Airport Express Network just for Music (Airplay)

Hello all,
Please can someone help me out? I had this working before the latest firmware update but can't get it working again.
I have six airport expresses that I have bought for the sole purpose of streaming music around my house. I can't get the network running again and run into problems with IP address and DNS servers.
I run iTunes on a Windows 7 machine which connects directly the internet with my router. I want to create a second wireless network using a Airport Express as a base unit which will be for the purpose of streaming music round the house. The Aiport Express base unit is attached to my computer with a ethernet cable.
The problem is, that when I set up the second network using ip address 10.0.0.1 etc it needs to get a DNS server from somewhere. I think that this is the only thing holding me back but am not sure about this.
Can anyone offer any advise? Or am i best just to use my existing wireless network to stream music around my house. I would rather have the second network....
Cheers,
Mark.

If you only plan on using this second wireless network for streaming, then DNS would not be required as your theoretically will not need to access the Internet on this secondary network.
You can configure an AirPort Express Base Station (AX) for streaming WITHOUT an Internet connection as follows:
The AX would not get a Public IP address, but it would have a Private IP address of 10.0.1.1 ... and it would be providing wireless clients connected to it with Private IP addresses in the 10.0.1.2 - 10.0.1.200 range.
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Create a wireless network
Wireless Network Name: <enter a desired Network Name or SSID>
Radio Mode: <leave the default or select a desired radio mode>
Channel: Automatic
Wireless Security: <select the desired wireless security type>
Internet > Internet Connection
Connect Using: Ethernet
Connection Sharing: Distribute a range of IP addresses
Internet > TCP/IP
Configure IPv4: Manually
IP Address: 10.0.1.1
Subnet Mask: 255.255.255.0
Router Address: 10.0.1.1
DNS Server(s): <leave blank>
Domain Name: <leave blank>
Internet > DHCP
DHCP Beginning Address: <leave default or change to a desired starting address>
DHCP Ending Address: <leave default or change to a desired ending address>
Music
Enable AirTunes (checked>
iTunes Speaker Name: <leave default or enter a desired speaker name>
Advanced > Logging & Statistics
Allow SNMP (unchecked)
Your AX will still report at least three errors: 1) Configuration of WAN, 2) SNMP over WAN, and 3) Double NAT. These can all be safely ignored to stop the AX's status light from flashing amber in this configuration.
Now the issue is how do you set up the other five AXs? If your home has an Ethernet backbone, then you could configure all of the base stations into a roaming network. If you must go wireless, then you would need to configure them into an extended network.

Similar Messages

Airport Express network suddenly no longer visible - but only for one Mac..

What the..?
My 20" iMac Core Duo can no longer see my Airport Express network. It happened yesterday after restarting the AE a few times.. (I do this and also restart the modem from time to time if the net connection stalls - or I want to boot of my housemate's PC from the network cause she's hogging bandwidth)..
Anyway.. The first restart caused it to not re-appear on the list of available networks, so I restarted again.. then it was fine - it came back. All good.
I reset it again this morning because the net connection was not meeting my expectation and now the iMac no longer sees the AE network.
I can connect to other Wi-Fi networks around me (there is a neighbour with no WEP) but cant see hide nor hair of my own network.
The puzzling thing is that my girlfriend's Mac Book, my other iBook G3 and my housemate's PC can all see it and use the network fine - as normal..
So what has happenned? And what do I need to do?
Between you and me ..This intel iMac has been a bit tempramental ever since I got it.. weird things like this happen to it from time to time.. never one thing that you can point at and say AHA! Faulty [something] but just weird stuff like this... Hmmmm..
Some help would be much appreciated.. Thanks!
20" iMac Core Duo 2.0GHZ Mac OS X (10.4.7) 2GB RAM, 500GB HDD, 256MB Graphics

Well, from reading some other posts, and trying my own experimenting, I have gotten it to work.
Deleting the keychain did nothing, manually connecting to the network by typing the name in etc.. nothing.
What DID work was using my G3 iBook (which could see the network) to use the Airport Administrator to change the channel from Automatic to manual - in this case channel 7 (a completely arbitrary choice).
The thing I cannot work out is why it had this issue in the first place. It worked fine for months then one day decided that it apparently didn't like automatic channel selection.
The problem is solved but the cause is still a mystery.
Hopefully though, this might help others with the same problem.
20" iMac Core Duo 2.0GHZ Mac OS X (10.4.7) 2GB RAM, 500GB HDD, 256MB Graphics

Hi, I'm thinking of buying the Airport Express or Extreme for my school dormitory, would i need to plug them into the already existing school internet via LAN cable or do the products just work by themselves?

Hi, I'm thinking of buying the Airport Express or Extreme for my school dormitory, would i need to plug them into the already existing school internet via LAN cable or do the products just work by themselves?

Welcome to Apple Support Communities
AirPort stations aren't modems, so they have to be connected to the modem you are already using. The AirPort Extreme and Express have a WAN port, where you have to plug an Ethernet cable that has to be connected to the modem.
After doing this, you can set up the AirPort station by using AirPort Utility. If you have Windows, download AirPort Utility from the Apple website > http://support.apple.com/kb/dl1547

WRT54G as client for Airport Express Network?

I know this can be done in reverse, with the airport express becoming a client for the WRT54G, but I want the 54G to connect to the airport express network I've already set up. Is there a way, and how?
Thanks!

It is not possible to set up a Linksys WRT54G as a client on a wireless network created by an Airport Express.
Others have noted here (in past discussions) that they have also been unsuccessful at configuring the WRT54G as a remote base station in a wireless distribution system (WDS) where the Airport Express is the main base station.

Sound output to Airport Express horrible except through iTunes Airplay

I've had an Airport Express for 2 or so months now, and I use it for both wifi routing as well as its Airplay functionality, wired into my stereo. I've used it with Airplay directly from iTunes as well as setting the system sound output on my Mac to go over to the Airport Express.
As of today, only the Airplay over iTunes works without issue. When I go to the system sound preferences and select the Airport Express, I hear a very loud pop, and all output is muffled and highly distorted. If iTunes is playing, that sounds bad too. However, with the system sound prefs set to internal speakers and ONLY iTunes set to Airplay, it sounds fine. This is not good at all for me, as I often send audio from Youtube and other streaming sites to Airport Express to play on my stereo.
How can I get sound output to Airport Express from the sound preferences to play nice again?
PS, I have the identical issue with Apple TV, though I don't use it regularly for Airplay. System output to Apple TV is terrible, iTunes Airplay to it is fine, and the audio from content on Apple TV is fine.

Is there any way to output any sound from a computer to Airport Express, not just iTunes?
Yes, check out Rogue Amoeba's AirFoil.

How can I share my Internet from my iPhone to Airport express network?

How can I share my Internet from my iPhone to Airport express network?

YES you can! - Gotta love those "you can't" answers from people who haven't even tried. ;o)
Just have your Airport Express "Join" your iPhone. It will share your Internet connection through its Ethernet port. I currently have an AppleTV connected via Ethernet to the Airport Express. With this setup I have wireless Ethernet AND wired LAN connection. I can even AirPlay to the AppleTV and have Internet at the same time. Haven't tried a switch/hub but see no reason why it wouldn't work. This proves to be very useful to create a wired network with Internet from a cellular device without Ethernet.

Using Multiple Airport Express units to play Music to Multiple Sound System

Goal
- play music on my iMac and in one other sound system(I'am aware of the one
system limit )
- I have multiple Airport Express units(3) for different sound systems and wish
to select the room using iTunes.
Reality
if I reset all the airport express units in the house(3) I can initially see the units. On going through the setup I'am able to configure each unit to be part of my wireless network and get the airport express to power cycle. However after this process only the last AE unit is visable via itunes. If I use the airport utility it can find no units when scanning. If I power cycle one of the non visible units it becomes visable but I cannot play music to the unit and trashes the connectivity to the one working AE unit.
What am I doing wrong ?

Sorry - I led you astray unnecessary in my last posted message. The reference I provided was for setting up a remote base station. That is not applicable to your situation, so please ignore.
In your case, you want to use the Airport Utility to configure each Airport Express so that it "join" (and not "extends") your existing wireless network.
What I suggest you do is:
1. get each Airport Express into a known default state by doing a factory default reset per these instructions. Hold down the reset button for 10-15 seconds, until you see four green flashes in rapid succession
2. put all Airport Express devices, and the wireless Mac you are using to configure the Airport Expresses, into the same room as the wireless router you are using
3. configure one Airport Express at a time, and as I said above use the Airport Utility to configure each Airport Express to "join" the existing wireless network - ie select your Airport Express device as shown in the Airport Utility, click the "Continue" button (not the Manual setup button), and follow the instructions. The name of the wireless network you are joining is the same as the name of the wireless network your existing wireless router is creating. Make sure you also specify the same security protocol (WEP/WPA) and wireless network password as your Mac requires to connect to your existing wireless network.

HT5211 My HP 2355 won't show up in AirPrint? I have it plugged in via USB and set it up on my Mac mini with the airport express network. Any advice?

My HP 2355 won't show up in AirPrint? I have it plugged in via USB and set it up on my Mac mini with the airport express network. Any advice?

Unless your HP printer is an AirPrint-ready device, just connecting it to the USB port of the AirPort Express base station will not make it so.
On the other hand, connecting a non-AirPrint printer to the base station's USB port it can be shared out by the base station's print server. Please see the following Apple Support article for details.

Macbook no longer detects Airport Express Network

I've been using my macbook to connect to my Airport express base station for my home wireless daily for like a year now. Today however, my macbook refuses to connect to the network. After a few scans it detects the network, then when I try to connect it brings up the "this network requires a WEP password" which I put in, and then the connection times out on every attempt.
I tried using the Airport Utility which fails to even detect the base station.
Yes I've restarted my MB, yes I've restarted the express/modem. Thing is, I'm connected to the same network right now on my iPhone which doesn't seem to have any problem.

Update: my macbook can connect to the wireless network at my university, but still not the airport express network.

Connecting Wireless Samsung BluRay Disc to Airport Express Network

I am trying to connect my wireless capable Samsung BuRay Disc Player to my Airport Express Network. The Samsung keeps telling me to check my IP Address, DNS Server, Gateway etc. I have tried to set it up using the auto option and using the manual option. Neither is working. How do I check that my IP address, etc. is correct for connection??

kalh wrote:
I am trying to connect my wireless capable Samsung BuRay Disc Player to my Airport Express Network. The Samsung keeps telling me to check my IP Address, DNS Server, Gateway etc. I have tried to set it up using the auto option and using the manual option. Neither is working. How do I check that my IP address, etc. is correct for connection??
Welcome to Apple's discussion groups.
I looked at a manual for a Samsung Bluray Disc player. They seem to have left out an important capability: the ability to choose a wireless network and supply its password.
You may be able to use the WPS (Wi-Fi Protected Setup) capability, although that is said to be tricky between Apple and non-Apple equipment. Use AirPort Utility to put your AirPort Express into "manual setup" mode. Invoke the menu option Base Station -> Add Wireless Clients. Then follow the player's instructions for "PBC (WPS)". Use the AirPort Utility option "First attempt". The AirPort Express' status light will turn blue while it waits for a connection from the player.
I have no direct experience with this. All the above information came from the electronic book "Take Control of Your 802.11n AirPort Network" (http://www.takecontrolbooks.com/airport-n).
I have no relationship with Take Control Books other than that of a customer.

Airport Extreme Killed My Airport Express Network!!!

I have been an apple user since 1992 - NEVER HAVE I FELT SO FRUSTRATED!!!! Sorry to shout, but this is as bad as it gets - my kids are screaming at me and my wife laughing!! I have had a reasonably good Airport Express network running in my house with an Express as the primary and internet connected to it by the ethernet port. I worked fine for my Intel iMac and my daughters Intel MacBook, but my son had problems in his room. We then got an xbox 360 and wanted to connect that so I upgraded to an Airport Extreme - Disaster!. Firstly the net went intermittant! Then I rebuilt from scratch restting all devices to factory defaults; worse and worse, the network kept failing to find various base stations. Finally I cut the Extreme out of the loop and tried to rebuild the original network; now Airport utility won't see any base station after I configue it!! Please help if you can!!!

If nothing works, try a factory reset: disconnect the Extreme from power, press the reset button, plug in power while still pressing the reset button, release reset button after 5 seconds or so.
This method usually helps me with problems with my Airport Extreme and Express (this happens seldom by the way). The only disadvantage is that you have to set it up again completely.

AirPort Express set up for Outdoor Speakers

I need some advice from those who have used AirPort Express to drive music to a pair of outdoor speakers...I currently have my outdoor speakers (Def Tech AW6500s) set up to my home theatre receiver "B" speakers...When I listen to my music through AppleTV, I can choose to listen to my "A" speakers inside and/or my outdoor "B" speakers. Sometimes the kids want to watch TV or play video games while the adults want to continue to listen to music outside, so that's why I'm thinking of getting a separate system, using AirPort Express, for the outdoor speakers. (Although my receiver (Pioneer Elite 94TXH) supports zoning, I find it a little complicated and not as versatile).
I've done some research on what I'd need for the set-up...basically an additional amplifier hooked to the Airport Express. I've read other posts suggesting I can get an amp for anywhere from a few hundred to the cost of a modest home. I've seen info on the Peachtree Audio Nova which draws raves for digital music, but I'm not sure I need that type of quality (nor price tag) for outside. I'm not an audiophile, but I can tell good sound from bad, so I want some guidance to find the right balance...
I'd appreciate any thoughts!!

Jomobco,
I actually did look at the Sonos system when I was at Magnolia purchasing my speakers. Since I already have a few AirPort Expresses set up for my bedroom and kids' playroom, I thought it might be redundant. I was thinking about the Sonos more though when I started researching the Peachtree Nova and Decco, but I was a little hesitant about spending that much more for the system....It seems like a great system, though!!

Using my Actiontec modem's wifi, it doesn't find my new airport express. When I use the new airport express network I created error message says ip address is wrong. Help setting this new airport express up

Using my Actiontec modem's wifi, it doesn't find my new airport express. Using the new airport express network I just set up it says the ip address is invalid. What can I do to overcome this blinking amber light and error messages?

You need to begin by configuring the AEX to Join an existing network (Bridge Mode.) You can then connect to it using Wi-Fi, but the AEX will not extend your existing network.
If you can connect the AEX to your existing router using Ethernet, then you could use it to Create a new network. Otherwise, if you want to extend your existing network you will need to get a Wireless Access Point - WAP - from a non-Apple product like D-Link.

Time Capsule and Airport Express network extension

Hello,
I have a time capsule using 5GZ network. However i have an issue, as in my bed room the signal is too weak.
I also get an airport express and would like to use it in order to make the signal reach my bed room.
Would you please tell me how i could do so ?
I checked WDS but this option is not available for my time capsule.
Thanks for your reply.

Hello both,
thanks for you reply.
Actually Tesserax, it's what i did from my Time Capsule + Airport Express.
However in my room i cannot get enought signal and only see the Time Capsule wifi network.
Is this normal or shall the airport express network appears differently ?
Thanks for your reply,
Pierre

How do you add an Airport Express to an existing Airport Express network

how do you add an Airport Express to an existing Airport Express network

I assume that you are interested in using the new Express to extend the wireless range of the other.
If so, please check out the following Apple Support article.

Airport Express Network just for Music (Airplay)

Similar Messages

Maybe you are looking for