Airport express cannot be found in Airport Utility

I went and changed my network on my Mac.I thought I was just changing the name but realized I created a whole new network. Now my airport express (which is used to stream all of my music from a receiver to my speakers in each room) is not recognized in Airport Utility. I have done a hard reset, factory reset, unplugged modem, base station (airport extreme) and express and it still wont appear. Please help!. I have tried plugging it in right next to my computer but still amber flashing light. I don't have a LAN wire to take out of another device and try it thru the computer.

You son't want to set a static IP address on the Express, it will get that from the DHCP server up stream.
If you now have the Express setup with the correct network name and password to match the rest of your network, best thing to do is shut every device down...doesn't matter the order. Then power each up, and now the order DOES matter. Start with the modem and give it time to stabilize, a minute or two, then the next piece in line, an Extreme or Time Capsul if that is what you are using, then the Express, then the computer. These have to go in order so they get there IP addresses straight and you don't have conflicts.

Similar Messages

My HP C5280 printer with Air Port Express cannot be found on my IPad . Any suggestions?

MYIpad Wi Fi cellular cannot connect to my HP c5280 printer with AirPort Express.

It appears that the HP C5280 is not an AirPrint compatible printer, so I would not expect it to work when you try to print from an iPad.......unless you want to try to install additional software.....like Printopia.....on a Mac on the network to see if that might allow printing.
There is a free trial with Printopia, so if you want to give it a try, you will know if it will work before you buy. More details in the link below.
There are other Apps that perform this type of service as well, but I have not used them. Hopefully, other users will have some other suggestions in that regard.
Printopia - Ecamm Network

HT5022 Airport Utility 5.6 does not fix the old Airport Express!

My old airport express does not work anymore - the Airport Utility 5.6 makes changes but after re-starting, the Airport Express cannot be found. Now I am forced to buy a new one. Not good (and sold out as many experienced the same apparently)

Do you get any sort of error message when you try to install, and if so what does it say?

BIOS Flash Utility Fails with "BIOS directory cannot be found"

I download the 32-bit BIOS update 6fuj35us.exe and ran through the ThinkPad BIOS Update Utility Setup Wizard. After I click Finish I accept the option to update my BIOS. It fails to start the flashing process, with the error popup: "BIOS directory cannot be found. The utility process cannot be completed." I tried the ISO image too, it burned and booted up correctly, but I got the exact same error message when I tried to run the flash.
Has anyone been able to get over this issue?
Thank you
Solved!
Go to Solution.

I had to send my machine back for a motherboard replacement. Fortunately, they turned it around quickly, two days, as quickly as the shipping allows.

Cannot configure my AirPort Express (1st generation) anymore. Am using AirPort Utility 5.4.2 Setup Assistant. What do I do wrong?

I cannot configure my AirPort Express (1st generation) as base Station anymore. I had to reset it because I lost my password.
I first tried my IPads (IOS 6). These returned the message: Your AirPort Express cannot be configured with this software. Go to apple.com/nl/support/airport for more information.
As it is an old one, I have downloaded the eldest available AirPort Utility I could find on the Apple site (AirPort utility 5.4.2) to my computer. I ran the AirPort Setup Assistant wireless and the assistant found my AirPort named " Apple Network XXXXX". (I notes that the Assistant also returned the message: If this is not the AirPort Extreme you want to set up ...)
I clicked <NEXT>
After trying to connect to Network, I received the message: Cannot connect to network or there are no AirPort base stations on the network.
To be sure I retried running the Assistant after connecting the computer and the AirPort using an ethernet cable. The error message was the same.
What do I do wrong?
Am I using the wrong Utility software? If so, which version do I have to download and from where?
Is a first generation AirPort anyhow compatible wth 4the generation IPads or shoud I just buy a new AirPort.
I hope someone can help me...

Ok, thanks for clarifying that for me. You are correct. Your iOS devices will NOT be able to administer the 802.11g base stations because the version of the AirPort Utility that they use is incompatible.
For Windows XP, AirPort Utility for Windows v5.5.3 should work. However, v5.4.2 that you have should work as well.
Your XP computer needs to connect to the AirPort's wireless network BEFORE you can access the AirPort with the AirPort Utility. You may want to try connecting your computer directly to the AirPort using an Ethernet cable.

Airport utility cannot find Extreme nor Express, but internet is working?

I have an airport extreme base station and and airport express (as a wireless extender and media speakers)
When my iMac wakes up from sleep, airport utility cannot find any devices.
- internet works as usual
- airplay doesn't work (via my ipod or my iphone)
- apple TV 2 can't find the itunes library.
- in system preferences -> network - my network seems to be all ok and when I turn off airport and on again, both devices suddenly appear in the airport utility. But when the iMac goes to sleep, same problem happens.
- I have made ensured that my network is the preferred network but still the problem persists.
as the internet is working, there doesn't appear to be a problem. However, when airplay and apple TV are not working properly, this is a problem!
Grateful for any help. Thanks.

My Airport utility cannot find my base station either, and I can't print. But I can access the Internet!
The base station just "vanished" one day after working perfectly for about two months. I first discovered this when I was unable to print - I began troubleshooting by entering the utility, only to discover the base station was not listed.
I finally deleted my networking settings in Vista, and then did a factory reset on the Aiport Extreme. I then set everything up from scratch again to successful resolution.
Then again one day a short time after that, it vanished again! In frustration, I disconnected Airport and put it away. I tried setting up a new Dlink I purchased to replace the Airport, but the Dlink didn't work either!!! Dlink tech support couldn't fix the problem and suggested I get my money back. I then, as a last ditch attempt, reconnected the Airport. It automatically found the base station without me doing anything besides just hooking it back up!
It worked for about two weeks and now it vanished again! The utility upgrade released the other day has not fixed this problem. I guess I'll delete networking connections again in Vista, and do a factory reset to Airport again.
I guess Airport and Vista just don't play well together.

HT1349 Airport Utility cannot find my Extreme or Express?

Airport Utility cannot find my Extreme or Express?

Hi, found an answer to this on web
1) Ensure that AE is sending a signal out (ca. 45s after at reset)
2) To see this signal first go to the wifi and connect to the net that AE send out - name: "Apple xxxxx.."
3) Start up Airport Utility and AU will now see your AE
Finish and configure

The Airplay Device "Airport Express Y" cannot be found on your network

I keep getting this iTunes error. I have a couple of sets of speakers each connected to a seperate Airport Express N (1G) which I will refer to as Airport X and Airport Y. The error always specifies the problem is with my Airport Y. When this error occurs iTunes switches from my AirPlay multiple speaker setup to the default single Computer speaker connection. The only way to resolve this is to go into iTunes and switch the AirPlay speakers 'back on'.
Both of my Airport Express have the latest firmware 7.6.3. They are connected wirelessly to an Airport Extreme Base Station which is also 7.6.3. AirPlay is enabled on all devices. The Airport Express are connected to my network as "extend this network".
The configuration all looks ok. The only thing that differs about the Airport Express is that I bought the Y device on eBay, but other than this issue everything about it seems to be fine.

The AirAirPort Express and AirPlay. Trying to set up streaming to one of two airport airport express within my network within iTunes. I keep receiving the following error message on just one unit "The AirPlay device “XXXXX” cannot be found on your network. Please verify your network settings and AirPlay configuration or select another device."
iMac (27-inch, Late 2012), OS X Mavericks (10.9.5)
iMac with 3.4GHZ Intel core i7, Memory 16GB
Running OSX 10.9.5
Airport utility 6.3.2
Within Airport Utility I can see and program this unit and i checked to ensure that Airplay was checked. Did not see anything in the forums about this type of issue.
Please advise.

I can no longer access my Airport Express Base Station. When I plug it in, it keeps flashing orange. I cannot see it in the Airport Utility.

I can no longer access my Airport Express Base Station. When I plug it in, it keeps flashing orange. I cannot see it in the Airport Utility.
How do I fix this

If you're comfortable resetting all settings, unplug it, hold down the reset button and keep holding it in as you plug it back in - keep holding it for another 10-20s until the amber light flashes
Then, open airport utility, now you should be able to see the device either on-screen or in the upper left under 'other wi-fi devices'

Cannot connect to AirPort Express after setting it up in AirPort Utility

I have two PCs: one has a Linksys WMP54G wireless card to connect to my AirPort Express which is connected to a wired Linksys ethernet router; the other has an ethernet card which is also connected to the Linksys router. My cable modem is plugged into the router in order to provide internet access to both PCs. I came home from work yesterday to discover that my wireless PC could not connect to my AX. I have had the AX for over a year and it has pretty much worked fine up until yesterday. And it has worked fine for the past couple months connecting to the cable modem via the Linksys router. Connecting to the internet on my wired PC is no problem at all.
First, I tried unplugging the cable modem and the AX, but no luck. After reading these discussions, I tried doing a hard reset on the AX and going through the AirPort Utility setup, but still no luck. I tried this several times, trying to configure it using both WEP and WPA. I think I originally had it set up as WEP, but when I reinstalled Windows at one point, I think I configured it as WPA (and it worked fine). I am not sure if this may be part of the problem When I reset the AX, it will eventually show up on the Windows Wireless Network list as an "Apple-09s8f23" unsecured network. Once I connect, I run the AirPort Utility (v5.3.2) and it detects it no problem. But after I go through the configuration process in the AP Utility, it gives me an error message: "AirPort Utility was unable to find your Apple wireless device after restarting...etc.". Meanwhile, the network still shows up in my Windows Wireless Network list, but cannot connect to it, and the light on the AX is still green. I have tried unplugging the ethernet cable to the AX, moving the AX to the same room as my wireless PC, and repeating the reset-configuration process, but still no luck, so I don't think it has anything to do with the Linksys router or the cable modem.
Sorry for the wordy post, but does anyone have any advice or suggestions? Any help would be greatly appreciated!
Thanks in advance,
Dave

So I went back to the PC after my original post, and somehow I was able to connect to the AirPort wireless network in the Windows Wireless Network List. Once I did this, it showed up in the AirPort Utility, and I was able to access the internet. I have no idea what fixed the problem, but maybe it was simply a matter of waiting a few minutes before connecting to the network?

Why can't my Airport express be found by the airport utility?

Why can't my airport express be seen by the airport utility?

I have the same problem.
I have a Mac Pro OSx10.7.5, a Netgear router, A 1st gen Airport Express Model A1264 set up in Bridge Mode w/ LAN cable as Network 2 for Airplay, the iPad palys music and connects to the internet great through it. I want to extend Network 2 to another set of speakers in another room so I bought another AE A1264. "Like new"
So far I cannot get the computer to see the new AE at all. I have tried it wired to the router, wired to the Mac, wireless near the 1st AE, I've reset it and restarted multiple times. It just isn't showing up at all. ZIP. I get a slow blinking yellow light.
The Airport Utility "Configure Another"comes up with a Mac address I haven't seen before. I don't know if it's the new AE or not. In any case none of the passwords including " " for a password work. It spins and I get an error message that "An error occured while reading the configuration"
Even when it was new the first AE took some doing to be seen by my Mac which was plenty annoying since it should just pop up but it did eventually connect via LAN. Once I configured it it worked on my network.
These things have been a real pain. Please advise.

Airport Extreme and Airport Express are not found on the Airport Utility. Internet still works. Huh?

Good People,
I have an Airport Extreme serving as my wireless router with an external hard drive connected to it. I also have an Airport Express in another room connected to a stereo for Airplay. Neither can be found on the Airport Utility (v5.5.3), but wireless internet still works. This happens often, with both reappearing in Airport Utility for short amounts of time periodically. What's the deal? Both the Extreme and Express are less than 6 months old. It's a bit frustrating not getting tunes when you have everything set up right and not being able to use Time Machine consistently.
All recommendations appreciated.
Thanks.

shakeelium wrote:
Good People,
I have an Airport Extreme serving as my wireless router with an external hard drive connected to it. I also have an Airport Express in another room connected to a stereo for Airplay. Neither can be found on the Airport Utility (v5.5.3), but wireless internet still works. This happens often, with both reappearing in Airport Utility for short amounts of time periodically.
I've once had the same problem.
The reason for that issue is the frequency (radio band) hopping of the station.
On your AP-Extreme
Enter the manual setup
Disable Guest Network if not desperately needed
Set a dedicated name for the 5GHz wireless (wireless -> wireless options)
Eventually change the radio mode (if no 802.11b/g systems in your home) to "only 802.11n (5GHz) - only 802.11n (2.4GHz)" by holding down the option key *alt* while clicking on the drop down.
On your Mac
Disable (switch off) wireless
Enter system configuration -> network -> wireless
Uncheck "Ask to join new networks"
Enter advanced options and check that your wireless name is in the first position of the list. If not, drag it with the mouse to the first position.
Click apply
Join your wireless again and try to connect to the 5GHz name (SSID) because the 5GHz will improve the connection speed of your Mac remarkably.
Eventually you might change the settings on the Express too.
Check the location of the AP-Extreme.
It should NOT be placed: On the floor, in a corner, behind furniture, near metal objects, life high voltage wire or cordless phone bases.
It should be placed: As high as possible (up on a shelf or ceiling mounted) with a maximum line of sight to all stations, even thru walls.
If your home situation allows that, try to use the 5GHz band only. If you own a iPhone this must use the 2.4GHz radio.
Lupunus

Steady green light on A1084. Airport Utility 5.6 says set up is complete. Airport Express base station does not appear in the menu bar, so I cannot select it. Is there a fix?

Steady green light on A1084. Mac OS X 10.7.5. IMac. Verizon DSL Actiontec GT704-WGB modem. Airport Utility 5.6 says set up is complete. Airport Express base station does not appear in the menu bar, so I cannot select it and send a signal to airport express to play airtunes through my stereo amplifier. Is there a fix?

I plugged a model A1034 Airport Extreme Base Station into the Verizon DSL Actiontec GT704-WGB modem with an ethernet cable and now the AirPlay icon appears in the Itunes window immediately to the right of the volume control and I can select it and play Airtunes wirelessly through the A1038 Airport Express Base Station in another room connected to a stereo amplifier by a Monster mini-to-RCA left/right audio cable running from the output jack on the A1034 Airport Express Base Station into the CD jacks on the amp. The problem is that I have to select the Apple Network Airport Express Base Station as my network in order to select the Airport Express Base Station when I click the AirPlay icon, which means I have no Internet signal to the Imac. If I select the Airport Extreme Base Station or the Verzion modem as my network, then I have an Internet signal to the Imac, but the Airport Express Base Station is grayed out when I click on the AirPlay icon, so I cannot select the Airport Express Base Station and send tunes to the Airport Express. It would be nice to play Airtunes while simultaneously accessing the Internet. I don't understand your question about what program I am using for which I require AirPlay. I am not learned about computers in general, and even less so about Macs than PCs. I thought the program I was running was Itunes, and there was no separate program to run to use AirPlay for the purpose of sending a signal from the Itunes on the Imac to the A1084 Airport Express base station in a another room, and then out as described above to the stereo amplifier to listen to Itunes music remotely in the other room, without any kind of cable, wire, etc., connecting the Imac to the stereo amplifier. I would guess that the most common use for the A1084 is to play Itunes through a stereo in another room without the need to run wires from the computer to the stereo. I realize it would be easy simply to run a very long mini-to-RCA left/right audio cable across the floor connecting the Imac to the amp without the need to use AirTunes, Airplay or any kind of AirPort, but it would be both unsightly and a tripping hazard.

Airport Utility cannot find my Airport express on Windows 7

   I have a working Airport express with a static ip address. The static ip address has been hard coded in my main router. The airport express is connected to my network via ethernet cable. Airport Express Version 7.6.1. I am having conectivity issues from my new Windows Desktop. The airport utility 5.6.1 on my new desktop cannot find my airport express. The manual setup button has been greyed out. I can ping the device. I can click on "configure other" and configure the airport-express (which is how I set it up).    If I reboot my desktop and then quickly fire up the airport utility, it finds the device. On hitting rescan, in a few minutes everything gets greyed out again.
The airport utiltity on other computers is able to find that airport express.   I am able to stream music through the airport express from other computers in the network.
How do I find out what is blocking the airport utility on my new desktop. The Bonjour Service is up and running.   Any help/advice on trouble shooting this issue is appreciated.

The airport utiltity on other computers is able to find that airport express.   I am able to stream music through the airport express from other computers in the network.
You only need one computer on the network to access the settings in the AirPort, so unless you like to look for things, it is probably not worth the effort to try to troubleshoot the blocking action on the Windows 7 machine.
It is not always the Windows Firewall and/or the anti-virus program that blocks connection attempts like this, but that would be the first place to look.
In general, you have to get into the Firewall settings to create an "exception" for the AirPort connection. The same would be true for the anti-virus if that is what is blocking the connection attempt between the PC and AirPort.

My Apple Airport Express is blinking Amber and I cannot find it with the utility

My Apple Airport Express is blinking Amber and I cannot find it with the utility

Hi, had the same problem -
1) Connected AE to Time Capsule with Ethernet cable - Configured it - All worked fine
2) Removed Ethernet cable between AE og TC - All worked fine
3) Unpluged my AE from the socket outlet (power off) and pluged it inn where its supposed to be (2m from my Time Capsule)
4) Now Airport Utility do not find me AE (after all i reconfigured through the Etheret calbe) ????
A) Seems that Airport Utility are not able to "see" any wireless AE, only configurable by Ethernet Cable.
B) Seems that AE are not able to reconnect to configured network after a power loss.
This is a little bit ****** - older airport utility had none of the problems (A and B)

Airport express cannot be found in Airport Utility

Similar Messages

Maybe you are looking for