AirPort Express not connecting to Airport Extreme on Ethernet port

Not sure how to connect the express when using extreme on a ethernet connection.

Got help from Apple, the Airport Express must be configured through a wireless connection first and then the Ethernet connection will pic it up. Which it did.

Similar Messages

I'd like to alter my Airport Extreme/Airport Express wireless network so that the 3 Expresses connect to the Extreme via Ethernet. I've been told this will create a more stable wifi signal. How do I configure this using Airport Utility? Thanks.

I currently have an Airport Extreme Base Station connected to my DSL router by Ethernet. Because I have a long, sprawling home, I have 3 Airport Expresses configured to "Extend the Wireless Network" I've established. Because of my home environment--thick walls encompassaing wire mesh, sprawling rooms, etc., it is hard to maintain a continuously-strong, stable WiFi signal. I've been told that I can create a much more stable network by connecting the Express units to the AEBS via Ethernet cable. Since my home is already wired for Ethernet, I'm considering making this change. If I proceed to establish the Ethernet connections, how do I then set up Airport Utility to accomodate this switch from a Wireless-based WiFi network to an Ethernet-based WiFi network?
Thanks in advance for any help.
Phyllis

I don't see anyplace in the Utility to designate HOW the Express units are connected, only how they relate on the network to the Extreme,
As I mentioned in the previous post, when you click the Internet icon in AirPort Utility:
Connect Using = Ethernet (This tells each Express to connect to the Extreme using the ethernet connection)
Connection Sharing = Off (Bridge Mode) (This setting allows your AirPort Extreme to function as the "main" router on the network, as it must for the setup to work correctly.
You do not need to configure anything differently on the AirPort Extreme (as long as it is working correctly now) to connect the AirPort Express devices.
The only other question I have is the following: I'm currently already using one of the Ethernet ports on the back of the Extreme-- for my husband's iMac. I really don't think he gains much in performance over how the iMac would run through wifi, so I could disconnect the iMac. If you think the iMac would do better to stay on the Ethernet connection, should I use a switch/splitter to add an extra connection?
Since each AirPort Express must connect using ethernet, you will need to use the 3 LAN <-> ports on the AirPort Extreme for the AirPort Express devices.
I would suggest that you try connecting the iMac using wireless to see if that will work. If the wireless connection is not satisfactory, then you can add a 5 port ethernet switch to one of the LAN ports on the Extreme and then plug all the devices connecting using ethernet....the iMac and the 3 AirPort Express devices...into the remaining 4 ports on the switch. That will leave you with 2 open ports on the AirPort Extreme for any future devices that may need to connect.
When you test out the system, here is a trick to find out which device your computer is actually connecting to at any given time as it "roams" around the house.
When you have AirPort Utility open to configure each AirPort Express, jot down the AirPort ID for each Express. You can do the same for the AirPort Extreme.
As you move around with your laptop, hold down the option key on your Mac keyboard while you click on the fan shaped AirPort icon at the top of the screen. Look for the BSSID. That is the AirPort ID of the device that the laptop is connected to at that time. it should also be the ID of the closest AirPort Express (or AirPort Extreme if the laptop is close to the Extreme at the time).
Let us know how things are working when everything is up and running.

Just did firm ware update on time capsule an now my airport express not connected do to air port utilities doesn't support base station ??

just did firm ware update on time capsule an now my airport express not connected do to air port utilities doesn't support base station ?

mickair wrote:
I have been experiencing some networking problems
Welcome to Apple's discussion groups.
I have the latest Time Capsule ("TC"), an old Airport Extreme Base Station ("AEBS") bought in 2007 and 2 Airport Expresses, one bought in 3 months ago ("AE-Alpha") and the other bought back in 2007 ("AE-Beta"). All of them have been updated with the latest firmware.
Based on those dates, the AirPort Extreme is probably flat (as opposed to dome-shaped), making it 802.11n-capable. The Newer AirPort Express is probably an 802.11n-capable model A1264, while the older one is probably a model A1084 or A1088.
I use {the TC's} DHCP function ... to avoid unauthorized use.
This a discussion for another thread, but that's not what DHCP is for.
The wireless setting for it is to participate as WDS Main, but after reading various posts, it seems WDS is a bad idea
With that older AirPort Express you're stuck with WDS unless you decide to replace it with a newer model.
The AEBS is currently setup as being a WDS Relay at the moment
Why a relay? That's only needed if there's another base station "beyond" it that is configured to depend on it.
Since the AEBS is connected to the TC via Ethernet, you should probably configure it as a "roaming network":
http://discussions.apple.com/thread.jspa?threadID=2273124
{The AE-Alpha} connects fine as WDS remote at the moment
I don't have any experience with mixed WDS and non-WDS networks, but since it's 802.11n-capable, you may be able to configure it to "extend" the network of the TC rather than as WDS. Look for a setting on the TC to "Allow this network to be extended".
Physical location:
AEBS in one end, TC and AE-Alpha in the middle while AE-Beta on the other end.
A device such as "AE-Beta" that's supposed to extend a network shouldn't be "at the end" but should be half way between the central base station and the clients that need an extended network.

Airport Extreme (Fast Ethernet) + Airport Express (WDS) = disconnects

I have an Airport Express configured as a WDS, bridging a wired device (a small PC running Linux) to an Airport Extreme (Fast Ethernet). Security is enabled (WPA).
Frequently, the Airport Express disconnects from the wireless network and I have to reboot the thing by unplugging it. I have it set up to log to the PC, but I'm not sure what I should be looking for in the log.
Any guidance? I'd like to hold on to the Express, but I can't if it's acting flakey like this.

More than likely you are experiencing RF interference from other devices operating at 2.4 GHz. You can use a tool like iStumbler to see what other networks are visible in your area. Then you can configure your 2 base stations to use a channel which is as far as possible from the channels used by other networks.

Connecting 2 Airport Extremes via ethernet if my intent is to improve wireless signal in a different area of my home

Connect the second Airport Extreme via ethernet, all is good. However, question is; do I use the same Wireless name as main Airport Extreme or do I need to name is differently? And if differently, how do devices connect to the strongest signal?

Aribia wrote:
Connect the second Airport Extreme via ethernet, all is good. However, question is; do I use the same Wireless name as main Airport Extreme
Yes. If you want your wireless devices to "see" only one wireless network, specify the exact same wireless network name, security and password for the second Extreme.
And if differently, how do devices connect to the strongest signal?
If you choose to specify different names, and your Network Preferences are configured to not "ask to join new networks" your Mac will automatically switch from one to the other, but it does not do this just because one becomes stronger than the other as you move your MacBook Pro away from one and toward the other. It will switch networks when the wireless signal falls below a threshold that is not user-selectable. It will do that whether or not you specify different wireless network names.

Connecting printer to Airport extreme via Ethernet

I have just setup a wireless home network using Airport extreme. My desktop windows xp pc does not have a wireless connection and is connected to the internet by ethernet directly pluged in to the DSL modem.
My Canon printer is connected to the Airport's USB port.
Is there a way I can connect the desktop pc to the printer via the Airport's Ethernet connection?
I appreciate any help, herb

Welcome to the discussions forum Herb.
I have just setup a wireless home network using Airport extreme.
From what you described, you're not done yet.
As I understand it, you're using your MacBook Pro to print to the Canon wirelessly through the Airport Extreme, but your Windows computer can't do that since it has no wireless card. Furthermore, you can't use your MacBook Pro to get on the internet when your DSL modem is connected directly to your PC. Is that right?
The right way to do things is to connect the DSL modem to the *Airport Extreme*, not a computer. Since your PC isn't wireless, its Ethernet port ought to be connected to the Airport's LAN port, and not directly to the DSL modem.
To reconfigure your equipment the right way, do the following:
1. Power down your Windows computer.
2. Unplug the DSL modem.
3. Unplug the Airport Extreme.
4. Power down all your other equipment too, for good measure.
5. Unplug the Windows computer from the DSL modem, and connect it to a LAN port on the Airport Extreme.
6. Using another Ethernet cable, connect the Airport Extreme's WAN port to the DSL modem.
7. Plug in the DSL modem. Wait a few moments for it to complete its power up sequence. Some take longer than others.
8. Plug in the Airport Extreme. After a few moments, its LED should glow steady green, meaning it's communicating with the DSL modem.
If the light blinks amber and never turns green, that means you'll have to reconfigure the Airport using Airport Utility. Not a problem, but if that happens you ought to write back for more help.
9. Boot your computers and the printer. The order isn't important.
Now, check to make sure you can communicate with everything the way you have been used to doing:
1. Log in to your Windows computer and make sure you can load a web page.
2. Log in to your MacBook and make sure you can still print to the Canon.
3. Make sure you can load a web page with your MacBook Pro.
4. Finally, you ought to be able to print with your PC as you're accustomed to. If you can't, you will need to "add a printer" in Windows so it can find the Canon again.
Good luck.

Airport Express as an end point on a wireless network and connect a computer via the ethernet port?

Can I use my Airport Express as an end point on a wireless network and connect a computer via the ethernet port? - I'm wanting to connect a computer that does not have wireless and is in another building.

The requirements for this to work are:
1) The AirPort Express must be the 802.11"n" version. Model Number is A1264
2) There must be adequate wireless signal stength where the Express will be located
3) The Express must be configured to "join" the wireless network with the option checked to activate the Ethernet port

Airport extreme (gigabit ethernet) b/g not working

I have an airport extreme (gigabit ethernet) that I use as my base in an extended network. I Have always had it in Wireless N mode with b/g compatability. the other day my speeds went from being super fast and happy to less than 1mbps. I went and plugged directly in to the airport via ethernet and got blazing fast speeds again.. I switched my radio mode to n only and wireless speeds were fast again.. switched back to b/g compatible and they are in the toilet.. is it possible for the b/g compatible antenna to just crap out? if so this is very disoncerting as I have several wireless devices in my home that operate on b/g and don't want them to be left out in the cold.
Any input is greatly appreciated.

what I did with the b/g testing was I changed the name of the base station to another name so none of the b/g devices that were connecting to it could.. and so it was only the laptop I was using to run the tests.. and still the speeds were terrible.. of course then when I changed it to "n" only mode they were fast again. so I know that my laptop was the only client connected wirelessly or otherwise to the base station when running both tests.
I am extending the network with an airport extreme base station dual band. The solution I have in place currently is to basically swap them. I Have the Dual band running as the main base station in N mode with b/g compatability, and I have the Gigabit ethernet AEBS running as the extender... so far my speeds haven't suffered at all and hopefully it will hold that way. but I still can't understand why the AEBSn would suddenly just stop providing any kind of speed when running as the base in b/g compatibility mode.

HP F4400 printer - connecting to airport extreme via ethernet

I'm trying to install a HP Deskjet F4400 All in One printer on network using Airport Extreme using USB port. Deleted the print driver and reinstalled from the original disk. Unplugged everything and reconnected. Can connect directly to my MacBookPro (OSx v10.6.8) and print just can't print using network. Get "printer offline" message. Any suggestions?

When you use network printing, you can't have the printer selected from the LAST location (USB) because that printer technically doesn't exist anymore because you moved it.
Even though the name of the new location of the printer looks the same as from the last location, technically they are different printers as far as the OSX is concerned.

PowerMac G4 will not connect to the internet via ethernet

I am normally a very mac savy person, but I cannot get this to work...
I have an Airport Express connected to speakers, a USB printer and an ethernet hub, which is connected to a cable modem and also a PowerMac G4 via ethernet. There is also a wireless iMac thrown into the mix. All hardware has up-to-date software.
The wireless iMac gets online, prints and plays music wirelessly.
The wired PowerMac G4 will not connect to the internet via ethernet, it is killing me.
I have gone through all the settings and cannot figure this one out. I really appreciate all advice.
Thanks,
G4 Mac OS X (10.4.8)

Hi pradagirl,
Welcome to Apple Discussions!
Leaving the other peripherals out, tell us the connection sequence from the G4 outbound.
Also, you might gain more insight at the Networking Forum
Regards,
John
G5Dual 2Ghz  23" ACD  iSight Mac OS X (10.4.8)  20" Intel iMac 

MacBook will not connect to the internet via ethernet cable anymore.

My MacBook apparently decided the other day that it no longer desired to connect to the internet through an ethernet connection; it still works perfectly through a wireless network. I am a university student and so there is wireless almost everywhere so it's not so bad, but I cannot connect in my dorm and it's becoming a bit of a pain. I have tried to connect through several known working ethernet ports and no matter what my computer thinks it's not even plugged in. It's even more strange because I just woke up one morning and it was no longer working. Everything else it totally normal, save this one little inconvenience. Any ideas?

So I'm having the same problem. I woke up one morning and my macbook's ethernet connection suddenly stopped working. For some reason It wont recognize the cable.... I have tried 3 different cables and theses cables work with my sisters PC so I know the cable is not the issue. Im also living in college dorms which seems to be a commonality with this issue. I've searched for answers all over and I really don't have the time to make it to the mac store anytime soon. My wireless works but it's not allowed in my college dorms for security reasons(lame). Please help!...
Apple needs to formally address this issue.

Macbook Pro suddenly will not connect to the internet via ethernet cable.

I know this is a long shot... but I figured I would give it a try.
My macbook pro suddenly does not connect to the internet via ethernet cable. Please bear with me, as I am not very tech-savvy - I will try my best to describe the symptoms!
I connect to the internet via ethernet (we don't have wifi). It was working before I went to work, and when I came home I suddenly couldn't get anything to work (I know everyone says this, but I truly didn't mess with anything). Internet browsers just think for awhile and then turn up the 'You are not connected to the internet' error.
I went into my network preferences and curiously, the 'Ethernet' shows a green dot and says 'connected'. However it says 'Authentication server is not responding' underneath the last part that says '802.1X: WPA: eduroam' (I think that is my user profile).
When I go into my 'security' settings I can see that my firewall is off, so that shouldn't be causing any problems.
I've tried restarting the router and computer itself many times. Diagnostics just gets to a certain point and reports back 'Network Diagnostics cannot fix the current networking problems.' I've also tried switching to a different ethernet cable, and I tried both cables out on a PC laptop and it connected without issue. Additionally, I brought my macbook along to a friend's house and it connected to his wifi just fine, so the problem appears to just be with ethernet connections.
I know it's hard to troubleshoot this kind of thing without being there and having a look at the computer yourself, but any tips wouild be greatly appreciated.

As I mentioned above, I am not very tech savvy so I have no idea why a wireless protocol would be showing up there, I'm just listing everything I see in hopes that someone might know something I can try. This is why I am asking for help here - I'm not sure what has happened that has made me unable to connect, especially since it seemingly occured while nobody was using the computer.
I guess I should clarify that I'm not a total hillbilly- normally my firewall is set to 'on', but I set it to 'off' to try and troubleshoot the issues here as I was told that sometimes it can interfere with the computer's ability to connect to the internet. If this is not the case and firewall does not affect anything, I will turn it back on while I try to fix this.
I have tried the method you mentioned above a few times - I actually contacted my ISP earlier this week and they recommended resetting the router like that. They didn't mention any known network issues.

Can time capsule be connected wirelessly and still use ethernet ports for other devices?

can time capsule be connected wirelessly and still use ethernet ports for other devices? we have it connected wirelessly but devices connected to the ethernet ports are not working.

Not as an additional router.. the TC will be plugged into the main router via ethernet (or ethernet equivalent)..
Then the TC is setup in bridge mode. It will simply act as a Switch and HDD.
The wireless can be setup in a number of ways.
From your convenience point of view use it in roaming network mode..
you simply give the TC the same Wireless Name as the existing routers SSID.
Same security setting and password. WPA2 Personal = WPA2 AES which is the best.
But they both use different wireless channels.. normally if you leave the TC on auto it will work fine, but I prefer to control the network.. so set the main router to say 1 and the TC to 11.
You can also use a completely different wireless name etc.. that is up to you. It is still a single flat network and the only thing that is important is only having one router.

How can I receive a fax? The phone jack does not seem to fit in the ethernet port....(OS 10.6.7)

how can I receive a fax? The phone jack does not seem to fit in the ethernet port....(OS 10.6.7)

sarahfromberkeley wrote:
how can I receive a fax? The phone jack does not seem to fit in the ethernet port....(OS 10.6.7)
The MacBook has no fax-modem. You will need an external (USB) modem.
Stedman

Airport extreme and express not connecting

I just purchased a new airport extreme tower. Now my extreme no longer extends the network. I have replugged the express, pressed the reboot button and can see the device in Airport utility but when it tries to configure the express, I get an "Unexpected error--try again". Can anyone help?

Do you have an iPhone or iPad to try the setup of the Express?
If not, are you perhaps running Mavericks (10.9.x) on your Mac, as we see this error in Mavericks at times?

AirPort Express not connecting to Airport Extreme on Ethernet port

Similar Messages

Maybe you are looking for