Airport express base station has disappeared from airport admin utility

I think I have the same problem as several others here.
Network with extreme and express has been working fine for month. Express is used to connect and share usb printer. Yesterday it decided to disappear. Have reset both extreme and express. Extreme is back online so I have web access, but express does not show up so I can't configure it and run my printer.
Any help is most gratefully appreciated!

It's not difficult to set up an AirPort station as an extension for the Time Capsule. Apple gives you the steps to follow > http://support.apple.com/kb/HT4145?viewlocale=en_US&locale=en_US

Similar Messages

Had a Airport Express connected to my stereo and it was working. I brought an Airport Extreme and suddenly it took over and Airport Express stopped working and disappeared from Airport Utility. What I am supposed to do? ar2ro

I have an Airport Express connected to my stereo and it was working without any problem.
Recently I bought an Airport Extreme to use it as my Base Unit connecting it to my DSL.
I followed the instructions of the Airport Utility, and it started working.
Suddenly, problems started happen the Airport express that was connected to the stereo , stopped working and it disappeared from the Airport Utility area , as it did not exist in the network. I tried to reset it but it did not appear in the Airport Utility page.
Apparently I have other problems with the private network that it created because I cannot use it because of problems with the password that was created. I can only use the network that I created for my guest...
I dont know if my problem is a configuration problem or there is problem with the equipment.
I read that other users where having the same problem with the Airport express , using non apple equipment as their base unit , but I thought that using the Airport Extreme was going to be compatible and no problems would happen.
What should I do?

Common Problem. Common solution.
Connect your Express via ethernet cable to the Mac while other network connections on the Mac are switched OFF.
After the Express shows up, change the settings of the Express to join the existing network. Take the appr. settings.
Unplug and reconnect your Mac to the network.
Check if the Express shows up in Airport Utility
Alternative solution:
Hardreset the Express to factory settings
(while on power push the Pin next to the audio plug with a paperclip. Plug out the Express still holding down the little button then replug the Express to power and release button)
After that, the Express will show up in the Airport Utility.
Make all needed settings.
I would prefer the first solution, its easier just to plug a cat5 cable.

After downloading firmware for airport utility, airport express base station no longer registers with airport utility on my Mac. Now the base station is blinking amber with no info of what is causing all this to happen. Any suggestions?

After downloading firmware for airport utility last night, airport express base station was deleted from airport utility and only Time Capsule remains. When I plug in the base station, an amber light blinks without being able to verify the cause. Any suggestions to remedy this problem?

There are only a couple of things you can do to resuscitate a nonresponsive Express:
"Hard reset":
Press and hold the reset button with a pen or pencil until you see the status light (LED) start to flash amber rapidly, which should occur after about five seconds.
If that does not work,
"Factory defaults reset":
Unplug the Express from power.
Press and hold the reset button with a pen or pencil, then plug the Express back in while continuing to hold the button until you see the light (LED) flash rapidly. This should happen after a few seconds.
Release the button.
In either case you will have to reconfigure the Express as a new device. A moment or two after it has been reset, the LED should be blinking slowly. It must then appear in your Wi-Fi menu like this:
Earlier versions of OS X will report it as "Apple Network nnnnnn".
In either case, select it, and then launch AirPort Utility.
If it does no appear in your Wi-Fi menu after it has been reset using one of the two techniques above, it is defective. Other than attempting another reset, there is nothing you can do.

Streaming from Denon receiver to Airport Express Base Station?

Hello,
i know it's possible to strem music, video, etc. from your apple device to a Denon receiver with airplay, but is it also possible, to stream sound from the Denon receiver to an Airport Express Base Station? I'm about to purchase such a Denon receiver and 2 Airport Express Base Station. To the Airport Express Base Station's i want to connect speakers, the Denon receiver will be connected to the TV and Bluray. So i was wondering, if i could stream the sound from the TV / Bluray, via the Denon receiver to the Airport Express Base Stations. Or is the airplay function of the Denon a one-way road?
Thanks for feedback!
Jay

Jayelkay wrote:
is the airplay function of the Denon a one-way road?
yes.

AirPort Express Base Station and USB Webcam

I see that the AirPort Express Base Station has a USB port. Is it possible to connect an off the shelf USB webcam, maybe from Microsoft or Logitech, to the AirPort Express Base Station USB port and use it as a wireless surveillance system? Of course you would need proper monitoring software. You could have an AirPort Extreme Base Station connected to your network and several AirPort Express Base Stations with USB webcams attached keeping track of say your home, your business, etc... If you had the correct monitoring software, you could view any motion triggers from let's say your iPhone. The monitoring software would work with both Mac and Windows. Great idea right? Is this idea even feasible? If so, how? If not, why not? I'm just trying to figure out a way using standard off the shelf USB webcams. Any suggestions would be helpful and I thank you in advance.

Well your best bet would be to get a wireless webcam! Cisco makes a great one as well as D-Link! Here are a few models:
D-Link DCS-1000W 802.11b Wireless Webcam
D-Link DCS-930L Wireless N Network Camera
Cisco-Linksys Wireless-N Internet Home Monitoring Camera
Good Luck! -Josh Jones

Airport express base station question

Since the airport express base station has a dial-up modem v.90 port, does that mean I can connect to dial-up wirelessly? I am getting a powerbook g4 soon, and I am one of the few left that cannot get highspeed in my area, and I want to be able to search the web throughout my house, on my soon to have powerbook. This would be the only reason I would buy this product, so will it work?

So if i get the airbort extreme base station i can
connect to dial-up wirelessly? How much of a loss of
speed?
None as the wireless speed is much much faster than your dial-up speed.
Wireless connection 54000 Kbps
Dialup connection 56Kbps
iFelix

I want to re-use my old airport express base station but airport utility doesn't recognise it anymore (it dates from 2005) i would like to use it to connect to my speakers only

I have an old airport express base station from 2005
I would like to have a network on it so i can put it upstairs in a room and connect my speakers to it so i can send my music (from itunes) over the airport to my speakers.
I reset it and now i want to configure but the Airport utility doesn't recognise it anymore.
Can i update the firmware? has it become useless because too old or what can i do?
I work on macbook pro with macOSX 10.9.4
Can someone give me some tips please
thanks
J

Please locate the model number on the side of the AirPort Express. Hard to see.....gray lettering on a white background....so you may likely need a magnifying glass and good lighting to see it.
The model number starts with a "A" followed by four numbers. If you see A1084 or A1088, unfortunately AirPort Utility 6.x in Mavericks OS X (10.9.4) does not support these older models. However, you can still administer these models if you have a Mac.....or can borrow one for a few minutes....using Leopard (10.5.x) or Snow Leopard (10.6.x), or a PC with AirPort Utility installed on the device.

Airport express base station too old?

I keep intermittently losing my wifi connection with my Macbook Pro. However, my iPhone and my iPad have no problems jumping on the wifi connection.
I have an XBridgeDSL ethernet router modem which is paired with an Airport Express base station and both of them are about 13 or 14 years old. I installed Mavericks when it came out, everything seemed fine, but am wondering if it was a step too far for my poor old kit.
I can get wired connection with the computer no problem, and right now I've managed to get Wi-fi - but it randomly disappears, and the network doesn't show up in the list of available networks.
I've just run Airport Utility and it finally showing my base station, but says it doesn't support it.
Am I having these problems because my base station is too old now?
I don't really want to incurr any unnecessary expense of buying new kit if I don't need to...
At the moment I have to switch between wired and wifi depending on which device I want to use which isn't great.
Any further advice or tips would be great.
Best
Heather

Hi,
Yes, that's exactly the same message I got with my base station (but in English). This has worked for me:
-Disconnect from wifi
-Moved computer very close to the router
-Place ethernet cable from router modem to computer, connect to internet wired.
-Left it for a few hours, then put the ethernet cable back into the airport express
-After about 20 mins I went back to the computer and noticed it was connected to wifi again
-Haven't turned it off since so OK so far
-Found a new internet supplier who will supplier a wireless router modem free of charge and signed up. I just have to hang on till 11th Jan!
Slightly unorthodox perhaps, but it's worked
Good luck with yours, my feeling is that my Apple base station is now too old and no longer supported. Also I suspect I'll get better internet download speeds with the new router modem, currently only getting 4000mbs compared to a possible 120,000mbs in our area, and my upload speed is about 0.4mbs.
H

I have two airport express base stations that I want to configure on two separate sets of speakers in two separate rooms. How do I do this? Airport Utility only seems to scan one express at a time.

I am currently running a PowerPC G5 imac and have a wired broadband modem via ethernet with airport wireless network turned on, on the G5. I have the computer in the bedroom and have an airport express wired into a mixer that connects to my stereo. I have recently bought another airport express base station to connect to a pair of active monitors in the kitchen. When I try to scan these on Airport Utility version 5.42 I am only managing to scan one base unit at a time. I have plugged them in separately and reset them, they both have firmware updates, however the utility will only read one at once. I have read that you can link base stations to the same WDS. I would like to know how to go about doing this if it will only scan one airport express at a time. I have looked it up on the net and not found anything that is a simple fix. Can anyone help? In Apple Support it says that multiple Base Stations can be used. I would like to get both Apple Airport Express units to be able play airtunes separately or at the same time depending where I am in my flat. I do not need different music in each room. I would like to stream music from the computer to multiple rooms in the flat without having to continually unplug and configure the Base Stations. Has anyone come across such a challenge? Any help would be welcome.

How do I configure the AX to connect to the hub's wireless network? It will only scan one base station Airport Express at a time in the Airport Utility. I think what I am trying to do is use the hub as a router to the two AX's. Is there a specific way to set this up?
To set up the AX to join a wireless network as a "Wireless Client," using the AirPort Utility, either connect to the AX's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, try these settings:
Launch the AirPort Utility.
Select the AX.
If not already connected to the AX's wireless network, go ahead and switch to it when prompted.
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <type in the network name/SSID of the wireless network that you want to join or select it from the pop-up menu>
Wireless Security: None OR, if you are using security on your wireless network:
Wireless Security: <Select the appropriate level of security for the existing wireless network: WPA/WPA2 Personal | WPA2 Personal>
Password: <enter your wireless network security password>
Verify Password: <re-enter the same security password>
Click Update to write the new settings to the AX.

Can you add new AirPort Express Base Station Simultaneous dual-band 802.11n with a 1st Gen time capsule network

Hi
Has anyone tried using the AirPort Express Base Station with a first generation Time Capsule and used it to extend their network, while still being able to use the Simultaneous dual-band 802.11n on their network?
Thanks in advance

The first generation Time Capsule was not a simultaneous dual band device.
If you add the "new" AirPort Express to the network and configure it to "Extend a wireless network", it will extend the one single band signal that it is receiving from the Time Capsule.
In other words, the AirPort Express will not extend simultaneous dual bands in this type of setup...since it can only "extend" what it receives. You would need a simultaneous dual band Time Capsule if you want that type of functionality.

Airport Utility can no longer see my Airport Express Base Station.

Hi all the problem I have is as follows;
I've set up my Airport Express Base Station some time ago to print wirelessly from my HP Photosmart C4280 and it was working fine.
However recently when I've gone to print a document, even though the printer is working fine and the Airport Express Base Station is showing a green light nothing happens. I've gone into the Airport Utility and its say's it can't see the Airport Express Base Station (even though it still has a green light showing). If I unplug the Airport Express and plug it in again, the Airport Utility can suddenly see it again.
I've successfully gone through the reset process but after a few minutes the Airport Utility can no longer see the Airport Express Base Station which means I can't print a document wirelessly. I've repeated the reset process several times with the same outcome.
Everything was working fine up until recently, has the Airport Express Base Station developed a fault? or is there something I'm not doing.
Any advice would be greatly appreciated.

If you're comfortable resetting all settings, unplug it, hold down the reset button and keep holding it in as you plug it back in - keep holding it for another 10-20s until the amber light flashes
Then, open airport utility, now you should be able to see the device either on-screen or in the upper left under 'other wi-fi devices'

I want to set up my Airport Express Base Station again but do not remember how. Please walk me thru it.

I am trying to hook my Airport Express Base Station up to be a router again and have forgotten how to do this. Before I had it hooked through the modeum and would like to have it that way again but for some reason the process has completely left my memory. I know it has something to do with the little icon on the top of the computer but not what it has to do with it. Because it is not hooked up I am unable to get my printer to work unless I connect to another wireless that I have but do not want to use all of the time since I have to pay for it and do not have many GB. I am also paying for another that I want to use all of the time (unless necessary to use the other) so It only cost me when I am away from home. Please walk me through the process of hooking the Apple router back up.

All apple routers are setup via Airport Utility.. there is no icon for it in the top menu area.. I think you are confusing the airport network setup (ie the internal wireless card in the Mac) with the airport express setup.. Apple insist on calling everything the same name which makes it more confusing.
Open the airport utility which you find under applications/utilties.
Router setting will depend on what version of the utility you are using.
In version 5 it is under Internet tab and in v6 utility under network. You need to set it to DHCP + NAT.
Download and read the manual for setting up the express if you have forgotten the details.. manuals are always good.. all the manuals are listed at the head of the section. But you are in Time Capsule instead of extreme/express specific area.
https://discussions.apple.com/community/wireless/airport
Manuals link http://support.apple.com/manuals/%23airport
If you want the express as router the modem should be bridged or it should be a pure modem for it to work without Double NAT issues. There is nothing wrong with bridging the Express.. that is not the same as using it in wireless bridge modes.. that is router bridge.
What modem do you have?
I am at a loss to understand the rest.. why the printer is not part of your own network.. and how setting up the airport this way is important. You need to give us specific details if you need more help.
How exactly is the airport setup now?
How do you connect to the modem?
How is the printer connected? What kind of printer?

Why won't the Airport Utility recognize my Airport Express Base Station

I have an Airport Express Base Station I had recieved from a friend of mine. It is a 802.11n Wi-Fi Station, and I'm running OSX 10.7.4. When I open airport utility 6.0 it can't find my devie and the same with Airport Utility 5.6. I've tried resetting the station and plugging it directly into the computer via ethernet cable but nothing has happened. Someone help?!

Nevermind, I figured this one out. Just perform a hard reset. Unplug the base station, push and hold the reset button then plug the station back in while still holding the button in. Continue holding till the the LED flashes yellow really fast. Release and wait till the Airport Express starts up.

Why have all 3 airport express base stations stopped working, BT have checked and improved line still not working?

Why have all 3 airport express base stations stopped working, other users are on ipads and BT have checked and improved line but I still have an intermittent/no connection?

You must tell us the whole setup.. what is the main router?? How are the express connected to each other?
On ipad it works ok?? But you are on a computer?? MBP early 2011 running Lion?? That doesn't work.. even if you are right next to the main router??
Plugged in by ethernet does it work??
Have you installed a wireless diagnostic program.. ?? Actually Lion has one installed but hidden I believe.
Later version bought it to the surface.
About Wireless Diagnostics
If you do run Lion please install the 5.6 airport utility as it will give you loads more info on how the units are connected.. and link speeds for extend wireless.
How to load 5.6 into later Lion & ML
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
Leave the package open on the desktop so you can see the file. AirportUtility56.pkg
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. If your Mac refuses to run the software, because it wasn’t downloaded from the Apple store, go to security in preferences and allow other software to work.. this is limitation of trade methinks. You can set back later if you like.
Now drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. in finder, open the new directory, drill down.. applications, utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall version 6 (now 6.3 if you updated) so don't try.. and you cannot or should not run them both at the same time.. although I have had no problems when doing so.

Apple AirPort Express Base Station with 802.11n - MB321LL/A. How to set it up to my new iMac

Community:
How do you set up an
Apple AirPort Express Base Station with 802.11n - MB321LL/A how do you set up on Mac running on OS X 10.9.4?
Please advise
Fmsalazar

Apple did say it was important.
If the units do not show up in the airport utility then you must set it correctly to link-local.
Steps for OS X Lion or Mountain Lion
This can happen if IPv6 has been disabled. To enable IPv6 for your network interface:
Choose Apple menu () > System Preferences, and then click Network.
If a lock icon appears in the lower-left corner, click it and enter your admin name and password to unlock the pane.
Click your network service (Wi-Fi or Ethernet) in the list, and then click Advanced.
Click the TCP/IP tab.
Choose Link-local only from the Configure IPv6 pop-up menu.
Click OK.
Click Apply.
AirPort base station not seen or "An unexpected error occurred" appears in AirPort Utility 6.3
Apple rep says the same.
Re: Unexpected error when connecting Airport Express A1264 to Airport Utility 6.3.1
I am searching as I saw it in a thread today where a person had issues. (No contribution from me in the thread but found that was the issue).
It is kind of a fail safe.. since auto can end up with any setting.. and it will depend on the setting of ipv6 in the Airport Router if it works properly in the computer.. setting it to the correct value is one step in sorting out problems when people get in a mess.

Airport express base station has disappeared from airport admin utility

Similar Messages

Maybe you are looking for