AirPort Express Base Station sticks out too far (Solution)

Hi all,
I don't know if this comes up very often in this forum but a problem with having the Airport Express Base Station plug directly into the wall is that it sticks out too far, IMO.
I have one hooked up in my bedroom so I can play music over a BOSE Wave Radio. I have two possible power outlets to plug it into. One is next to the bed. There is about 18 inch gap between the bed and the wall. I don't want the device there because I may bump into it while making up the bed. The other place is behind the dresser. However, this spot would make me have to pull out the dresser a little too far from the wall than I would like. Behind the dresser is preferred because it is the closest outlet to the radio.
Solution: I went to a local hardware store and found a six socket mini power strip that plugs directly into the wall. Here in the US, our power outlets have two sockets lined up vertically. This device plugs into both sockets. The top plug has all three prongs. The bottom one only has one ground prong. Each side has three 3-hole sockets. The sockets on one side are upside down.
With this mini power strip, I can plug the Airport Express Base Station into the side of the strip such that the side of the base station is almost against the wall. Now, I can have my dresser very close to the wall. There is a very small gap between the base station and the wall and dresser to allow it to breathe.
I also plan on using more of the these mini power strips behind other pieces of furniture so that the furniture no longer pushes against power cords sticking out of other outlets. The one downside is that this mini power strip won't handle wide transformer based adapters.
I hope this tip helps others.
Enjoy life!
Steven

See the original message.

Similar Messages

  • Airport express base station too old?

    I keep intermittently losing my wifi connection with my Macbook Pro. However, my iPhone and my iPad have no problems jumping on the wifi connection.
    I have an XBridgeDSL ethernet router modem which is paired with an Airport Express base station and both of them are about 13 or 14 years old. I installed Mavericks when it came out, everything seemed fine, but am wondering if it was a step too far for my poor old kit.
    I can get wired connection with the computer no problem, and right now I've managed to get Wi-fi - but it randomly disappears, and the network doesn't show up in the list of available networks.
    I've just run Airport Utility and it finally showing my base station, but says it doesn't support it.
    Am I having these problems because my base station is too old now?
    I don't really want to incurr any unnecessary expense of buying new kit if I don't need to...
    At the moment I have to switch between wired and wifi depending on which device I want to use which isn't great.
    Any further advice or tips would be great.
    Best
    Heather

    Hi,
    Yes, that's exactly the same message I got with my base station (but in English). This has worked for me:
    -Disconnect from wifi
    -Moved computer very close to the router
    -Place ethernet cable from router modem to computer, connect to internet wired.
    -Left it for a few hours, then put the ethernet cable back into the airport express
    -After about 20 mins I went back to the computer and noticed it was connected to wifi again
    -Haven't turned it off since so OK so far
    -Found a new internet supplier who will supplier a wireless router modem free of charge and signed up. I just have to hang on till 11th Jan!
    Slightly unorthodox perhaps, but it's worked
    Good luck with yours, my feeling is that my Apple base station is now too old and no longer supported. Also I suspect I'll get better internet download speeds with the new router modem, currently only getting 4000mbs compared to a possible 120,000mbs in our area, and my upload speed is about 0.4mbs.
    H

  • Getting the Most Out of My Airport Express Base Station, Part# MB321LLA

    I'm assigned in northern Europe and have recently ordered an Airport Express Base Station through the APO (US Military Postal Service). It hasn't arrived yet and I decided to read up on it's positives and negatives. I currently have an Apple iMac 27" and a HP PC on my wireless network at home. I recently purchased an iPad2 and enjoy using it over my wireless network while sitting in the living room in the evenings. Unfortunately, the wireless signal alternates between 1 and 2 bars (sometimes even 0 bars) causing considerable delay in downloading and surfing the web on my new iPad2. I recently purchased a new LED Samsung "Smart System" HD TV and plan on setting it up in the living room this next weekend (replacing a very old TV). Part of my plan was to order (which I have along with the Airport Express) Apple TV and hook it up to the new HD TV at the same time. I was concerned about the wireless signal strength, due to the non-Apple wireless router being on the far end of my home, so I ordered the Airport Express hoping it would do the job of boosting the range and also helping increase the wireless signal strength for both my Apple TV (which is still on order) and my newly purchased iPad2.
    The question is this: What is the best way for me to set up the Airport Express to optimize the wireless network (and my investment). As previously mentioned, the primary non-Apple wireless router is at least 50 ft away and is on the far end of the house (going through several thick walls in the process) from my living room area where the new HD TV is to be installed. Is it best to just add the Airport Express to the existing router via an Ethernet connection and emulate the existing wireless network, or is it best to actually set it up in the living room at the other end of the house?
    I wish I had read the comments in this forum prior to having ordered this new Airport Express device.
    Thanks...
    Cheyenne22

    What is the best way for me to set up the Airport Express to optimize the wireless network (and my investment).
    The "best" way to connect network devices is always using a wired Ethernet connection if possible. Bandwidth is much higher, and you don't have to worry about wireless interference from other electronic sources in the area or obstructions in the signal path that reduce the signal strength quickly.
    The AirPort Express can "extend" or "repeat" a wireless signal (using a wireless connection only) from another AirPort router, such as an AirPort Extreme, Time Capsule, or another AirPort Express. But, unfortunately it will not perform this service with devices from other manufacturers.
    So, you will have to go the Ethernet connection option for your network.
    If you configure the AirPort Express to "create a wireless network" using the exact same wireless network name, same type of security setting, and same password as your main router, it will provide more wireless coverage in the area where it is located.
    The AirPort Express will need to be in "bridge mode" to do this. AirPort Utility, the application used to set up the AirPort Express will walk you through the installation and select the bridge mode option for you.
    You can use the USB port on the AirPort Express to connect a compatible printer. If you want to stream AirTunes to the Express, you will be able to do that as well.

  • Airport Express Base Station and HP Laserjet 1020 printer connected

    Dear all,
    I have a Laptop (PC) Sony Vaio PCG-Z1XSP and an Airport Express Base Station which work perfectly together (internet access and I-tunes). I recently bought a printer HP Laserjet 1020 and connected it to the Airport Express USB soket. I managed to make it work and print a couple of times, but as soon as I turn off the printer or the computer or Airport Express, the next time I want to print, it doesn't work anymore.
    The Airport Admin Utility recognises the printer (I can see it listed). I have updated the Airport Express software to the Firmware version 6.3 as well as downloaded the latest driver available on HP's website for my printer. I've also substituted the USB cable. Can anybody help me here? Thank you very much and best regards.

    Hallo everybody,
    Thanks for all the answers. I have contacted HP's chat online and gone through the problem with 3 different technicians. I've tried a lot myself too. The issue was partially solved by restarting the printer spooler, i.e. stop, then start and then restart it.
    However after I was so happy that the printer worked, I turn off everything. When I turn on again, it was not working anymore. Then I tried to see by exclusion what the problem is, I had to restart the Hardwar I don't know how many times.
    Conclusion:
    1. The USB cable must be plugged into the airport express before turning on anything.
    2. Turn on the printer first.
    3. Turn on the airport express and the computer.
    4. If you try to print it doesn't work, even if you reset the airport express through the airport express utility software. The printer is recognized and appears in it though.
    5. Disconnect the USB cable from the airport express and connect it to the PC directly.
    6. Print a document.
    7. Disconnect the cable and reconnect it to the airport express.
    8. Now you should be able to print wireless. You may need to reset the airport expresst with the utility softwar, but I managed to print without having to do it.
    9. The pörinter works even if you turn off and on again the computer, or you suspend the windows session and restart it, or if you put it in standby and restart it.
    10. The printer works even if you turn off the airport express and the computer, or the airport express alone and restart them/it.
    11. The printer doens't work anymore if you turn it off and onn again. In such a case you have to plug in/out as discribeb above.
    Solution: Leave the printer always on, or make the plug in/out every morning when you start the computer and print one page direclty before being able to print wireless.
    Does anybody have a solution to this problem? I mean it prints, but it is annoying to plug in/out every day, no?
    HP's technician says that it is not a recommanded solution the HP Laserjet 1020 with the airport express, since the printer works on a host based server basis... I mean it is easy to say that, but one expects to buy a printer that works always and not to have to plug in/out everyday, restart spooler and so on.
    Can anybody comment or suggest anything I can do to avoid this? Thank you and I hope this helps others too.

  • Airtunes with Airport Express Base Station stopped working for no reason

    Hello,
    I used to play music through AirTunes with no problem. I have an Airport Express Base Station and I'm connected to it with an Airport Extreme Card built-in my iBook G4. When I came home after day at work (with the iBook, which is connected in there to wireless access point but not Apple), Airtunes is not working. Also I can not see my (not closed network) Base Station in Airport Admin Utility, internet connection is still working fine. If I connect to the Base Station by pressing button Other, manually type IP of Base Station I can connect to it and administrate it. Airtunes is allowed there, in iTunes too but it is just not working, I don't know about anything that could has been changed. I think nothing has. AppleTalk is runnig only on Airport card. Thank anyone for any advice. I tried to update firmware in the Base Station today and no software update is available.
    I created log /var/log/all.log (.), when I reconnect to the network I can see this there:
    May 31 17:37:07 jz-iBook kernel[0]: AirPort: Link DOWN (Client disAssoc 0)
    May 31 17:37:02 jz-iBook configd[59]: AppleTalk shutdown
    May 31 17:37:02 jz-iBook configd[59]: AppleTalk shutdown complete
    May 31 17:37:02 jz-iBook launchd: Server 0 in bootstrap 1103 uid 0: "/usr/sbin/lookupd"[248]: exited abnormally: Hangup
    May 31 17:37:02 jz-iBook configd[59]: posting notification com.apple.system.config.network_change
    May 31 17:37:02 jz-iBook configd[59]: hostname (multicast DNS) = jz-iBook
    May 31 17:37:04 jz-iBook lookupd[352]: lookupd (version 369.5) starting - Wed May 31 17:37:04 2006
    May 31 17:37:08 jz-iBook kernel[0]: AirPort: Link Active: "www.net23.cz/ziizii" - 0014516f4efd - chan 1
    May 31 17:37:08 jz-iBook configd[59]: AppleTalk startup
    May 31 17:37:11 jz-iBook launchd: Server 4e3f in bootstrap 1103 uid 0: "/usr/sbin/lookupd"[352]: exited abnormally: Hangup
    May 31 17:37:11 jz-iBook configd[59]: posting notification com.apple.system.config.network_change
    May 31 17:37:11 jz-iBook lookupd[354]: lookupd (version 369.5) starting - Wed May 31 17:37:11 2006
    May 31 17:37:14 jz-iBook configd[59]: AppleTalk startup complete
    May 31 17:37:26 jz-iBook configd[59]: hostname (multicast DNS) = jz-iBook
    iBook G4 12"   Mac OS X (10.4.6)  

    Please perform a "factory default" reset on your AirPort Express. Note you may need to do this a few times to make sure it "sticks." Once completed successfully, the status light should flash amber NOT green.
    This type of reset will reconfigure the Express to its factory settings. That is, it will broadcast an unsecured Wi-Fi network with a network name (aka SSID) of something like: Apple Network NNNNNN
    Can your Win7 computer find and connect to this network now? If it can, then do so and the AirPort Utility on the PC should now be able to find the Express.

  • Can I use an Airport Express Base Station to extend non-Apple router range?

    We have a Netgear 802.11n router in our house. I just bought a MacBook Pro and now am accessing out wifi from the other end of the house along with my iPod Touch 4g. Both seem to show at best about half strength signal strength. House is small and nearly all devices on same floor.
    Can I use the Apple Airport Express Base Station as a bridge to extend our wifi network giving me stronger signal for my Apple devices or will it only work with Apple routers? Netgear and others like Hawking make wifi range extenders and those are still under consideration.

    It would be extremely unlikely that an AirPort Express would "extend" the wireless network produced by the Netgear router using wireless only. Apple's "extend" feature appears to be proprietary among Apple "n" routers. As far as we know, it does not work with any other manufacturer's products for the purpose of wireless only extension.
    If you are planning to connect the AirPort Express to the Netgear using an ethernet connection, then it could be configured to extend that way.

  • Airport Express Base Station: DHCP and fixed IP?

    I have some questions about the Airport Express Base Station.
    Is it capable of providing fixed assigned IP addresses to certain specified clients, and simultaneously providing other clients with IP addresses using DHCP?
    This would be in the context of also using MAC address control -- providing services only to clients whose MAC address is in specified list.
    And finally, can it be set to not broadcast its ssid?
    Thanks!

    Thanks. This is one of those situations where my language needs to be clearer...
    The question is, can the methods be mixed. Some clients manually assigned, and at the same time others configured with dynamic addresses via DHCP. I had another wireless router at one time that was either/or -- all one or all the other, but not mixed.
    But as Doug pointed out, the Airport Express discussion group is a better place for this question, so I'll head over there.
    FWIW, this question arose when I was using Retrospect Express to back up a wireless client. Retrospect was too dumb to find the client by hostname -- or I was too dumb to figure out how to get it to do it that way -- the only way I could Retrospect to find the machine was by IP address, which meant I needed a static address. Otherwise I'd have to go in and edit the Retrospect configuration every time the client changed IP, and even that wasn't easy.

  • Airport Express Base Station no longer detectable by my computer

    Ever since I went wireless last year, I have had a love-hate relationship with my Airport Express Base Station. It seems to take forever and a day to configure the sucker, then, somehow I do and it works well for several months - until something happens to muck up the works. That thing seems to have happened this morning when Earthlink's DSL connection got wonky (it was a glitch that apparently covered a large part of the country). That glitch apparently worked itself out, but after I put my MacBook to sleep in order to get lunch, suddenly my PPPoE host went missing when I woke the machine up. Further examination indicated that, although my wireless network was still there, the MacBook could no longer find my Base Station, even though the light was still working. Resetting the Base Station does not help. I am at my wit's end here. I can work via Ethernet DSL line, but I have become used to wireless, and without a viable network, my Mac mini can't connect to the Internet. Help!

    Could you post what you did in order to resolve the issue. I'm having a problem with the base station in that I cannot connect to the internet with my laptops (a mac and pc) while I can connect wirelessly to my network with my desktop (G4). The base station is not detected in the base statin admin utility or the aiport setup utility. If anyone else has a solution I would be much obliged to read it.
    Thanks!

  • Where can I purchase a replacement CD for the Airport Express Base station A1264?

    Where can I purchase a replacement CD for the Airport Express Base station A1264?
    I'd like to sell my Airport Base Station, but I believe I need a CD with the software on it for the new owner. Anyone know where I can find one?
    Thanks!
    Meredith

    I doubt it is available.. and since a new Mac doesn't even have an optical drive.. there is no need whatsoever today for the cd.. it is all available in the OS or download. In fact the stuff on the cd will now be totally out of date.

  • Why won't the Airport Utility recognize my Airport Express Base Station

    I have an Airport Express Base Station I had recieved from a friend of mine. It is a 802.11n Wi-Fi Station, and I'm running OSX 10.7.4. When I open airport utility 6.0 it can't find my devie and the same with Airport Utility 5.6. I've tried resetting the station and plugging it directly into the computer via ethernet cable but nothing has happened. Someone help?!

    Nevermind, I figured this one out. Just perform a hard reset. Unplug the base station, push and hold the reset button then plug the station back in while still holding the button in. Continue holding till the the LED flashes yellow really fast. Release and wait till the Airport Express starts up.

  • Samsung CLP-300 attached to Airport Express Base Station: Issues

    I have found that my Samsung CLP-300 printer, which is connected to my Airport Express Base Station via USB, refuses to print after printing one document. After restarting my Airport Express Base Station, I found that the printer would start printing again, but only one document - afterwards, I required a base station restart before the printer could print again.
    Does anybody know how to rid this problem? I would like to be able to print consecutive documents without needing a reboot.

    Hi Eric. I've had the same troubles for quite some time. I've had limited success setting the printer up as an IP Printer. Here's a link to another discussion that might help you out. Good luck!
    http://discussions.apple.com/thread.jspa?messageID=8804705#8804705

  • I want to re-use my old airport express base station but airport utility doesn't recognise it anymore (it dates from 2005) i would like to use it to connect to my speakers only

    I have an old airport express base station from 2005
    I would like to have a network on it so i can put it upstairs in a room and connect my speakers to it so i can send my music (from itunes) over the airport to my speakers.
    I reset it and now i want to configure but the Airport utility doesn't recognise it anymore.
    Can i update the firmware? has it become useless because too old or what can i do?
    I work on macbook pro with macOSX 10.9.4
    Can someone give me some tips please
    thanks
    J

    Please locate the model number on the side of the AirPort Express. Hard to see.....gray lettering on a white background....so you may likely need a magnifying glass and good lighting to see it.
    The model number starts with a "A" followed by four numbers. If you see A1084 or A1088, unfortunately AirPort Utility 6.x in Mavericks OS X (10.9.4) does not support these older models. However, you can still administer these models if you have a Mac.....or can borrow one for a few minutes....using Leopard (10.5.x) or Snow Leopard (10.6.x), or a PC with AirPort Utility installed on the device.

  • Steady green light on A1084. Airport Utility 5.6 says set up is complete.   Airport Express base station does not appear in the menu bar, so I cannot select it.  Is there a fix?

    Steady green light on A1084. Mac OS X 10.7.5. IMac. Verizon DSL Actiontec GT704-WGB modem. Airport Utility 5.6 says set up is complete.   Airport Express base station does not appear in the menu bar, so I cannot select it and send a signal to airport express to play airtunes through my stereo amplifier.  Is there a fix?

    I plugged a model A1034 Airport Extreme Base Station into the Verizon DSL Actiontec GT704-WGB modem with an ethernet cable and now the AirPlay icon appears in the Itunes window immediately to the right of the volume control and I can select it and play Airtunes wirelessly through the A1038 Airport Express Base Station in another room connected to a stereo amplifier by a Monster mini-to-RCA left/right audio cable running from the output jack on the A1034 Airport Express Base Station into the CD jacks on the amp.  The problem is that I have to select the Apple Network Airport Express Base Station as my network in order to select the Airport Express Base Station when I click the AirPlay icon, which means I have no Internet signal to the Imac. If I select the Airport Extreme Base Station or the Verzion modem as my network, then I have an Internet signal to the Imac, but the Airport Express Base Station is grayed out when I click on the AirPlay icon, so I cannot select the Airport Express Base Station and send tunes to the Airport Express.  It would be nice to play Airtunes while simultaneously accessing the Internet.  I don't understand your question about what program I am using for which I require AirPlay.  I am not learned about computers in general, and even less so about Macs than PCs.  I thought the program I was running was Itunes, and there was no separate program to run to use AirPlay for the purpose of sending a signal from the Itunes on the Imac to the A1084 Airport Express base station in a another room, and then out as described above to the stereo amplifier to listen to Itunes music remotely in the other room, without any kind of cable, wire, etc., connecting the Imac to the stereo amplifier.  I would guess that the most common use for the A1084 is to play Itunes through a stereo in another room without the need to run wires from the computer to the stereo.  I realize it would be easy simply to run a very long mini-to-RCA left/right audio cable across the floor connecting the Imac to the amp without the need to use AirTunes, Airplay or any kind of AirPort, but it would be both unsightly and a tripping hazard.

  • Can I use the AirPort Express Base Station as a wifi 'reciever'?

    I have a AirPort Extreme base station connect to the internet in my living room. But my bedroom is a little far from the living room so that I cannot revieve a good wifi. I want buy a AirPort Express Base Station to put in my bedroom connecting my PC. Will this way work to make my PC's internet faster??

    Hello:
    You can extend a wi-fi network like this:
    http://support.apple.com/kb/HT4259
    That will not increase speed, but it will improve reception.
    Barry

  • Apple AirPort Express Base Station with 802.11n - MB321LL/A. How to set it up to my new iMac

    Community:
    How do you set up an
    Apple AirPort Express Base Station with 802.11n - MB321LL/A how do you set up on Mac running on OS X 10.9.4?
    Please advise
    Fmsalazar

    Apple did say it was important.
    If the units do not show up in the airport utility then you must set it correctly to link-local.
    Steps for OS X Lion or Mountain Lion
    This can happen if IPv6 has been disabled. To enable IPv6 for your network interface:
    Choose Apple menu () > System Preferences, and then click Network.
    If a lock icon appears in the lower-left corner, click it and enter your admin name and password to unlock the pane.
    Click your network service (Wi-Fi or Ethernet) in the list, and then click Advanced.
    Click the TCP/IP tab.
    Choose Link-local only from the Configure IPv6 pop-up menu.
    Click OK.
    Click Apply.
    AirPort base station not seen or "An unexpected error occurred" appears in AirPort Utility 6.3
    Apple rep says the same.
    Re: Unexpected error when connecting Airport Express A1264 to Airport Utility 6.3.1
    I am searching as I saw it in a thread today where a person had issues. (No contribution from me in the thread but found that was the issue).
    It is kind of a fail safe.. since auto can end up with any setting.. and it will depend on the setting of ipv6 in the Airport Router if it works properly in the computer.. setting it to the correct value is one step in sorting out problems when people get in a mess.

Maybe you are looking for