Airport Express flakes out with 2+ devices

I've had the router for quite some time, and it has never given me issues, until I got my iPhone.
I've used a Nintendo DS, a Nintendo Wii, and my iBook on it and its great. Now that the logic board failed on my G4 (yup, THAT one), I have a Toshiba laptop running both Vista and Ubuntu. Both work great on the Airport.
Enter the iPhone. It connects, and I can browse, but it goes half way into loading the page if the laptop is browsing too, and then all clients get dropped from the Router. If I log out of whatever OS I'm running on the laptop and boot into the other, it still don't work. If the iPhone is shut off, and then the laptop is rebooted/booted into other OS, then the laptop works. Same for the phone. With the laptop off, iPhone works fine.
The airport was originally setup not to hand out IP's. That was done by my wired D-Link router and it handed out 192.168.0.# addresses to everything, passing through the Airport. Worked great for years. Now I've tried setting the Airport to assign IP's, but in doing that, I have lost the ability to configure it from windows as my other machine is wired (it worked before setting the airport to assign IP's).
I have gone as far as setting up Static to EVERYTHING so that IP conflict is not an issue. DNS is right, all pointing at the same address. No subnet issues, Multicast is set to default. No interference robustness. Signal strength is at max, on Channel 6 (was channel 1 first, tried 6 with no luck) I believe security is WEP. Microwave not causing the issue. No house phones at all (rule out 2.4GHz interference) and its not blocked or near anything metallic. None of the other machines (both windows PC's - wired) have issues when this happens. it only effects the wireless clients.
I purchased a new wired router (D-link) and still no luck. I have noticed that my Wii gets a new IP lease every 3 minutes, but that may just be the Wii itself.
Firmware on the Router is the latest one. The Wii is connected fine if either the iPhone or Laptop is online, but not when both phone and laptop are on.

I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Power-up the modem; wait at least 10-15 minutes.
Power-up the base station; wait at least 5-10 minutes.
Power-up your computer(s).
In this basic configuration, computers connected to the base station, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

Similar Messages

  • Airport Express Not Working with All Devices

    My airport express has been working fine.  All of a sudden, it stopped working with iPad and MacBook, but iMac is still working fine.  Firmware is updated.  What to do?  Help~~~!

    Which version of Windows and Service Pack is your Dell PC running?

  • I have qualitynet either wired internet. I buy a card good for a month at a time, I can only log into one device at any one time.  Are there settings I can adjust on my airport express to allow all my devices to connect to wi-fi without having to log out.

    I have qualitynet either wired internet. I buy a card good for a month at a time, I can only log into one device at any one time.  Are there settings I can adjust on my airport express to allow all my devices to connect to wi-fi without having to log out of one devise before using another?

    Some Internet providers that limit access to a single device at a time do so by the device's hardware MAC address. If your ISP is one of those, you may be able to substitute the MAC address of your AirPort Express base station for the computer. I would suggest that you contact them to find out if this is allowable.

  • HT4587 I downloaded Airport Express Utility 5.6 to get my Airport Express to work with the latest Mac OSX 10.7.4, but when I install and run it, it still says my Airport Express is out-of-date and needs the 5.6 utility.

    I downloaded and installed Airport Express Utility 5.6 to get my old Airport Express to work with the latest Mac OSX 10.7.4, but when I install and run it, it still says my Airport Express is out-of-date and needs the 5.6 utility. What's up?

    It is likely that you downloaded AirPort Utility 5.6.1.  If you checked the requirements, this only runs on Leopard or Snow Leopard Macs.
    You have Lion, so you need AirPort Utility 5.6 for Mac OS X Lion

  • I am currently using the Airport Express to work with a Bose Wave radio.  3.5 MM jack out and phono connectors into Bose.  Is there a way to hook to a new Bose Wave which does not have phono input plugs?

    I am currently using the Airport Express to work with a Bose Wave radio.  3.5 MM jack out of the Express and phono connectors into Bose.  Is there a way to hook to a new Bose Wave which does not have phono input plugs?

    The latest Bose Wave SoundTouch music system still uses a single 3.5 mm analog Aux port. You would connect the two using an analog audio cable with 3.5 mm stereo jacks on either end.
    An example cable would be located here.

  • Airplay won't connect to my Airport Express & is intermittent with Airport Utility

    Hi
    Yesterday, my iTunes 10 stopped connecting via Airplay to my Airport Express. It spent a long time displaying a Connecting message, then finally gave me this error message: "An unknown error (-15006) occurred while connecting to the AirPlay device AirPort Express”.
    I have a Macbook Pro 2.5 Ghz Intel Core i5 (6 months old). 4 GB 1600 MHz DDR3.
    Running OS X 10.7.5.
    My main modem/router is a Livebox and I usually going my Airport Express to the Livebox network to play music.
    My Airport Express is 802.11g
    All my equipment is within a radius of 2 or 3 feet.
    I'm aware of at least one other recent thread about this problem (https://discussions.apple.com/thread/4150757?tstart=0), but none of the solutions suggested have resolved my problem, so I have summarized a list of the actions I have so far taken to try and resolve the problem. Hopefully, this will help others sort this issue out for themselves.
    ACTIONS TO SOLVE ISSUE
    1. Ran Airport Utility 6.1, which was unable to find my AX.
    2. Downloaded, installed & ran Airport Utility 5.6. AU 5.6 still couldn't find my AX, giving me this error message:
    "AirPort Utility was unable to find any AirPort wireless devices. Make sure the AirPort wireless device you want to set up is plugged in and in range of your computer, and then click rescan to try again."
    3. Unplugged the AX and did a hard reset. AU found my AX and I configured it to join my Livebox network. After being configured, the green light came on the AX, which also appeared on the AU list of devices. However, AU still had the message "Waiting for Airport Express to reset…" with a spinning ball for several minutes. So, I closed the AU window (as AU advised), and reopened it. Happily, the AX was still listed.
    4. Reopened iTunes and tried to select my AX as speaker output. At that exact moment, the AX vanished from the AU list of devices and, after the long wait, iTunes gave me the same error message as before:
    "An unknown error (-15006) occurred while connecting to the AirPlay device AirPort Express”.
    When I tried to rescan for devices in AU, I got the same error message:
    "AirPort Utility was unable to find any AirPort wireless devices. Make sure the AirPort wireless device you want to set up is plugged in and in range of your computer, and then click rescan to try again."
    5. Hard reset and configuration of AX. This time I didn't close the AU window, I waited for the AX to reset. When the spinning ball finally vanished, I got this error message:
    "An error occurred while reading the configuration. Make sure your Apple Wi-Fi base station is plugged in and in range of your computer or connected via Ethernet and try again. (-6753)"
    6. Apple help pages suggested updating the AX firmware. I downloaded the firmware update, did the AX hard reset/configuration routine, then tried to run the firmware installer and got this error message:
    "An error occurred while attempting to communicate with the AirPort Express. (-8)"
    7. Ran all the software updates, including upgrading to iTunes 11.
    8. Spent over 5 hours doing many many hard resets of the AX, combined with iTunes restarts, MBP restarts etc. Along the way, I discovered that if I hard reset  & configured the AX, after a few minutes, AX would disappear from the AU device list without me doing anything.
    9. Attempted to change IPv6 options, using following methods:
    a. System Preferences -> Network -> Advanced -> TCP/IP ->   IPv6 _> Link-local only
    b. In Terminal.
    networksetup -listallnetworkservices
    networksetup -setv6off Wi-Fi
    Neither method had any effect on the ability of AU to see my AX.
    Phew! I'm now exhausted & rather demoralised. Anyone got any other ideas?

    I have been dealing with this for days now. I'm not sure what the solution is either, I've spent most of my vacation from work attempting to get it to work with my speakers and printer, none work still!!
    It seems like a lot of ppl are dealing with these errors but there isn't one solid solution out there.
    Try to set the AX wirless setting to "off" and only have it work for Airplay, Does it work for you?
    One last thing, could this be an update problem? As in, you update your firmware/software and it renders the AX obselte. My AX is old probably a little older than 4-5 years, what about your?
    I would really like to get this to work as I do not think I need a new AX to make this work.
    Let me know your thoughts.
    B.

  • Can't Get Airport Express To Work With ATT's Uverse

    For years, AE worked just fine with my 2Wire portal streaming music to my stereo. Went to Uverse 2 months ago, and AE quit working. I am not using an Airport base station, just the Uverse modem and I need help getting it to work.
    There is nothing in this forum when I search for uverse, so I post this in hope someone can help me.
    I reset AE it and it finally appeared in Airport utility with a yellow light. I click configure and when I choose to join my current network, it sets up it's own Apple network, removing it from Airport utility and changing Airport status in Network to yellow.
    No matter what I do or how I try, I just can't get AE to work with the stock 2Wire modem.
    Has anyone been able to get AE to work with just the 2wire router & not have to buy an airport base station.
    Any help is REALLY appreciated, as I wanna hear my Christmas music, and it's turning me into a Grinch!
    Thanks!
    Message was edited by: Chris Winkler1

    +However, it asks for the security and all I see is WEP in the Home Network set up, I don't know if it's 40 or 128+
    AT&T set this up, so only they can tell you for sure. My guess would be WEP 128 since this type of security is stronger than WEP 40.
    +And it asks for a wireless password. I entered the one from the router & it did not work. Tried the Key and it did not work.+
    This is the same wireless password that you would use if you were logging on to your wireless network with your computer. But, unless you first have the exact, correct security setting for your 2wire router, the password will not work.
    +Has anyone out there successfully got their Airport Express to work with Uverse????+
    I don't provide instructions to anyone on the forum unless I've first done it myself. I'm providing you with the same instructions that I used to help a neighbor with his 2wire Uverse setup last week. It works fine.
    But, he called AT&T to ask them what security setting they used on his 2wire router. Otherwise, we would have had to try each possible setting to see if we could make it work.
    AT&T also told him that his password should be 13 characters, all lower case letters with no spaces. That is what the neighbor said he used. I cannot confirm this as he did not share his password with me.
    AT&T may have set up the password criteria differently on your router. You need to confirm with them on this.
    +What password goes in the Base station tab, Key or Password?+
    Any password you want. This is a separate password simply to be able to access the settings on the device in the future when you are using AirPort Utility. You could use your wireless network password if you want.
    Please post back on your progress.

  • Airport Express dropping out constantly so I can't print wirelessly

    I have an iMacG5 running OSX 10.3.9. I have a DLink wireless router which creates my wireless network that the iMac connects to. Also, as my printer as at the other end of the room, I have an airport express connected via USB to the printer so I can print wirelessly. Everything worked like a dream for about 12 months. Until recently I had no security on this network and although I was aware this was risky, I was reluctant to change anything because it all worked so well. But my paranoia got the better of me and I changed the DLink to WPA security. Ever since then, the airport express has acted very strangely. The connection dropped and I was required to do a hard reset. I did that and everything worked. I felt so smug that I had worked out a computer issue! Little did I know that as soon as I shut down the system the airport express dropped out again. I have since discovered that I don't actually need to shut down for the thing to drop out. It just does it of its own accord.
    I have contacted AppleCare 3 times and spent a total of about 4 hours on this to date. No luck. They suggested interference. However my airport icon usually shows either 3 or 4 bars and there is no difference when the thing drops out.
    The only thing I have learned is that Airport Express does not have to be reset all the time. In my situation, it is best to just unplug it, let it rest for about 30 seconds and then you should be able to see the thing in the airport admin utility. It does take a while and several rescans in the utility, but eventually it does show up. This at least means I don't have to constantly set it up to join the network.
    In fact, really it is a doddle to print! I don't know why people like to just go File-Print when you can go through the delight of getting out of your chair, unplugging Airport Express, waiting 30 seconds, looking at the dust under the cupboard thinking I really must get that, plugging the airport express back in, watching the light change from green to amber, to flashing amber, wait for it...wait for it...it's not happening....waiting...finally - green!. Back to the computer, go to Finder - Applications - Utilities - Airport Admin Utility, not showing up, rescan, not there, rescan, rescan, rescan, still not there, rescan, oh good, airport express is showing up. Now, go to Printer setup utility, delete the printer that is there, then add printer, select rendezvous, add my hp, OK......now I can hit File - Print.
    Has anyone got any ideas on how I can join the boring legions of people who are oblivious to the joys of printing my way?

    Hi,
    I am currently replying to this as it shows in the iChat Community.
    I have asked the Hosts to move it to Snow Leopard  (you should not lose contact with it through any email links you get)
    I also don't do Wirelss printing so I can't actaully help either.
    10:01 PM      Friday; July 29, 2011
    Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb( 10.6.8)
     Mac OS X (10.6.8),
    "Limit the Logs to the Bits above Binary Images."  No, Seriously

  • HT1515 How can I use Airport Express (1st generation) with OS X Mavricks?

    How can I use Airport Express (1st Generation) with OS X Mavericks?

    1st Generation AirPort Express will work fine with Mavericks.
    Are you sure that you have a 1st Gen Express?
    Check the model number on the side of the Express. 1st Gen is A1264.
    If you see A1084 or A1088, these are much older versions of the Express that were sold long before Apple began to use the Generation naming with "n" wireless devices in 2007.
    Mavericks will not support the A1084 or A1088. Use another Mac running Leopard, Snow Leopard, or a PC if you need to administer the older Express.

  • Airport express not working with apple products

    We have been trying to get airport express to work with a macbook pro, ipad2, iphone, laptop, htc wildfire - havent even tried the air music or printer yet! 
    We have a green light on the airport express which is connected to an ntl cable modem(virgin media network).
    Currently the only thing that will connecy is the laptop and my htc phone.  All the apple products will not connect? 
    We went to the apple store today and it worked grand when it was plugged in - the apple products all worked.
    The network comes up on ipad2 but when you press connect it says 'unable to connect'
    can anyone help us please?
    thank you

    I have the same issue.  Mine fixed itself for a bit and now it's broken again.  I'm thinking it's going to be intermittently broken.  I've tried turning both devices off and on again but that did not help.

  • I'm using iTunes 9 and I recently just bought AirPort Express. I have used it before in the past put the problem I have now is that I cannot select the Express network for my speakers. Does Airport Express only work with iTunes 10 or 11?

    I'm using iTunes 9 and I recently just bought AirPort Express. I have used it before in the past put the problem I have now is that I cannot select the Express network for my speakers. Does Airport Express only work with iTunes 10 or 11?

    Hello Hornet12,
    Indeed, iTunes 10.2 or later will be required to utilize AirPlay.
    Using AirPlay
    http://support.apple.com/kb/HT4437
    AirPlay requirements and capabilities
    To get full AirPlay features, make sure your AirPlay-enabled devices are running the latest software updates. The table below identifies minimum AirPlay requirements and capabilities:
    Stream content from
    Requirement
    Notes
    iPad
    iOS 4.3 or later.1
    From the Videos, iPod, Photos, Music, and YouTube apps on iOS devices, stream videos, music, and photos to an Apple TV (2nd and 3rd generation), or stream music to an AirPort Express or compatible third-party device.
    With iOS 4.3 and later, you can also stream video and audio from a website or a third-party app installed on your iOS device if the developer for the app or website has added AirPlay functionality.
    iPhone (3GS or later)
    iPod touch
    (2nd generation or later)
    Computer
    iTunes 10.2 or later.
    Stream videos and music from your iTunes library to an Apple TV (2nd and 3rd generation), or music to an AirPort Express or compatible third-party device.
    Apple TV
    Apple TV software version 5.1 or later.
    Stream music from your Apple TV to another Apple TV (2nd and 3rd generation), to an AirPort Express or compatible third-party device.
    Cheers,
    Allen

  • HT1998 what is the latest update for Airport Express 802.11n with the Mac OSX10.6.8

    what is the latest update for Airport Express 802.11n with Mac OSX 10.6.8?

    You can find out as follows:
    Open Macintosh HD > Applications > Utilities > AirPort Utility
    Click the AirPort Express
    Click Manual Setup
    Click directly on the word Version (3rd line)
    If there are any updates, you will be notified.
    If there are not any updates, you have already have the latest firmware.

  • Apple AirPort Express Base Station with 802.11n - MB321LL/A. How to set it up to my new iMac

    Community:
    How do you set up an
    Apple AirPort Express Base Station with 802.11n - MB321LL/A how do you set up on Mac running on OS X 10.9.4?
    Please advise
    Fmsalazar

    Apple did say it was important.
    If the units do not show up in the airport utility then you must set it correctly to link-local.
    Steps for OS X Lion or Mountain Lion
    This can happen if IPv6 has been disabled. To enable IPv6 for your network interface:
    Choose Apple menu () > System Preferences, and then click Network.
    If a lock icon appears in the lower-left corner, click it and enter your admin name and password to unlock the pane.
    Click your network service (Wi-Fi or Ethernet) in the list, and then click Advanced.
    Click the TCP/IP tab.
    Choose Link-local only from the Configure IPv6 pop-up menu.
    Click OK.
    Click Apply.
    AirPort base station not seen or "An unexpected error occurred" appears in AirPort Utility 6.3
    Apple rep says the same.
    Re: Unexpected error when connecting Airport Express A1264 to Airport Utility 6.3.1
    I am searching as I saw it in a thread today where a person had issues. (No contribution from me in the thread but found that was the issue).
    It is kind of a fail safe.. since auto can end up with any setting.. and it will depend on the setting of ipv6 in the Airport Router if it works properly in the computer.. setting it to the correct value is one step in sorting out problems when people get in a mess.

  • Should airport express be configured with the same network as my existing router

    Should airport express be configured with the same network name as my Verizon router.

    Carolyn1962 wrote:
    I am new to apple,used to windows.Apple store advised airport express in order to boost my DSL router.In order for it to be most effective should it be under the same settings.Still learning
    A router signal can not be boosted as all routers put out the maximum allowed by law.  However, proper placement of a secondary router will enable it to "repeat" or extend the signal.
    An Airport can "extend" the WiFi created by another Airport.  It can not extend a non-Apple WiFi.  You need TWO Airport units, one to function as the main radio and the other to function as an extender.  I used two Express units.
    Configuration is simple if you start from a factory default condition.  Connect the main Airport to AC power and finally to the Internet modem (or modem/router).  Open Airport Utility on your Mac or other computer and accept all of the recommendations.  After confirming that it works, insert your desired administrative and WiFi passwords.
    Then connect the extender to AC power.  As before, open Airport Utility on your Mac or other computer and accept all of the recommendations.  No need to add password info.
    Do not expect the Airport to respond instantly to the configuration commands.  BE PATIENT!

  • My airport express is stuck with a solid amber light.

    I have reset via hard reset instructions and also factory default by holding in the reset button while plugging in the device. My internet connection works fine when I hard wire connect it to my mac but airport utility will not recognize the airport express

    My AirPort Express is stuck with a solid amber light.
    If that is the case, and several tries at a Factory Default Reset have not been able to free up the lockup, then it is unfortunately likely that the AirPort Express has experienced an internal electronic component failure and will need to be replaced.

Maybe you are looking for

  • Negative Values

    Hi Can we use Negative values in BLOB and CLOB. Please help me Thanks Ramesh

  • Question about Organizer in Photoshop Elements 8

    I used to download photos into the organizer and they would show up in a window that displayed only the current photos being downloaded. I must have done something to change that because now photos go directly to the main organizer window. I have a l

  • SAP Certified Development Associate - ABAP with SAP NetWeaver 7.0

    Hi, this is kumar from bangalore. Please let me know where can i get the materials to prepare for the certification exam. Regards, kumar

  • Problem in installing JAVA WAS 6.4 (not sneak preview)

    Hi, Struck up at STEP-28 of 33 which is Configure SAP j2ee engine . Error log says CJS-20067 BatchXmlGenerator error.DIAGNOSIS: Error when generating 'Batchconfig.xml' for the batchconfigtool.See output of logfile c:\program files\saninst_instdir/bat

  • Resetting settings. Please help.

    Hello everyone, I have just bought Macbook pro. I started using it and everything seemed to be fine, but when i tried to install online game, i had to choose program to open instal and i have chosen wrong (script editor). I cant restore it, i cant op