Airport Express drops connections

I recently bought an airport express to use for streaming music. I set it up to join my existing wireless network using DHCP to get an IP address. It works fine for a few minutes to a few hours. Then it drops the connection to the existing wireless network. Streaming doesn't work and I can't ping it. The status light remains green and I am unable to connect to it using airport utility. If I unplug it and plug it back in, it reboots and then works ok for a while. If I connect to the Airport Express using the ethernet port it reboots and then works fine for a while. The behavior has been consistent for 3 days.
My existing wireless network consists of two access points. One is part of the router that Verizon provided with my fios connection and is an Actiontec and is running in mixed b and g modes uing WPA. The other access point is a Linksys WAP54G with a wired ethernet connection to the router. Both access points use the same SSID. (I have two access points to provide adequate signal strenght throughout the entire house.)
Any suggestions?
Tom

Hi, I recently swapped an old N 450 Router to Apple Extreme (5Gen). Initially the signal was very strong and even in first floor Smart TV Netflix loading was almost instantaneous. I have a 50mbps Xfinity Blast. All nice and felt that it was such a good move and justified the cost of the router too. After 2 days, started noticing connection drop outs, IP address conflicts, unable to connect, wifi was connected but no internet. Power recycled it and things seemed okay. again after 2 days, the internet was very slow, dog slow infact to load up regular websites and pages. This time through it was something with the Xfinity modem (Motorola SB6121) which never in 2 years had given me any issues, but recycled it, seems to be marginally better, but the speed ( not the wifi signal) remained very slow. I am a IT person, not specifically Networking, but quite good with systems, configurations etc. Finally eating up my pride called the Apple Support. The guy who responded seemed knowledgeable. He asked me to walk through the set up process, which I said, I have already done it.He asked me how did I set the router up. I had used an iPad with the Apple Utility and since there about 15 devices connected through out the house, I had used the same SSIDs one for 5Ghz and another for 2.4 Ghz. Apparently using the same SSID leads to deterioration in both connectivity and signal strength. I have never heard of this as I have swapped out routers in past 12 years using same SSIDs without any issues. The Support guy told me that this is only with Apple Routers and not with other brands. I have never heard any such thing and trying to google did not get me much information on this. I reached this forum as result. I need answers desperately so that I can decide to return or keep the router. Thanks

Similar Messages

  • Airport Express drops connection after two minutes

    Configuration:
    Airport Express 7.4.1
    iMac running OS X 10.5.6
    Windows XP laptop (Sony)
    Windows Vista Home (Dell)
    Windows XP (Packard Bell DOT.NL netbook)
    All computers are connecting smoothly through the AEX except the Packard Bell netbook. This is using an atheros AR5700EG WiFi adapter. After establishing contact with the AEX all connections will work for 2 minutes. After that, pinging the AEX is not even possible, it seams to have disappeared. XP however tells me that the connection is 100% OK.
    The problem is: this machine works fine with any other WiFi access point like Linksys, Belkin etc, but not with the AEX.
    Tried varying all settings in the AEX, and disabling Wireless Zero Configuration in XP, but nothing will fix the problem.

    Having the same exact problem except my macbook stays connected with no drops. My toshiba laptop drops after a few minutes. the toshiba also has an Atheros wi-fi card. we tried connecting the Toshiba laptop to another AEX router and it did the same thing. AEX is conflicting either with windows vista or ths particular wi-fi card.

  • AirPort Express dropping connection to Printer

    I have a pretty annoying problem...my AirPort Express frequently drops the connection to my printer. I never have any problems with my wireless internet going out, but after a certain amount of time (seemingly random), the printer will no longer be connected. The green light is still lit on the AirPort unit, and my computer still acts like the printer is active and on, but I get a "Printer Status: Error" when trying to print.
    I'm running Windows Vista on a Dell Inspiron, and I'm trying to print to a Epson Stylus Photo R320. Any thoughts? It's getting really old unplugging the AirPort every time I want to print.

    It's an RCA Digital Broadband router. All activity on it seems to be just fine, and I like I said, my internet connection never goes down...it just stops sending things to the printer.

  • AirPort Express Dropping Connection to AirTunes via Ethernet Connection

    I connect to my AirPort Express via ethernet using iTunes and AirTunes. I am using Windows Vista. The device works great for roughly 15 or so minutes, and then seems to loose its connection with iTunes. iTunes continues to play the music, but there is no sound coming out of the audio device connected to the AEx. If I toggle the Computer Speaker/AirPort Express output selection in iTunes it reconnects successfully with my AEx and will work as expected for a period of time, and then will eventually drop the connection (or at least the audio stops) again. I've used my AEx successfully for a couple years now - something over the last few months changed as this behavior is new. I am using the latest firmware and the latest version of iTunes.
    Anybody have any ideas? Are there known software/firmware compatibility issues?

    See http://discussions.apple.com/thread.jspa?threadID=1949393&start=0&tstart=0
    This might be the same problem you are having. There is no fix as of yet.

  • Airport Express Drops Connection Every 3 Minutes

    This has to be an easy fix. Airport Express holds a connection fine when I'm sending music from it, but flashes amber for half a second every three minutes or so. Here is the log file... Is this normal?
    Feb 9 13:19:53 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 13:23:28 5 Disconnected from network.
    Feb 9 13:23:31 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 13:23:33 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 13:27:08 5 Disconnected from network.
    Feb 9 13:27:11 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 13:27:13 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 13:33:48 5 Disconnected from network.
    Feb 9 13:33:51 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 13:33:53 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 13:35:43 5 Disconnected from network.
    Feb 9 13:35:46 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 13:35:48 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 13:42:23 5 Disconnected from network.
    Feb 9 13:42:26 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 13:42:28 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 13:46:03 5 Disconnected from network.
    Feb 9 13:46:06 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 13:46:08 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 13:49:43 5 Disconnected from network.
    Feb 9 13:49:46 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 13:49:48 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 13:53:23 5 Disconnected from network.
    Feb 9 13:53:39 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 13:53:42 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 13:57:18 5 Disconnected from network.
    Feb 9 13:57:21 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 13:57:23 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 14:00:58 5 Disconnected from network.
    Feb 9 14:01:01 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 14:01:03 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 14:04:38 5 Disconnected from network.
    Feb 9 14:04:41 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 14:04:43 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 14:09:23 5 Disconnected from network.
    Feb 9 14:09:26 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 14:09:28 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 14:14:03 5 Clock synchronized to network time server time.apple.com (adjusted -1 seconds).
    Feb 9 14:15:47 5 Disconnected from network.
    Feb 9 14:15:51 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 14:15:53 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 14:19:27 5 Disconnected from network.
    Feb 9 14:19:30 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 14:19:32 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 14:24:42 5 Disconnected from network.
    Feb 9 14:24:45 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 14:24:48 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 14:28:22 5 Disconnected from network.
    Feb 9 14:28:25 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 14:28:28 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 14:32:22 5 Disconnected from network.
    Feb 9 14:32:25 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 14:32:28 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 14:36:02 5 Disconnected from network.
    Feb 9 14:36:05 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 14:36:07 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 14:42:57 5 Disconnected from network.
    Feb 9 14:43:00 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 14:43:02 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 14:47:12 5 Disconnected from network.
    Feb 9 14:47:15 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 14:47:17 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 15:06:42 5 Disconnected from network.
    Feb 9 15:06:45 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 15:06:47 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 15:10:22 5 Disconnected from network.
    Feb 9 15:10:25 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 15:10:28 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 15:14:03 5 Clock synchronized to network time server time.apple.com (adjusted +0 seconds).
    Feb 9 15:15:57 5 Disconnected from network.
    Feb 9 15:16:00 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 15:16:02 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 15:19:37 5 Disconnected from network.
    Feb 9 15:19:41 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 15:19:43 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 15:23:17 5 Disconnected from network.
    Feb 9 15:23:21 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 15:23:23 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 15:26:57 5 Disconnected from network.
    Feb 9 15:27:01 5 Joined BSS 00:1d:73:8e:a9:48
    Feb 9 15:27:03 5 Internet Configuration leased -- host <192.168.11.2/255.255.255.0> gateway <192.168.11.1> dns <192.168.11.1> wins lease <86400> domain
    Feb 9 15:31:12 5 Disconnected from network.
    Feb 9 15:31:16 5 Joined BSS 00:1d:73:8e:a9:48

    If your AirPort Express is configured as a "bridge", with Connection Sharing = Off (Bridge Mode) it is receiving DHCP services from the router that is ahead of it, in this case, probably the Buffalo that you mention. That would be the device where the lease settings would be adjusted.
    Check AirPort Utility
    Manual Setup
    Click Internet icon
    Check the Connection Sharing setting at the bottom of the page to confirm your setting for the the AirPort Express

  • Airport Express dropping connections while streaming music

    Airport Express once conected to my existing wifi network is not streaming music correctly, instead is dropping without a continuous play.
    Green light is always on.
    Please help

    And your reminder of the channels got it fixed. Being out in the country my internet is provided wirelessly (WISP) and  I remembered after your comment that  the tech who installed our receiver dish said that the internet is being broadcast on the 2.5 ghz band on channel 7 and if any issues arise change the channel to a lower number.   Never had an issue till now and updated the channel to 1 and back in business. A big thanks.

  • Airport Express drops connection

    I just bought a new Airport Express 802.11n base station. After setting up the station to automatically join my existing wireless network (Airport Extreme 7.3.1), I am able to stream music via airtunes. Shortly after (roughly one minute) iTunes can no longer locate the speakers and the Airport Express base station does not show up in Airport Utility, even after doing several rescans. The only way I've been able to have Airport Utility pick up the Air Express station again is to do a soft reset. I can't figure out why the AirPort Express station stops working. The light on it never changes from green, even when it suddenly stops showing up. Any help?

    Man, I think I'm kind of glad that I'm not the only one with this type of problem!!
    Right now, I occasionally get disconnected from the 'net, but my network is still online (I can choose it from the drop-down menu). In Airport Admin (4.2), I can't find my AExp ! If I choose my network, without the use of my Express, I don't get full capacity of it, whereas, when my Express is being a doll, I do. Before, the only way I could work it was to hard reset my modem as well as my Express, but even then it was sketchy. Sometimes it'd work and sometimes it wouldn't.
    So far, from reading various posts by users, I've tried renewing my DHCP lease at a shorter frequency (60min, rather than default 4 hrs). I've tried this "interference robustness" thing, which, everytime I restart, the changes aren't saved. Ugh! But I think this time it's stickin. I've also changed every setting dealing with range of the Express vs interference and such.
    It happens most often in the afternoon / evening when I'm at home, so I'm starting to think that it may be these 2.4 GHz phones or whatever. I'm living in an apartment building, it's really a pain to figure out who's got the phones and who doesnt.
    Is there any other ways to configure my 'net so that this doesn't occur again?
    I've found a few other people who have this same issue as mine. If we can spread the word, it'd be great. Honestly, this is getting really annoying for me.
    Thanks for the help in advance.

  • Apple Airport Express - drops wifi connections after a day or two.....??

    Dear Users,
    Can anyone assist me, I have 2 Apple Airport Express recievers and an Apple TV2 connected to my iMac. The Apple TV is connected via ethernet and a gigabit switch via the BT Infinity Router. The 2 Apple Airport Expresses are connected via wiresles to the BT router.
    Everything works fine, music streams perfectly most of the time.
    But after 24-48 hours of being dorment the Router seems to drop the wireless connections to the Apple Airport Expresses, if you reboot the router they connect again immediatley. I have adjusted the router settings to 802.1n, instead of 802.1n/b/g, which seemed to work better for a few days and the connection never dropped and now the problem has started again.
    Frankly its not the end of the world, but it means I have to reboot the router everytime we want to use all zones for music, which when you have a wife that moans that 'my setup is too complicted and has to be rebooted everytime', it would be great to resolve this for once and all.....
    Have a I missed something simple or do I need a new router/Airport Extreme?
    Thanks in advance
    Matt

    The whole idea here is to test by first powering off your "extending" AirPort.
    Then, take a measurement with your laptop at the location of the "extending" AirPort.....to see what quality of signal that it is receiving.  Remember, it can only "extend" the quality of signal that it receives.
    You would want to see a minimum SNR of 25 at the location of your "extending" AirPort Express.  Higher would be better. If it is less than 25, you need to move the "extending" Express closer to the "main" router so that it will receive a better quality signal to extend.
    Once you have a location with a decent SNR of 25 or higher, then power the "extending" Express back up at that location.

  • Airport Express dropping out constantly so I can't print wirelessly

    I have an iMacG5 running OSX 10.3.9. I have a DLink wireless router which creates my wireless network that the iMac connects to. Also, as my printer as at the other end of the room, I have an airport express connected via USB to the printer so I can print wirelessly. Everything worked like a dream for about 12 months. Until recently I had no security on this network and although I was aware this was risky, I was reluctant to change anything because it all worked so well. But my paranoia got the better of me and I changed the DLink to WPA security. Ever since then, the airport express has acted very strangely. The connection dropped and I was required to do a hard reset. I did that and everything worked. I felt so smug that I had worked out a computer issue! Little did I know that as soon as I shut down the system the airport express dropped out again. I have since discovered that I don't actually need to shut down for the thing to drop out. It just does it of its own accord.
    I have contacted AppleCare 3 times and spent a total of about 4 hours on this to date. No luck. They suggested interference. However my airport icon usually shows either 3 or 4 bars and there is no difference when the thing drops out.
    The only thing I have learned is that Airport Express does not have to be reset all the time. In my situation, it is best to just unplug it, let it rest for about 30 seconds and then you should be able to see the thing in the airport admin utility. It does take a while and several rescans in the utility, but eventually it does show up. This at least means I don't have to constantly set it up to join the network.
    In fact, really it is a doddle to print! I don't know why people like to just go File-Print when you can go through the delight of getting out of your chair, unplugging Airport Express, waiting 30 seconds, looking at the dust under the cupboard thinking I really must get that, plugging the airport express back in, watching the light change from green to amber, to flashing amber, wait for it...wait for it...it's not happening....waiting...finally - green!. Back to the computer, go to Finder - Applications - Utilities - Airport Admin Utility, not showing up, rescan, not there, rescan, rescan, rescan, still not there, rescan, oh good, airport express is showing up. Now, go to Printer setup utility, delete the printer that is there, then add printer, select rendezvous, add my hp, OK......now I can hit File - Print.
    Has anyone got any ideas on how I can join the boring legions of people who are oblivious to the joys of printing my way?

    Hi,
    I am currently replying to this as it shows in the iChat Community.
    I have asked the Hosts to move it to Snow Leopard  (you should not lose contact with it through any email links you get)
    I also don't do Wirelss printing so I can't actaully help either.
    10:01 PM      Friday; July 29, 2011
    Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb( 10.6.8)
     Mac OS X (10.6.8),
    "Limit the Logs to the Bits above Binary Images."  No, Seriously

  • Airport Express dropping out

    I am using an airport express to join my network and have connected a network printer to it using and ethernet cable. I have previously used this airport express to connect a windows PC and never had a problem. I recently purchased an iMac to replace the windows PC and no longer need the Airport for the windows PC, so I am now using it for my network printer. The problem is that the Airport now keeps dropping the network. The Yellow light flashes momentarily and then re-connects, and while this is happening my printer is not on-line. The funny thing is that it only happens when the iMac (which is only several feet from the Airport express) is on. If I put the iMac to sleep it works fine. If I reboot the iMac it works again for a while but eventually starts dropping out again. I have tried power-cycling the Airport and printer but to no avail. Any suggestions would be appreciated. Thanks.
    P.S. all software and firmware are up to date for both the iMac, the Airport Express, and my Airport Extreme.

    Welcome to the discussions!
    By close the laptop, do you mean it goes into standby or a sleep mode? Or, are you using a larger monitor, closing the laptop and not using the laptop screen?
    If it's the former, you need to check on the HP to see if there is a "remember this network setting", "stay alive" or something similar so the connection is not lost.
    When you close the lid on the HP, it is probably blocking access to the internal antenna within the laptop. If the top is closed, the only way the radio waves can be seen would through the sides of the laptop.
    Unless you are seeing intermittent drops in the wireless connection when the laptop is open, it sounds like the Express is delivering a constant wireless signal. Download www.istumbler.net to get a good look at the signal strength and noise on your network. The strength indicators on most laptops are not very accurate.

  • How do I use the airport express to connect a remote PC via ethernet cable and access the internet via wireless connection, How do I use the airport express to connect a remote PC via ethernet cable and access the internet via wireless connection

    Trying to connect my xbox to the airport express. Have wireless in home and do not have a ethernet point behind tv/xbox. How do I configure the airport express to connect to my wireless network and then the airport express can use its connection via ethernet to connect the xbox to the internet.

    Is your AirPort Express Base Station (AX) a 802.11n model? If it is, you can reconfigure it as a wireless Ethernet bridge or ProxySTA. This would allow the AX to join another wireless network and have its Ethernet port enabled for wired clients, like the Xbox 360.
    To activate ProxySTA, you must set up the Express to join a wireless network and then enable the Allow Ethernet Clients setting; both settings are located in the Wireless tab of AirPort Utility.

  • Can I use the Airport Express to connect to a Linksys Wireless Network and then use the Ethernet port on the Airport for a wired connection to a device for internet access?  Would I be able to then also use that Ethernet pt to a Ntwk Hub for more wired c

    Thanks for the help.  Looked but not clear on what I am trying to do as being possible.  Can I use an Airport Express to connect wireless to a Linksys Wireless Router, such that I can then use the Ethernet ports on the Airport to either connected to a PC wired, or even use a hub off the Airport Express to allow multiple wired connections to it? 
    I am not looking to have the Airport Express extend my wireless network, just connect to it and provide me wired connections in a different location from where my Linksys Route is located.  Would prefer to replace Linksys with all Apple, but just not possible financially yet.  Thanks for the help.

    If the AirPort Express Base Station (AX) is an 802.11n model, then yes, you can reconfigure it as a wireless Ethernet bridge. In this configuration, the AX would join the wireless network provided by the Linksys router and its Ethernet port would be enabled for either a single wired device or for an Ethernet hub or switch for multiple devices.

  • I can print from my macbook pro using airport express usb connected printer, however my iPad is looking for an airprint printer.  Can I direct the iPad to the usb connected printer.  Both macbook and iPad confirm a wifi connection through the airport exp.

    I can print from my macbook pro using airport express usb connected printer, however my iPad and iphone are looking for an airprint printer.  Can I direct the iPad/iphone to the usb connected printer.  Macbook iphone and iPad confirm a wifi connection through the airport express.

    You will need to install an App like Print Central on the iPad to try to print to the printer. It will allow you to print to most printers. Check with their support folks if you need more info.
    PrintCentral for iPad on the iTunes App Store

  • Do I need to have Airport Express to connect to other computers on our homer network?

    Do I need to have Airport Express to connect to other computers on our homer network?

    Not necessarily. You could use the "Create Network" feature of your MBP's built-in AirPort card to provide an Ad-hoc wireless network for local wireless-capable computers to connect to.

  • Can I use Airport Express to connect to a printer, Time Machine Back up drive, second b/u drive, and scanner through a USB hub? if so, how?

    I have an Airport Express that connects to my printer. I'd like to add a scanner, and two back up drives (one for use with Time Capsule, another specifically for photographs backed up from Adobe Lightroom.
    The printer connects to the Airport Express through a USB hub and is recognized.  I cannot get the scanner nor either of the back up drives to be recognized.  Is there a way to do it or will I need to rely on a USB hub wired to the USB port of the MacBookPro?  If it is possible, can you walk me through the set up for each? 
    Thanks,
    Doug Earle

    I'd like to add a scanner, and two back up drives (one for use with Time Capsule, another specifically for photographs backed up from Adobe Lightroom.
    Unfortunately, the USB port on the AirPort Express will only work with a compatible printer.
    It will not work with a scanner, copier, or hard drive.
    It should be possible to do what you want by connecting a powered USB hub to your Mac and then connecting the devices to the powered hub.
    The setup for the scanner and hard drive would be covered by the manfacturers documentation, so providing specific advice for those types of products would be outside the realm of this support area.
    But, if you can provide model numbers, it is always possible that another user who is using those products might see this post.

Maybe you are looking for

  • What is the best iTunes alternative  for a 4th Generation iPod Touch?

    iTunes is the worst music application I have ever used and would love to be able to use a different application to sync music with. I have a really nice computer, but it is taking 10 times longer to sync music than Windows Media Player. I'm beginning

  • No sound on IPad.

    I have tried everything, it is not the lock rotation thing most people have but the sound comes and goes?? It started around this morning, it happened after I would take a video, and I tried to play it back and there was no sound? If I press the home

  • IPod Video plays w/no audio

    Recently i downloaded videos and saved them to my iTunes. once i converted the video and syced into my iPod, you could not hear the music of that video and not on the iTunes. But the original video did play with audio. How do i get the converted vers

  • JDeveloper + WebLogic: Problem deploying

    Greetings, I'm new to Oracle and JDeveloper and I'm developing an application (webservice) that uses Oracle 11g as database. To develop the webservice I'm using JDeveloper Studio Edition Version 11.1.1.0.1 and WebLogic application server. Everything

  • Shaky handheld footage with Date Stamp: Warp Stabilizer keeps failing.

    I suspect it's because the Date Stamp doesn't move while the camera shakes. WS has failed, despite trying a mix of options. Any advice? Is WS likely to even work when footage is shaky but the Date Stamp isn't?