Airport Express: Can music be Streamed to AE with WEP ?

Hi:
I have been trying to get iTunes to stream music from my HP laptop to AE
when my network is password-protected via WEP-64. Well, can this even be done
using the latest version of Apple's AE ? According to P. 26 of the Airport Express Setup Guide, under the section "*Allowing Wirless Clients Access to Your Network*", it states "+If your network is password-protected using WPA Personal or WPA/WPA2 Personal, you can provide wireless clients access to your network without them to enter the network password+." It then goes on to talk about providing clients access via setting up an Access Control List (ACL) in Airport Utility.
So, the question is...drum roll please...
Can iTunes stream music from my HP laptop to AE, wirelessly ,
when my network is password-protected via WEP-64 ?
I know it can do it via a wired (Ethernet cable) connection...
I am currently doing it.
Thanx
DaleB

Hi:
I have the latest AE ... 802.11 n
Does anyone know if Apple has maybe changed the AE software/firmware/hardware where the AE may not work WEP-64 ?
Thanx
DaleB

Similar Messages

  • How many airport express can  i install in my home to stream music?

    I plan to buy many airport express in my new Home!
    how many airport express can  i install in my home to stream music?
    Jimmy

    jimmyflo wrote:
    I plan to buy many airport express in my new Home!
    how many airport express can  i install in my home to stream music?
    Theoretically as much as you want but there are technical limitations about the usable bandwidth in the wireless or by the used access point.
    All participants (stations) in a wireless network share the available bandwhith equally and therefore a point will get reached where the throughput in the network became insufficient to stream music.
    Also some routers limit the number of stations could get connected. For instance Apples Airport Extreme have a limit of 50 connected clients and the AP-Express (if used as access point) a limit of 10 simultaneous connections.
    Lupunus

  • While using the airport express can I listen to music streaming from the Internet?

    While using the airport express can I listen to music streaming from the Internet?

    The music must be in your iTunes library.
    Or, you can try to add a special application like Airfoil that may allow you to stream any audio signal on your computer to the AirPort Express. It might work.
    http://www.rogueamoeba.com/airfoil/

  • Airport express only music streaming

    Good morning,
    I just want to you use airport express for streaming music conneting a receiver and my mac pro book.
    I don´t wanna go into the internet.
    What to do?
    I´m using a fritzbox 3270 for internet, phone, etc.
    Thanks in advance.
    Michael

    You basically have two choices and they are dependent on whether or not you want to "switch" wireless networks between accessing the Internet and streaming.
    The AirPort Express can be used standalone, meaning that you do not need to connect it to a network or the Internet in order for it to provide a Wi-Fi network for streaming. However, if you do so, you will (again) have to switch which wireless network you will connect to in order to do so.
    If this works for you, then I can provide the set up instructions.

  • Using airport express to extend network/stream music

    Hi,
    I just bought an airport express to extend my network throughout my house and stream music to my stereo system in my living room. My time capsule, which is connected to the DSL modem and is the base station, is in one far end of the house, while the airport express is at the other end. It has greatly improved the range of my network and when using my macbook in the front room, it gets full bars, however, the when using airtunes to stream music with iTunes 9 and OS 10.6, the music will cut in and out randomly and I occasionally get unknown error -15000 when trying to connect.
    I played around with the airport express channels (any channel other than 10 will receive an unknown error -15000 automatically,) adjusted the firewall, and adjusted Netbarrier X, my third party security software. I found information in this article:
    http://support.apple.com/kb/TA21538?viewlocale=en_US
    The only thing that works is moving the airport express close to my computer to remove the physical barriers. It plays perfectly then. Is it possible to buy a second airport express and plug it in halfway between my stereo and time capsule to boost the signal to the airport express plugged into my stereo? Will this solve the problem of the music stream cutting in and out every 10-20 seconds?

    Mad Cow wrote:
    I checked and my signal is -87 and noise is -95.
    At the risk of being the bearer of bad news, that's a rather poor signal value. Here is a description of what different ranges of signal-to-noise mean:
    http://discussions.apple.com/thread.jspa?messageID=10329543&start=1
    In the other post, you mentioned interference from other electronics. Could physical barriers be causing interference also?
    Barriers won't cause interference, but they can reduce signal transmission. How far apart are the two units, how many walls are in between, and of what material are those walls made?
    If this is the case, can I add a second airport express between my base station and stereo-attached airport express to boost the signal?
    In theory something like that might work, but I'm not sure that an AirPort Express can act as a "relay" station between a "main" station and a "remote" station. It might require an AirPort Extreme. Perhaps someone else can comment on that possibility.
    Can you relocate your Time Capsule to an different phone outlet? Can you use longer cables between the wall and the modem and/or between the modem and the Time Capsule to move the Time Capsule to the other side of the room to be nearer to your AirPort Express? Can you use a longer audio cable between your AirPort Express and your sound system?
    You may be able to use a pair of Power-Line units
    (http://computer.howstuffworks.com/power-network.htm) to connect your AirPort Express to your Time Capsule via Ethernet.

  • If i have a home full of Apple TV's and Airport Express' can i  airplay music in every room at the same time?

    If i have a home full of Apple TV's and Airport Express' can i  airplay music in every room at the same time?
    Or just one device(room) at a time?
    It seems there is a lot of home theater systems where they all hook up to one "control" and then disperse to the different locations per instructions..
    Is this possible with all apple products?

    From iTunes using Multiple Speakers (you can control with the Remote app on iPhone/iPad too), but not from AppleTV itself.

  • Hello i have a problem with my airport express the music sizzles? Why?

    Hello i have a problem with my airport express the music sizzles? Why?
    What can i do?

    Does the game has the same iOS requirements that your phone has? Games needing iOS7 will not install on iOS6 and earlier.
    Did you try to download it to your computer and sync it to your phone after that?
    If you can't connect to the iTunes Store, try these suggestions:
    Can't connect to the iTunes Store

  • How many airport express can I add to my network for the purpose of using the airport express to send audio signal to different rooms in the house? I'm interested I'm running about six different zones.

    How many airport express can I add to my network for the purpose of using the airport express to send audio signal to different rooms in the house? I'm interested I'm running about six different zones.
    What I'm looking to do is to have self powered in ceiling speakers in every room in my house with out having to run wires to every room to carry the audio signal. I would like to use the airport express to do the job of carting the audio signal.
    Here's my set up now I have an airport extreme and one airport express that I use to carry audio to one room.

    FWIW. I have used up to four AirPort Express Base Stations (AX) for streaming sucessfully in pretty much the way you have described. I didn't have a need to try more so I can't attest that more would or would not work.

  • Love airport express for music throughout the house but it goes dead from time to time

    Airport Express for music just goes dead
    is there a quick fix to this

    You don't really want 2 wireless networks. After you get the Linksys set up, you will want to configure the AirPort Express (AX) to join the wireless network created by the Linksys base station. You will then have one wireless network that provides Internet and wireless music streaming.
    Use the directions in KB 302153, AirPort Express: How to join an existing wireless network in client mode to configure the AX.

  • I have an Ipad and Iphone but I don't have an Airprint, only a WIFI printer,my question is if I connect the wifi printer to Airport express, can I print from Ipad and Iphone ?

    I have an Ipad and Iphone but I don't have an Airprint at home but only a WIFI printer, my question is if I connect the wifi printer to Airport express, can I print from Ipad and Iphone ? Please help me if anyone knows about this.

    Unfortunately, connecting a non-AirPrint-enabled printer to an AirPort base station's USB port will not make it AirPrint-ready.
    You will need to use another solution, like Printopia, to be able to print to this printer from an iOS device.

  • After updating Time Capsule to 7.7.2, Airport Expresses can no longer connect

    After I update the Time Capsule firmware to 7.7.2, my three Airport Expresses can no longer connect to the Time Capsule (their orange lights blink and they appear inaccessible in the Airport Utility). When I downgrade, they are able to connect fine.
    They are connecting to the Time Capsule over my 5GhZ wireless network.
    Any help?

    Hi yonajon!
    I have some resources for you that may help you resolve this issue. First, here is an article about addressing the blinking amber light:
    Wi-Fi base station: Understanding and resolving a blinking amber status light
    http://support.apple.com/kb/ts1589
    If you are still having issues, you may need to reconfigure your extended wireless network:
    Wi-Fi base stations: Setting up and configuring an extended wireless network (802.11n)
    http://support.apple.com/kb/ht4259
    Take care, and thanks for visiting the Apple Support Communities.
    -Braden

  • How many airport express can be supported by software remote at one time.

    how many airport express can be supported by software remote at one time?
    I mean remote software can control at one time

    Well Apple makes an iOS application called 'Remote' it's used to control iTunes on a Mac, Or to control an Apple TV Multimedia features.
    Apple also makes "AirPort Utility" for iOS. Airport Utility can be used to configure Aiport Extrem, Airport Express And Time Capsul using an iPad, iPhone or iPod Touch. You can use it to connect to one device at a time. While connected to the device you can configure it to work as part of a larger Airport network. If you want to configure muliple device, you would connect to one device,  configure it,  And then connect to the next device, and configure it, and so on and so fourth.
    I haven't found a limit.
    How big of a network are you trying to make?

  • Airport Express can only extend network, not create new one. Why?

    I am sharing a flat with some friends. The shared broadband router is placed in the living room. To strengthen the signal and make it easier for me to manage, I bought an Airport Express, connected it to the shared router with an ethernet cable and set up a wireless network of my own in my room. It was working fine, until recently we renewed our broadband contract. The router had been replaced by a new one (I don't know why) and the network configration had been changed. Since then I was not able to use my own network. In the Airport Utility display, the light of Airport Express is green, but the light of Internet is yellow, and the status is disconnected. I tried to change various other configuration on the Airport Express, and all in vain. Until I switched the network mode from 'Create a new wireless network' to 'Extend a wireless network', the Internet connection was finally back online. But this merely extends the existing network and not what I want. Why this happens? Why my Airport Express can only extend a network, not create one?

    Here is the situation on my Airport Express.
    If I choose to extend the existing wireless network, the Airport Utility shows like this:
    If I set up a wireless network of my own, what I get in the Airport Utility is this:
    See my problems here? The Airport Express does not show anything in amble, but the Internet complains that there is no connection.
    This problem did not occur before the broadband was renewed and the rounter was replaced.

  • Airport express can't extend wireless network

    Airport express(A1264) can't extend wireless network. It seems that Airport express can't find my home Wi-Fi network. Amber light is blinking, and AirPort Utility of MacBook also can't find Airport express.
    If AE is connected with TC via LAN cable, amber light is blinking with message "Wireless Network" (This Airport base station is set up to join a specific wireless network that can't be found...)
    It was successful only once, but all failed after that.
    Is there solution for this problem?
    [My system]
    Time capsule 4th generation
    Airport express 1st generation (A1264)
    [Settings]
    Time capsule (ethernet connected)
    - Create a wireless network
    - 802.11a/n - 802.11b/g/n (Automatic)
    - 2.4GHz / 5GHz Channel (Autmatic)
    - WPA2 Personal
    Airport express
    - Extend a wireless network
    - WPA2 Personal
    - 2.4GHz Wi-Fi network name and Password is set up

    If AE is connected with TC via LAN cable, amber light is blinking with message "Wireless Network" (This Airport base station is set up to join a specific wireless network that can't be found...)
    Sorry, I misunderstood what you wanted to do.
    Since you did tell us that you had the Express connected with an Ethernet cable, I assumed that was how you wanted to configure the Express.
    But I want to extend a wireless network (not using ethernet)
    Because Airport Express and Time Capsule cannot be connect via ethernet cable.
    Follow the same setup as above....and do not connect an Ethernet cable.
    Keep the Express near the Time Capsule for the setup. Once you have a green light, move the Express to a point that is about half way between the Time Capsule and area that needs more wireless coverage.
    If you reset the Express several times and try the setup several times without success, I think you have to suspect a defective Express.

  • Airport Express can find my printer (Lexmark z55) but cant print ?

    Hi
    At home i use Airport express with lexmark z52 and all work fine ...
    At my parants house they got a Airport express with a lexmark z55 and the Airport express can see the printer but when i try to print it says "Problem communicating with the printer" ive tryed to disable firewall but that didnt help.
    Ive tryed with a HP deskjet 450 and it works with that one ...i think its the Lexmark driver (i tryed these ones http://downloads.lexmark.com/cgi-perl/downloads.cgi?ccs=229:1:0:339:0:0&searchLa ng=en&os_group=WinXP&target= )
    but no luck ...im running WinXP
    So if you got any idea please lemme know
    Best Regards
    Michael Fog
    Ps : I have also tryed the Bonjour program no luck

    Ive tryed with a HP deskjet 450 and it works with
    that one ...i think its the Lexmark driver
    Problems with finding Printer Driver on Windows XP when using printer connected to Airport Extreme or Express
    http://www.ifelix.co.uk/tech/1012.html

Maybe you are looking for

  • Opening the Canvas window and the Timeline from the browser

    I am on an Intel 2x2.66 Dual Core using OS 10.4.11 and working in FCP 6.04. I know this is a stupid question but having been a composer all my life, I am not up to speed on FCP and I seem to be unable to find the answer in my manual. I dragged a Quic

  • How to change DVD player sleep time

    I have some DVDs that I like to repeatedly play video clips from. However, I'm having a problem with the DVD player going to sleep before the clip finishes, resulting in a very noticeable delay and message "waking up DVD player" when the time comes t

  • How to configure .ocx file in a JSP page

    Hi i am doing a project which involves data retrival from a Swipe card. I am going to retrive the id from the card and this data has to be sent to a JSP page. After retriving the ID from the card, we access the database and retrieve all the informati

  • Gmail Mobile App 2.0

    New version: http://googlesystem.blogspot.com/2008/10/gmail-mobile-app-20.html reg

  • SOAP Sender & Receiver Adapters

    Hi I want to use SOAP adapter on both sides of XI. Since its way different from other adapters, could someone tell me how to make use of it. Will I be able to trigger a process on the 3rd party application and receive a payload from it  using Sender