Airport Express Ethernet

I have an Airport Express and I have used it as a extension from my Airport Extreme. I have brought it into work today to create a wireless signal via an ethernet cable but the light is flashing orange and is sending out no signal. Do I have to re-configure for this connection and if so will it cancel the other operation I have set up on it already? Any info and set up instuctions are appreciated and thanks in advance.

Most likely you will need to reconfigure your AirPort Express Base Station (AX) for the type of network that it is being used with.
The AX can store up to five different configuration profiles.
You will need to use the AirPort Utility, located in Applications/Utilities to create & save these profiles.
To create a new profile:
Open AirPort Utility, select your AX from the list, and then, click "Manual Setup."
From the AirPort Utility menu, select "Base Station," and then "Manage Profiles."
Click "+" to create a new profile; give it a name, and then, click OK.
Set options, such as network name, passwords, Internet connection method, etc.
When done setting the options, click Update.
To switch profiles:
Open the AirPort Utility, select your AX from the list, and then, click "Manual Setup."
From the AirPort Utility menu, select "Base Station," and then "Manage Profiles."
Click on the desired profile, and then, click OK to apply the new profile and restart the AX. Just remember to switch to the desired configuration profile before removing power from the AX.

Similar Messages

Airport Express - Ethernet jack

Hi
Does anyone know if the airport express' ethernet port outputs to devices as well as receives.
Ideally I need to convert my current 802.11n time capsule signal back to a ethernet device (a AV component) that does not have wifi capability.
Is this possible? Could I connect my airport express near the device and connect them up using ethernet - would this connect my device (via ethernet) to my internet signal?
Thanks

If you have the 802.11g AirPort Express (AX), you will need to configure the AX and Time Capsule to wirelessly connect using WDS. In this mode the AX's Ethernet port will be active.
If you have the brand new 802.11n AX you can either use the new 802.11n "extend network" feature OR WDS to wirelessly connect the two.

HT204371 airport express Ethernet port isn't working

why isn't my airport express ethernet port not working????

We will need more information than this.
What generation of Express is it? What OS are you using? Have you tried with multiple cables?

Airport Express Ethernet Port in Client Mode Please

Hi,
I am writing here as I can find anywhere to post feedback on Airport Express. I would really like to see the Ethernet port work in client mode. I am sure not the only one (a search on the net tells me so). If someone from apple could explain why this is not possible, I would be interested so that this subject can be put to rest.
Thanks.

Simple reason - Apple's engineers made a design decision not to support it. Speculation as to the reasons for that decision are not permitted in these forums. Apple won't tell us here either, since their employees don't post to these forums on matters of this nature.
As I suspect you are aware, the ethernet port is active when the Airport Express is configured as a remote base station in a wireless distribution system (WDS).

Airport Express Ethernet port doesn't work.

I bought my airport express little over a year ago, so the new one, and since then the ethernet port stopped working. The only way i can get it to work is by bending the eithernet cable a certain direction and holding it down, other than that it does not recognise there is even a CAT5 cable plugged up to it. Has anyone ever seen this or know what to do to fix it? I do not want to have to buy another.

This should not be much a problem, unless it's...... you guess it:
The WAN Port!
If it is, does changing cables help?
If it really is the port and not the cables, I"d probably try to fix it manually myself, unless it's still under warranty.

Airport Express Ethernet WiFi bridging with 3rd-party wireless base?

I want to use an Airport Express as a substitute for a very-long Ethernet cable. Essentially, I want to connect a device (say, a computer) to the AE using an Ethernet cable, have the AE connect to a base station (not an Apple device) via wireless, and reach the network (Internet) on the other side of the base.
A diagram of the desired goal is at http://img.skitch.com/20091111-1j7a61eka32jqntm217wwg7d3g.jpg
I'm baffled. Here is what I've done:
-Reset the AE to factory defaults
-Connected a laptop to the AE via the Ethernet cable. Turn off my wireless (to make sure I'm talking to the AE via wired connection; this confirms the AE Ethernet port is working.)
-Configured the AE (via the Ethernet cable) in a variety of ways (see below), restarted it.
(alternately)
-Reset the AE to factory defaults
-Connected a laptop to the AE via wireless (connecting to the default-named network the AE creates on factory default reset)
-Configured the AE in a variety of ways, restarted it.
(This essentially suggests the AE is fully functional and not failed; I'm successfully able to connect to and configure the AE after factory default reset either wired, or wirelessly.)
I've tried various configuration attempts, but the one that seems to get closest - but still fails the goal is this:
-On "Airport / Wireless" tab: Join Wireless Network
--(I've entered my SSID for my network in the Wireless Network name field)
--(I've selected WEP 128 for security. I don't think I should be using WDS, given what I've seen elsewhere about WDS only working with an Apple Extreme.)
--(Of course, I've confirmed the passwords match)
-On "Internet / Internet Connection", the "Connect using" dropdown is disabled / greyed. This appears to only be enabled when I select "Participate in a WDS network" in the Wireless tab - which (as I said) I don't think I can use.
-On "Internet / Internet Connection", the Configure IPv4 is set to use DHCP
On restart, the AE successfully starts - it get's its IP address, the FIOS base station sees the device and lists it as online, and I can transmit audio successfully from iTunes to the stereo via the AE.
BUT, configured this way, the Ethernet port is not providing network connectivity to the device attached to the AE via the Ethernet cable -- the same Ethernet cable that was moments ago letting me talk to the AE to configure it is now not active. When I attach my MacBook to this cable and open System Preferences and look at the Ethernet connection, it shows as not even having a cable plugged in; there's no Ethernet link / carrier present. (Until I do a Factory Reset on the AE, after which it works fine again.)
Note: My AE is about 2-3 years old. I initially / previously had this configuration working just fine after I first installed the AE (after much pain, I recall). But I recently had Verizon installed, and in the process they put in a new base station. I seem to not be able to re-create the configuration I had that was working before.
Note 2: I'm attempting to use the wireless base station supplied by Verizon FIOS, which supports a ton of connectivity options - though it doesn't list (and therefore I'm assuming doesn't do) Apple's WDS.
Note 3: When I had it working before, I could have sworn the AE was also acting as a wireless base station that I could see in my available wireless networks listings, and was able to connect to the Internet wirelessly through it - as if it was a repeater of some kind. This isn't crucial; but it could be helpful in diagnosis.
Note 4: I think I may have previously had the AE connecting via another device: I also have a Netgear WG602v2 that was connected BaseRouter---Netgear((( ))) AE---Device (where --- is an Ethernet wire, and ((())) is a wireless link). HOWEVER, I can't be sure this is how it was working; this may have been a relic from attempts to get it working originally several years ago. It is not essential.
What am I missing?

It sounds like you have an older 802.11 b/g AirPort Express, which as Duane mentions will not function as you would like.
The newer AirPort Express 802.11n has a function called ProxySTA which allows the device to join (according to the attached article) virtually any wireless network with an option to "enable ethernet clients".
While it is not possible to know whether any wireless network will be compatible with this feature, it has worked on a 2Wire and Netgear router that I've tried. Haven't tried Verizon Fios, so I can't assure you that this will work as you desire.
http://www.macworld.com/article/132754/2008/03/express11n.html
Another option might be to use a pair of ethernet powerline apapters, providing that everything is on the same master electrical circuit. In general, I've found the adapters to be more reliable and better performing than wireless, but of course, your mileage may vary. Post back if you need more info on this option.

Airport Express Ethernet Port

Ok, I have an Airport Extreme base station, and I was thinking of getting an Airport Express to extend the range of my wireless network. I have been reading on the Airport Express part of the Apple site and it says the Ethernet port can be used to connect to a DSL or Cable modem, or an existing network. I was wondering If I could use it as a way to connect my PS2 to the Internet?
thanks,

1. do a factory default reset of the Airport Express you want to use as the remote base station per:
http://docs.info.apple.com/article.html?artnum=108044
2. run the Airport Setup Assistant on one of your Airport card equipped Macs, and use its guidance to configure the second Airport Express as a new base station that "extends" the existing wireless network created by the Airport Express acting as your main base station.

Airport Express "ethernet unplugged"

My airport express was working fine. Now has blinking yellow light. Airport utility says "ethernet unplugged". I verified that the AE is plugged into a working ethernet cable from my router by unplugging the AE and plugging a laptop into the same cable and verifying that my laptop is then connected.
Tried resetting the AE (by pressing the little recessed button). Reconfigured, but same problem. AE firmware is 6.3. iMac is running Leopard with all SW updates applied. Ideas?

It appears that the communication between the modem and the AirPort Express Base Station (AX) is "broken."
Try the following, in order, until resolved:
1. If the modem has a reset switch, use it to reset the modem. Wait at least 5-10 minutes for the modem to initialize.
2. Remove power from the modem. If it has a backup battery, remove this as well. Wait 5-10 minutes. Replace the battery, and add power back to the modem.
3. Perform a complete power recycle of your network components as follows:
Modem/Router Power Recycling - Quick
o Power-off the modem, AX, & computer(s); Wait at least 5 minutes.
o Power-on the modem; Wait at least 5 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
o Power-off the modem, AX, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
o Power-on the modem; Wait at least 15 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s)
4. Contact your ISP to have them perform a "modem reset."

Airport Express Ethernet Problem

I tried searching for help and couldn't find anything.
I use an airport express as a wireless router attached to a cable modem. I keep loosing my connection to the internet however the indicator light stays green. Unplugging the ethernet cord and plugging it back in fixes it, but this is a pain. I tried a hard reset and it hasn't helped.
Any ideas? Thanks.

Sounds like interference from one of these: Items that can interfere with AirPort
AirPort: Potential sources of interference
Minimizing interference in an AirPort network

Airport express - ethernet cable

Hope you guys may be able to help here. Just moved house and during the build works, we've had 4 cat 5e points done to each room. The basement has an imac with a zepplin in close proximity, both of these have data points within reach. Grd floor living area has my mac book air with a bang & olufsen stereo closeby. What i'm after doing is having the airport express plugged near the B&O, ethernet the airport express to avoid any potential drop off's which our last house suffered, so i'm hopefuly bypassing wifi, and jack pluggin the airport express to the B&O. All worked via wifi before, but will this still work if i use the ethernet only?
I have various steroes around the house and hoping to use the remainder of my airport expreses this way too...unless you guys tell me...Nope, gotta be wifi
Look forward to your comments in due course, kindest regards
M

Worked an absolote dream, top man for the advice, thank you.
I know it's gonna be different thread, b ut chancing my arm and asking, have an B&W Zeppelin airplay, hard wired it via ethernet, but with the firmware upgrade, always reverts to wifi and during the day, music drops off...any thoughts?
Thanks again, M

Airport Express & Ethernet question........

I'm trying to advance my network. The present network consists of of a DSL connection with a a graphite base station, an AE connected to the home stereo for music and a AE connected to a printer. We have another desktop in the room with the AE/pinter and wondering if/how I can use an ethernet from the AE to the desktop to get it connected to the internet.
I've had the network set up with a router to the desktop but needed to move the graphite base to expand the coverage to my deck. Problem is, I've now lost the internet connection to the desktop.
Any help would be great....thanks!!

It is possible using WDS, however not in your current network configuration.
One of the Airport Express units would need to be connected direct to the DSL connection (instead of the Graphite).
iFelix

Airport Express Ethernet to WLAN

I want to connect a Express to a white Extreme Base station (which has Internet access to cable modem) via Ethernet in order to bring WLAN service into another room (configurating both as a WDS network does not work, as between both stations due to distance and walls a wireless connection is not reliable.) (This kind of WDS combination works with another Extreme in another more close room)
I made the setup with Airport Admin app. This one leaves the Wireless mode of the Express to OFF.
what does that mean:
A) only the wireless interconnection "backwards" to the Extreme is off (because Ethernet does this job to connect both?)
B) or the whole wireless service of Extreme is off?
if B is answered with YES, what is the correct setup for my purpose?
Message was edited by: Urs Gruetzner

I want to connect a Express to a white Extreme Base station (which has Internet access to cable modem) via Ethernet in order to bring WLAN service into another room...
Then you do not want to disable the wireless portion of the AirPort Express (AX).
To make this work you simply configure the AX to
operate as a bridge (not sharing a single IP address).
use the same wireless SSID (Network Name) as the AirPort Extreme base station (AEBS).
use the same wireless encryption type/level/password as the AEBS.
use a different channel as far from the one used by the AEBS as possible.

Confusion with AEBS, Airport Express & Ethernet

I have an Airport Extreme Base Station (AEBS) in one room and an Airport Express (AX) in other. The AX is set to extend the wireless network.
The AEBS is right by my desktop machine so I have opted to connect to the AEBS by way of an ethernet cable. When I went this route I turned the Airport off on my MacPro. When I got the AX I couldn't see the device in my Airport Utility until I turned the Airport on. My quesiton is by leaving the Airport on in Airport utility and having the ethernet connected is my MacPro connecting via wireless or directly by way of the ethernet cable? If I turn the airport off in the Airport utility then does that turn off the wireless or does it just think I want to turn wireless off on my machine?
In theory it may not matter but I have a gigabit ethernet switch that I use so I can also connect a NAS drive and a windows PC (for work) into. I just like to know how I connect.

jessie wrote:
My question is by leaving the Airport on in Airport utility and having the ethernet connected is my MacPro connecting via wireless or directly by way of the ethernet cable?
Both, it turns out. In the "Info" tab of Network Utility you'll see that both your Ethernet port (en0) and your AirPort connection (en1) have an IP address and network traffic.
If I turn the airport off in the Airport utility then does that turn off the wireless or does it just think I want to turn wireless off on my machine?
Don't confuse (a) using the AirPort menu bar item to "Turn AirPort Off", which just disables the AirPort circuitry of your Mac and (b) using AirPort utility to disable the AirPort functionality of your AirPort base station, which reduces the base station to an Ethernet router.

Airport Express ethernet port question

I have an airport extreme base station already, but it struggles to reach my home office from the living room (where the cable connection comes into the house).
Also, my wife's PC doesn't do 802.11n, so I have to run the wireless network in backwards-compatibility mode.
If I buy an Airport Express to extend the network, can I plug my wife's PC into the ethernet socket, or is that port only for WAN connections?

If I buy an Airport Express to extend the network, can I plug my wife's PC into the ethernet socket, or is that port only for WAN connections?
Yes. If the AirPort Express Base Station (AX) is configured as either a relay/remote base station in a WDS with your Airport Extreme Base Station (AEBS), its Ethernet port will be enabled for network (& Internet) access.

Airport Express Ethernet Port for XBOX

Please could somebody help me!!!
I have the new Airport Extreme in my home office running an 80211n network. It is also connected by one of its ethernet ports to my first airport express providing my home with an 80211g network for our older powerbooks.
I have a second Airport Express in my living room which is plugged into my Sony Receiver for use with airtunes.
Question - we have just got an XBOX. It is located in the living room next to the second Airport Express. I want to plug the xbox into the LAN port on the airport express so that the XBOX can access the internet. Please could somebody explain how I do this. (I do not have the wireless adapter for the XBOX).
Many thanks!

Thanks for the help. I followed your directions and the info in the linked page. Everything appeared to configure correctly. However, the xbox still does not get a connection. The xbox is connected to the 2nd AX using an ethernet cable. Am I meant to somehow tell this AX to allow its single WAN port to act as a LAN port? Or is this meant to be automatic? Also, do I need to set this AX to distribute IPs... or will the 1st AX do that? In other words how does the xbox get an IP. Any other ideas???
I am really grateful for any help you can offer...

Airport Express Ethernet

Similar Messages

Maybe you are looking for