 sq. foot house so he has wireless throughout it, and he wants itunes streaming from the AX. Has anyone done this?
Message was edited by: manderso

HT4437 can i have more than one apple tv at different locations by ethernet on the same router thinking of dumping the airport express and hard wiring an apple tv if this is possible

can two apple tv's be used on the same network and router they would be in different locations one inside the house and one for an outside system? may dump the airport express and go to ethernet wired direct to each apple tv from same router..

Welcome to the Apple Community da dad.
Yes you can connect multiple Apple TV's by ethernet.
What do you mean by outside.

I was told at the Apple store that I could simply plug in ( electric power) the Airport Express and it would find my wireless network. I hoped to use it as a way to play music from my iphone. I do not use other Apple routers etc,

The Airport Express is not finding my wireless network. I do not have any of the devices listed below. I have a Belkin wireless router. Can I still use Airport Express ( without plugging an ethernet cable into it) ? Any ideas for how to make it find my network ? It is sitting next to the wireless router-so is in range.
If you already have a wireless network in your home and want to extend its range, AirPort Express can help. Just place it in range of your primary base station — an AirPort Extreme, Time Capsule, or another AirPort Express — and near the area where you want your wireless connection. Launch the easy-to-use AirPort Utility app on your iOS device or Mac, and you’re mere minutes away from long-range Wi-Fi enjoyment.

Hi - you can do what you want to do with AirPlay from your iPhone - but unfortunately it is not as easy as the people in the Apple store told you - your first problem is that you have a non Apple router - you cannot extend a non Apple router wirelessly with the Express - you can only join the network and connect an ethernet device to it - you can however connect via ethernet and have it create a wireless network of its' own - you can set this up from your iPhone or the XP - but this is a complicated setup and would involve many different discussion areas of this forum - therefore I would suggest that you use your 90 days of support and consult directly with Apple to do this - go to this link - http://www.apple.com/support/contact/

Airport Express and BT Homehub - how can I get it to work?

Hello, can someone help??
I have an Airport Express and a MacBook. My only use for my Airport Express is purely to play ITunes music through my stereo via my MacBook wirelessly. Therefore I only require my Airport Express to join my current network.
I recently changed my phone and broadband network provider from Talk Talk back to BT. My Airport Express worked fine when I was with Talk Talk, I was using a Belkin wireless router for my network connection which worked without any problems. When I got my Airport Express, it was easy to set up - it joined my Talk Talk network without a hitch.
When my connection transferred to BT last week, I tried to connect up my Airport Express to my new BT Homehub. However when I went into Airport Utility my AX wasn't there. So, I read the guide on the Apple Support site and reset it to factory settings. This then seemed to make it 'appear' in Airport Utility, so I went through the process of setting it up as I did when I first bought it. When I got through to the final stage when it is 'Updated successfully and is now re-starting', the AX icon seems to disappear from the left hand side of the box and eventually I get an error message stating 'Airport Utility was unable to find your Apple wireless device after reinstating: The settings for this apple device have been successfully updated but there was a problem re-joining the wireless network or finding the apple wireless device. You may need to select your network from the airport menu and try again' (Incidentally, this last piece of advice doesn't work)... So, I am not sure what to do. I have tried changing the format of the WEP code I need to enter by adding " in front of the code as well as $ as is the suggestion on the Apple Support site...
Is my AX faulty? Is my BT Homehub (The 'next generation of router' as BT call it) preventing my AX from joining my network?? If anyone can help I would appreciate it, I am not very clued up on these things.... :o)
Thanks

I have now managed to get AX working on my BT home hub. I took my second non-working unit back to Apple in Solihull and got them to test it in store. They agreed it wasn't working. They then tested another unit in store and that did work so I brought that home. It would be worth you doing the same as I got a 10% discount off my next purchase of anything at Apple for my troubles.
I set my homehub security to None (from WEP - in homehub manager/advanced/wireless/security), plugged in my AX to homehub using an ethernet cable, then ran Airport utility and after a couple of runs it finally picked it up. I was able to set the configurations I wanted and 24 hours later it is still working. I set my homehub security settings back to WEP as soon as the AX was configured.
I also installed airport utility on my son's windows laptop and that is now able to print wirelessly as well. So, finally a result.
I would suggest you take your unit back to where you bought it from and get them to test it. If they offer you another one ask for a Mac genius
to test it in store for you first. Also ask them to run through the installation procedure with you. Don't forget to ask for something for your troubles:)
Hope that helps,

A Time Capsule, Airport Express and AT&T 2Wire walk into a bar...

Alas, I'm sure this question has been asked before, but my reserach keeps turning up separate answers. So I thought I'd turn to this forum for some advice. Ultimately I'm seeks suggestions on various ways to configure my network to allow easy backups, connection two rooms, and wirelessly print from anywhere.
I have a:
Time Capsule (dual band) - used for Time Machine backups
Airport Express (older)
and new 2Wire 3800HGV-B wireless modem/router from AT&T (for U-verse internet/TV)
My room configuration is:
Living room with TV, internet connected DVD player, and new AT&T 2Wire Wireless U-verse modem
Home office with 2 desktop comptuers (no wireless cards) and a USB printer.
Two roaming laptops which move around the rest of the house
The livingroom and the office can't be connected with a physical wire.
What I was hoping to do was setup my office with the Time Capsule in the office as a wired hub, and then use it as a wirelessly bridge to the 2Wire network. But as I understand it, a Time Capsule can't be used as a bridge to a non-Apple product. Please correct me if I'm wrong.
Alternately I could always get wireless cards for the desktop computers, but this leaves the printer.
I've read suggesitons of people who have used their TC as the primary router, disabling wireless on their AT&T 2Wire, and hooking the two together with ethernet. Others who just join the TC to the 2Wireness network. But really what I'm seeking is a way to join the two rooms.
Any thoughts? Am I asking the right questions or providing the right information?
Much thanks,
dana.

So I figured I'd go with an initial suggestion and attached my TC via ethernet to the 2Wire modem/router in my living room, and make the TC my primary wireless router.
Good plan
since both will be in the same room, I assume I need to disable wireless on the 2Wire
Correct
What kind of configuration do I need to do on the TC, or do I just following the wizard and select 'Extend existing network'?
You can follow the guided setup or I can give you a step by step manual setup. In either case, you will configure the TC to "Create a wireless network".
("Extend" is only used if the TC connects using wireless only....you will be using Ethernet from one of the LAN <-> ports on the 2-Wire to the WAN port (world icon) on the TC.
The guided setup will normally sense that the TC is connected to another router and suggest that the TC be configured in Bridge Mode, which is the correct setting. Otherwise, select the Bridge Mode option when it is presented.
Note....If you have a newer dual band TC, the Guest Network option cannot be enabled when the TC is configured in Bridge Mode. So, if you want a "Guest" network, maybe the 2-Wire could provide that service.
Should I attach this (via ethernet) to the TC or the 2Wire?
Pick a LAN <-> port on either one, your choice, whichever is easier
What should the AT&T DVR be connected to?
I'm not familiar with an AT&T DVR, but if it connects via Ethernet, you can connect to a LAN <-> port on either the 2-Wire or the TC
For printing, my plan is to attach the printer through USB to the Airport Express and then connect that wirelessly to the TC network (though my first attempt at this failed to connect).
Suggest that you get the TC up and working smoothly. Then tackle the Express.

Best way to set up homesharing via airport express and NAS

Hi,
I've just bought an Airport express and was wondering what the best way to set it up would be so that I can play music stored on my NAS, controlled by my iphone / ipad. I have itunes match as well, and don't want my phone to be streaming the music from wherever. The airport express will be wired via ethernet to the same router as the NAS on which everything is stored. I don't want the problem with network dropouts and hammering the bandwidth and battery on my iphone to deal with.
How can I set it up to be taking the music straight from the NAS rather than streaming it. I'd also rather not have to turn off itunes match everytime, because it takes an age to repopulate the library when I turn it back on.
Thanks,
Dom

You cannot use homesharing to play content from anywhere but iTunes on a computer. The content doesn't have to be on that computer but it has to be part of the iTunes library on your computer. In addition the computer has to be on with iTunes running.
It doesn't matter what sonos can do, sonos is a lame duck in comparison to iTunes because iTunes gives you many features sonos can't, all because it doesn't use iTunes and homesharing.

Extending network with Airport Express and Airport Extreme (latest models) causes chaos on network

Today I upgraded from my several year old Airport Extreme (3rd gen) and 2nd gen Airport Express to a new (what you'd buy on the shelf today) Airport Extreme and Airport Express. All airports are updated with the latest firmware and I'm using windows 7 for configuration.
The intention is to use the Airport Extreme as the main router, also serving wifi. And extend the network using the express. As such, the following has been done:
The Airport Extreme is configured for automatic channel, and automatic radio mode. I tried to select 802.11n 5 ghz and 802.11 n 2.4 ghz only, but it won't take the changes. Additionally, it wont' accept me using only channel 6. Not sure why, but I digress. The airport extreme is not set to broadcast a separate name for the 5ghz network.
The Airport Express is configured to use bridge mode, use an existing wireless network and is connected to my network on it's WAN port (the circle icon on the back) with ethernet. The password and wireless name used in configuration is the same as created initially on the Airport Extreme.
Initially I did the configuration of both airports on my computer, connected by ethernet to ensure stable connectivity while I inputted settings. During this, they appeared to accept the changes fine. However, when I moved the airport express to it's destination (other side of my house), the entire network went crazy.
Internet became slow, and often wouldn't load pages. This was on wired and wireless connections. When I attempted to administer the Airport in the Utility, they would not load, an error would occur. Also, at one point the Airport Extreme had renamed it self with a (2) at the end. Which was super odd. So far, the only solution has been to unplug the Airport Express and attempt to devise a solution.
Anyone have any ideas? Of course, I will continue to tinker with this, but it seems realllly strange. The previous setup was also extended (granted, using wireless only, not ethernet > wireless) and worked fine, granted it was a smidge slow, but it worked.

I wanted to add this.. I followed the guide here: http://support.apple.com/kb/HT4260 to extend using ethernet, and the above is the result.
I just tried re configuring in OS X Mavericks and got the same, odd, result.

I've extended my Time Capsule wifi via Airport Express and the download speed is still super slow

I get an average of 80Mbps download speed when close to the Time Capsule. When I got upstairs in the house the download speed drastically drops. So I decided to extend the wifi range using an Airport Express. See image below. I've placed the Express router upstairs in the house and when I stand close to the Express I get a very slow download speed. About 7Mbps. Even slower than when I hadn't "extended" the range. What's going on...?

I've placed the Express router upstairs in the house and when I stand close to the Express I get a very slow download speed. About 7Mbps. Even slower than when I hadn't "extended" the range. What's going on...?
Well, the first rule that you need to remember is that when you "extend" using wireless.....you will have a drop in the potential speed on the network. So, while you might have more "range" for the network, the network speed will drop. Nothing that you can really do about that other than connect the Time Capsule and AirPort Express using a wired Ethernet connection. There will be no speed loss over the Ethernet cable, so the Express should deliver approximately the same speed as the Time Capsule.
The next rule is that when a device "extends" using wireless, it can only extend the quality and speed of the signal that it receives. A speed "boost" will not appear.
Try locating the Express about half way between the Time Capsule and the area that needs more wireless coverage. Anything that you can do to minimize obstructions between the Time Capsule and Express and on to the other area will help.....but you will never get close to the performance of connecting the AirPorts using an wired Ethernet cable.
Unfortunately, Apple really doesn't tell you very clearly, if at all, about important things like the two rules above.

HT1145 I have an older plug in version of Airport Express and am trying to connect it to my wifi network to boost coverage but it is not connecting to my network.

I have an older plug in version of Airport Express and am trying to connect it to my wifi network to boost coverage but it is not connecting to my network.

What is the make & model of the wireless router that you are trying to "boost" with the AirPort Express? Is your Express an 802.11g or 802.11n model? Is the connection between routers going to be a wired or wireless one?

Need help with Airport Express and so on.

Ok so my main problem before getting into what I need help with here is that our MacBooks and now my iPhone 6 plus isn't staying online. Keep getting booted off and then I either have to select the network again or it will eventually go back on. If anyone has a solution or so please feel free to answer that as well. I'm running on Roadrunner with a Netgear 600 wireless router and a motorola modem. Both of which I'll leave the link to below for a better look.
My Main Question: So I'm looking at a new wireless router mainly and possibly a new modem. I know Apple products are trustworthy but how good is the Airport Express and other Airport products. Also what is the Maximum speed and Maximum data speed for the cheapest express station and if anyone knows the speeds of the other devices it would be greatly appreciated.

DSL Router to Netgear 5-port Switch and I used the switch to connect to Airport Extreme, TV, Blue-Ray DVD player and DirecTV Receiver.
The AirPort Extreme base station (AEBS) is a router so it will do what you need.
You need to reconfigure your setup. Connect the WAN port of the AEBS to the DSL router. Then connect the Netgear switch to one of the LAN ports on the AEBS. The AEBS will properly share the connection.

I have an airport express and want to know how to set up two different wireless networks. One with 5GHZ and one with 2.4GHZ so different devices can connect to either.

I have an airport express and want to know how to set up two different wireless networks. One with 5GHZ and one with 2.4GHZ so different devices can connect to either. I have an iphone 4 that will not connect to 5ghz.
thank you!

Your AirPort Express is already providing two separate 2.4 GHz and 5 GHz bands, but each band is using the same wireless network name.
This is the default setup for the AirPort Express, which is recommended for most users. The theory here is that devices will automatically connect to the best quality signal based on their capabilities and distance in relation to the AirPort Express.
It is possible to assign a different name to the 5 GHz band, and then "point" devices at that network to connect. Some users swear by this option.....(I am not one of them).... but you might want to give it a try to see how it works for you.
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Express
Click Edit in the smaller window that appears
Click the Wireless tab at the top of the next window
Click Wireless Options near the bottom of the next window
Enter a check mark next to 5 GHz Name.....which will automatically add "5 GHz" to the network name....so you can identify it
Click Save, then click Update and wait a full minute for the Express to restart
Now you will need to "point" your 5 GHz capable devices at the 5 GHz network name. 2.4 GHz devices will connect to your "other" network name.

I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work?

I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work? And one more thing about the setup, the linksys router shich acts as a base is in a different room as the airport express which i wanted to use for airplay. So I'm hoping to hook up the Airport express via wireless signal. If i can set it up, can someone pls help me out by posting detailed instructions. Thanks so much!

The first message that AirPort Utility will display during the auto setup will be that the Express will be confgured to "extend" the network. When AirPort Utility analyzes the network further, and sees that the Express cannot "extend" the 3rd party network, the next message will indicate that the Express is being configured to "join" the wireless network.
Once the Express is configured, if you later go into AirPort Utility to check the settings under the Wireless tab, you will see that the Wireless Mode is indeed "Join a wireless network".

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network?

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network? Network is administered through an iMac running OS X Yosemite 10.10.2. Ideally, would like for the second Airport Extreme hard drive to appear on the list of devices in the Finder window.

Ok.. gottcha
The problem is network wise.. Yosemite is about equal to tin cans and string.. pathetic.
Here is my usual set of instructions to get anything working on Yosemite.
The best way to fix problems is a full factory reset of all the AE in the network.
Factory reset universal
Power off the AE.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the AE to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg AEgen5 and AEwifi for basestation and wireless respectively.
Even better if the issue is more wireless use AE24ghz and AE5ghz with fixed channels as this also seems to help stop the nonsense.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the AE always takes the same IP address.. this is not a problem for AE which is router.. it is a problem for AE which is bridged.. you will need to set static IP in the main router by dhcp reservations or use static IP in the AE which is tricky.
4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric..
5. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
6. Now mount the disk of the second AE in finder... manually.
Use Go, Connect to Server and type in the AE ip address.
SMB://10.0.1.2
Where you will replace that address with the actual address. The network resource should be discovered and then it will request the password.. type that in and make sure you tick to save it in your keychain.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
Do as much as you want of the above... not all of it is necessary.. only if you want it reliable.. or as reliable as Yosemite in its current incarnation can manage.
The most important thing is point 6.. mount the disk using direct IP address and not names.. dns in Yosemite is fatally flawed.
See http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/

Airport Express and Popcorn Hour (or other wired only ethernet device)

Similar Messages

Maybe you are looking for