Airport Express Conflicts with Clear Wireless Network?

After months of stumbling around, trying to figure out why my Clear Wireless internet service was so choppy, I finally plugged the ethernet cable directly into my computer, and disabled my local Airport network. Voila! Works like a charm -- very fast and reliable, now. Trouble is, I don't have network access for my laptop. The problem (I suspect) is that I also have phone service on my Clear modem.
Here's what the connection looked like (and was recommended by Clear Wireless), with <-> meaning wireless connection and <+> meaning an ethernet connection:
computer(s) <-> Airport Express <+> Linksys Phone Box <+> Clear Modem <-> Clear Tower
So, pulling the Airport Express out of this sequence cleared up ALL of the stalling problems and slowness. My new (and functioning) set up looks like this:
computer <+> Linksys Phone Box <+> Clear Modem <-> Clear Tower
My question is whether I can have somehow connect the Airport Express on the other side of my computer, and allow my local network access the Clear Wireless modem via my computer? Right now, I've got the Airport Express plugged in and running, mostly to check if there was simply an interference problem, and that doesn't seem to be the case (the phone connection is a base station with wireless handsets, so thought there might be interference there -- doesn't seem to have been an issue).
Any advice on this would be great. Clear Wireless is as clueless on technical support as it is brilliant in concept. Still very much in startup mode, with phone operators reading from generic scripts and masses of angry users spamming their discussion board -- ugh! Thus my post here. I'd love to see a schematic that shows the optimal way to bring a phone connection into a local wifi network.
Thanks!

What I would like to do is to connect the airport express to the wireless network (Linksys-router).
What are you trying to do with the AirPort Express Base Station (AX)? Use it for streaming iTunes and/or share a USB printer, or extend your existing Linksys wireless network?

Similar Messages

Airport Express Problem with Wired/Wireless networks simultaneously

Hello,
I'm having trouble maintaining a connection with my AX (2012) in a work environment. Basically, I have a Win 7 laptop connected via ethernet to the internet/corporate net. I have configured the AX to create a separate wifi network that does not connect to the internet. In order to connect to the AX, I have to disable both the Ethernet adapter and the WLAN adapter, enable the WLAN adapter, connect it to the AX's network, and wait for it to show up in the utility. Only then can I re-enable the ethernet adapter for internet access. Then, inevitably, the connection dies within 15 minutes and I have to repeat the whole process.
Can anyone tell me what's going on here? Is the wired network interfering with the wireless network? Is something configured wrong? Below is the output from ipconfig/all, if that helps. The AX is configured with a 169.254 range. IP address and behaves the same way whether the IP address is auto or manual, and there is no difference if the signal roams channels or is fixed to a single channel (I've played with them all).
Thanks in advance for your help.
Wireless LAN adapter Wireless Network Connection:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : DW1501 Wireless-N WLAN Half-Mini Card
   Physical Address. . . . . . . . . : 68-A3-C4-0C-CE-5B
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 10.0.1.2(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Thursday, December 06, 2012 2:32:22 PM
   Lease Expires . . . . . . . . . . : Friday, December 07, 2012 2:41:43 PM
   Default Gateway . . . . . . . . . : 10.0.1.1
   DHCP Server . . . . . . . . . . . : 10.0.1.1
   DNS Servers . . . . . . . . . . . : 10.0.1.1
   NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Local Area Connection:
   Connection-specific DNS Suffix . : XXX.com
   Description . . . . . . . . . . . : Intel(R) 82577LM Gigabit Network Connecti
on
   Physical Address. . . . . . . . . : 5C-26-0A-40-37-A9
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 3.197.129.227(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.254.0
   Lease Obtained. . . . . . . . . . : Thursday, December 06, 2012 2:42:43 PM
   Lease Expires . . . . . . . . . . : Thursday, December 13, 2012 2:42:42 PM
   Default Gateway . . . . . . . . . : 3.197.128.1
   DHCP Server . . . . . . . . . . . : 3.156.134.20
   DNS Servers . . . . . . . . . . . : 3.156.130.30
3.156.130.130
3.23.190.40
                                       3.23.192.43
   Primary WINS Server . . . . . . . : 3.156.130.30
   Secondary WINS Server . . . . . . : 3.156.130.130
   NetBIOS over Tcpip. . . . . . . . : Enabled

Here goes - read this through completely and see if it makes sense:
1. Reset the Express to factory settings by unplugging it and plugging it back in while holding in the reset button - release the button when the light starts blinking - then wait for the light to blink slowly indicating factory default.
2. Disable the wireless and enable the ethernet on the laptop and connect an ethernet cable to the WAN port (the circle of dots) of the Express and use the AU toset it up in bridge mode to create a wireless network with a name of your choice - you don't really need a password but you can assign one if you wish - if you do not use a password you will have to choose to ignore the error message for no security.
3. Accept all other defaults and ignore any messages about not having an internet or ethernet connection and update or finish the setup - if you get a blinking amber light, open the AU and correct any error messages.
4. You can now disconnect the ethernet cable and disable the ethernet on the laptop and enable the wireless so you can stream iTunes to the Express - the laptop must stay wireless to do this - you can not accesss both at the same time - you can also use an iPhone or iPad or iPod to use Airplay and then you can use the laptop via ethernet for the internet.
5. To access the Express from now on, you have to use the AU wirelessly from the laptop.
The above is assuming that you don't currently have wireless in your office - the other alternatives are:
1. To hardwire the Express and have it create a wireless network and access the internet - you could then use your laptop wirelessly or wired to connect to the Express and use Airplay and your pc at the same time.
2. If your office has wireless, you can set up the Express to "join" the existing network - you can then do the same as in number 1.
I hope this helps - everyone's situation is different - the above scenarios work for me - you might have to do some tweaks but the info is there - let me know if you have any questions.

New Airport Express - interfering with home wireless network?

I have an IMac and laptop PC both connected to a wireless home network. I plugged in the new Airport Express, and ran a Toslink cable to my home stereo. My intent is to stream music from the IMac.
When I plug in the AExp I get a flashing amber, then the green light, then flashing amber. I asked the AExp to "join" my network. Soon after the first green light the home wireless connection is unavailable to both my IMac and PC laptop. If I unplug the AExp then the laptop PC reconnects to the network. With the AExp unplugged I also must have "Turn On AirPort" on the IMac to have the internet status as "connected".
Basic problem: when I plug in the AExp both home computers disconnect from the home wireless network.
Any suggestions to getting the AExp to work within the home wireless network?

First, perform a "factory default" reset on the 802.11n AirPort Express Base Station (AXn) to get it back to its "out-of-the-box" configuration.
Then take a look at the following steps to be sure that nothing was missed:
AirPort Express Base Station (AX) - iTunes Setup
Either connect to the AX's wireless network or connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility in "Manual Setup" mode, make the following changes:
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless tab
Wireless Mode: Join a wireless network
Network Name: <existing wireless network name>
Wireless Security: <select the encryption type of the existing wireless network>
Wireless Password: <enter the existing wireless network password>
AirPort Utility > Select the AX > Manual Setup > Music
Enable AirTunes (checked)
iTunes Speaker Name: <enter the desired speaker name>
iTunes Speaker Password: (optional)
Verify Password: (optional)
Click Update to write the new settings ot the AX

Airport Express connection with my wireless network

Hi
I have tried to install my Airport Express, which was okay, but doing so I had to disconnect my wireless network.
What I would like to do is to connect the airport express to the wireless network (Linksys-router). I tried to choose the "Join an existing wireless network" in the admin utility, but now I have lost contact with my airport express base station.
Please help me....
BR Morten
IBM Thinkpad T43 Windows XP Pro

What I would like to do is to connect the airport express to the wireless network (Linksys-router).
What are you trying to do with the AirPort Express Base Station (AX)? Use it for streaming iTunes and/or share a USB printer, or extend your existing Linksys wireless network?

Airport Express simultaneously with another Wireless Network

Hi Folks:
I've had quite amazing success posting questions on here before, so lets see how we do this time. Thanks in advance for any help!
I'm working in a space right now where they have a fantastic Wireless Network. Its a D-Link wireless access point that they use, and I am totally satisfied on their network.
However, I need to be able to print wirelessly via my Airport Express.
Is there a way for me to connect to the Wireless LAN and print to the Express without logging off of one network and switching to the other?
Thanks!
Gary

But - you CANNOT connect your PC to the Airport Express via ethernet. Period. It's been hamstrung.
All you can do in client mode is play some music, and print. And of course, complain like a raving fool out here on the forums that Apple would even think of doing this.
This is tantamount to purchasing an external hard drive, but having the USB port disabled when the disk is turned on. Jezz...

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

I would suggest that you connect the Pioneer to the AirPort Express Base Station using an optical digital audio cable that has a TOSlink connector on one end and a 3.5 mm optical connector (Mini Plug) on the other. You can then connect the Mini Plug end into the AirPort's audio port and the TOSlink end into one of the Pioneer's optical digital audio ports.

Airport Express won't extend wireless network

I think due to a fault my airport express wont extend my wireless network around my house , but it will allow for airplay ... is it possiple to extend my network using the express but with an eithernet cable rather than the wireless that is transmitted out of the express unit ??

Is the other wireless router, that you are trying to extend, another AirPort or Time Capsule base station? If so, are both units 802.11n models? Finally, what is the rough distance between the units and are they located in the same room, different room, or different floor?

Using Airport Express to extend my wireless network

I recently purchased a Time Capsule but found that I could not see the wireless signal from my bedroom. To solve this I purchased an Airport Express to extend the range. I plugged the AE into an outlet in my bed room and set it up to join my existing network. Everything looked fine from the point of view of the Airport Utility. Unfortunately my iPod Touch still can not see my wireless network from my bedroom. I new iPad can see it but the signal is very weak, even when I hold it right next to the AE. Is there a setting I missed?

Rick, welcome to the discussion area!
I plugged the AE into an outlet in my bed room and set it up to join my existing network.
You need to configure the AirPort Express to "Extend a wireless network". The AX does not provide any additional wireless coverage when it is set to "join".
First, you need to check a setting on your Time Capsule as follows:
AirPort Utility > Manual Setup > Wireless tab (below the icons)
Make sure there is a check mark next to "Allow this network to be extended"
Update to save any changes
On the AirPort Express move it close to the Time Capsule for configuration:
AirPort Utility > Manual Setup > Wireless tab
Wireless Mode = Extend a wireless network" (Hold down the option key on your Mac if you do not see this choice appear when you click the selection box).
Wireless Network Name = Same name as your Time Capsule Network
Check mark next to "Allow wireless clients"
Security = Same setting as your Time Capsule
Password = Same password as your Time Capsule
Confirm Password
Update to save settings
The AirPort Express can only "extend" what it "receives". Most users position it too far away from the main router and consequently, the Express extends a weak signal. Try a location that is about 1/2 to 2/3 the distance between the Time Capsule and the area that needs move coverage. Then experiment a bit to find the best signal.
Post back on your results.

Airport express failing to extend wireless network

Have got an airport extreme connected via ethernet to my Virgin Media hub (hub is in modem mode). Also have an airport express to extend the wireless network. Setup has been working perfectly for over a year, then this weekend, literally no settings have been changed, and airport express is giving me a status message of "This airport base station was unable to extend the wireless network. Make sure the wireless network you're trying to extend was setup and is working correctly, that you entered a matching wireless network password into this device and that this device is in range of the wireless network"
I have reset to factory settings 3 times now and whilst it goes through the initial setup, i always get the same status message. Front light is green.
The express version I'm using is the 2012 redesigned version, looks like a white Apple TV and it has the latest firmware. I've tried configuring via my MBA, windows desktop pc (windows 7) and ipad, nothing works
Any ideas?

You have to think of the Express devices as matching pairs when you have one set up to create a wireless and the other to extend it. Here, I assume that you still have the extending Express set up to extend the network.
Power off both AirPort Express devices. The power down order does not matter.
Wait a minute
Power up the main AirPort Express.....the one directly connected to the Virgin hub....and let it run a full minute
Then, power up the extending Express
Check the network and report on your results

Can I use my airport express to extend a wireless network with a non-apple router?

I have been trying to extend my wireless network in my house. Right now I have a dsl modem/router provided by Century Link and an older AirPort express (not sure how old but it uses AirPort utility v5.6). I want to be able to share my printer and use AirTunes. Currently I have the AirPort plugged into the router and setup to create a new wireless network. I would like to combine them so I don't have to switch between to print and play music. I am not really sure where to start or if it even possible. Any info would be great!

If you keep the Express connected using Ethernet and configure the Express to "Create a wireless network" using exactly the same wireless network name, exact same wireless security and same wireless password as the Century Link network.....everything will behave as one "big" network, and you will have additional wireless coverage near the Express.
If you do not need extra wireless coverage, you can turn off the wireless on the Express.
The Express must be in Bridge Mode.
Most users know the name of their wireless network and password, so the really tricky part of doing this is that you must know exactly what type of wireless security settings the Century Link router is using....and then match up the same settings on the AirPort Express.
If the settings do not match up exactly, then you wind up with two separate networks that will each require their own log on.
If you can check the setting for wireless security on the Century Link router and provide that information to us, we can tell you how to set things up the way that you would like.

Will airport express work with 3G wirelessly without access to Y Fi connection ? (usinmg an iPad )

I do not have wi Fi at work. Will airport express work with just the 3G on my Ipad2?

In addition to Keith's comments, if you are asking if the iPad can configure an Apple router like the AirPort Express, the answer would be yes, if you download and install AirPort Utility from the App Store. It's free.
I'm assuming that you have a newer version of the Express. Check the Model No on the side of the device. It needs to be A1264.
http://itunes.apple.com/us/app/airport-utility/id427276530
if you do not have an Ethernet Internet connection to connect to the Ethernet port on the Express, you can still use the Express to "Create a wireless network", but of course devices will not be able to connect to the Internet. The Express will complain, but you can ignore the error messages.
If your printer is wireless, hopefully it is an AirPrint compatible printer. Then you would be able to print from the iPad. Check this Apple Support document for information about compatible printers. There might be other applications that would allow this as well. Check Keith's post for that info.
http://support.apple.com/kb/HT4356
I'm still not clear on exactly what you are trying to do, and devices that you have, so if you can state your goals again....we can make sure that we are not missing something.

Airport express can't extend wireless network

Airport express(A1264) can't extend wireless network. It seems that Airport express can't find my home Wi-Fi network. Amber light is blinking, and AirPort Utility of MacBook also can't find Airport express.
If AE is connected with TC via LAN cable, amber light is blinking with message "Wireless Network" (This Airport base station is set up to join a specific wireless network that can't be found...)
It was successful only once, but all failed after that.
Is there solution for this problem?
[My system]
Time capsule 4th generation
Airport express 1st generation (A1264)
[Settings]
Time capsule (ethernet connected)
- Create a wireless network
- 802.11a/n - 802.11b/g/n (Automatic)
- 2.4GHz / 5GHz Channel (Autmatic)
- WPA2 Personal
Airport express
- Extend a wireless network
- WPA2 Personal
- 2.4GHz Wi-Fi network name and Password is set up

If AE is connected with TC via LAN cable, amber light is blinking with message "Wireless Network" (This Airport base station is set up to join a specific wireless network that can't be found...)
Sorry, I misunderstood what you wanted to do.
Since you did tell us that you had the Express connected with an Ethernet cable, I assumed that was how you wanted to configure the Express.
But I want to extend a wireless network (not using ethernet)
Because Airport Express and Time Capsule cannot be connect via ethernet cable.
Follow the same setup as above....and do not connect an Ethernet cable.
Keep the Express near the Time Capsule for the setup. Once you have a green light, move the Express to a point that is about half way between the Time Capsule and area that needs more wireless coverage.
If you reset the Express several times and try the setup several times without success, I think you have to suspect a defective Express.

Adding Airport Express to D-Link wireless network

We have a D-Link wireless router given us by our ISP. I have an Xbox 360. I'd like to take one of our Airport Expresses, and connect the 360 via Ethernet cable to the Airport Express, while the Airport Express joins the D-Link's network, thus giving my 360 wireless internet.
We used to accomplish this using another Airport Express instead of the D-Link, but for our own reasons, we now need to use the D-Link.
Is there a way to add the Express to the network for this purpose?

"Is there a way to add the Express to the network for this purpose?"
Yes, configure the Express to "Join" the wireless network created by the D-Link and check the "enable ethernet clients" box. Post back if you need step by step on this configuration.
It's possible that this may work OK for you if you have a strong, fast wireless network. But, you may also want to consider that this would be quite a way down on the list of most desirable ways to connect the 360 to your network.
For the best video quality, suggested in order of preference:
Ethernet cable from one of the LAN ports on your router to the 360
Ethernet powerline adapter at the router end and another adapter at the 360 end
Wireless from your D-Link to the 360's wireless-if it will accept a wireless connection
Wireless from your D-Link to the Express. Ethernet from the Express to the 360
Would be interested in your feedback on your experience if you use the Express.

Airport Express wouldn't extend wireless network

Am posting this in case it helps someone else. I have an Airport Extreme set up as a base station and couldn't get an Airport Express to "extend wireless network". I finally found a checkbox in the "Wireless" tab of the "Manually Configure" dialog box for the Extreme that says: "Allow this network to be extended". I could not find this referenced anywhere in Apple documentation, so you have to know to go and check this box. Apologies to the techies if this is a no-brainer, but I only found it by accident. Apple should include a brief paragraph in their wireless troubleshooting guide on extending your network.

When you configure the Express to "join a wireless network" it becomes part of the network so that you can stream AirTunes to the device or use a remote printer connected to the USB port, but it does not provide any additional wireless coverage in this type of configuration.
"Extend a wireless network" does the same thing as above, except the Express will also provide more wireless coverage in the area where it is located.

Airport Express joining Linksys WRT54G Wireless network

I have spent hours trying all different ways of getting my Airport Express to join my Linksys network. And then I discovered that I have to *__remove the spaces from my WPA password__* in order for my AX to join the network. My iMac and MacBook all join the network with spaces in the password, but for some reason the AX does not.
This may be superstition, but I also made sure the pass phrase was all uppercase and exactly 13 characters. Don't know if that makes a difference, but I was tired of trying different things.
Hope this helps some one.

I have spent hours trying all different ways of getting my Airport Express to join my Linksys network. And then I discovered that I have to *__remove the spaces from my WPA password__* in order for my AX to join the network. My iMac and MacBook all join the network with spaces in the password, but for some reason the AX does not.
This may be superstition, but I also made sure the pass phrase was all uppercase and exactly 13 characters. Don't know if that makes a difference, but I was tired of trying different things.
Hope this helps some one.

Airport Express Conflicts with Clear Wireless Network?

Similar Messages

Maybe you are looking for