Airport Express extending network needs to be restarted daily

I'm having a really annoying problem with my Airport network. Here's the configuration:
Den: Latest generation simultaneous Dual-Band Airport Extreme
Living Room: older 802.11g Airport Express used only for AirPlay
Office: older 802.11n Airport Express wired to the Airport Extreme via ethernet, extending network
Hallway: 802.11n Airport Express wirelessly joining and extending network
Bedroom: Latest generation simultaneous Dual-Band Airport Express wirelessly joining and extending network
I have an older house which is not terribly big but the radio-opaque walls make it difficult to propogate wireless, thus the need for so many units.
It all works pretty well except for my bedroom Airport Express (simultaneous Dual-Band). On a daily basis it will lose connection with the network or go so painfull slowly that it's pointless. The only solution is to do a reboot of the unit which works temporarily (good connection / good speeds) My son likes to watch Roku in our bedroom and that Roku uses the WiFi that the Airport Express should provide. Needless to say troubleshooting wifi when your 3 year old is crying because he can't get 30 seconds of streaming before the signal craps out is not fun. Anybody have any suggestions???

"Hard reset" the bedroom Extreme to preclude the possibility that some corrupted internal parameter is limiting its performance. Consider doing that with all of them. They will subsequently need to be reconfigured.
Configure the den Extreme to provide a unique name for its 5 GHz network, and ensure all the devices capable of using it are using it, and not 2.4 GHz. Find out what your Roku is capable of using.
The key to solving problems, if your challenging requirements are solvable, is to start with as simple an installation as possible, then progressively add to it. Find out the maximum usable range of your den's Extreme in both 2.4 and 5 GHz bands, then position any devices used to "wirelessly extend" its signal roughly half the distance to that Extreme - not a different base station. The ideal location for the Roku's Express may not necessarily be in the bedroom.
Run speed tests each time and make sure you are not trying to "extend" a weak signal. "Extending" a weak signal makes it stronger, but no faster that what it receives.
That's all you can do.
... I thought "N" networks minimized that problem.
You're right about that.
The thing is I get decent wireless reception in the bedroom WITHOUT the express plugged in.
I wonder if those devices are really using the Express you think they are. That's the problem with multiple base stations. There are ways of addressing this question but not with the current AirPort Utility version.

Similar Messages

  • Iphone will not connect to airport express extended network - macbook and ipad will - Help

    Iphone will not connect to airport express extended network - macbook and ipad will without problems.
    iphone will connect to base station no problems, I've restored settings and started again but still the same, the iphone picked up the network for the last couple of months, but not now ?

    I'm having the same issue. My AExpress used to give a good signal strength on the far side of the house extending he network created by my Extreme. However, I've noticed lately that my iPhone does not receive the same strong signal it once did. AE has a green light, I've rebooted it, and my Extreme but there is no change in signal strength. Other than the green light, how can I tell if the Express is working if I don't get a good network signal?

  • Time Capsule & Airport Express Extended Network loses connection!

    OK, so I am an Apple virgin of 2 months experience, after many many years with Windows based PCs, so please be patient and gentle with me. Sorry about the long explanation.....
    My set-up comprises of a Time Capsule, which is connected to the Internet via a NetGear ASDL modem. Both pieces of equipment are situated in my wife's office on the first floor of our house. My office is on the ground floor, where I have a 27" iMac and an Airport Express which is connected to a printer via the USB port. The Airport Express is sited about 10 feet from the iMac.
    All software and firmware are lastest versions - TC v7.5, AX v7.4.2 & Airport Utility v5.5.
    For the past 2 months, I have only been using the AX to print wirelessly and the set-up has worked faultlessly.
    Earlier this week, I decided change the configuration to extend the network to allow me to use my laptop & iPhone in areas of the ground floor where I had no signal. I followed the online instructions and first changed the TC to check the box to 'allow this network to be extended', after updating the configuration successfully I moved to the AX. Here I changed the wireless mode to 'Extend a wireless network', selected the network name and checked the 'Allow wireless clients' box. This also updated successfully.
    Everything ran correctly and the range of the network was greatly increased.......great, job done...not!
    After about 3 hours the iMac lost the connection and the TC disappeared from the Airport Utility pane and refused to reappear. I checked but also couldn't connect or see any network on the laptop or iPhone, so have dismissed a fault with the iMac. I finally got things back up after doing a power reset of the TC, but after a few hours same problem occurred, and occurred and occurred. By clicking the Airport Utility icon on the top right of the screen and following the prompts from 'no Internet connection', I can at least get things up and working without a power reset of the TC, but the connection still drops after 2-5 hours each time.
    My first call to Apple Support led to a full reset and re-config of both the TC and AX, setting the extended network up as I had done originally. The only difference was an iMac reset (alt/cmd P&R on power up) and changing the 2.4Ghz channel from 1 to 11. This had no affect and the connection drop-out problem continued.
    My second call to Apple Support led to me being passed to a Level 2 Techie, who first suggested that I tried disabling the Guest Network - tried it, and it made no difference. I was then told to try a WDS network, which whilst not losing connection, is slower and has less range than the original extended network and frankly sounds a cop-out.
    Has anyone had a similar problem, anyone solved the problems, can anyone offer any help or advice please.. I'd appreciate any input....thanks.

    Similar problem here. Cable Modem (Moto SB6120)->AEBS (802.11n dual-band)>AX (802.11n) for wireless connection to MacBook Pro running Mac OS X 10.6.2. AEBS configured as dual-band: 801.11a/n at 5GHZ and 801.11b/g/n at 2.4 GHZ. AX configured to wirelessly extend the AEBS 5GHz 802.11a/n network. I am able to run on the extended 5GHz network (via AX) for varying lengths of time, until the internet connection dies. When this occurs, I am able to switch over to the 2.4GHz network to get back online. Solution up until now has been to unplug the AX, then plug it back in. After the AX restarts, I am able to hop back onto its 5GHz signal and get to the internet. However, the internet connection on this band will drop again after some time.
    I was on the phone with Apple Support twice in the past week to get this resolved, but no joy. Senior Advisor seemed to think that my AX was working properly, and that that the problem could be with my AEBS -- perhaps the 5GHz antenna might be bad in my AEBS? Seems odd to me, since both my AEBS and AX are less than 2 months old...
    I just read the post from LocoDoc and decided to see if I could replicate the problem. Sure enough, when I am connected to the internet via my AX extended 5GHz network signal and a Time Machine backup starts, the internet connection quits. Only recourse is to restart the AX. Note that I do not experience this problem with Time Machine while connected wirelessly straight to the AEBS 5GHz signal. Only when I am connected to the "extended" signal via the AX.

  • HT4259 Does Airport Express extended network inherits wifi time restrictions?

    Hello:
    I have created a network with my Airport Extreme and I've set up some wifi access time restrictions based on mac addresses. Now I want to extend this network adding an Airport Express at the living room. Everything went smooth but I'd like to know if I need to set up the restrictions at the Express or does it inherit them from the Extreme.
    Thanks!

    Inherits from the Extreme as they are determined by the connected devices to the Wi-Fi.

  • Multiple AirPort Express - Extending Networks

    Hello
    I have been at it all morning trying to get it to work, no luck thus far.
    The network I have at the moment consists of
    Adsl modem > (cat5) Airport Extreme > (wirelessly extended by) Airport Express 1F > (wirelessly extended by) Airport Express 2F
    I am running this network in a 3 storey building
    Ground floor - Airport Extreme
    First floor - Airport Express 1F
    Second floor - Airport Express 2F
    The Express on the first floor picks up the network created by the Extreme on ground floor and successfully extends it to the second floor.
    This is the part that is giving me a world of trouble.
    The Express on the Second floor picks up the network being extended by the Express on the First floor, but fails to extend it.
    The green light is on and everything, settings are correct (identical to 1F).
    Though when I am on the second floor and start to venture away from the limits of 1F, the 2F doesn't seem to boost the signal or extend the network, after walking 5 meters away I lose connection to the network.
    Can anyone help?

    As I have 3 Airport Express' all up, would I theoretically set it up so that 2F would "Join a wireless network" > allow ethernet clients then plug the third Express (3F) to 2F. Then setting 3F up to create a wireless network? clients would have to reconnect between the two, but it would be a temporary fix until I can have a network cable installed to connect the Extreme with 2F.
    You could leave AirPort Express 2F in the "extend a wireless network" configuration because the ethernet port is enabled in this type of setup.
    Then connect an ethernet cable to 3F from 2F and configure 3F as a "bridge" (Connection Sharing = Off (Bridge Mode)) to "create a wireless network" using the exact same wireless network name, security and password as the main router. Then, computers would not have to reconnect as they move around the house.
    If you configured the network this way, you would not need to connect AirPort Express 3F all the way back to the AirPort Extreme. But, you would have better bandwidth if you did connect it directly to the AirPort Extreme.
    Message was edited by: Bob Timmons

  • IPhone 5 won't connect to Airport Express extended network

    I've just bought a new Airport Express and have succesfully set it up to extend my exisiting network through the Time Capsule. Now when I'm in the area where i need to connect my iPhone 5 to the new airport express, I'm not seeing it in my wifi settings on the iPhone. My understanding was, the express would create a an extended wifi area that any device could connect to. Is this correct?

    It should but you probably have it in the wrong mode.. it is joining a wireless network not extending.
    Go back to the airport utility and change the setup of the express.. make sure it is extend not join.
    You may need to reset it to factory and start over.

  • AirPort Express - extend network and/or AirTunes - one or both ?

    I would like use my second AE to extend my existing AE network AND wire it to my stereo to use the AirTunes feature. No trouble setting it up for AirTunes but can't seen to get it to extend the network. Any tips about how I can get both features to perform as advertised?

    If you need more wireless coverage, you can use the WDS configuration method for a "mix" of older "b/g" and newer "n" devices.
    The big downsides here are that WDS operates only at "g" wireless, so you lose any faster "n" capability on the network...and...the bandwidth of the entire network will be cut in half. So, in effect you will have a bit more wireless coverage, but it will be a "g" wireless network running at half speed.
    I don't recommend this, but if you want to try, post back for more details.

  • Do I have to use airport extreme to be a main network if I want to use Airport express extend my wifi range

    Do I have to use airport extreme to be a main network if I want to use Airport express extend my wifi range.

    You cannot extend wifi from a different brand router..
    Only apple to apple.
    But the apple router does not have to be the main router.. it can be in bridge.. as long as it is creating a wireless network it will work fine.

  • Airport Express extends 5 Ghz and 2.4 Ghz or just one at a time?

    I recently switched my dual band Time Capsule to use different names for the 5 Ghz and 2.4 Ghz networks.
    Will the Airport Express extend both or just one at a time, if so, which one will it extend?
    I have two Airport Express modules, bought a long time apart, is there any difference in functionality and how do I tell them apart if this is the case?
    All are running the most recent firmware version.

    Welcome to the discussion area, Mike!
    Will the Airport Express extend both or just one at a time, if so, which one will it extend?
    The AirPort Express is a single band device, so it can extend either the 2.4 GHz or 5 GHz band, +but not both at the same time+. Since you have different names for the 5 GHz and 2.4 GHz bands, the Express will extend the 2.4 GHz band by default. Using AirPort Utility, the setup application for the AirPorts, it is possible to configure the AirPort Express to extend either band.
    If you are perhaps thinking of extending the 5 GHz band, this can be a bit tricky because 5 GHZ signals do not travel effectively over distance or penetrate obstructions as well as 2.4 GHz signals. You almost have to have a line-of-sight relationship between the Time Capsule and the AirPort Express to be able to extend the 5 GHz band.
    I have two Airport Express modules, bought a long time apart, is there any difference in functionality and how do I tell them apart if this is the case?
    Look on the side of the AirPort Express for the model number in the small print. You'll need Model No A 1264 to be able to "extend". If you have the older Model No A 1084, that version will not be able to "extend" a wireless network, but you could use it to "join" the wireless network and stream AirTunes to the device.
    All are running the most recent firmware version.
    That would be 7.5.2. If you have the older version of the AirPort Express, the latest firmware version for that device would be 6.3.
    Message was edited by: Bob Timmons

  • Airport express extending - n AND g

    I have an airport express extending a dual band airport extreme network. The extreme has one band on n (for laptops) and one band on a/g (for iphones and an older laptop).  The airport express extends the network, connecting wirelessly to the extreme in another room, and sharing its connection with an iphone and an old laptop.
    My question is this: will the airport express connect with the airport extreme (receiving its internet connection) at n speeds, but then connect with my iphone and old laptop (sharing its internet) at a/g speeds?  I know the express is not dual band and thus cannot share its connection on different bands, but can it connect on a different band than it shares?
    Thanks!

    From what I've tried the Airport Express will only extend as it connects to. I've tried and it doesn't seem to "auto-convert" from one to another.
    Also, you might want to look at the 802.11n 5ghz and 802.11n b/g/n 2.4ghz. Set this in your Airport Extreme accordingly (which you already might have), and let Airport Express automatically extend the 802.11n b/g/n 2.4ghz. This way, the iPhone will connect as fast as it can and the older laptop can connect.
    BTW here is my "poor man's dual band" setup if anyone's interested:
    DSL modem is connected to Netcomm 802.11b/g/n wireless router. This supplies the 802.11b/g/ 2.4ghz N signal for iPhone, Xbox360, and anything else.
    Then, I connect via ethernet from Netcomm wireless router to my existing Airport Express. Airport Express supplies a pure 802.11 5ghz N signal for my Mac, iPad2, new iPad and AppleTV.
    This way, the Mac, iPads and AppleTV always "see" only the Airport Express network, hence WiFi iTunes syncing as well as AirPlay streaming is great, and the 5ghz network with maximum N speed doesn't suffer interference and/or dropouts such as when my microwave is running.
    As for the iPhone, I'll just use a cable when I need to, but this way my iPhone and Xbox360 can access the Internet as needed without degrading the connectivity of the Mac, iPads and AppleTV. I don't play online games, I only need connectivity to update or download stuff on Xbox360.
    Yes, the disadvantage is double-NAT, but I haven't encountered issues yet.

  • Airport Express Extends 5GHz at 2.4GHz?

    My second generation(802.11n) Airport Express extends my 5GHz network, Net5, at 2.4 GHz. The express is about 20
    feet from its "target," an iPad 3 serving as an internet radio. I know this because a scan turned up the 5GHz network on the same
    channel as the 2.4GHz one and identified as "Net5."
    As far as I can tell, all my settings are correct, etc. I'd be grateful for any ideas, comments, etc.

    Ok, thanks for clarifying that for me. By default, the 2nd generation Express should extend both radios of your 5th generation Extreme. The key is placement. As you are already aware the range of the 2.4 Ghz band is greater than that of the 5 GHz one.
    Even if you have the Express within 20 feet of the Extreme there may be some form of Wi-Fi interference (like walls) that may be preventing the 5 GHz band to be extended properly.
    To rule out a possible placement issue, please check out the following AirPort User Tip for details on how to best place your base stations.

  • HELP ibook g3 OSX 10.2.8 no longer detects airport express wireless network

    my ibook G3 OSX 10.2.8, airport admin utility software 3.1.1 no longer can detect the airport express wireless network (powerbook G4, OSX 10.4.11, airport admin utility 4.2; airport express, WEP protected, to DSL modem). i just installed an ipod driver update on the ibook, and wireless networking went down on restart. any help greatly appreciated!

    you name it : com.apple.airport.adminutility.plist
    delete it and do as advised.
    This isn't harmful, because it is only a preference list, so it will be created brandnew as soon as you re-setup the Airport stuff.
    Mac OS X ( especially Jaguar ) has a tendency to corrupt some plists out of the blue, it is more or less harmless and can be fixed with recreating them plus permissions-repair.
    Hint : repair permissions more than one time, it ALWAYS finds something to fix in Jaguar.
    You cannot destroy something with these actions, because it is Unix maintance so usual routines.
    A tool like cocktail or Onyx ( google them, onyx is freeware ) can help you run such ( and more ) routines on a scheduled base.
    Always remember that OS X is no longer "the Mac OS", it is Unix with a nice Desktop, the critical things run hidden in the background, so it has to be treated like any Unix/Linux sort of OS, even if from the outside everything looks nice and kosher..
    Best wishes from Germany

  • PCs suddenly no longer see Airport Express wireless network - please help!

    Hi,
    I am new to this forum and I need help. Two days ago - without me making any changes to settings etc. my Airport Express wireless network at home was no longer visible to any of my devices except to the Powerbook (G4 OS 10.3.9) which controls it. From one second to the next two Vista laptops and my cell phone (Nokia, Symbian OS).
    My Powerbook has no problem connecting through AE to the internet. The two laptops are both able to connect to other wireless networks so they don't seem to be the problem. I just don't understand what caused this sudden drop-off/invisibility.
    I have already tried the following: resetting the base station, changing the channel on the base station (from automatic) removing the network security altogether (from WPA2). But none of the devices except the powerbook can now see or detect my network.
    Please - if anyone knows what the cause of this problem could be or how to fix I would be very grateful!!

    you name it : com.apple.airport.adminutility.plist
    delete it and do as advised.
    This isn't harmful, because it is only a preference list, so it will be created brandnew as soon as you re-setup the Airport stuff.
    Mac OS X ( especially Jaguar ) has a tendency to corrupt some plists out of the blue, it is more or less harmless and can be fixed with recreating them plus permissions-repair.
    Hint : repair permissions more than one time, it ALWAYS finds something to fix in Jaguar.
    You cannot destroy something with these actions, because it is Unix maintance so usual routines.
    A tool like cocktail or Onyx ( google them, onyx is freeware ) can help you run such ( and more ) routines on a scheduled base.
    Always remember that OS X is no longer "the Mac OS", it is Unix with a nice Desktop, the critical things run hidden in the background, so it has to be treated like any Unix/Linux sort of OS, even if from the outside everything looks nice and kosher..
    Best wishes from Germany

  • Airport express extender not connecting to airport extreme

    Mac OSX 10.9.5
    Airport Extreme version 7.6.4
    Airport Express version 7.6.4
    I've done a hard reset of both Extreme and Express, set up Extreme and cannot set up Express as an extender.  Airport utility recognizes the Express, but shows an amber light.  Amber light also flashing on the airport Express, which is within 2 feet of the Extreme.
    "Other Wi-Fi Devices" says no remote airport  base satin is discovered.   Same situation even when connecting the Express to the Extreme via an ethernet

    Temporarily, please power off the AirPort Express and set it aside.
    Restart the AirPort Extreme and check to make sure that it is performing correctly.  There should be a green light on the AirPort Extreme and devices that are in the same room or adjacent rooms should be able to connect to the Internet.
    If you see a slow, flashing amber light on the AirPort Extreme.....
    Open Macintosh HD > Applications > Utilities > AirPort Uility
    Click on the picture of the AirPort Extreme
    Look for the setting for Status
    Click on the small amber dot there and report back with the exact message that you see

  • Problem with airport express extending wifi from extreme

    My setup is an airport extreme wired to the internet with two iMacs connected by wire and an airport express to extend wifi from the extreme to the further parts of my house.  When originally installed about a year ago this arrangement worked perfectly, but I noticed a few weeks ago that neither my iphone, ipad, nor my MBP 13" is connecting to the aitport express anymore and the network extension is not working as intended.
    Last night I investigated the isue and found that the express is connected wirelessly to my extreme because when I wired my MBP to the express and turned off the wireless connection it could still reach the internet.  But, even with the express sitting plugged in next to my iPhone I could not get it to connect to the express - it always uses the extreme and while I'm in range there is no problem.  The problem is that my house is old and the wals tend to cause problems with reception and I can't get wifi in the garden and some parts of the house.
    I have the express and the extreme configured to allow access only by the client macs that I have provided and it looks like the two devices share this information when they are in extend mode (but not sure about that).  When I set up the system I added the aitports mac addresses to the approved list in the access control screen, which seemed to be necessary then though I removed them (the airport mac addresses) fromt he list last night to see what effect this had and biefly the airport did connect to my MBP.  But after returning it to its location where it usually is I have not been able to reconnect to it.
    In brief;  I have an airport express extending an airport extreme wifi, it used to work, but now all wifi clients will only connect to the master.  I have a suspicion that a recent airport update has caused this (both airports are up-to-date) but can't be sure.  I have the express correctly configured to extend the wifi of the extreme as it was originally working.
    One thing I have noticed - I had the express set to use a fixed IP by setting 'static' in the internet screen - this is not the current setting (it's reverted to DHCP) and I cannot force it to update to and remain set to static.
    Does anyone know how I can restore the correct functioning of the express as an extension of the wifi network?
    Thanks
    Damon

    Perform the Factory Default Reset one more time. Hold the reset button until the amber light has been blinking rapidly for 8-10 seconds before you release the reset button
    Run the setup wizard, and wait for screen similar to this to appear, then click on Other Options:
    Select the Add to an existing network option, then click Next and follow the prompts.
    If you are still having difficulty, try running the setup utility on an iPhone or iPad, since Yosemite has a number of bugs in the setup process.

Maybe you are looking for