Airport Express and WPA2 on Linksys E3000 Router

I'm running MS Windows Vista. I have a Linksys E3000 router and an Airport Express both with updated firmware.
I have segregated my wireless network: My Xbox is on the N-speed band by itself and everything else, including my iPhone 4, is on the g-speed band.
My wireless network works with full Internet access but I can't connect my Airport Express to it. I need help connecting my AE to my existing wireless network so I can stream iTunes music from my PC to the AE.
According to this link: http://www.apple.com/airportexpress/specs.html "When joining an existing wireless network, AirPort Express supports only WPA-Personal. WPA2 requires a Mac computer with an AirPort Extreme Card and Mac OS X v10.3 or later"
So I went to my router settings and set up my g-speed band for "WPA-Personal." But when I do that, my g-speed band ceases to work. I cannot connect my iPhone 4 to it and my iPhone has no trouble connecting when the security is set for "WPA2-Personal".
The Aiport Utility (v 5.5.1) will not detect the AE wirelessly. When I connect the AE via ethernet to the router, I can configure it with Aiport Utility and it will stream iTunes music over the wireline network but then when I disconnect it, I can't detect it wirelessly. I've tried using the setup wizard and the manual setup. I've also reset the AE to it's factory settings and started again with no luck.
I've spent hours trying different settings and I am not sure how to proceed. Please provide any feedback you may have.
Message was edited by: DroidDreamer

Most likely you entered the password a year ago when you first set up the AirPort Express (AX) and you checked the option to store the password in your keychain. If you do that, the Mac will never ask you for the password again.
Open Keychain Access and see if you have an item with the name of your wireless network.

Similar Messages

Using AirPort Express to extend my Linksys WRT160N router signal

I am currently using a Linksys WRT160n v2 Wireless Router in my home, but the signal in certain places is quite weak. Therefore, I bought an AirPort Express and was told that this could be used to boost my signal to the weak areas.
I am not sure how to accomplish this and need help!! I realize that using an AirPort Extreme Router would be easier, I just don't have the cash to purchase one right now. Is there anyone who can guide me through setting up my AirPort as a range extender for my Linksys WRT160n v2 Router?
Thank you in advance!!
Timothy Kortman

Why did you not just look into buying a Linksys Range extender instead of the Airport Ex?
There are also extenders from Hawking Tech that would have worked just fine like this one http://www.hawkingtech.com/products/productlist.php?CatID=32&FamID=105&ProdID=39 4 .
+*An aside...*+
i wished Linksys would have kept the detachable antenna design on their new routers, that way extending it's range would just be a matter of getting higher dbi antennas which are more cheaper than range expanders.
I currently have a run of the mill TrendNet router but hooked up to a high gain Hawking antenna and it outperforms most routers twice/thrice its price.

WDS setup with Airport Express and other(non-Apple) wireless router

Hi,
I am trying to configure a wireless network with one airport express and one Planex Wireless access point. Can anyone please point me to the settings to be made for such a scenario? I can use either of them as the main WDS device, and have a (wired)router provided by the ISP in the network.(so total 3 devices : airport, planex a/p , ISP router)
Thanks.

I'm having the same problem, both with a Linksys WRVS4400Nv2, and a WRT54G. I've not put much effort into the WRT, but the WRVS was such a pain that I don't think I can get it to work at all.
The WRT doesn't have a section on WDS, but I've read that it's supported anyways, and nothing needs to be enabled on it. Is there a good step-by-step available here or elsewhere that uses close to the same router and Airport Express units, on the latest Airport setup software?
Basically, I'm trying to set this up for a guy in an ~8000 sq. foot house so he has wireless throughout it, and he wants itunes streaming from the AX. Has anyone done this?
Message was edited by: manderso

Airport express using WPS to Linksys Wireless router?

I have a Linksys Wireless router set up to server wireless signal to macs and PCs in my office. It works great, but one of the far offices can't get enough signal.
I bought an airport express assuming I could use it as a repeater in this office.
I'm having some trouble connecting it (config goes great, then when i try and enable WPS mode - entering the current Linksys ID it just flashes orange after restart).
Any tips? Should this be possible?
.dave

Never found a solution to this.

Airport Express and WPA2 confused

I went into my airport express settings...I have a macbook and it is the only computer in the house that is wireless.
In my settings under the airport express admin utility:
I enter in my password to access the main utility page and under the "airport" tab at the top about 3/4 way down on the left it reads:
Wireless security: WPA2 Personal
I have never had to enter a password to go online since I put the airport express in a year ago.
I basically turn on the macbook and surf with no passwords to enter to gain wireless access on my macbook using airport express.
I am concerned that my wireless connection is not encrypted and others may be able to use the connection. Am I OK here as far as security with what I have listed as WPA2 Personal under "wireless security?"
Is th reason I do not have to enter a password everytime I go online, because I my family is the only user on the one wireless computer?
If I were to now try to go wireless with airport express using Playstation 3, do I put in my password allowing access to the settings page?
Very confused.
Thanks
Kroe

Most likely you entered the password a year ago when you first set up the AirPort Express (AX) and you checked the option to store the password in your keychain. If you do that, the Mac will never ask you for the password again.
Open Keychain Access and see if you have an item with the name of your wireless network.

Airport Express can't see Linksys router

Hi, I'm getting nowhere trying to get my Airport Express to find my Linksys E2000 router and I hope someone here can help.
The E2000 is connected to the internet and both laptops in the house, an iphone and an Android phone can all use it successfully. I have a 1 month old Airport Express which I'd like to use to stream music. Until today I've been using the Express as the wireless router without problems so I know it can be used in that capacity. In the Airport Utility, the Express is found but after setting the Wireless Mode to 'Join a wireless network', the droplist of visible networks does not include the E2000's secured network. Curiously, the unsecured guest network created by the E2000 can be seen. The network which can't be seen is secured with WPA2-PSK. I've tried disabling the firewall on the E2000 but this had no effect.
Has anyone else come across anything similar with the Linksys routers or similar? Any help will be greatly appreciated.

It won't come up up in Airport Admin Utility. To configure the router launch a browser. Typically Linksys routers use 192.168.1.1 as the admin address for their routers. Once there, use admin as the password to gain access. If it won't let you in you will need to reset the router to factory default settings. Check the Linksys web site for the router manual.

I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work?

I have a linksys WRT54G router that we use as a base. I want to use Airplay using Airport Express and hook up my stereo to it. How can i set up my Airport express without a PC/laptop? I just downloaded Airport utility on my iphone and ipad,will that work? And one more thing about the setup, the linksys router shich acts as a base is in a different room as the airport express which i wanted to use for airplay. So I'm hoping to hook up the Airport express via wireless signal. If i can set it up, can someone pls help me out by posting detailed instructions. Thanks so much!

The first message that AirPort Utility will display during the auto setup will be that the Express will be confgured to "extend" the network. When AirPort Utility analyzes the network further, and sees that the Express cannot "extend" the 3rd party network, the next message will indicate that the Express is being configured to "join" the wireless network.
Once the Express is configured, if you later go into AirPort Utility to check the settings under the Wireless tab, you will see that the Wireless Mode is indeed "Join a wireless network".

Airport Express and Linksys bridge, HELP!!!

Hello,
I was just wondering if it was possible to use a Linksys router as a primary wireless access point and using the Airport express to bridge/ extend the wireless network?
If so, what are the steps that i must take to make it happen?
Would i be able to thus use the airport express' ethernet connection cable to connect to my xbox 360, in effect, turning the Airport express into an expensive wireless ethernet adapter?
Thanks in advance...
Ian

Thanks a lot...
Just one last question though, would i be able to use the ethernet cable from the airport express and connect it to let's say, an xbox 360, will the airport express work as a wireless ethernet adapter now?

Airport Express and 3rd Party Router

I have a first generation Airport Express that I've been using for the past few years to stream music wirelessly to my stereo via my Belkin 54g router. At first I could not get the Airport Express to work with the Belkin Router but finally after posting on this discussion board, someone told me how to make it work.
Well, I finally decided to buy a new router with the N-protocol (Linksys E2000) and I cannot get it to recognize the Airport Express at all, even when I hook it up via ethernet cable. I cannot remember the steps I went through to get the Belkin router to work with the Airport Express. I hope someone can help me so I can get it working again.
Thanks,
Mark Brandenburg

Mark,
You need to "hard reset" the AirPort Express by holding in the reset button until the amber light begins to blink more quickly, hold another 3-4 seconds when you see this, then release the reset button.
Open AirPort Utility to reconfigure your AirPort Express to "Join" your Linksys wireless network. The AirPort Express should "see" the name of the Linksys network during the configuration, but the hard part is knowing exactly what type of wireless security that your Linksys router is using.
You must enter a matching setting on the AirPort Express to get it to "join" the network correctly, so you may need to check the settings on your Linksys router first if you are not sure of the exact security setting that it is using.
The other thing you need to check is to make sure that the Linksys is broadcasting a compatible signal so your older "g" AirPort Express will be able to join the network. If the Linksys produces an "n only" wireless network, the AirPort Express will not be able to join the network since it is a "g" device.

Airport Express and Fios Actiontec router compatible?

I have multiple Airport Expresses and an Airport Extreme. Verion FIOS supplied it own Actiontec router which hooks into their Optical Network Terminal. Since the Actiontec router took over, I've removed the Airport Extreme and the Airport Expresses work only to receive iTunes music from my computers. The Expresses do not extend the WiFi signal anymore. The Actontec router is powerful but at the far end of the house, I no longer get a WiFi signal. Previously with my Extreme and Expresses, I could extend the signal wherever I needed it.
I wonder if I can plug my Extreme into a hardwired LAN terminal from the router and use it to create its own WiFi network in the areas of the house where there is no signal?

I wonder if I can plug my Extreme into a hardwired LAN terminal from the router and use it to create its own WiFi network in the areas of the house where there is no signal?
Yes, this is possible if the AirPort Extreme stays permanently connected using an Ethernet cable.
If you want to create one "big" network, use the same wireless network name and password on the AirPort Extreme that you use on the Actiontec router. Setup the AirPort Extreme to "create a wireless network". The Extreme must be in Bridge Mode to do this.
If you configure the AirPort Extreme with a different wireless network name, then you will need to log on to that network separately each time that you move your computer close to the AirPort Extreme.....then log back on again to the Actiontec when the computer moves back near that router.
If the AirPort Express devices are located where they can receive a good wireless signal from the AirPort Extreme....and you need even more wireless coverage.....,the Expresses could be reconfigured to "extend" the wireless signal from the AirPort Extreme like you were doing before.

AirMac Extreme and Airport Express not working with Netgear N Router?

I've been using an AirMac Extreme (old model) as a wireless router, and Airport Express for it's airtunes functionality (conected to my Hi-Fi).
These used to work fine, and both would show up in my Airport Utility on my Macs.
I've now just upgraded to a 50MG broadband contract, and the engineer gave me a Network router as my old AirMac Extreme couldn't handle that bandwidth.
When I connected my AirMac Extreme to my Netgear router I then got conflicts, sometimes it wouldn't show up, and it really slowed down my wireless signal. As a result the contractor for my broadband recommended I disconnect my Air Mac Extreme from the router. Speeds went up for the internet, but now I can't get my airtunes to work.
What I want to know is can I just use my Netgear to transmit the broadband signal so I get maximum internet speeds, but then have my AirMac Extreme and Airport Express connected so that I can still listen to my itunes wirelessly?
Ideally I'd like this to all be set up so that I could be conected to the internet through the Netgear wirelessly and listen to my itunes through the Airport Express at the same time.
Thanks in advance for any advice.

I am sorry that I don't have a definitive answer but I also have Windows computers and I have "inherited" some older Apple devices from my son and am trying to learn about them so in addition to searching this group, I "Googled" "1st generation airport express" and it listed many specific posts in this group - I read them all and they might answer your question - good luck

I have the airport express as router can I buy the new airport express and use my old airport to extend my net?

I have the airport express as router can I buy the new airport express and extend my net?

Things can get confusing pretty quickly since there are 3 different versions of the AirPort Express.
If by "old", you mean you have Model No A1084 or A1088 AirPort Express (look at the label on the side of the device for the Model No), it cannot be used with the "Extend a wireless network" feature of other newer Apple routers.
If your AirPort Extreme is "square" shaped with rounded corners, then the "old" AirPort Express will not work with your AirPort Extreme using the "Extend a wireless network" settings.
You could use a "previous version" AirPort Express, Model No A1264 to "Extend", or the "new" AirPort Express, Model No A1392, for that purpose.
If your AirPort Extreme is a simultaneous dual band product, then the "new" Express would be able to "extend" both bands. The "previous" AirPort Express (Model A1264) would be able to extend only one band, since it is not a dual band device.

Airport Express and D-link router

I have a new Airport Express and a D-link DI-524 wireless router which I wish to use to both extend my wireless network and connect my Xbox 360 wirelessly as it is not near my base station and I don't want to wire through my house.
Could anyone please give tips on how I should do this? Should I use the Airport as the base station or the router? How can I get my Xbox to see the internet?
Your help will be muchly appreciated!

danbowles, Welcome to the discussion area!
Sorry but that is not possible. The Ethernet port on the AirPort Express (AX) is ONLY activated if it is connected wirelessly using WDS. The D-Link router does not support Apple's WDS.

Is is possible to use a netgear wireless router to share a cable internet connection between an airport express and a Sony BD player?

Hi,
I have a couple of netgear wireless routers (WGR614, WPN824 v3) as well as a Belkin wireless router (F5D8233-4v3) lying around, and was wondering if it is possible to use any of these to share the internet feed from a cable modem to both an airport express and a Sony Blu-Ray Player? I connected the WPN824 router between the cable modem and the airport express but the airport express will only give an orange light then as if it does not have internet access. Any suggestions would be much appreciated! Many thanks.

What you are basically attempting to do is extend the Belkin router with the AirPort Express Base Station (AX) via a wireless connection between them. This method is known as a Wireless Distribution System (WDS). Unfortunately, WDS is not a standard and router manufacturers implemented, in most part, to only work with their products ... so it will be very unlikely that you can create a WDS between your Belkin and the AX. There have been a few Belkin model that have been updated by third-party firmware that support WDS, but the models you listed are not any of them.

HT4437 can i have more than one apple tv at different locations by ethernet on the same router thinking of dumping the airport express and hard wiring an apple tv if this is possible

can two apple tv's be used on the same network and router they would be in different locations one inside the house and one for an outside system? may dump the airport express and go to ethernet wired direct to each apple tv from same router..

Welcome to the Apple Community da dad.
Yes you can connect multiple Apple TV's by ethernet.
What do you mean by outside.

Airport Express and WPA2 on Linksys E3000 Router

Similar Messages

Maybe you are looking for