Airport Express, hidden network, no automatic connection

Howdy,
I now have received my 24" for 3 hours
Happy camper here
I have one issue which I can't figure out.
Its about connecting automatically to my Wifi Network.
I have two wifi networks, one Airport Express and one 'other brand'.
Both with hidden SSID and WPA paswords.
Now when I connect manually to these networks, all goes OK.
Then I have created a profile under system preferences /network:
Under the Airport tab:
By default, join: 'Preferred Networks'
After which I have added the two networks with network name and password.
under network ports tab:
I have switched of ethernet and moved airport all the way up.
What I can't figure out:
When I re-boot, it does not automatically connect to any of these networks. I have to do it manually always.
I have tried using the set-up assitant, but it gives me a bad-password error (while I am 200% sure its correct) probably cause I can not select the authentication method.
Any ideas ?
B

I gave up and haven't bothered.
MAC addressing and Password should be enough.

Similar Messages

  • Iphone will not connect to airport express extended network - macbook and ipad will - Help

    Iphone will not connect to airport express extended network - macbook and ipad will without problems.
    iphone will connect to base station no problems, I've restored settings and started again but still the same, the iphone picked up the network for the last couple of months, but not now ?

    I'm having the same issue. My AExpress used to give a good signal strength on the far side of the house extending he network created by my Extreme. However, I've noticed lately that my iPhone does not receive the same strong signal it once did. AE has a green light, I've rebooted it, and my Extreme but there is no change in signal strength. Other than the green light, how can I tell if the Express is working if I don't get a good network signal?

  • HT1145 I have an older plug in version of Airport Express and am trying to connect it to my wifi network to boost coverage but it is not connecting to my network.

    I have an older plug in version of Airport Express and am trying to connect it to my wifi network to boost coverage but it is not connecting to my network.

    What is the make & model of the wireless router that you are trying to "boost" with the AirPort Express? Is your Express an 802.11g or 802.11n model? Is the connection between routers going to be a wired or wireless one?

  • PCs suddenly no longer see Airport Express wireless network - please help!

    Hi,
    I am new to this forum and I need help. Two days ago - without me making any changes to settings etc. my Airport Express wireless network at home was no longer visible to any of my devices except to the Powerbook (G4 OS 10.3.9) which controls it. From one second to the next two Vista laptops and my cell phone (Nokia, Symbian OS).
    My Powerbook has no problem connecting through AE to the internet. The two laptops are both able to connect to other wireless networks so they don't seem to be the problem. I just don't understand what caused this sudden drop-off/invisibility.
    I have already tried the following: resetting the base station, changing the channel on the base station (from automatic) removing the network security altogether (from WPA2). But none of the devices except the powerbook can now see or detect my network.
    Please - if anyone knows what the cause of this problem could be or how to fix I would be very grateful!!

    you name it : com.apple.airport.adminutility.plist
    delete it and do as advised.
    This isn't harmful, because it is only a preference list, so it will be created brandnew as soon as you re-setup the Airport stuff.
    Mac OS X ( especially Jaguar ) has a tendency to corrupt some plists out of the blue, it is more or less harmless and can be fixed with recreating them plus permissions-repair.
    Hint : repair permissions more than one time, it ALWAYS finds something to fix in Jaguar.
    You cannot destroy something with these actions, because it is Unix maintance so usual routines.
    A tool like cocktail or Onyx ( google them, onyx is freeware ) can help you run such ( and more ) routines on a scheduled base.
    Always remember that OS X is no longer "the Mac OS", it is Unix with a nice Desktop, the critical things run hidden in the background, so it has to be treated like any Unix/Linux sort of OS, even if from the outside everything looks nice and kosher..
    Best wishes from Germany

  • HELP ibook g3 OSX 10.2.8 no longer detects airport express wireless network

    my ibook G3 OSX 10.2.8, airport admin utility software 3.1.1 no longer can detect the airport express wireless network (powerbook G4, OSX 10.4.11, airport admin utility 4.2; airport express, WEP protected, to DSL modem). i just installed an ipod driver update on the ibook, and wireless networking went down on restart. any help greatly appreciated!

    you name it : com.apple.airport.adminutility.plist
    delete it and do as advised.
    This isn't harmful, because it is only a preference list, so it will be created brandnew as soon as you re-setup the Airport stuff.
    Mac OS X ( especially Jaguar ) has a tendency to corrupt some plists out of the blue, it is more or less harmless and can be fixed with recreating them plus permissions-repair.
    Hint : repair permissions more than one time, it ALWAYS finds something to fix in Jaguar.
    You cannot destroy something with these actions, because it is Unix maintance so usual routines.
    A tool like cocktail or Onyx ( google them, onyx is freeware ) can help you run such ( and more ) routines on a scheduled base.
    Always remember that OS X is no longer "the Mac OS", it is Unix with a nice Desktop, the critical things run hidden in the background, so it has to be treated like any Unix/Linux sort of OS, even if from the outside everything looks nice and kosher..
    Best wishes from Germany

  • Can't find Airport Express via wireless or wired connection.

    I've run across this topic in this forum and a lot of others and nothing I've found has helped resolve the issue. It seems like the one definitive answer I found was to return it to the store, but I'm hoping to avoid that so I figured I'd try once more.
    Running Windows XP and using a linksys Wireless-G network card. When I first got the Airport Express I was able to connect to it but then I had some issues with my cable network connection and had to reset everything. Since then I haven't been able to connect to it, and currently I can't find it using the Base Station. Tried resetting it to factory defaults about 10x and I'm still stuck on blinking yellow. I tried connecting it directly with a network cable and even then my computer can't seem to find it.
    I tried turning off my firewall, reinstalling the Airport Utility, connecting to the IP address 10.0.1.1 using the "Configure Other..." box and no luck.
    Any suggestions?
    Thanks much.

    The issue is within the network configuration of the Airport Express. As you mentioned, all hardwired devices can use AirPlay but all wireless devices can't.
    Normally, the Airport Express will wirelessly join your existing network, and Airplay will work with all devices. Any reason why you have your Airport Express connected to your router via ethernet?

  • Airport Express WiFi network MAC address filtering not working

    I have an Airport Express WiFi network which I bought and installed new in 2011. Initially I enabled MAC address access control and populated a list. It was working perfectly, I know, because a niece visiting tried to connect her iPhone and could not until  I added its MAC address to the allowed list. Now however, anyone can connect without being added to the list. I think I read somewhere that a recent firmware update permanently disabled MAC filtering in Airport Express, even when it was previously working? Can anyone enlighten me about what's going on here?

    In a sense those are/were/should operate as two separate functions, which they did before recently.
    They do operate as two separate functions.....but it all depends on how you have the default rule setup in Timed Access.
    If the default rule in Timed Access is set to No Access.......then a wireless device cannot connect....even it has the password for the network.....unless it has been setup on the list of allowed devices in Timed Access.
    I have checked this 3 times this evening to verify. It works as it always has, and as expected.
    If the default rule in Timed Access is set to Unlimited, then any device can connect to the network if it has the password. Devices that are listed or specified in Timed Access will be allowed to connect at the specific times that have been set up for each device.
    So, if you want to use the more traditional MAC Access Control settings, the default rule has to be set to No Access and then you must set up a rule for each device that you want to allow to connect to the network. Only devices on the Timed Access list will be allowed to connect to the network. Other devices will not be able to connect to the network....even if they have the correct password.
    If a recent firmware update has changed things from what they have always been.....then I am not affected....and I should be if I am using the same firmware as others.

  • Airport express second generation do not connect to the internet

    Airport express second generation do not connect to the internet. I changed my location and the problem happened . Earlier it was running smoothly. I am not finding the cause of the problem. I switched on and off several times but the problem persists. Please help me.

    Are you asking the make/model of the computer or the AX base station?
    Neither, I was interested in the make/model of the cable modem.
    Our ethernet connection was fried in an electrical storm so we had to go wireless.
    Electrical storms are never a good thing when it comes to electronics. What was/is your current network configuration? Is it something like the following?
    Cable modem > (Ethernet cable) > AX > (wireless) > wireless devices
    Is there another router, other than the AX, in the configuration? ... or an Ethernet switch? I'm just trying to understand your network to best advise you on how to configure the AX.

  • Unable to register to Airport Express wifi network

    I have a Time capsule, and I'm using a AirPort Express to extend the network. The setup is pretty straightforward, and it has been working.
    However quite often my devices (2 iPhones 5s; iPad 2; and event a MacBook) often lose the connection to the wifi when using the Airport Express (too far from the Airport Extreme Time Capsule signal). Opening the wifi menu, the devices detect the network, try to join... But seem not to actually be able to register. No error message appears do, just the circling wheel keeps runing.
    All the devices firmware and iOS are updated. Can't figure out what's wrong. Could it be the fact that the Airport Expresss and the Airport Extreme were originally bought in different countries?
    Thanks in advance for the support.

    Hi Brett,
    Thanks for the reply. But the issue is not with the iOS devices. I experience the same problem with the MacBook.
    The issue seems to be with the Airport Express that somehow loses the connection to the Time Capsule. Usually if I restart the issue tends to resolve it self. But I endup doing this on a regular basis...
    Any ideas?

  • Linking Dell Laptop to existing/working Airport Express wireless network

    Hi,
    I'm trying to connect a Dell Laptop (Inspiron 2500) running on Windows XP to an existing and functionning Airport Express wireless network set up for my girlfriend's iBook. It works perfectly for the iBook.
    I have outfitted the Dell with a D-Link wireless G USB adapter and I see the network (i have the password) and it says I am connected to the network (even says connection is very good).
    However, when I open the internet browser, nothing.
    The network set up is: Cable to RCA Digital modem (model DCM425) to Airport Express (via ethernet) and to computer.
    I have tried playing around with the Dell Laptop settings (IP, DSN, etc ...) and I have called everyone involved (including Apple) to no avail.
    Any help would be greatly appreciated!
    Thanks,
    Nick
    Dell Laptop   Windows XP   iBook

    Thanks for the reply.
    WEP is enabled. As far as the encryption, I'm not sure. I believe that it's 64-bit, as the password for the network is a five-letter word.
    The funny thing, though, is that I had been using an IP address which I found on my girlfriend's Ibook, which allowed me to connect to her AEBS network, although the internet browser showed no connection.
    Following directions from somebody else, I removed the IP address to enable DHCP, and then I was able to connect to other networks in the area (and the browser also connected to the internet) but I couldn't get onto her network anymore. Even with the password ...
    Any ideas?
    If i'm supposed to upgrade to 128-bit, how should I go about doing that?
    Thanks again for the reply.
    What encryption are you using?
    Do you have WEP enabled?
    The problem you are having probably lies with the
    encryption key.
    ccessing a Airport Network with a Windows XP PC or
    laptop (with XP SP2)
    http://www.ifelix.co.uk/tech/1011.html
    Accessing a Airport Network with a Windows XP PC or
    laptop (with XP SP1)
    http://www.ifelix.co.uk/tech/1010.html
    iFelix

  • I use Airport Express to network 3 iMacs to a DSL modem.  Recently, the network became undiscoverable to one of the iMacs.  Suggestions for a fix?

    I use Airport Express to network 3 iMacs to a DSL modem.  The network has become undiscoverable to one of the computers. I have reset the base station to factory settings but this does not help.  The other two computers are unaffected. All 3 computers can access the internet when connected directly to the modem.  I suspect the problem might be the Airport card?  Suggestions?
    beaucleo

    Thx for the suggestion, although I didn't have to reset the SMC to fix the problem. The problem was the handshake between the security password and the designated network.  The following links gave me info for investigationg the problem.
    http://support.apple.com/kb/HT4199
    http://www.ehow.com/how_6831952_test-airport-card.html
    http://www.youtube.com/watch?v=aXiZn64aZfg
    http://www.cnet.com/news/how-to-invoke-and-interpret-the-apple-hardware-tests/
    I would recommend these web sites to anyone who is having problems setting up and/or maintaining a wifi system.
    I discovered after reading one of the web references that if I disabled nework security the problem went away. This, however, was unacceptable.  Further experimentation showed that the solution to my problem was to change the name of my network while keeping the same password.  I tried only changing my password but that didn't help.  I still don't understand why only 1 of the 3 networked iMacs was affected.
    Again, thx for your interest and reply.
    beaucleo

  • I have lost my Airport Express Password.It is still connected to some devices. Can I recover it and if not how do I reset it?

    I have lost my Airport Express Password.It is still connected to some devices. Can I recover it and if not how do I reset it?

    If you can connect to your wireless network and you're using an Apple AirPort Base Station, then simply use AirPort Utility. From the Base Station menu, select Show Passwords...
    Or, reset your wireless network password by momentarily depressing the reset button on your AirPort Extreme, Express, or Time Capsule. Press the button for one full second, no more. Then, configure a new password using AirPort Utility.
    If you can't connect to your wireless network, or you are not using an Apple AirPort Base Station, you can use the procedure that follows below to retrieve it from your Mac's Keychain.
    Your wireless network password is stored in your Mac's Keychain.
    You must first have an Administrator account on a Mac that you use with that AirPort Base Station, one that is used to connect to your AirPort network.
    On that Mac, open the Utilities folder. Find Keychain Access and launch it.
    In the search field at the upper right, type Airport. All the Keychain entries for your base station will appear there, as well as other entries.
    Look at the column "Kind". The entry you want to select will be labeled "AirPort network password" (not "AirPort base station password" or anything else).
    If you are trying to recover the AirPort Base Station password then the entry you want to select will be labeled "AirPort base station password" not "AirPort network password".
    Double-click that, and in the window that appears check the box for "Show password".
    You will get the following window:
    In the Password field type your Mac's Administrator password - the same one you used to log in to that Mac.
    Then, click Allow, and your wireless network password will appear in the "Show password" field:
    Make note of it.
    Close the window, then quit Keychain Access.

  • TS1589 I have to reboot my BTinfinity router to enable me to link my ipod to Airport express. When it is connected it works perfectly, but it is getting a bind to have to keep switching the router power off. Any one help???

    I have to reboot my BTinfinity router to enable me to link my ipod or my iphone to Airport express. When it is connected it works perfectly, I use it to play music through my BOSE soundwave, but it is getting a bind to have to keep switching the router power off. Any one help???
    Ipod touch: 4th generation Upto date software
    Airport Express: Latest model
    Iphone 5: Upto date software

    This can sometimes be the result of a faulty/damaaged USB sync cable.  Do you have another cable you could test it out with?
    B-rock

  • Airport express and itunes won't connect

    I am running an airport express with itunes. I can no longer connect my wireless itunes to the airport express. I once did connect to my airport express.I have tried to update the firmware and get error messages that I cannot update the firmware.
    I also have a new iBook which also will not connect to the airport express
    I am using a powerbook, wireless Netgear router and an airport card. I updated all software systems( itunes and all OS X updates)
    Any suggestions?

    That page won't load for me. Any suggestions?
    You can find it here:
    http://discussions.apple.com/thread.jspa?messageID=1113575
    There was a change in the forum software which means that the previous link is now dead, but the message is still available.
    iFelix

  • Airport express 802.11b doesn't connect to Linksys E3000

    airport express 802.11b doesn't connect to Linksys E3000
    Linksys told tha de the device does not support WPA security
    BUT
    the device has capability to WPA and it was working on Linksys WRT 310n v2
    is out there an solution?

    If you have tried numerous default resets, then the Express is defective. Normally, it displays a solid amber light...or no light.... when an internal component fails, but I've seen the solid green as well.
    If it's in warranty, Apple will replace the device. 
    If it's not....and you want to try a real longshot....carefully saw open the case along the center seam to open up the device.  You might get really lucky and find something obvious like a connector that has come loose, or something similar.

Maybe you are looking for